diff mbox series

[net-next,v5,10/10] arm64: dts: sparx5: Add the Sparx5 switch node

Message ID 20210624070758.515521-11-steen.hegelund@microchip.com (mailing list archive)
State Accepted
Commit d0f482bb06f9447d44d2cae0386a0bd768c3cc16
Delegated to: Netdev Maintainers
Headers show
Series Adding the Sparx5i Switch Driver | expand

Checks

Context Check Description
netdev/cover_letter success Link
netdev/fixes_present success Link
netdev/patch_count success Link
netdev/tree_selection success Clearly marked for net-next
netdev/subject_prefix success Link
netdev/cc_maintainers warning 1 maintainers not CCed: Steen.Hegelund@microchip.com
netdev/source_inline success Was 0 now: 0
netdev/verify_signedoff success Link
netdev/module_param success Was 0 now: 0
netdev/build_32bit success Errors and warnings before: 0 this patch: 0
netdev/kdoc success Errors and warnings before: 0 this patch: 0
netdev/verify_fixes success Link
netdev/checkpatch warning WARNING: DT compatible string "microchip,sparx5-switch-reset" appears un-documented -- check ./Documentation/devicetree/bindings/
netdev/build_allmodconfig_warn success Errors and warnings before: 0 this patch: 0
netdev/header_inline success Link

Commit Message

Steen Hegelund June 24, 2021, 7:07 a.m. UTC 
This provides the configuration for the currently available evaluation
boards PCB134 and PCB135.

The series depends on the following series currently on its way
into the kernel:

- Sparx5 Reset Driver
  Link: https://lore.kernel.org/r/20210416084054.2922327-1-steen.hegelund@microchip.com/

Signed-off-by: Steen Hegelund <steen.hegelund@microchip.com>
Signed-off-by: Lars Povlsen <lars.povlsen@microchip.com>
Signed-off-by: Bjarni Jonasson <bjarni.jonasson@microchip.com>
---
 arch/arm64/boot/dts/microchip/sparx5.dtsi     |  94 ++-
 .../dts/microchip/sparx5_pcb134_board.dtsi    | 481 ++++++++++++--
 .../dts/microchip/sparx5_pcb135_board.dtsi    | 621 +++++++++++++++++-
 3 files changed, 1112 insertions(+), 84 deletions(-)
diff mbox series

Patch

diff --git a/arch/arm64/boot/dts/microchip/sparx5.dtsi b/arch/arm64/boot/dts/microchip/sparx5.dtsi
index d64621d1213b..ad07fff40544 100644
--- a/arch/arm64/boot/dts/microchip/sparx5.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5.dtsi
@@ -135,9 +135,12 @@  mux: mux-controller {
 			};
 		};
 
-		reset@611010008 {
-			compatible = "microchip,sparx5-chip-reset";
+		reset: reset-controller@611010008 {
+			compatible = "microchip,sparx5-switch-reset";
 			reg = <0x6 0x11010008 0x4>;
+			reg-names = "gcb";
+			#reset-cells = <1>;
+			cpu-syscon = <&cpu_ctrl>;
 		};
 
 		uart0: serial@600100000 {
@@ -275,6 +278,21 @@  emmc_pins: emmc-pins {
 					"GPIO_46", "GPIO_47";
 				function = "emmc";
 			};
+
+			miim1_pins: miim1-pins {
+				pins = "GPIO_56", "GPIO_57";
+				function = "miim";
+			};
+
+			miim2_pins: miim2-pins {
+				pins = "GPIO_58", "GPIO_59";
+				function = "miim";
+			};
+
+			miim3_pins: miim3-pins {
+				pins = "GPIO_52", "GPIO_53";
+				function = "miim";
+			};
 		};
 
