diff mbox series

[v3,net-next,4/4] Revert "net: ipv4: handle DSA enabled master network devices"

Message ID 20210205133713.4172846-5-vladimir.oltean@nxp.com (mailing list archive)
State Accepted
Commit 46acf7bdbc72f10bb2e86d69c14189c5d45894f4
Delegated to: Netdev Maintainers
Headers show
Series Automatically manage DSA master interface state | expand

Checks

Context Check Description
netdev/cover_letter success Link
netdev/fixes_present success Link
netdev/patch_count success Link
netdev/tree_selection success Clearly marked for net-next
netdev/subject_prefix success Link
netdev/cc_maintainers warning 1 maintainers not CCed: dsahern@kernel.org
netdev/source_inline success Was 0 now: 0
netdev/verify_signedoff success Link
netdev/module_param success Was 0 now: 0
netdev/build_32bit success Errors and warnings before: 1 this patch: 1
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/verify_fixes success Link
netdev/checkpatch success total: 0 errors, 0 warnings, 0 checks, 48 lines checked
netdev/build_allmodconfig_warn success Errors and warnings before: 1 this patch: 1
netdev/header_inline success Link
netdev/stable success Stable not CCed

Commit Message

Vladimir Oltean Feb. 5, 2021, 1:37 p.m. UTC
This reverts commit 728c02089a0e3eefb02e9927bfae50490f40e72e.

Since 2015 DSA has gained more integration with the network stack, we
can now have the same functionality without explicitly open-coding for
it:
- It now opens the DSA master netdevice automatically whenever a user
  netdevice is opened.
- The master and switch interfaces are coupled in an upper/lower
  hierarchy using the netdev adjacency lists.

In the nfsroot example below, the interface chosen by autoconfig was
swp3, and every interface except that and the DSA master, eth1, was
brought down afterwards:

[    8.714215] mscc_felix 0000:00:00.5 swp0 (uninitialized): PHY [0000:00:00.3:10] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[    8.978041] mscc_felix 0000:00:00.5 swp1 (uninitialized): PHY [0000:00:00.3:11] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[    9.246134] mscc_felix 0000:00:00.5 swp2 (uninitialized): PHY [0000:00:00.3:12] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[    9.486203] mscc_felix 0000:00:00.5 swp3 (uninitialized): PHY [0000:00:00.3:13] driver [Microsemi GE VSC8514 SyncE] (irq=POLL)
[    9.512827] mscc_felix 0000:00:00.5: configuring for fixed/internal link mode
[    9.521047] mscc_felix 0000:00:00.5: Link is Up - 2.5Gbps/Full - flow control off
[    9.530382] device eth1 entered promiscuous mode
[    9.535452] DSA: tree 0 setup
[    9.539777] printk: console [netcon0] enabled
[    9.544504] netconsole: network logging started
[    9.555047] fsl_enetc 0000:00:00.2 eth1: configuring for fixed/internal link mode
[    9.562790] fsl_enetc 0000:00:00.2 eth1: Link is Up - 1Gbps/Full - flow control off
[    9.564661] 8021q: adding VLAN 0 to HW filter on device bond0
[    9.637681] fsl_enetc 0000:00:00.0 eth0: PHY [0000:00:00.0:02] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL)
[    9.655679] fsl_enetc 0000:00:00.0 eth0: configuring for inband/sgmii link mode
[    9.666611] mscc_felix 0000:00:00.5 swp0: configuring for inband/qsgmii link mode
[    9.676216] 8021q: adding VLAN 0 to HW filter on device swp0
[    9.682086] mscc_felix 0000:00:00.5 swp1: configuring for inband/qsgmii link mode
[    9.690700] 8021q: adding VLAN 0 to HW filter on device swp1
[    9.696538] mscc_felix 0000:00:00.5 swp2: configuring for inband/qsgmii link mode
[    9.705131] 8021q: adding VLAN 0 to HW filter on device swp2
[    9.710964] mscc_felix 0000:00:00.5 swp3: configuring for inband/qsgmii link mode
[    9.719548] 8021q: adding VLAN 0 to HW filter on device swp3
[    9.747811] Sending DHCP requests ..
[   12.742899] mscc_felix 0000:00:00.5 swp1: Link is Up - 1Gbps/Full - flow control rx/tx
[   12.743828] mscc_felix 0000:00:00.5 swp0: Link is Up - 1Gbps/Full - flow control off
[   12.747062] IPv6: ADDRCONF(NETDEV_CHANGE): swp1: link becomes ready
[   12.755216] fsl_enetc 0000:00:00.0 eth0: Link is Up - 1Gbps/Full - flow control rx/tx
[   12.766603] IPv6: ADDRCONF(NETDEV_CHANGE): swp0: link becomes ready
[   12.783188] mscc_felix 0000:00:00.5 swp2: Link is Up - 1Gbps/Full - flow control rx/tx
[   12.785354] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[   12.799535] IPv6: ADDRCONF(NETDEV_CHANGE): swp2: link becomes ready
[   13.803141] mscc_felix 0000:00:00.5 swp3: Link is Up - 1Gbps/Full - flow control rx/tx
[   13.811646] IPv6: ADDRCONF(NETDEV_CHANGE): swp3: link becomes ready
[   15.452018] ., OK
[   15.470336] IP-Config: Got DHCP answer from 10.0.0.1, my address is 10.0.0.39
[   15.477887] IP-Config: Complete:
[   15.481330]      device=swp3, hwaddr=00:04:9f:05:de:0a, ipaddr=10.0.0.39, mask=255.255.255.0, gw=10.0.0.1
[   15.491846]      host=10.0.0.39, domain=(none), nis-domain=(none)
[   15.498429]      bootserver=10.0.0.1, rootserver=10.0.0.1, rootpath=
[   15.498481]      nameserver0=8.8.8.8
[   15.627542] fsl_enetc 0000:00:00.0 eth0: Link is Down
[   15.690903] mscc_felix 0000:00:00.5 swp0: Link is Down
[   15.745216] mscc_felix 0000:00:00.5 swp1: Link is Down
[   15.800498] mscc_felix 0000:00:00.5 swp2: Link is Down

