@@ -384,13 +384,15 @@ static int gsi_evt_ring_alloc_command(struct gsi *gsi, u32 evt_ring_id)
}
ret = evt_ring_command(gsi, evt_ring_id, GSI_EVT_ALLOCATE);
- if (!ret && evt_ring->state != GSI_EVT_RING_STATE_ALLOCATED) {
- dev_err(gsi->dev, "event ring %u bad state %u after alloc\n",
- evt_ring_id, evt_ring->state);
- ret = -EIO;
- }
- return ret;
+ /* If successful the event ring state will have changed */
+ if (evt_ring->state == GSI_EVT_RING_STATE_ALLOCATED)
+ return 0;
+
+ dev_err(gsi->dev, "event ring %u bad state %u after alloc\n",
+ evt_ring_id, evt_ring->state);
+
+ return -EIO;
}
/* Reset a GSI event ring in ALLOCATED or ERROR state. */
@@ -408,9 +410,13 @@ static void gsi_evt_ring_reset_command(struct gsi *gsi, u32 evt_ring_id)
}
ret = evt_ring_command(gsi, evt_ring_id, GSI_EVT_RESET);
- if (!ret && evt_ring->state != GSI_EVT_RING_STATE_ALLOCATED)
- dev_err(gsi->dev, "event ring %u bad state %u after reset\n",
- evt_ring_id, evt_ring->state);
+
+ /* If successful the event ring state will have changed */
+ if (evt_ring->state == GSI_EVT_RING_STATE_ALLOCATED)
+ return;
+
+ dev_err(gsi->dev, "event ring %u bad state %u after reset\n",
+ evt_ring_id, evt_ring->state);
}
/* Issue a hardware de-allocation request for an allocated event ring */
@@ -426,9 +432,13 @@ static void gsi_evt_ring_de_alloc_command(struct gsi *gsi, u32 evt_ring_id)
}
ret = evt_ring_command(gsi, evt_ring_id, GSI_EVT_DE_ALLOC);
- if (!ret && evt_ring->state != GSI_EVT_RING_STATE_NOT_ALLOCATED)
- dev_err(gsi->dev, "event ring %u bad state %u after dealloc\n",
- evt_ring_id, evt_ring->state);
+
+ /* If successful the event ring state will have changed */
+ if (evt_ring->state == GSI_EVT_RING_STATE_NOT_ALLOCATED)
+ return;
+
+ dev_err(gsi->dev, "event ring %u bad state %u after dealloc\n",
+ evt_ring_id, evt_ring->state);
}
/* Fetch the current state of a channel from hardware */
This patch implements the same basic fix for event rings as the previous one does for channels. The result of issuing an event ring control command should be that the event ring changes state. If enabled, a completion interrupt signals that the event ring state has changed. This interrupt is enabled by gsi_evt_ring_command() and disabled again after the command has completed (or we time out). There is a window of time during which the command could complete successfully without interrupting. This would cause the event ring to transition to the desired new state. So whether a event ring command ends via completion interrupt or timeout, we can consider the command successful if the event ring has entered the desired state (and a failure if it has not, regardless of the cause). Fixes: b4175f8731f78 ("net: ipa: only enable GSI event control IRQs when needed") Signed-off-by: Alex Elder <elder@linaro.org> --- drivers/net/ipa/gsi.c | 34 ++++++++++++++++++++++------------ 1 file changed, 22 insertions(+), 12 deletions(-)