 		sgpio0: gpio@61101036c {
@@ -285,6 +303,8 @@  sgpio0: gpio@61101036c {
 			clocks = <&sys_clk>;
 			pinctrl-0 = <&sgpio0_pins>;
 			pinctrl-names = "default";
+			resets = <&reset 0>;
+			reset-names = "switch";
 			reg = <0x6 0x1101036c 0x100>;
 			sgpio_in0: gpio@0 {
 				compatible = "microchip,sparx5-sgpio-bank";
@@ -292,6 +312,9 @@  sgpio_in0: gpio@0 {
 				gpio-controller;
 				#gpio-cells = <3>;
 				ngpios = <96>;
+				interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
 			};
 			sgpio_out0: gpio@1 {
 				compatible = "microchip,sparx5-sgpio-bank";
@@ -310,6 +333,8 @@  sgpio1: gpio@611010484 {
 			clocks = <&sys_clk>;
 			pinctrl-0 = <&sgpio1_pins>;
 			pinctrl-names = "default";
+			resets = <&reset 0>;
+			reset-names = "switch";
 			reg = <0x6 0x11010484 0x100>;
 			sgpio_in1: gpio@0 {
 				compatible = "microchip,sparx5-sgpio-bank";
@@ -317,6 +342,9 @@  sgpio_in1: gpio@0 {
 				gpio-controller;
 				#gpio-cells = <3>;
 				ngpios = <96>;
+				interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
 			};
 			sgpio_out1: gpio@1 {
 				compatible = "microchip,sparx5-sgpio-bank";
@@ -335,6 +363,8 @@  sgpio2: gpio@61101059c {
 			clocks = <&sys_clk>;
 			pinctrl-0 = <&sgpio2_pins>;
 			pinctrl-names = "default";
+			resets = <&reset 0>;
+			reset-names = "switch";
 			reg = <0x6 0x1101059c 0x100>;
 			sgpio_in2: gpio@0 {
 				reg = <0>;
@@ -342,6 +372,9 @@  sgpio_in2: gpio@0 {
 				gpio-controller;
 				#gpio-cells = <3>;
 				ngpios = <96>;
+				interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH>;
+				interrupt-controller;
+				#interrupt-cells = <3>;
 			};
 			sgpio_out2: gpio@1 {
 				compatible = "microchip,sparx5-sgpio-bank";
@@ -386,5 +419,62 @@  tmon0: tmon@610508110 {
 			#thermal-sensor-cells = <0>;
 			clocks = <&ahb_clk>;
 		};
+
+		mdio0: mdio@6110102b0 {
+			compatible = "mscc,ocelot-miim";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6 0x110102b0 0x24>;
+		};
+
+		mdio1: mdio@6110102d4 {
+			compatible = "mscc,ocelot-miim";
+			status = "disabled";
+			pinctrl-0 = <&miim1_pins>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6 0x110102d4 0x24>;
+		};
+
+		mdio2: mdio@6110102f8 {
+			compatible = "mscc,ocelot-miim";
+			status = "disabled";
+			pinctrl-0 = <&miim2_pins>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6 0x110102d4 0x24>;
+		};
+
+		mdio3: mdio@61101031c {
+			compatible = "mscc,ocelot-miim";
+			status = "disabled";
+			pinctrl-0 = <&miim3_pins>;
+			pinctrl-names = "default";
+			#address-cells = <1>;
+			#size-cells = <0>;
+			reg = <0x6 0x1101031c 0x24>;
+		};
+
+		serdes: serdes@10808000 {
+			compatible = "microchip,sparx5-serdes";
+			#phy-cells = <1>;
+			clocks = <&sys_clk>;
+			reg = <0x6 0x10808000 0x5d0000>;
+		};
+
+		switch: switch@0x600000000 {
+			compatible = "microchip,sparx5-switch";
+			reg =	<0x6 0 0x401000>,
+				<0x6 0x10004000 0x7fc000>,
+				<0x6 0x11010000 0xaf0000>;
+			reg-names = "cpu", "dev", "gcb";
+			interrupt-names = "xtr";
+			interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>;
+			resets = <&reset 0>;
+			reset-names = "switch";
+		};
 	};
 };
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
index f0c915160990..33faf1f3264f 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb134_board.dtsi
@@ -7,30 +7,6 @@ 
 #include "sparx5_pcb_common.dtsi"
 
 /{
-	aliases {
-	    i2c0   = &i2c0;
-	    i2c100 = &i2c100;
-	    i2c101 = &i2c101;
-	    i2c102 = &i2c102;
-	    i2c103 = &i2c103;
-	    i2c104 = &i2c104;
-	    i2c105 = &i2c105;
-	    i2c106 = &i2c106;
-	    i2c107 = &i2c107;
-	    i2c108 = &i2c108;
-	    i2c109 = &i2c109;
-	    i2c110 = &i2c110;
-	    i2c111 = &i2c111;
-	    i2c112 = &i2c112;
-	    i2c113 = &i2c113;
-	    i2c114 = &i2c114;
-	    i2c115 = &i2c115;
-	    i2c116 = &i2c116;
-	    i2c117 = &i2c117;
-	    i2c118 = &i2c118;
-	    i2c119 = &i2c119;
-	};
-
 	gpio-restart {
 		compatible = "gpio-restart";
 		gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -298,17 +274,10 @@  gpio@1 {
 
 &spi0 {
 	status = "okay";
-	spi@0 {
-		compatible = "spi-mux";
-		mux-controls = <&mux>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0>;	/* CS0 */
-		spi-flash@9 {
-			compatible = "jedec,spi-nor";
-			spi-max-frequency = <8000000>;
-			reg = <0x9>;	/* SPI */
-		};
+	spi-flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <8000000>;
+		reg = <0>;
 	};
 };
 
