diff mbox series

[net-next,v5,5/5] net: sfp: add support for multigig RollBall transceivers

Message ID 20210114044331.5073-6-kabel@kernel.org (mailing list archive)
State Changes Requested
Delegated to: Netdev Maintainers
Headers show
Series Support for RollBall 10G copper SFP modules | expand

Checks

Context Check Description
netdev/cover_letter success Link
netdev/fixes_present success Link
netdev/patch_count success Link
netdev/tree_selection success Clearly marked for net-next
netdev/subject_prefix success Link
netdev/cc_maintainers warning 2 maintainers not CCed: linux@armlinux.org.uk hkallweit1@gmail.com
netdev/source_inline success Was 0 now: 0
netdev/verify_signedoff success Link
netdev/module_param success Was 0 now: 0
netdev/build_32bit success Errors and warnings before: 0 this patch: 0
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/verify_fixes success Link
netdev/checkpatch success total: 0 errors, 0 warnings, 0 checks, 86 lines checked
netdev/build_allmodconfig_warn success Errors and warnings before: 0 this patch: 0
netdev/header_inline success Link
netdev/stable success Stable not CCed

Commit Message

Marek Behún Jan. 14, 2021, 4:43 a.m. UTC 
This adds support for multigig copper SFP modules from RollBall/Hilink.
These modules have a specific way to access clause 45 registers of the
internal PHY.

We also need to wait at least 22 seconds after deasserting TX disable
before accessing the PHY. The code waits for 25 seconds just to be sure.

Signed-off-by: Marek Behún <kabel@kernel.org>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Andrew Lunn <andrew@lunn.ch>
---
 drivers/net/phy/sfp.c | 36 ++++++++++++++++++++++++++++++------
 1 file changed, 30 insertions(+), 6 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/phy/sfp.c b/drivers/net/phy/sfp.c
index d1b655f805ab..9f4270c19380 100644
--- a/drivers/net/phy/sfp.c
+++ b/drivers/net/phy/sfp.c
@@ -166,6 +166,7 @@  static const enum gpiod_flags gpio_flags[] = {
  * on board (for a copper SFP) time to initialise.
  */
 #define T_WAIT			msecs_to_jiffies(50)
+#define T_WAIT_ROLLBALL		msecs_to_jiffies(25000)
 #define T_START_UP		msecs_to_jiffies(300)
 #define T_START_UP_BAD_GPON	msecs_to_jiffies(60000)
 
@@ -205,8 +206,11 @@  static const enum gpiod_flags gpio_flags[] = {
 
 /* SFP modules appear to always have their PHY configured for bus address
  * 0x56 (which with mdio-i2c, translates to a PHY address of 22).
+ * RollBall SFPs access phy via SFP Enhanced Digital Diagnostic Interface
+ * via address 0x51 (mdio-i2c will use RollBall protocol on this address).
  */
-#define SFP_PHY_ADDR	22
+#define SFP_PHY_ADDR		22
+#define SFP_PHY_ADDR_ROLLBALL	17
 
 struct sff_data {
 	unsigned int gpios;
@@ -219,6 +223,7 @@  struct sfp {
 	struct mii_bus *i2c_mii;
 	struct sfp_bus *sfp_bus;
 	enum mdio_i2c_proto mdio_protocol;
+	int phy_addr;
 	struct phy_device *mod_phy;
 	const struct sff_data *type;
 	size_t i2c_block_size;
@@ -251,6 +256,7 @@  struct sfp {
 	struct sfp_eeprom_id id;
 	unsigned int module_power_mW;
 	unsigned int module_t_start_up;
+	unsigned int module_t_wait;
 
 #if IS_ENABLED(CONFIG_HWMON)
 	struct sfp_diag diag;
@@ -1505,7 +1511,7 @@  static int sfp_sm_probe_phy(struct sfp *sfp, bool is_c45)
 	struct phy_device *phy;
 	int err;
 
-	phy = get_phy_device(sfp->i2c_mii, SFP_PHY_ADDR, is_c45);
+	phy = get_phy_device(sfp->i2c_mii, sfp->phy_addr, is_c45);
 	if (phy == ERR_PTR(-ENODEV))
 		return PTR_ERR(phy);
 	if (IS_ERR(phy)) {
@@ -1895,6 +1901,23 @@  static int sfp_sm_mod_probe(struct sfp *sfp, bool report)
 
 	sfp->mdio_protocol = MDIO_I2C_DEFAULT;
 
+	sfp->phy_addr = SFP_PHY_ADDR;
+	sfp->module_t_wait = T_WAIT;
+
+	if (((!memcmp(id.base.vendor_name, "OEM             ", 16) ||
+	      !memcmp(id.base.vendor_name, "Turris          ", 16)) &&
+	     (!memcmp(id.base.vendor_pn, "SFP-10G-T       ", 16) ||
+	      !memcmp(id.base.vendor_pn, "RTSFP-10", 8)))) {
+		sfp->mdio_protocol = MDIO_I2C_ROLLBALL;
+		sfp->phy_addr = SFP_PHY_ADDR_ROLLBALL;
+		sfp->module_t_wait = T_WAIT_ROLLBALL;
+
+		/* RollBall SFPs may have wrong (zero) extended compliance code
+		 * burned in EEPROM. For PHY probing we need the correct one.
+		 */
+		id.base.extended_cc = SFF8024_ECC_10GBASE_T_SFI;
+	}
+
 	return 0;
 }
 
@@ -2090,9 +2113,10 @@  static void sfp_sm_main(struct sfp *sfp, unsigned int event)
 
 		/* We need to check the TX_FAULT state, which is not defined
 		 * while TX_DISABLE is asserted. The earliest we want to do
-		 * anything (such as probe for a PHY) is 50ms.
+		 * anything (such as probe for a PHY) is 50ms. (or more on
+		 * specific modules).
 		 */
-		sfp_sm_next(sfp, SFP_S_WAIT, T_WAIT);
+		sfp_sm_next(sfp, SFP_S_WAIT, sfp->module_t_wait);
 		break;
 
 	case SFP_S_WAIT:
@@ -2106,8 +2130,8 @@  static void sfp_sm_main(struct sfp *sfp, unsigned int event)
 			 * deasserting.
 			 */
 			timeout = sfp->module_t_start_up;
-			if (timeout > T_WAIT)
-				timeout -= T_WAIT;
+			if (timeout > sfp->module_t_wait)
+				timeout -= sfp->module_t_wait;
 			else
 				timeout = 1;