diff mbox series

[net,2/6] can: flexcan: enable RX FIFO after FRZ/HALT valid

Message ID 20210301112100.197939-3-mkl@pengutronix.de (mailing list archive)
State Accepted
Delegated to: Netdev Maintainers
Headers show
Series [net,1/6] can: flexcan: assert FRZ bit in flexcan_chip_freeze() | expand

Checks

Context Check Description
netdev/cover_letter success Pull request
netdev/fixes_present success Link
netdev/patch_count success Link
netdev/tree_selection success Clearly marked for net
netdev/subject_prefix success Link
netdev/cc_maintainers fail 2 blamed authors not CCed: wg@grandegger.com s.hauer@pengutronix.de; 2 maintainers not CCed: s.hauer@pengutronix.de wg@grandegger.com
netdev/source_inline success Was 0 now: 0
netdev/verify_signedoff success Link
netdev/module_param success Was 0 now: 0
netdev/build_32bit success Errors and warnings before: 0 this patch: 0
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/verify_fixes success Link
netdev/checkpatch success total: 0 errors, 0 warnings, 0 checks, 17 lines checked
netdev/build_allmodconfig_warn success Errors and warnings before: 0 this patch: 0
netdev/header_inline success Link
netdev/stable success Stable not CCed

Commit Message

Marc Kleine-Budde March 1, 2021, 11:20 a.m. UTC 
From: Joakim Zhang <qiangqing.zhang@nxp.com>

RX FIFO enable failed could happen when do system reboot stress test:

[    0.303958] flexcan 5a8d0000.can: 5a8d0000.can supply xceiver not found, using dummy regulator
[    0.304281] flexcan 5a8d0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[    0.314640] flexcan 5a8d0000.can: registering netdev failed
[    0.320728] flexcan 5a8e0000.can: 5a8e0000.can supply xceiver not found, using dummy regulator
[    0.320991] flexcan 5a8e0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[    0.331360] flexcan 5a8e0000.can: registering netdev failed
[    0.337444] flexcan 5a8f0000.can: 5a8f0000.can supply xceiver not found, using dummy regulator
[    0.337716] flexcan 5a8f0000.can (unnamed net_device) (uninitialized): Could not enable RX FIFO, unsupported core
[    0.348117] flexcan 5a8f0000.can: registering netdev failed

RX FIFO should be enabled after the FRZ/HALT are valid. But the current
code enable RX FIFO and FRZ/HALT at the same time.

Fixes: e955cead03117 ("CAN: Add Flexcan CAN controller driver")
Link: https://lore.kernel.org/r/20210218110037.16591-3-qiangqing.zhang@nxp.com
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
---
 drivers/net/can/flexcan.c | 10 +++++++---
 1 file changed, 7 insertions(+), 3 deletions(-)
diff mbox series

Patch

diff --git a/drivers/net/can/flexcan.c b/drivers/net/can/flexcan.c
index ee2d4967d66a..e66a51dbea0a 100644
--- a/drivers/net/can/flexcan.c
+++ b/drivers/net/can/flexcan.c
@@ -1865,10 +1865,14 @@  static int register_flexcandev(struct net_device *dev)
 	if (err)
 		goto out_chip_disable;
 
-	/* set freeze, halt and activate FIFO, restrict register access */
+	/* set freeze, halt */
+	err = flexcan_chip_freeze(priv);
+	if (err)
+		goto out_chip_disable;
+
+	/* activate FIFO, restrict register access */
 	reg = priv->read(&regs->mcr);
-	reg |= FLEXCAN_MCR_FRZ | FLEXCAN_MCR_HALT |
-		FLEXCAN_MCR_FEN | FLEXCAN_MCR_SUPV;
+	reg |=  FLEXCAN_MCR_FEN | FLEXCAN_MCR_SUPV;
 	priv->write(reg, &regs->mcr);
 
 	/* Currently we only support newer versions of this core