@@ -328,6 +297,33 @@  spi-flash@9 {
 	};
 };
 
+&sgpio0 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <8 15>;
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
+&sgpio1 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <24 31>;
+	gpio@0 {
+		ngpios = <64>;
+	};
+	gpio@1 {
+		ngpios = <64>;
+	};
+};
+
+&sgpio2 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <0 0>, <11 31>;
+};
+
 &gpio {
 	i2cmux_pins_i: i2cmux-pins-i {
 	       pins = "GPIO_16", "GPIO_17", "GPIO_18", "GPIO_19",
@@ -415,9 +411,9 @@  i2c0_emux: i2c0-emux@0 {
 
 &i2c0_imux {
 	pinctrl-names =
-		"i2c100", "i2c101", "i2c102", "i2c103",
-		"i2c104", "i2c105", "i2c106", "i2c107",
-		"i2c108", "i2c109", "i2c110", "i2c111", "idle";
+		"i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
+		"i2c_sfp5", "i2c_sfp6", "i2c_sfp7", "i2c_sfp8",
+		"i2c_sfp9", "i2c_sfp10", "i2c_sfp11", "i2c_sfp12", "idle";
 	pinctrl-0 = <&i2cmux_0>;
 	pinctrl-1 = <&i2cmux_1>;
 	pinctrl-2 = <&i2cmux_2>;
@@ -431,62 +427,62 @@  &i2c0_imux {
 	pinctrl-10 = <&i2cmux_10>;
 	pinctrl-11 = <&i2cmux_11>;
 	pinctrl-12 = <&i2cmux_pins_i>;
-	i2c100: i2c_sfp1 {
+	i2c_sfp1: i2c_sfp1 {
 		reg = <0x0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c101: i2c_sfp2 {
+	i2c_sfp2: i2c_sfp2 {
 		reg = <0x1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c102: i2c_sfp3 {
+	i2c_sfp3: i2c_sfp3 {
 		reg = <0x2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c103: i2c_sfp4 {
+	i2c_sfp4: i2c_sfp4 {
 		reg = <0x3>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c104: i2c_sfp5 {
+	i2c_sfp5: i2c_sfp5 {
 		reg = <0x4>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c105: i2c_sfp6 {
+	i2c_sfp6: i2c_sfp6 {
 		reg = <0x5>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c106: i2c_sfp7 {
+	i2c_sfp7: i2c_sfp7 {
 		reg = <0x6>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c107: i2c_sfp8 {
+	i2c_sfp8: i2c_sfp8 {
 		reg = <0x7>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c108: i2c_sfp9 {
+	i2c_sfp9: i2c_sfp9 {
 		reg = <0x8>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c109: i2c_sfp10 {
+	i2c_sfp10: i2c_sfp10 {
 		reg = <0x9>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c110: i2c_sfp11 {
+	i2c_sfp11: i2c_sfp11 {
 		reg = <0xa>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c111: i2c_sfp12 {
+	i2c_sfp12: i2c_sfp12 {
 		reg = <0xb>;
 		#address-cells = <1>;
 		#size-cells = <0>;
@@ -499,44 +495,413 @@  &gpio 60 GPIO_ACTIVE_HIGH
 		     &gpio 61 GPIO_ACTIVE_HIGH
 		     &gpio 54 GPIO_ACTIVE_HIGH>;
 	idle-state = <0x8>;
-	i2c112: i2c_sfp13 {
+	i2c_sfp13: i2c_sfp13 {
 		reg = <0x0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c113: i2c_sfp14 {
+	i2c_sfp14: i2c_sfp14 {
 		reg = <0x1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c114: i2c_sfp15 {
+	i2c_sfp15: i2c_sfp15 {
 		reg = <0x2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c115: i2c_sfp16 {
+	i2c_sfp16: i2c_sfp16 {
 		reg = <0x3>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c116: i2c_sfp17 {
+	i2c_sfp17: i2c_sfp17 {
 		reg = <0x4>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c117: i2c_sfp18 {
+	i2c_sfp18: i2c_sfp18 {
 		reg = <0x5>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c118: i2c_sfp19 {
+	i2c_sfp19: i2c_sfp19 {
 		reg = <0x6>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c119: i2c_sfp20 {
+	i2c_sfp20: i2c_sfp20 {
 		reg = <0x7>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
 };
+
+&mdio3 {
+	status = "ok";
+	phy64: ethernet-phy@64 {
+		reg = <28>;
+	};
+};
+
+&axi {
+	sfp_eth12: sfp-eth12 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp1>;
+		tx-disable-gpios = <&sgpio_out2 11 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 11 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 11 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 12 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth13: sfp-eth13 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp2>;
+		tx-disable-gpios = <&sgpio_out2 12 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 12 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 12 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 13 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth14: sfp-eth14 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp3>;
+		tx-disable-gpios = <&sgpio_out2 13 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 13 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 13 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 14 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth15: sfp-eth15 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp4>;
+		tx-disable-gpios = <&sgpio_out2 14 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 14 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 14 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 15 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth48: sfp-eth48 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp5>;
+		tx-disable-gpios = <&sgpio_out2 15 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 15 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 15 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 16 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth49: sfp-eth49 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp6>;
+		tx-disable-gpios = <&sgpio_out2 16 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 16 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 16 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 17 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth50: sfp-eth50 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp7>;
+		tx-disable-gpios = <&sgpio_out2 17 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 17 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 17 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 18 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth51: sfp-eth51 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp8>;
+		tx-disable-gpios = <&sgpio_out2 18 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 18 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 18 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 19 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth52: sfp-eth52 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp9>;
+		tx-disable-gpios = <&sgpio_out2 19 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 19 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 19 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 20 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth53: sfp-eth53 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp10>;
+		tx-disable-gpios = <&sgpio_out2 20 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 20 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 20 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 21 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth54: sfp-eth54 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp11>;
+		tx-disable-gpios = <&sgpio_out2 21 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 21 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 21 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 22 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth55: sfp-eth55 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp12>;
+		tx-disable-gpios = <&sgpio_out2 22 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 22 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 22 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 23 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth56: sfp-eth56 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp13>;
