@@ -65,6 +65,7 @@
DMA_STATUS_MSK_COMMON_LOONGSON)
#define PCI_DEVICE_ID_LOONGSON_GMAC 0x7a03
+#define PCI_DEVICE_ID_LOONGSON_GNET 0x7a13
#define DWMAC_CORE_LS_MULTICHAN 0x10 /* Loongson custom IP */
#define CHANNEL_NUM 8
@@ -148,6 +149,60 @@ static struct stmmac_pci_info loongson_gmac_pci_info = {
.setup = loongson_gmac_data,
};
+static void loongson_gnet_fix_speed(void *priv, unsigned int speed,
+ unsigned int mode)
+{
+ struct loongson_data *ld = (struct loongson_data *)priv;
+ struct net_device *ndev = dev_get_drvdata(ld->dev);
+ struct stmmac_priv *ptr = netdev_priv(ndev);
+
+ /* The integrated PHY has a weird problem with switching from the low
+ * speeds to 1000Mbps mode. The speedup procedure requires the PHY-link
+ * re-negotiation.
+ */
+ if (speed == SPEED_1000) {
+ if (readl(ptr->ioaddr + MAC_CTRL_REG) &
+ GMAC_CONTROL_PS)
+ /* Word around hardware bug, restart autoneg */
+ phy_restart_aneg(ndev->phydev);
+ }
+}
+
+static int loongson_gnet_data(struct pci_dev *pdev,
+ struct plat_stmmacenet_data *plat)
+{
+ struct loongson_data *ld;
+ int i;
+
+ ld = plat->bsp_priv;
+
+ loongson_default_data(pdev, plat);
+
+ if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN) {
+ plat->rx_queues_to_use = CHANNEL_NUM;
+ plat->tx_queues_to_use = CHANNEL_NUM;
+
+ /* Only channel 0 supports checksum,
+ * so turn off checksum to enable multiple channels.
+ */
+ for (i = 1; i < CHANNEL_NUM; i++)
+ plat->tx_queues_cfg[i].coe_unsupported = 1;
+ } else {
+ plat->tx_queues_to_use = 1;
+ plat->rx_queues_to_use = 1;
+ }
+
+ plat->phy_interface = PHY_INTERFACE_MODE_GMII;
+ plat->mdio_bus_data->phy_mask = ~(u32)BIT(2);
+ plat->fix_mac_speed = loongson_gnet_fix_speed;
+
+ return 0;
+}
+
+static struct stmmac_pci_info loongson_gnet_pci_info = {
+ .setup = loongson_gnet_data,
+};
+
static void loongson_dwmac_dma_init_channel(struct stmmac_priv *priv,
void __iomem *ioaddr,
struct stmmac_dma_cfg *dma_cfg,
@@ -293,7 +348,7 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv)
if (!dma)
return NULL;
- /* The Loongson GMAC devices are based on the DW GMAC
+ /* The Loongson GMAC and GNET devices are based on the DW GMAC
* v3.50a and v3.73a IP-cores. But the HW designers have changed the
* GMAC_VERSION.SNPSVER field to the custom 0x10 value on the
* network controllers with the multi-channels feature
@@ -322,9 +377,19 @@ static struct mac_device_info *loongson_dwmac_setup(void *apriv)
if (mac->multicast_filter_bins)
mac->mcast_bits_log2 = ilog2(mac->multicast_filter_bins);
- /* Loongson GMAC doesn't support the flow control. */
- if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC)
+ /* Loongson GMAC doesn't support the flow control. LS2K2000
+ * GNET doesn't support the half-duplex link mode.
+ */
+ if (pdev->device == PCI_DEVICE_ID_LOONGSON_GMAC) {
mac->link.caps = MAC_10 | MAC_100 | MAC_1000;
+ } else {
+ if (ld->loongson_id == DWMAC_CORE_LS_MULTICHAN)
+ mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+ MAC_10 | MAC_100 | MAC_1000;
+ else
+ mac->link.caps = MAC_ASYM_PAUSE | MAC_SYM_PAUSE |
+ MAC_10FD | MAC_100FD | MAC_1000FD;
+ }
mac->link.duplex = GMAC_CONTROL_DM;
mac->link.speed10 = GMAC_CONTROL_PS;
@@ -591,6 +656,7 @@ static SIMPLE_DEV_PM_OPS(loongson_dwmac_pm_ops, loongson_dwmac_suspend,
static const struct pci_device_id loongson_dwmac_id_table[] = {
{ PCI_DEVICE_DATA(LOONGSON, GMAC, &loongson_gmac_pci_info) },
+ { PCI_DEVICE_DATA(LOONGSON, GNET, &loongson_gnet_pci_info) },
{}
};
MODULE_DEVICE_TABLE(pci, loongson_dwmac_id_table);