[v6,0/7] net: phy: adin1100: Add initial support for ADIN1100 industrial PHY

Message

Alexandru Tachici April 12, 2022, 1:06 p.m. UTC

From: Alexandru Tachici <[e-mail]>

The ADIN1100 is a low power single port 10BASE-T1L transceiver designed for
industrial Ethernet applications and is compliant with the IEEE 802.3cg
Ethernet standard for long reach 10 Mb/s Single Pair Ethernet.

The ADIN1100 uses Auto-Negotiation capability in accordance
with IEEE 802.3 Clause 98, providing a mechanism for
exchanging information between PHYs to allow link partners to
agree to a common mode of operation.

The concluded operating mode is the transmit amplitude mode and
master/slave preference common across the two devices.

Both device and LP advertise their ability and request for
increased transmit at:
- BASE-T1 autonegotiation advertisement register [47:32]\
Clause 45.2.7.21 of Standard 802.3
- BIT(13) - 10BASE-T1L High Level Transmit Operating Mode Ability
- BIT(12) - 10BASE-T1L High Level Transmit Operating Mode Request

For 2.4 Vpp (high level transmit) operation, both devices need
to have the High Level Transmit Operating Mode Ability bit set,
and only one of them needs to have the High Level Transmit
Operating Mode Request bit set. Otherwise 1.0 Vpp transmit level
will be used.

Settings for eth1:
	Supported ports: [ TP	 MII ]
	Supported link modes:   10baseT1L/Full
	Supported pause frame use: Symmetric Receive-only
	Supports auto-negotiation: Yes
	Supported FEC modes: Not reported
	Advertised link modes:  10baseT1L/Full
	Advertised pause frame use: No
	Advertised auto-negotiation: Yes
	Advertised FEC modes: Not reported
	Link partner advertised link modes:  10baseT1L/Full
	Link partner advertised pause frame use: No
	Link partner advertised auto-negotiation: Yes
	Link partner advertised FEC modes: Not reported
	Speed: 10Mb/s
	Duplex: Full
	Auto-negotiation: on
	master-slave cfg: preferred slave
	master-slave status: slave
	Port: Twisted Pair
	PHYAD: 0
	Transceiver: external
	MDI-X: Unknown
	Link detected: yes
	SQI: 7/7

1. Add basic support for ADIN1100.

Alexandru Ardelean (1):
  net: phy: adin1100: Add initial support for ADIN1100 industrial PHY

1. Added 10baset-T1L link modes.

2. Added 10-BasetT1L registers.

3. Added Base-T1 auto-negotiation registers. For Base-T1 these
registers decide master/slave status and TX voltage of the
device and link partner.

4. Added 10BASE-T1L support in phy-c45.c. Now genphy functions will call
Base-T1 functions where registers don't match, like the auto-negotiation ones.

5. Convert MSE to SQI using a predefined table and allow user access
through ethtool.

6. DT bindings for the 2.4 Vpp transmit mode.

Alexandru Ardelean (1):
  net: phy: adin1100: Add initial support for ADIN1100 industrial PHY

Alexandru Tachici (6):
  ethtool: Add 10base-T1L link mode entry
  net: phy: Add 10-BaseT1L registers
  net: phy: Add BaseT1 auto-negotiation registers
  net: phy: Add 10BASE-T1L support in phy-c45
  net: phy: adin1100: Add SQI support
  dt-bindings: net: phy: Add 10-baseT1L 2.4 Vpp

Changelog V4 -> V5:
  - added int pma_extable; attribute to struct phy_device;
  - added genphy_c45_baset1_able() function to determine base-t1 ability
  - replaced constant reading of MDIO_PMA_EXTABLE and checking for MDIO_PMA_EXTABLE_BT1 in
phy-c45.c with the genphy_c45_baset1_able() call

Changelog V5 -> V6:
  - in genphy_c45_read_status(): fixed unused variable warning
  - rebased over 5.18
  - in adin_config_aneg(): moved ret value checking out of if() else
  - in adin_set_powerdown_mode(): used ternary instead of if() else

 .../devicetree/bindings/net/ethernet-phy.yaml |   9 +
 drivers/net/phy/Kconfig                       |   7 +
 drivers/net/phy/Makefile                      |   1 +
 drivers/net/phy/adin1100.c                    | 292 ++++++++++++++++++
 drivers/net/phy/phy-c45.c                     | 257 ++++++++++++++-
 drivers/net/phy/phy-core.c                    |   3 +-
 drivers/net/phy/phy_device.c                  |   1 +
 include/linux/mdio.h                          |  70 +++++
 include/linux/phy.h                           |   2 +
 include/uapi/linux/ethtool.h                  |   1 +
 include/uapi/linux/mdio.h                     |  75 +++++
 net/ethtool/common.c                          |   3 +
 12 files changed, 715 insertions(+), 6 deletions(-)
 create mode 100644 drivers/net/phy/adin1100.c

--
2.25.1