+		tx-disable-gpios = <&sgpio_out2 23 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 23 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 23 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 24 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth57: sfp-eth57 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp14>;
+		tx-disable-gpios = <&sgpio_out2 24 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 24 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 24 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 25 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth58: sfp-eth58 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp15>;
+		tx-disable-gpios = <&sgpio_out2 25 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 25 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 25 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 26 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth59: sfp-eth59 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp16>;
+		tx-disable-gpios = <&sgpio_out2 26 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 26 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 26 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 27 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth60: sfp-eth60 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp17>;
+		tx-disable-gpios = <&sgpio_out2 27 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 27 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 27 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth61: sfp-eth61 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp18>;
+		tx-disable-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 28 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 28 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth62: sfp-eth62 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp19>;
+		tx-disable-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 29 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 29 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth63: sfp-eth63 {
+		compatible       = "sff,sfp";
+		i2c-bus          = <&i2c_sfp20>;
+		tx-disable-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_LOW>;
+		los-gpios        = <&sgpio_in2 30 1 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios   = <&sgpio_in2 30 2 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios   = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&switch {
+	ethernet-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		/* 10G SFPs */
+		port12: port@12 {
+			reg = <12>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 13>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth12>;
+			microchip,sd-sgpio = <301>;
+			managed = "in-band-status";
+		};
+		port13: port@13 {
+			reg = <13>;
+			/* Example: CU SFP, 1G speed */
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 14>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth13>;
+			microchip,sd-sgpio = <305>;
+			managed = "in-band-status";
+		};
+		port14: port@14 {
+			reg = <14>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 15>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth14>;
+			microchip,sd-sgpio = <309>;
+			managed = "in-band-status";
+		};
+		port15: port@15 {
+			reg = <15>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 16>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth15>;
+			microchip,sd-sgpio = <313>;
+			managed = "in-band-status";
+		};
+		port48: port@48 {
+			reg = <48>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 17>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth48>;
+			microchip,sd-sgpio = <317>;
+			managed = "in-band-status";
+		};
+		port49: port@49 {
+			reg = <49>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 18>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth49>;
+			microchip,sd-sgpio = <321>;
+			managed = "in-band-status";
+		};
+		port50: port@50 {
+			reg = <50>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 19>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth50>;
+			microchip,sd-sgpio = <325>;
+			managed = "in-band-status";
+		};
+		port51: port@51 {
+			reg = <51>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 20>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth51>;
+			microchip,sd-sgpio = <329>;
+			managed = "in-band-status";
+		};
+		port52: port@52 {
+			reg = <52>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 21>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth52>;
+			microchip,sd-sgpio = <333>;
+			managed = "in-band-status";
+		};
+		port53: port@53 {
+			reg = <53>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 22>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth53>;
+			microchip,sd-sgpio = <337>;
+			managed = "in-band-status";
+		};
+		port54: port@54 {
+			reg = <54>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 23>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth54>;
+			microchip,sd-sgpio = <341>;
+			managed = "in-band-status";
+		};
+		port55: port@55 {
+			reg = <55>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 24>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth55>;
+			microchip,sd-sgpio = <345>;
+			managed = "in-band-status";
+		};
+		/* 25G SFPs */
+		port56: port@56 {
+			reg = <56>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 25>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth56>;
+			microchip,sd-sgpio = <349>;
+			managed = "in-band-status";
+		};
+		port57: port@57 {
+			reg = <57>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 26>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth57>;
+			microchip,sd-sgpio = <353>;
+			managed = "in-band-status";
+		};
+		port58: port@58 {
+			reg = <58>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 27>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth58>;
+			microchip,sd-sgpio = <357>;
+			managed = "in-band-status";
+		};
+		port59: port@59 {
+			reg = <59>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 28>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth59>;
+			microchip,sd-sgpio = <361>;
+			managed = "in-band-status";
+		};
+		port60: port@60 {
+			reg = <60>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 29>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth60>;
+			microchip,sd-sgpio = <365>;
+			managed = "in-band-status";
+		};
+		port61: port@61 {
+			reg = <61>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 30>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth61>;
+			microchip,sd-sgpio = <369>;
+			managed = "in-band-status";
+		};
+		port62: port@62 {
+			reg = <62>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 31>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth62>;
+			microchip,sd-sgpio = <373>;
+			managed = "in-band-status";
+		};
+		port63: port@63 {
+			reg = <63>;
+			microchip,bandwidth = <10000>;
+			phys = <&serdes 32>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth63>;
+			microchip,sd-sgpio = <377>;
+			managed = "in-band-status";
+		};
+		/* Finally the Management interface */
+		port64: port@64 {
+			reg = <64>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 0>;
+			phy-handle = <&phy64>;
+			phy-mode = "sgmii";
+		};
+	};
+};
diff --git a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
index e28c6dd16377..ef96e6d8c6b3 100644
--- a/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
+++ b/arch/arm64/boot/dts/microchip/sparx5_pcb135_board.dtsi
@@ -7,14 +7,6 @@ 
 #include "sparx5_pcb_common.dtsi"
 
