@@ -1197,12 +1197,26 @@ static int ibmvnic_open(struct net_device *netdev)
struct ibmvnic_adapter *adapter = netdev_priv(netdev);
int rc;
- /* If device failover is pending, just set device state and return.
- * Device operation will be handled by reset routine.
+ ASSERT_RTNL();
+
+ /**
+ * If device failover is pending or we are about to reset, just set
+ * device state and return. Device operation will be handled by reset
+ * routine.
+ *
+ * It should be safe to overwrite the adapter->state here. Since
+ * we hold the rtnl, either the reset has not actually started or
+ * the rtnl got dropped during the set_link_state() in do_reset().
+ * In the former case, no one else is changing the state (again we
+ * have the rtnl) and in the latter case, do_reset() will detect and
+ * honor our setting below.
*/
- if (adapter->failover_pending) {
+ if (adapter->failover_pending || (test_bit(0, &adapter->resetting))) {
+ netdev_dbg(netdev, "[S:%d FOP:%d] Resetting, deferring open\n",
+ adapter->state, adapter->failover_pending);
adapter->state = VNIC_OPEN;
- return 0;
+ rc = 0;
+ goto out;
}
if (adapter->state != VNIC_CLOSED) {
@@ -1222,10 +1236,12 @@ static int ibmvnic_open(struct net_device *netdev)
out:
/*
- * If open fails due to a pending failover, set device state and
- * return. Device operation will be handled by reset routine.
+ * If open failed and there is a pending failover or in-progress reset,
+ * set device state and return. Device operation will be handled by
+ * reset routine. See also comments above regarding rtnl.
*/
- if (rc && adapter->failover_pending) {
+ if (rc &&
+ (adapter->failover_pending || (test_bit(0, &adapter->resetting)))) {
adapter->state = VNIC_OPEN;
rc = 0;
}
@@ -1954,6 +1970,14 @@ static int do_reset(struct ibmvnic_adapter *adapter,
if (rwi->reset_reason == VNIC_RESET_FAILOVER)
adapter->failover_pending = false;
+ /* read the state and check (again) after getting rtnl */
+ reset_state = adapter->state;
+
+ if (reset_state == VNIC_REMOVING || reset_state == VNIC_REMOVED) {
+ rc = -EBUSY;
+ goto out;
+ }
+
netif_carrier_off(netdev);
old_num_rx_queues = adapter->req_rx_queues;
@@ -1984,7 +2008,26 @@ static int do_reset(struct ibmvnic_adapter *adapter,
if (rc)
goto out;
+ if (adapter->state == VNIC_OPEN) {
+ /**
+ * When we dropped rtnl, ibmvnic_open() got
+ * it and noticed that we are resetting and
+ * set the adapter state to OPEN. Update our
+ * new "target" state, and resume the reset
+ * from VNIC_CLOSING state.
+ */
+ netdev_dbg(netdev,
+ "Open changed state from %d, updating.\n",
+ reset_state);
+ reset_state = VNIC_OPEN;
+ adapter->state = VNIC_CLOSING;
+ }
+
if (adapter->state != VNIC_CLOSING) {
+ /**
+ * If someone else changed the adapter state
+ * when we dropped the rtnl, fail the reset
+ */
rc = -1;
goto out;
}
@@ -2133,6 +2176,14 @@ static int do_hard_reset(struct ibmvnic_adapter *adapter,
netdev_dbg(adapter->netdev, "Hard resetting driver (%d)\n",
rwi->reset_reason);
+ /* read the state and check (again) after getting rtnl */
+ reset_state = adapter->state;
+
+ if (reset_state == VNIC_REMOVING || reset_state == VNIC_REMOVED) {
+ rc = -EBUSY;
+ goto out;
+ }
+
netif_carrier_off(netdev);
adapter->reset_reason = rwi->reset_reason;
__ibmvnic_reset() currently reads the adapter->state before getting the rtnl and saves that state as the "target state" for the reset. If this read occurs when adapter is in PROBED state, the target state would be PROBED. Just after the target state is saved, and before the actual reset process is started (i.e before rtnl is acquired) if we get an ibmvnic_open() call we would move the adapter to OPEN state. But when the reset is processed (after ibmvnic_open()) drops the rtnl), it will leave the adapter in PROBED state even though we already moved it to OPEN. To fix this, use the RTNL to improve the serialization when reading/updating the adapter state. i.e determine the target state of a reset only after getting the RTNL. And if a reset is in progress during an open, simply set the target state of the adapter and let the reset code finish the open (like we currently do if failover is pending). One twist to this serialization is if the adapter state changes when we drop the RTNL to update the link state. Account for this by checking if there was an intervening open and update the target state for the reset accordingly (see new comments in the code). Note that only the reset functions and ibmvnic_open() can set the adapter to OPEN state and this must happen under rtnl. Fixes: 7d7195a026ba ("ibmvnic: Do not process device remove during device reset") Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com> Reviewed-by: Dany Madden <drt@linux.ibm.com> --- Changelog[v2] [Jakub Kicinski] Use ASSERT_RTNL() instead of WARN_ON_ONCE() and rtnl_is_locked()); --- drivers/net/ethernet/ibm/ibmvnic.c | 65 ++++++++++++++++++++++++++---- 1 file changed, 58 insertions(+), 7 deletions(-)