| Message ID | 20210311012108.7190-1-ilya.lipnitskiy@gmail.com (mailing list archive) |
|---|---|
| State | Superseded |
| Delegated to: | Netdev Maintainers |
| Headers | show |
| Series | [net] net: dsa: mt7530: setup core clock even in TRGMII mode | expand |
| Context | Check | Description |
|---|---|---|
| netdev/cover_letter | success | Link |
| netdev/fixes_present | success | Link |
| netdev/patch_count | success | Link |
| netdev/tree_selection | success | Clearly marked for net |
| netdev/subject_prefix | success | Link |
| netdev/cc_maintainers | fail | 3 blamed authors not CCed: sander@svanheule.net tsbogend@alpha.franken.de john@phrozen.org; 3 maintainers not CCed: sander@svanheule.net tsbogend@alpha.franken.de john@phrozen.org |
| netdev/source_inline | success | Was 0 now: 0 |
| netdev/verify_signedoff | success | Link |
| netdev/module_param | success | Was 0 now: 0 |
| netdev/build_32bit | success | Errors and warnings before: 0 this patch: 0 |
| netdev/kdoc | success | Errors and warnings before: 0 this patch: 0 |
| netdev/verify_fixes | success | Link |
| netdev/checkpatch | success | total: 0 errors, 0 warnings, 0 checks, 59 lines checked |
| netdev/build_allmodconfig_warn | success | Errors and warnings before: 0 this patch: 0 |
| netdev/header_inline | success | Link |
On 3/10/2021 5:21 PM, Ilya Lipnitskiy wrote: > A recent change to MIPS ralink reset logic made it so mt7530 actually > resets the switch on platforms such as mt7621 (where bit 2 is the reset > line for the switch). That exposed an issue where the switch would not > function properly in TRGMII mode after a reset. > > Reconfigure core clock in TRGMII mode to fix the issue. > > Tested on Ubiquiti ER-X (MT7621) with TRGMII mode enabled. > > Fixes: 3f9ef7785a9c ("MIPS: ralink: manage low reset lines") > Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
diff --git a/drivers/net/dsa/mt7530.c b/drivers/net/dsa/mt7530.c index f06f5fa2f898..9871d7cff93a 100644 --- a/drivers/net/dsa/mt7530.c +++ b/drivers/net/dsa/mt7530.c @@ -436,34 +436,32 @@ mt7530_pad_clk_setup(struct dsa_switch *ds, phy_interface_t interface) TD_DM_DRVP(8) | TD_DM_DRVN(8)); /* Setup core clock for MT7530 */ - if (!trgint) { - /* Disable MT7530 core clock */ - core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); - - /* Disable PLL, since phy_device has not yet been created - * provided for phy_[read,write]_mmd_indirect is called, we - * provide our own core_write_mmd_indirect to complete this - * function. - */ - core_write_mmd_indirect(priv, - CORE_GSWPLL_GRP1, - MDIO_MMD_VEND2, - 0); - - /* Set core clock into 500Mhz */ - core_write(priv, CORE_GSWPLL_GRP2, - RG_GSWPLL_POSDIV_500M(1) | - RG_GSWPLL_FBKDIV_500M(25)); + /* Disable MT7530 core clock */ + core_clear(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); - /* Enable PLL */ - core_write(priv, CORE_GSWPLL_GRP1, - RG_GSWPLL_EN_PRE | - RG_GSWPLL_POSDIV_200M(2) | - RG_GSWPLL_FBKDIV_200M(32)); - - /* Enable MT7530 core clock */ - core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); - } + /* Disable PLL, since phy_device has not yet been created + * provided for phy_[read,write]_mmd_indirect is called, we + * provide our own core_write_mmd_indirect to complete this + * function. + */ + core_write_mmd_indirect(priv, + CORE_GSWPLL_GRP1, + MDIO_MMD_VEND2, + 0); + + /* Set core clock into 500Mhz */ + core_write(priv, CORE_GSWPLL_GRP2, + RG_GSWPLL_POSDIV_500M(1) | + RG_GSWPLL_FBKDIV_500M(25)); + + /* Enable PLL */ + core_write(priv, CORE_GSWPLL_GRP1, + RG_GSWPLL_EN_PRE | + RG_GSWPLL_POSDIV_200M(2) | + RG_GSWPLL_FBKDIV_200M(32)); + + /* Enable MT7530 core clock */ + core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN); /* Setup the MT7530 TRGMII Tx Clock */ core_set(priv, CORE_TRGMII_GSW_CLK_CG, REG_GSWCK_EN);
A recent change to MIPS ralink reset logic made it so mt7530 actually resets the switch on platforms such as mt7621 (where bit 2 is the reset line for the switch). That exposed an issue where the switch would not function properly in TRGMII mode after a reset. Reconfigure core clock in TRGMII mode to fix the issue. Tested on Ubiquiti ER-X (MT7621) with TRGMII mode enabled. Fixes: 3f9ef7785a9c ("MIPS: ralink: manage low reset lines") Signed-off-by: Ilya Lipnitskiy <ilya.lipnitskiy@gmail.com> --- drivers/net/dsa/mt7530.c | 52 +++++++++++++++++++--------------------- 1 file changed, 25 insertions(+), 27 deletions(-)