 /{
-	aliases {
-	    i2c0   = &i2c0;
-	    i2c152 = &i2c152;
-	    i2c153 = &i2c153;
-	    i2c154 = &i2c154;
-	    i2c155 = &i2c155;
-	};
-
 	gpio-restart {
 		compatible = "gpio-restart";
 		gpios = <&gpio 37 GPIO_ACTIVE_LOW>;
@@ -97,17 +89,10 @@  i2cmux_s32: i2cmux-3 {
 
 &spi0 {
 	status = "okay";
-	spi@0 {
-		compatible = "spi-mux";
-		mux-controls = <&mux>;
-		#address-cells = <1>;
-		#size-cells = <0>;
-		reg = <0>; /* CS0 */
-		spi-flash@9 {
-			compatible = "jedec,spi-nor";
-			spi-max-frequency = <8000000>;
-			reg = <0x9>; /* SPI */
-		};
+	spi-flash@0 {
+		compatible = "jedec,spi-nor";
+		spi-max-frequency = <8000000>;
+		reg = <0>;
 	};
 };
 
@@ -138,6 +123,11 @@  gpio@1 {
 	};
 };
 
+&sgpio2 {
+	status = "okay";
+	microchip,sgpio-port-ranges = <0 0>, <16 18>, <28 31>;
+};
+
 &axi {
 	i2c0_imux: i2c0-imux@0 {
 		compatible = "i2c-mux-pinctrl";
@@ -149,31 +139,614 @@  i2c0_imux: i2c0-imux@0 {
 
