diff mbox series

[v4,net-next,15/19] net: mvpp2: add BM protection underrun feature support

Message ID 1611747815-1934-16-git-send-email-stefanc@marvell.com (mailing list archive)
State Superseded
Delegated to: Netdev Maintainers
Headers show
Series net: mvpp2: Add TX Flow Control support | expand

Checks

Context Check Description
netdev/cover_letter success Link
netdev/fixes_present success Link
netdev/patch_count fail Series longer than 15 patches
netdev/tree_selection success Clearly marked for net-next
netdev/subject_prefix success Link
netdev/cc_maintainers success CCed 5 of 5 maintainers
netdev/source_inline success Was 0 now: 0
netdev/verify_signedoff success Link
netdev/module_param fail Was 0 now: 1
netdev/build_32bit success Errors and warnings before: 5 this patch: 5
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/verify_fixes success Link
netdev/checkpatch success total: 0 errors, 0 warnings, 0 checks, 85 lines checked
netdev/build_allmodconfig_warn success Errors and warnings before: 5 this patch: 5
netdev/header_inline success Link
netdev/stable success Stable not CCed

Commit Message

Stefan Chulski Jan. 27, 2021, 11:43 a.m. UTC 
From: Stefan Chulski <stefanc@marvell.com>

Feature double size of BPPI by decreasing number of pools from 16 to 8.
Increasing of BPPI size protect BM drop from BPPI underrun.
Underrun could occurred due to stress on DDR and as result slow buffer
transition from BPPE to BPPI.
New BPPI threshold recommended by spec is:
BPPI low threshold - 640 buffers
BPPI high threshold - 832 buffers
Supported only in PPv23.

Signed-off-by: Stefan Chulski <stefanc@marvell.com>
---
 drivers/net/ethernet/marvell/mvpp2/mvpp2.h      |  8 +++++
 drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c | 35 +++++++++++++++++++-
 2 files changed, 42 insertions(+), 1 deletion(-)
diff mbox series

Patch

diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
index 1d0d8f2..798be58 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2.h
@@ -324,6 +324,10 @@ 
 #define     MVPP2_BM_HIGH_THRESH_MASK		0x7f0000
 #define     MVPP2_BM_HIGH_THRESH_VALUE(val)	((val) << \
 						MVPP2_BM_HIGH_THRESH_OFFS)
+#define     MVPP2_BM_BPPI_HIGH_THRESH		0x1E
+#define     MVPP2_BM_BPPI_LOW_THRESH		0x1C
+#define     MVPP23_BM_BPPI_HIGH_THRESH		0x34
+#define     MVPP23_BM_BPPI_LOW_THRESH		0x28
 #define MVPP2_BM_INTR_CAUSE_REG(pool)		(0x6240 + ((pool) * 4))
 #define     MVPP2_BM_RELEASED_DELAY_MASK	BIT(0)
 #define     MVPP2_BM_ALLOC_FAILED_MASK		BIT(1)
@@ -352,6 +356,10 @@ 
 #define MVPP2_OVERRUN_ETH_DROP			0x7000
 #define MVPP2_CLS_ETH_DROP			0x7020
 
+#define MVPP22_BM_POOL_BASE_ADDR_HIGH_REG	0x6310
+#define     MVPP22_BM_POOL_BASE_ADDR_HIGH_MASK	0xff
+#define     MVPP23_BM_8POOL_MODE		BIT(8)
+
 /* Hit counters registers */
 #define MVPP2_CTRS_IDX				0x7040
 #define     MVPP22_CTRS_TX_CTR(port, txq)	((txq) | ((port) << 3) | BIT(7))
diff --git a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
index eab7d12..6f43881 100644
--- a/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
+++ b/drivers/net/ethernet/marvell/mvpp2/mvpp2_main.c
@@ -70,6 +70,11 @@  enum mvpp2_bm_pool_log_num {
 module_param(queue_mode, int, 0444);
 MODULE_PARM_DESC(queue_mode, "Set queue_mode (single=0, multi=1)");
 
+static int bm_underrun_protect = 1;
+
+module_param(bm_underrun_protect, int, 0444);
+MODULE_PARM_DESC(bm_underrun_protect, "Set BM underrun protect feature (0-1), def=1");
+
 /* Utility/helper methods */
 
 void mvpp2_write(struct mvpp2 *priv, u32 offset, u32 data)
@@ -424,6 +429,21 @@  static int mvpp2_bm_pool_create(struct device *dev, struct mvpp2 *priv,
 
 	val = mvpp2_read(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id));
 	val |= MVPP2_BM_START_MASK;
+
+	val &= ~MVPP2_BM_LOW_THRESH_MASK;
+	val &= ~MVPP2_BM_HIGH_THRESH_MASK;
+
+	/* Set 8 Pools BPPI threshold if BM underrun protection feature
+	 * were enabled
+	 */
+	if (priv->hw_version == MVPP23 && bm_underrun_protect) {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP23_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP23_BM_BPPI_HIGH_THRESH);
+	} else {
+		val |= MVPP2_BM_LOW_THRESH_VALUE(MVPP2_BM_BPPI_LOW_THRESH);
+		val |= MVPP2_BM_HIGH_THRESH_VALUE(MVPP2_BM_BPPI_HIGH_THRESH);
+	}
+
 	mvpp2_write(priv, MVPP2_BM_POOL_CTRL_REG(bm_pool->id), val);
 
 	bm_pool->size = size;
@@ -592,6 +612,16 @@  static int mvpp2_bm_pools_init(struct device *dev, struct mvpp2 *priv)
 	return err;
 }
 
+/* Routine enable PPv23 8 pool mode */
+static void mvpp23_bm_set_8pool_mode(struct mvpp2 *priv)
+{
+	int val;
+
+	val = mvpp2_read(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG);
+	val |= MVPP23_BM_8POOL_MODE;
+	mvpp2_write(priv, MVPP22_BM_POOL_BASE_ADDR_HIGH_REG, val);
+}
+
 static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 {
 	enum dma_data_direction dma_dir = DMA_FROM_DEVICE;
@@ -645,6 +675,9 @@  static int mvpp2_bm_init(struct device *dev, struct mvpp2 *priv)
 	if (!priv->bm_pools)
 		return -ENOMEM;
 
+	if (priv->hw_version == MVPP23 && bm_underrun_protect)
+		mvpp23_bm_set_8pool_mode(priv);
+
 	err = mvpp2_bm_pools_init(dev, priv);
 	if (err < 0)
 		return err;
@@ -6491,7 +6524,7 @@  static void mvpp2_mac_link_up(struct phylink_config *config,
 			     val);
 	}
 
-	if (port->priv->global_tx_fc) {
+	if (port->priv->global_tx_fc && bm_underrun_protect) {
 		port->tx_fc = tx_pause;
 		if (tx_pause)
 			mvpp2_rxq_enable_fc(port);