@@ -1279,10 +1279,18 @@
#define MDIO_PMA_10GBR_FECCTRL 0x00ab
#endif
+#ifndef MDIO_PMA_RX_CTRL1
+#define MDIO_PMA_RX_CTRL1 0x8051
+#endif
+
#ifndef MDIO_PCS_DIG_CTRL
#define MDIO_PCS_DIG_CTRL 0x8000
#endif
+#ifndef MDIO_PCS_DIGITAL_STAT
+#define MDIO_PCS_DIGITAL_STAT 0x8010
+#endif
+
#ifndef MDIO_AN_XNP
#define MDIO_AN_XNP 0x0016
#endif
@@ -1358,6 +1366,8 @@
#define XGBE_KR_TRAINING_ENABLE BIT(1)
#define XGBE_PCS_CL37_BP BIT(12)
+#define XGBE_PCS_PSEQ_STATE_MASK 0x1c
+#define XGBE_PCS_PSEQ_STATE_POWER_GOOD 0x10
#define XGBE_AN_CL37_INT_CMPLT BIT(0)
#define XGBE_AN_CL37_INT_MASK 0x01
@@ -1375,6 +1385,10 @@
#define XGBE_PMA_CDR_TRACK_EN_OFF 0x00
#define XGBE_PMA_CDR_TRACK_EN_ON 0x01
+#define XGBE_PMA_RX_RST_0_MASK BIT(4)
+#define XGBE_PMA_RX_RST_0_RESET_ON 0x10
+#define XGBE_PMA_RX_RST_0_RESET_OFF 0x00
+
/* Bit setting and getting macros
* The get macro will extract the current bit field value from within
* the variable
@@ -1953,6 +1953,27 @@ static void xgbe_phy_set_redrv_mode(struct xgbe_prv_data *pdata)
xgbe_phy_put_comm_ownership(pdata);
}
+static void xgbe_phy_rx_reset(struct xgbe_prv_data *pdata)
+{
+ int reg;
+
+ reg = XMDIO_READ_BITS(pdata, MDIO_MMD_PCS, MDIO_PCS_DIGITAL_STAT,
+ XGBE_PCS_PSEQ_STATE_MASK);
+ if (reg == XGBE_PCS_PSEQ_STATE_POWER_GOOD) {
+ /* Mailbox command timed out, reset of RX block is required.
+ * This can be done by asseting the reset bit and wait for
+ * its compeletion.
+ */
+ XMDIO_WRITE_BITS(pdata, MDIO_MMD_PMAPMD, MDIO_PMA_RX_CTRL1,
+ XGBE_PMA_RX_RST_0_MASK, XGBE_PMA_RX_RST_0_RESET_ON);
+ ndelay(20);
+ XMDIO_WRITE_BITS(pdata, MDIO_MMD_PMAPMD, MDIO_PMA_RX_CTRL1,
+ XGBE_PMA_RX_RST_0_MASK, XGBE_PMA_RX_RST_0_RESET_OFF);
+ usleep_range(40, 50);
+ netif_err(pdata, link, pdata->netdev, "firmware mailbox reset performed\n");
+ }
+}
+
static void xgbe_phy_perform_ratechange(struct xgbe_prv_data *pdata,
unsigned int cmd, unsigned int sub_cmd)
{
@@ -1960,9 +1981,11 @@ static void xgbe_phy_perform_ratechange(struct xgbe_prv_data *pdata,
unsigned int wait;
/* Log if a previous command did not complete */
- if (XP_IOREAD_BITS(pdata, XP_DRIVER_INT_RO, STATUS))
+ if (XP_IOREAD_BITS(pdata, XP_DRIVER_INT_RO, STATUS)) {
netif_dbg(pdata, link, pdata->netdev,
"firmware mailbox not ready for command\n");
+ xgbe_phy_rx_reset(pdata);
+ }
/* Construct the command */
XP_SET_BITS(s0, XP_DRIVER_SCRATCH_0, COMMAND, cmd);
@@ -1984,6 +2007,9 @@ static void xgbe_phy_perform_ratechange(struct xgbe_prv_data *pdata,
netif_dbg(pdata, link, pdata->netdev,
"firmware mailbox command did not complete\n");
+
+ /* Reset on error */
+ xgbe_phy_rx_reset(pdata);
}
static void xgbe_phy_rrc(struct xgbe_prv_data *pdata)
Sometimes mailbox commands timeout when the RX data path becomes unresponsive. This prevents the submission of new mailbox commands to DXIO. This patch identifies the timeout and resets the RX data path so that the next message can be submitted properly. Fixes: 549b32af9f7c ("amd-xgbe: Simplify mailbox interface rate change code") Co-developed-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Sudheesh Mavila <sudheesh.mavila@amd.com> Signed-off-by: Shyam Sundar S K <Shyam-sundar.S-k@amd.com> Acked-by: Tom Lendacky <thomas.lendacky@amd.com> --- v1->v2: - Add Co-Developed-by: and Fixes: tag - Changes suggested by Tom on right usage for PSEQ_STATE. drivers/net/ethernet/amd/xgbe/xgbe-common.h | 14 +++++++++++ drivers/net/ethernet/amd/xgbe/xgbe-phy-v2.c | 28 ++++++++++++++++++++- 2 files changed, 41 insertions(+), 1 deletion(-)