diff mbox series

[net-next,v2] net: phy: at803x: fix probe error if copper page is selected

Message ID 20210420102929.13505-1-michael@walle.cc (mailing list archive)
State Accepted
Commit 8f7e876273e294b732b42af2e5e6bba91d798954
Delegated to: Netdev Maintainers
Headers show
Series [net-next,v2] net: phy: at803x: fix probe error if copper page is selected | expand

Checks

Context Check Description
netdev/cover_letter success Link
netdev/fixes_present success Link
netdev/patch_count success Link
netdev/tree_selection success Clearly marked for net-next
netdev/subject_prefix success Link
netdev/cc_maintainers success CCed 7 of 7 maintainers
netdev/source_inline success Was 0 now: 0
netdev/verify_signedoff success Link
netdev/module_param success Was 0 now: 0
netdev/build_32bit fail Errors and warnings before: 6 this patch: 6
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/verify_fixes success Link
netdev/checkpatch success total: 0 errors, 0 warnings, 0 checks, 42 lines checked
netdev/build_allmodconfig_warn success Errors and warnings before: 0 this patch: 0
netdev/header_inline success Link

Commit Message

Michael Walle April 20, 2021, 10:29 a.m. UTC
The commit c329e5afb42f ("net: phy: at803x: select correct page on
config init") selects the copper page during probe. This fails if the
copper page was already selected. In this case, the value of the copper
page (which is 1) is propagated through phy_restore_page() and is
finally returned for at803x_probe(). Fix it, by just using the
at803x_page_write() directly.

Also in case of an error, the regulator is not disabled and leads to a
WARN_ON() when the probe fails. This couldn't happen before, because
at803x_parse_dt() was the last call in at803x_probe(). It is hard to
see, that the parse_dt() actually enables the regulator. Thus move the
regulator_enable() to the probe function and undo it in case of an
error.

Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
Signed-off-by: Michael Walle <michael@walle.cc>
---
Changes since v1:
 - take the bus lock

 drivers/net/phy/at803x.c | 23 +++++++++++++++++------
 1 file changed, 17 insertions(+), 6 deletions(-)

Comments

David Bauer April 20, 2021, 11:04 a.m. UTC | #1
Hi,

On 4/20/21 12:29 PM, Michael Walle wrote:
> The commit c329e5afb42f ("net: phy: at803x: select correct page on
> config init") selects the copper page during probe. This fails if the
> copper page was already selected. In this case, the value of the copper
> page (which is 1) is propagated through phy_restore_page() and is
> finally returned for at803x_probe(). Fix it, by just using the
> at803x_page_write() directly.

Ouch, i didn't spot that. Thanks for taking care.

> 
> Also in case of an error, the regulator is not disabled and leads to a
> WARN_ON() when the probe fails. This couldn't happen before, because
> at803x_parse_dt() was the last call in at803x_probe(). It is hard to
> see, that the parse_dt() actually enables the regulator. Thus move the
> regulator_enable() to the probe function and undo it in case of an
> error.
> 
> Fixes: c329e5afb42f ("net: phy: at803x: select correct page on config init")
> Signed-off-by: Michael Walle <michael@walle.cc>

Reviewed-by: David Bauer <mail@david-bauer.net>

Best
David

> ---
> Changes since v1:
>  - take the bus lock
> 
>  drivers/net/phy/at803x.c | 23 +++++++++++++++++------
>  1 file changed, 17 insertions(+), 6 deletions(-)
> 
> diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
> index e0f56850edc5..32af52dd5aed 100644
> --- a/drivers/net/phy/at803x.c
> +++ b/drivers/net/phy/at803x.c
> @@ -554,10 +554,6 @@ static int at803x_parse_dt(struct phy_device *phydev)
>  			phydev_err(phydev, "failed to get VDDIO regulator\n");
>  			return PTR_ERR(priv->vddio);
>  		}
> -
> -		ret = regulator_enable(priv->vddio);
> -		if (ret < 0)
> -			return ret;
>  	}
>  
>  	return 0;
> @@ -579,15 +575,30 @@ static int at803x_probe(struct phy_device *phydev)
>  	if (ret)
>  		return ret;
>  
> +	if (priv->vddio) {
> +		ret = regulator_enable(priv->vddio);
> +		if (ret < 0)
> +			return ret;
> +	}
> +
>  	/* Some bootloaders leave the fiber page selected.
>  	 * Switch to the copper page, as otherwise we read
>  	 * the PHY capabilities from the fiber side.
>  	 */
>  	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
> -		ret = phy_select_page(phydev, AT803X_PAGE_COPPER);
> -		ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret);
> +		phy_lock_mdio_bus(phydev);
> +		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
> +		phy_unlock_mdio_bus(phydev);
> +		if (ret)
> +			goto err;
>  	}
>  
> +	return 0;
> +
> +err:
> +	if (priv->vddio)
> +		regulator_disable(priv->vddio);
> +
>  	return ret;
>  }
>  
>
patchwork-bot+netdevbpf@kernel.org April 21, 2021, 12:10 a.m. UTC | #2
Hello:

This patch was applied to netdev/net-next.git (refs/heads/master):

On Tue, 20 Apr 2021 12:29:29 +0200 you wrote:
> The commit c329e5afb42f ("net: phy: at803x: select correct page on
> config init") selects the copper page during probe. This fails if the
> copper page was already selected. In this case, the value of the copper
> page (which is 1) is propagated through phy_restore_page() and is
> finally returned for at803x_probe(). Fix it, by just using the
> at803x_page_write() directly.
> 
> [...]

Here is the summary with links:
  - [net-next,v2] net: phy: at803x: fix probe error if copper page is selected
    https://git.kernel.org/netdev/net-next/c/8f7e876273e2

You are awesome, thank you!
--
Deet-doot-dot, I am a bot.
https://korg.docs.kernel.org/patchwork/pwbot.html
diff mbox series

Patch

diff --git a/drivers/net/phy/at803x.c b/drivers/net/phy/at803x.c
index e0f56850edc5..32af52dd5aed 100644
--- a/drivers/net/phy/at803x.c
+++ b/drivers/net/phy/at803x.c
@@ -554,10 +554,6 @@  static int at803x_parse_dt(struct phy_device *phydev)
 			phydev_err(phydev, "failed to get VDDIO regulator\n");
 			return PTR_ERR(priv->vddio);
 		}
-
-		ret = regulator_enable(priv->vddio);
-		if (ret < 0)
-			return ret;
 	}
 
 	return 0;
@@ -579,15 +575,30 @@  static int at803x_probe(struct phy_device *phydev)
 	if (ret)
 		return ret;
 
+	if (priv->vddio) {
+		ret = regulator_enable(priv->vddio);
+		if (ret < 0)
+			return ret;
+	}
+
 	/* Some bootloaders leave the fiber page selected.
 	 * Switch to the copper page, as otherwise we read
 	 * the PHY capabilities from the fiber side.
 	 */
 	if (at803x_match_phy_id(phydev, ATH8031_PHY_ID)) {
-		ret = phy_select_page(phydev, AT803X_PAGE_COPPER);
-		ret = phy_restore_page(phydev, AT803X_PAGE_COPPER, ret);
+		phy_lock_mdio_bus(phydev);
+		ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
+		phy_unlock_mdio_bus(phydev);
+		if (ret)
+			goto err;
 	}
 
+	return 0;
+
+err:
+	if (priv->vddio)
+		regulator_disable(priv->vddio);
+
 	return ret;
 }