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
---
Changes in v3:
None.

Changes in v2:
None.

 net/ipv4/ipconfig.c | 21 +++++++++++++++++----
 1 file changed, 17 insertions(+), 4 deletions(-)
diff mbox series

Patch

diff --git a/net/ipv4/ipconfig.c b/net/ipv4/ipconfig.c
index 3cd13e1bc6a7..f9ab1fb219ec 100644
--- a/net/ipv4/ipconfig.c
+++ b/net/ipv4/ipconfig.c
@@ -61,7 +61,6 @@ 
 #include <linux/export.h>
 #include <net/net_namespace.h>
 #include <net/arp.h>
-#include <net/dsa.h>
 #include <net/ip.h>
 #include <net/ipconfig.h>
 #include <net/route.h>
@@ -218,9 +217,9 @@  static int __init ic_open_devs(void)
 	last = &ic_first_dev;
 	rtnl_lock();
 
-	/* bring loopback and DSA master network devices up first */
+	/* bring loopback device up first */
 	for_each_netdev(&init_net, dev) {
-		if (!(dev->flags & IFF_LOOPBACK) && !netdev_uses_dsa(dev))
+		if (!(dev->flags & IFF_LOOPBACK))
 			continue;
 		if (dev_change_flags(dev, dev->flags | IFF_UP, NULL) < 0)
 			pr_err("IP-Config: Failed to open %s\n", dev->name);
@@ -305,6 +304,9 @@  static int __init ic_open_devs(void)
 	return 0;
 }
 
+/* Close all network interfaces except the one we've autoconfigured, and its
+ * lowers, in case it's a stacked virtual interface.
+ */
 static void __init ic_close_devs(void)
 {
 	struct ic_device *d, *next;
@@ -313,9 +315,20 @@  static void __init ic_close_devs(void)
 	rtnl_lock();
 	next = ic_first_dev;
 	while ((d = next)) {
+		bool bring_down = (d != ic_dev);
+		struct net_device *lower_dev;
+		struct list_head *iter;
+
 		next = d->next;
 		dev = d->dev;
-		if (d != ic_dev && !netdev_uses_dsa(dev)) {
+
+		netdev_for_each_lower_dev(ic_dev->dev, lower_dev, iter) {
+			if (dev == lower_dev) {
+				bring_down = false;
+				break;
+			}
+		}
+		if (bring_down) {
 			pr_debug("IP-Config: Downing %s\n", dev->name);
 			dev_change_flags(dev, d->flags, NULL);
 		}