 &i2c0_imux {
 	pinctrl-names =
-		"i2c152", "i2c153", "i2c154", "i2c155",
+		"i2c_sfp1", "i2c_sfp2", "i2c_sfp3", "i2c_sfp4",
 		"idle";
 	pinctrl-0 = <&i2cmux_s29>;
 	pinctrl-1 = <&i2cmux_s30>;
 	pinctrl-2 = <&i2cmux_s31>;
 	pinctrl-3 = <&i2cmux_s32>;
 	pinctrl-4 = <&i2cmux_pins_i>;
-	i2c152: i2c_sfp1 {
+	i2c_sfp1: i2c_sfp1 {
 		reg = <0x0>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c153: i2c_sfp2 {
+	i2c_sfp2: i2c_sfp2 {
 		reg = <0x1>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c154: i2c_sfp3 {
+	i2c_sfp3: i2c_sfp3 {
 		reg = <0x2>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
-	i2c155: i2c_sfp4 {
+	i2c_sfp4: i2c_sfp4 {
 		reg = <0x3>;
 		#address-cells = <1>;
 		#size-cells = <0>;
 	};
 };
+
+&axi {
+	sfp_eth60: sfp-eth60 {
+		compatible	   = "sff,sfp";
+		i2c-bus            = <&i2c_sfp1>;
+		tx-disable-gpios   = <&sgpio_out2 28 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 28 1 GPIO_ACTIVE_HIGH>;
+		los-gpios          = <&sgpio_in2 28 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios     = <&sgpio_in2 28 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios     = <&sgpio_in2 28 2 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth61: sfp-eth61 {
+		compatible         = "sff,sfp";
+		i2c-bus            = <&i2c_sfp2>;
+		tx-disable-gpios   = <&sgpio_out2 29 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 29 1 GPIO_ACTIVE_HIGH>;
+		los-gpios          = <&sgpio_in2 29 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios     = <&sgpio_in2 29 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios     = <&sgpio_in2 29 2 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth62: sfp-eth62 {
+		compatible         = "sff,sfp";
+		i2c-bus            = <&i2c_sfp3>;
+		tx-disable-gpios   = <&sgpio_out2 30 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 30 1 GPIO_ACTIVE_HIGH>;
+		los-gpios          = <&sgpio_in2 30 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios     = <&sgpio_in2 30 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios     = <&sgpio_in2 30 2 GPIO_ACTIVE_HIGH>;
+	};
+	sfp_eth63: sfp-eth63 {
+		compatible         = "sff,sfp";
+		i2c-bus            = <&i2c_sfp4>;
+		tx-disable-gpios   = <&sgpio_out2 31 0 GPIO_ACTIVE_LOW>;
+		rate-select0-gpios = <&sgpio_out2 31 1 GPIO_ACTIVE_HIGH>;
+		los-gpios          = <&sgpio_in2 31 0 GPIO_ACTIVE_HIGH>;
+		mod-def0-gpios     = <&sgpio_in2 31 1 GPIO_ACTIVE_LOW>;
+		tx-fault-gpios     = <&sgpio_in2 31 2 GPIO_ACTIVE_HIGH>;
+	};
+};
+
+&mdio0 {
+	status = "ok";
+	phy0: ethernet-phy@0 {
+		reg = <0>;
+	};
+	phy1: ethernet-phy@1 {
+		reg = <1>;
+	};
+	phy2: ethernet-phy@2 {
+		reg = <2>;
+	};
+	phy3: ethernet-phy@3 {
+		reg = <3>;
+	};
+	phy4: ethernet-phy@4 {
+		reg = <4>;
+	};
+	phy5: ethernet-phy@5 {
+		reg = <5>;
+	};
+	phy6: ethernet-phy@6 {
+		reg = <6>;
+	};
+	phy7: ethernet-phy@7 {
+		reg = <7>;
+	};
+	phy8: ethernet-phy@8 {
+		reg = <8>;
+	};
+	phy9: ethernet-phy@9 {
+		reg = <9>;
+	};
+	phy10: ethernet-phy@10 {
+		reg = <10>;
+	};
+	phy11: ethernet-phy@11 {
+		reg = <11>;
+	};
+	phy12: ethernet-phy@12 {
+		reg = <12>;
+	};
+	phy13: ethernet-phy@13 {
+		reg = <13>;
+	};
+	phy14: ethernet-phy@14 {
+		reg = <14>;
+	};
+	phy15: ethernet-phy@15 {
+		reg = <15>;
+	};
+	phy16: ethernet-phy@16 {
+		reg = <16>;
+	};
+	phy17: ethernet-phy@17 {
+		reg = <17>;
+	};
+	phy18: ethernet-phy@18 {
+		reg = <18>;
+	};
+	phy19: ethernet-phy@19 {
+		reg = <19>;
+	};
+	phy20: ethernet-phy@20 {
+		reg = <20>;
+	};
+	phy21: ethernet-phy@21 {
+		reg = <21>;
+	};
+	phy22: ethernet-phy@22 {
+		reg = <22>;
+	};
+	phy23: ethernet-phy@23 {
+		reg = <23>;
+	};
+};
+
+&mdio1 {
+	status = "ok";
+	phy24: ethernet-phy@24 {
+		reg = <0>;
+	};
+	phy25: ethernet-phy@25 {
+		reg = <1>;
+	};
+	phy26: ethernet-phy@26 {
+		reg = <2>;
+	};
+	phy27: ethernet-phy@27 {
+		reg = <3>;
+	};
+	phy28: ethernet-phy@28 {
+		reg = <4>;
+	};
+	phy29: ethernet-phy@29 {
+		reg = <5>;
+	};
+	phy30: ethernet-phy@30 {
+		reg = <6>;
+	};
+	phy31: ethernet-phy@31 {
+		reg = <7>;
+	};
+	phy32: ethernet-phy@32 {
+		reg = <8>;
+	};
+	phy33: ethernet-phy@33 {
+		reg = <9>;
+	};
+	phy34: ethernet-phy@34 {
+		reg = <10>;
+	};
+	phy35: ethernet-phy@35 {
+		reg = <11>;
+	};
+	phy36: ethernet-phy@36 {
+		reg = <12>;
+	};
+	phy37: ethernet-phy@37 {
+		reg = <13>;
+	};
+	phy38: ethernet-phy@38 {
+		reg = <14>;
+	};
+	phy39: ethernet-phy@39 {
+		reg = <15>;
+	};
