@@ -68,11 +68,17 @@
/* PHY Control 1 */
#define MII_KSZPHY_CTRL_1 0x1e
+#define KSZ8081_CTRL1_MDIX_STAT BIT(4)
/* PHY Control 2 / PHY Control (if no PHY Control 1) */
#define MII_KSZPHY_CTRL_2 0x1f
#define MII_KSZPHY_CTRL MII_KSZPHY_CTRL_2
/* bitmap of PHY register to set interrupt mode */
+#define KSZ8081_CTRL2_HP_MDIX BIT(15)
+#define KSZ8081_CTRL2_MDI_MDI_X_SELECT BIT(14)
+#define KSZ8081_CTRL2_DISABLE_AUTO_MDIX BIT(13)
+#define KSZ8081_CTRL2_FORCE_LINK BIT(11)
+#define KSZ8081_CTRL2_POWER_SAVING BIT(10)
#define KSZPHY_CTRL_INT_ACTIVE_HIGH BIT(9)
#define KSZPHY_RMII_REF_CLK_SEL BIT(7)
#define KSZ886X_CTRL_MDIX_STAT BIT(4)
@@ -436,6 +442,87 @@ static int ksz8081_config_init(struct phy_device *phydev)
return kszphy_config_init(phydev);
}
+static int ksz8081_config_mdix(struct phy_device *phydev, u8 ctrl)
+{
+ u16 val;
+
+ switch (ctrl) {
+ case ETH_TP_MDI:
+ val = KSZ8081_CTRL2_DISABLE_AUTO_MDIX;
+ break;
+ case ETH_TP_MDI_X:
+ val = KSZ8081_CTRL2_DISABLE_AUTO_MDIX |
+ KSZ8081_CTRL2_MDI_MDI_X_SELECT;
+ break;
+ case ETH_TP_MDI_AUTO:
+ val = 0;
+ break;
+ default:
+ return 0;
+ }
+
+ return phy_modify(phydev, MII_KSZPHY_CTRL_2,
+ KSZ8081_CTRL2_HP_MDIX |
+ KSZ8081_CTRL2_MDI_MDI_X_SELECT |
+ KSZ8081_CTRL2_DISABLE_AUTO_MDIX,
+ KSZ8081_CTRL2_HP_MDIX | val);
+}
+
+static int ksz8081_config_aneg(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_config_aneg(phydev);
+ if (ret)
+ return ret;
+
+ /* The MDI-X configuration is automatically changed by the PHY after
+ * switching from autoneg off to on. So, take MDI-X configuration under
+ * own control and set it after autoneg configuration was done.
+ */
+ return ksz8081_config_mdix(phydev, phydev->mdix_ctrl);
+}
+
+static int ksz8081_mdix_update(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = phy_read(phydev, MII_KSZPHY_CTRL_2);
+ if (ret < 0)
+ return ret;
+
+ if (ret & KSZ8081_CTRL2_DISABLE_AUTO_MDIX) {
+ if (ret & KSZ8081_CTRL2_MDI_MDI_X_SELECT)
+ phydev->mdix_ctrl = ETH_TP_MDI_X;
+ else
+ phydev->mdix_ctrl = ETH_TP_MDI;
+ } else {
+ phydev->mdix_ctrl = ETH_TP_MDI_AUTO;
+ }
+
+ ret = phy_read(phydev, MII_KSZPHY_CTRL_1);
+ if (ret < 0)
+ return ret;
+
+ if (ret & KSZ8081_CTRL1_MDIX_STAT)
+ phydev->mdix = ETH_TP_MDI;
+ else
+ phydev->mdix = ETH_TP_MDI_X;
+
+ return 0;
+}
+
+static int ksz8081_read_status(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = ksz8081_mdix_update(phydev);
+ if (ret < 0)
+ return ret;
+
+ return genphy_read_status(phydev);
+}
+
static int ksz8061_config_init(struct phy_device *phydev)
{
int ret;
@@ -1423,6 +1510,8 @@ static struct phy_driver ksphy_driver[] = {
.probe = kszphy_probe,
.config_init = ksz8081_config_init,
.soft_reset = genphy_soft_reset,
+ .config_aneg = ksz8081_config_aneg,
+ .read_status = ksz8081_read_status,
.config_intr = kszphy_config_intr,
.handle_interrupt = kszphy_handle_interrupt,
.get_sset_count = kszphy_get_sset_count,
Add support for MDI-X status and configuration Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> --- drivers/net/phy/micrel.c | 89 ++++++++++++++++++++++++++++++++++++++++ 1 file changed, 89 insertions(+)