+	phy40: ethernet-phy@40 {
+		reg = <16>;
+	};
+	phy41: ethernet-phy@41 {
+		reg = <17>;
+	};
+	phy42: ethernet-phy@42 {
+		reg = <18>;
+	};
+	phy43: ethernet-phy@43 {
+		reg = <19>;
+	};
+	phy44: ethernet-phy@44 {
+		reg = <20>;
+	};
+	phy45: ethernet-phy@45 {
+		reg = <21>;
+	};
+	phy46: ethernet-phy@46 {
+		reg = <22>;
+	};
+	phy47: ethernet-phy@47 {
+		reg = <23>;
+	};
+};
+
+&mdio3 {
+	status = "ok";
+	phy64: ethernet-phy@64 {
+		reg = <28>;
+	};
+};
+
+&switch {
+	ethernet-ports {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		port0: port@0 {
+			reg = <0>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 13>;
+			phy-handle = <&phy0>;
+			phy-mode = "qsgmii";
+		};
+		port1: port@1 {
+			reg = <1>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 13>;
+			phy-handle = <&phy1>;
+			phy-mode = "qsgmii";
+		};
+		port2: port@2 {
+			reg = <2>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 13>;
+			phy-handle = <&phy2>;
+			phy-mode = "qsgmii";
+		};
+		port3: port@3 {
+			reg = <3>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 13>;
+			phy-handle = <&phy3>;
+			phy-mode = "qsgmii";
+		};
+		port4: port@4 {
+			reg = <4>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 14>;
+			phy-handle = <&phy4>;
+			phy-mode = "qsgmii";
+		};
+		port5: port@5 {
+			reg = <5>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 14>;
+			phy-handle = <&phy5>;
+			phy-mode = "qsgmii";
+		};
+		port6: port@6 {
+			reg = <6>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 14>;
+			phy-handle = <&phy6>;
+			phy-mode = "qsgmii";
+		};
+		port7: port@7 {
+			reg = <7>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 14>;
+			phy-handle = <&phy7>;
+			phy-mode = "qsgmii";
+		};
+		port8: port@8 {
+			reg = <8>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 15>;
+			phy-handle = <&phy8>;
+			phy-mode = "qsgmii";
+		};
+		port9: port@9 {
+			reg = <9>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 15>;
+			phy-handle = <&phy9>;
+			phy-mode = "qsgmii";
+		};
+		port10: port@10 {
+			reg = <10>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 15>;
+			phy-handle = <&phy10>;
+			phy-mode = "qsgmii";
+		};
+		port11: port@11 {
+			reg = <11>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 15>;
+			phy-handle = <&phy11>;
+			phy-mode = "qsgmii";
+		};
+		port12: port@12 {
+			reg = <12>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 16>;
+			phy-handle = <&phy12>;
+			phy-mode = "qsgmii";
+		};
+		port13: port@13 {
+			reg = <13>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 16>;
+			phy-handle = <&phy13>;
+			phy-mode = "qsgmii";
+		};
+		port14: port@14 {
+			reg = <14>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 16>;
+			phy-handle = <&phy14>;
+			phy-mode = "qsgmii";
+		};
+		port15: port@15 {
+			reg = <15>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 16>;
+			phy-handle = <&phy15>;
+			phy-mode = "qsgmii";
+		};
+		port16: port@16 {
+			reg = <16>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 17>;
+			phy-handle = <&phy16>;
+			phy-mode = "qsgmii";
+		};
+		port17: port@17 {
+			reg = <17>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 17>;
+			phy-handle = <&phy17>;
+			phy-mode = "qsgmii";
+		};
+		port18: port@18 {
+			reg = <18>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 17>;
+			phy-handle = <&phy18>;
+			phy-mode = "qsgmii";
+		};
+		port19: port@19 {
+			reg = <19>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 17>;
+			phy-handle = <&phy19>;
+			phy-mode = "qsgmii";
+		};
+		port20: port@20 {
+			reg = <20>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 18>;
+			phy-handle = <&phy20>;
+			phy-mode = "qsgmii";
+		};
+		port21: port@21 {
+			reg = <21>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 18>;
+			phy-handle = <&phy21>;
+			phy-mode = "qsgmii";
+		};
+		port22: port@22 {
+			reg = <22>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 18>;
+			phy-handle = <&phy22>;
+			phy-mode = "qsgmii";
+		};
+		port23: port@23 {
+			reg = <23>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 18>;
+			phy-handle = <&phy23>;
+			phy-mode = "qsgmii";
+		};
+		port24: port@24 {
+			reg = <24>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 19>;
+			phy-handle = <&phy24>;
+			phy-mode = "qsgmii";
+		};
+		port25: port@25 {
+			reg = <25>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 19>;
+			phy-handle = <&phy25>;
+			phy-mode = "qsgmii";
+		};
+		port26: port@26 {
+			reg = <26>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 19>;
+			phy-handle = <&phy26>;
+			phy-mode = "qsgmii";
+		};
+		port27: port@27 {
+			reg = <27>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 19>;
+			phy-handle = <&phy27>;
+			phy-mode = "qsgmii";
+		};
+		port28: port@28 {
+			reg = <28>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 20>;
+			phy-handle = <&phy28>;
+			phy-mode = "qsgmii";
+		};
+		port29: port@29 {
+			reg = <29>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 20>;
+			phy-handle = <&phy29>;
+			phy-mode = "qsgmii";
+		};
+		port30: port@30 {
+			reg = <30>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 20>;
+			phy-handle = <&phy30>;
+			phy-mode = "qsgmii";
+		};
+		port31: port@31 {
+			reg = <31>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 20>;
+			phy-handle = <&phy31>;
+			phy-mode = "qsgmii";
+		};
+		port32: port@32 {
+			reg = <32>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 21>;
+			phy-handle = <&phy32>;
+			phy-mode = "qsgmii";
+		};
+		port33: port@33 {
+			reg = <33>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 21>;
+			phy-handle = <&phy33>;
+			phy-mode = "qsgmii";
+		};
+		port34: port@34 {
+			reg = <34>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 21>;
+			phy-handle = <&phy34>;
+			phy-mode = "qsgmii";
+		};
+		port35: port@35 {
+			reg = <35>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 21>;
+			phy-handle = <&phy35>;
+			phy-mode = "qsgmii";
+		};
+		port36: port@36 {
+			reg = <36>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 22>;
+			phy-handle = <&phy36>;
+			phy-mode = "qsgmii";
+		};
+		port37: port@37 {
+			reg = <37>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 22>;
+			phy-handle = <&phy37>;
+			phy-mode = "qsgmii";
+		};
+		port38: port@38 {
+			reg = <38>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 22>;
+			phy-handle = <&phy38>;
+			phy-mode = "qsgmii";
+		};
+		port39: port@39 {
+			reg = <39>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 22>;
+			phy-handle = <&phy39>;
+			phy-mode = "qsgmii";
+		};
+		port40: port@40 {
+			reg = <40>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 23>;
+			phy-handle = <&phy40>;
+			phy-mode = "qsgmii";
+		};
+		port41: port@41 {
+			reg = <41>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 23>;
+			phy-handle = <&phy41>;
+			phy-mode = "qsgmii";
+		};
+		port42: port@42 {
+			reg = <42>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 23>;
+			phy-handle = <&phy42>;
+			phy-mode = "qsgmii";
+		};
+		port43: port@43 {
+			reg = <43>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 23>;
+			phy-handle = <&phy43>;
+			phy-mode = "qsgmii";
+		};
+		port44: port@44 {
+			reg = <44>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 24>;
+			phy-handle = <&phy44>;
+			phy-mode = "qsgmii";
+		};
+		port45: port@45 {
+			reg = <45>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 24>;
+			phy-handle = <&phy45>;
+			phy-mode = "qsgmii";
+		};
+		port46: port@46 {
+			reg = <46>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 24>;
+			phy-handle = <&phy46>;
+			phy-mode = "qsgmii";
+		};
+		port47: port@47 {
+			reg = <47>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 24>;
+			phy-handle = <&phy47>;
+			phy-mode = "qsgmii";
+		};
+		/* Then the 25G interfaces */
+		port60: port@60 {
+			reg = <60>;
+			microchip,bandwidth = <25000>;
+			phys = <&serdes 29>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth60>;
+			managed = "in-band-status";
+		};
+		port61: port@61 {
+			reg = <61>;
+			microchip,bandwidth = <25000>;
+			phys = <&serdes 30>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth61>;
+			managed = "in-band-status";
+		};
+		port62: port@62 {
+			reg = <62>;
+			microchip,bandwidth = <25000>;
+			phys = <&serdes 31>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth62>;
+			managed = "in-band-status";
+		};
+		port63: port@63 {
+			reg = <63>;
+			microchip,bandwidth = <25000>;
+			phys = <&serdes 32>;
+			phy-mode = "10gbase-r";
+			sfp = <&sfp_eth63>;
+			managed = "in-band-status";
+		};
+		/* Finally the Management interface */
+		port64: port@64 {
+			reg = <64>;
+			microchip,bandwidth = <1000>;
+			phys = <&serdes 0>;
+			phy-handle = <&phy64>;
+			phy-mode = "sgmii";
+		};
+	};
+};