@@ -83,6 +83,13 @@ config ADIN_PHY
- ADIN1300 - Robust,Industrial, Low Latency 10/100/1000 Gigabit
Ethernet PHY
+config ADIN1100_PHY
+ tristate "Analog Devices Industrial Ethernet T1L PHYs"
+ help
+ Adds support for the Analog Devices Industrial T1L Ethernet PHYs.
+ Currently supports the:
+ - ADIN1100 - Robust,Industrial, Low Power 10BASE-T1L Ethernet PHY
+
config AQUANTIA_PHY
tristate "Aquantia PHYs"
help
@@ -31,6 +31,7 @@ sfp-obj-$(CONFIG_SFP) += sfp-bus.o
obj-y += $(sfp-obj-y) $(sfp-obj-m)
obj-$(CONFIG_ADIN_PHY) += adin.o
+obj-$(CONFIG_ADIN1100_PHY) += adin1100.o
obj-$(CONFIG_AMD_PHY) += amd.o
aquantia-objs += aquantia_main.o
ifdef CONFIG_HWMON
new file mode 100644
@@ -0,0 +1,437 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
+/**
+ * Driver for Analog Devices Industrial Ethernet T1L PHYs
+ *
+ * Copyright 2020 Analog Devices Inc.
+ */
+#include <linux/kernel.h>
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/errno.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/mii.h>
+#include <linux/phy.h>
+#include <linux/property.h>
+
+#define PHY_ID_ADIN1100 0x0283bc81
+
+static const int phy_10_features_array[] = {
+ ETHTOOL_LINK_MODE_10baseT_Full_BIT,
+};
+
+#define ADIN_B10L_PCS_CNTRL 0x08e6
+#define ADIN_PCS_CNTRL_B10L_LB_PCS_EN BIT(14)
+
+#define ADIN_B10L_PMA_CNTRL 0x08f6
+#define ADIN_PMA_CNTRL_B10L_LB_PMA_LOC_EN BIT(0)
+
+#define ADIN_B10L_PMA_STAT 0x08f7
+#define ADIN_PMA_STAT_B10L_LB_PMA_LOC_ABLE BIT(13)
+#define ADIN_PMA_STAT_B10L_TX_LVL_HI_ABLE BIT(12)
+
+#define ADIN_AN_CONTROL 0x0200
+#define ADIN_AN_RESTART BIT(9)
+#define ADIN_AN_EN BIT(12)
+
+#define ADIN_AN_STATUS 0x0201
+#define ADIN_AN_ADV_ABILITY_L 0x0202
+#define ADIN_AN_ADV_ABILITY_M 0x0203
+#define ADIN_AN_ADV_ABILITY_H 0x0204U
+#define ADIN_AN_ADV_B10L_TX_LVL_HI_ABL BIT(13)
+#define ADIN_AN_ADV_B10L_TX_LVL_HI_REQ BIT(12)
+
+#define ADIN_AN_LP_ADV_ABILITY_L 0x0205
+
+#define ADIN_AN_LP_ADV_ABILITY_M 0x0206
+#define ADIN_AN_LP_ADV_B10L BIT(14)
+#define ADIN_AN_LP_ADV_B1000 BIT(7)
+#define ADIN_AN_LP_ADV_B10S_FD BIT(6)
+#define ADIN_AN_LP_ADV_B100 BIT(5)
+#define ADIN_AN_LP_ADV_MST BIT(4)
+
+#define ADIN_AN_LP_ADV_ABILITY_H 0x0207
+#define ADIN_AN_LP_ADV_B10L_EEE BIT(14)
+#define ADIN_AN_LP_ADV_B10L_TX_LVL_HI_ABL BIT(13)
+#define ADIN_AN_LP_ADV_B10L_TX_LVL_HI_REQ BIT(12)
+#define ADIN_AN_LP_ADV_B10S_HD BIT(11)
+
+#define ADIN_CRSM_SFT_RST 0x8810
+#define ADIN_CRSM_SFT_RST_EN BIT(0)
+
+#define ADIN_CRSM_SFT_PD_CNTRL 0x8812
+#define ADIN_CRSM_SFT_PD_CNTRL_EN BIT(0)
+
+#define ADIN_CRSM_STAT 0x8818
+#define ADIN_CRSM_SFT_PD_RDY BIT(1)
+#define ADIN_CRSM_SYS_RDY BIT(0)
+
+#define ADIN_MAC_IF_LOOPBACK 0x803d
+#define ADIN_MAC_IF_LOOPBACK_EN BIT(0)
+#define ADIN_MAC_IF_REMOTE_LOOPBACK_EN BIT(2)
+
+/**
+ * struct adin_priv - ADIN PHY driver private data
+ * tx_level_24v set if the PHY supports 2.4V TX levels (10BASE-T1L)
+ */
+struct adin_priv {
+ unsigned int tx_level_24v:1;
+};
+
+static int adin_match_phy_device(struct phy_device *phydev)
+{
+ struct mii_bus *bus = phydev->mdio.bus;
+ int phy_addr = phydev->mdio.addr;
+ u32 id;
+ int rc;
+
+ mutex_lock(&bus->mdio_lock);
+
+ /* Need to call __mdiobus_read() directly here, because at this point
+ * in time, the driver isn't attached to the PHY device.
+ */
+ rc = __mdiobus_read(bus, phy_addr, MDIO_DEVID1);
+ if (rc < 0) {
+ mutex_unlock(&bus->mdio_lock);
+ return rc;
+ }
+
+ id = rc << 16;
+
+ rc = __mdiobus_read(bus, phy_addr, MDIO_DEVID2);
+ mutex_unlock(&bus->mdio_lock);
+
+ if (rc < 0)
+ return rc;
+
+ id |= rc;
+
+ switch (id) {
+ case PHY_ID_ADIN1100:
+ return 1;
+ default:
+ return 0;
+ }
+}
+
+static void adin_mii_adv_m_to_ethtool_adv_t(unsigned long *advertising, u32 adv)
+{
+ if (adv & ADIN_AN_LP_ADV_B10L)
+ linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, advertising);
+ if (adv & ADIN_AN_LP_ADV_B1000) {
+ linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Half_BIT, advertising);
+ linkmode_set_bit(ETHTOOL_LINK_MODE_1000baseT_Full_BIT, advertising);
+ }
+ if (adv & ADIN_AN_LP_ADV_B10S_FD)
+ linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, advertising);
+ if (adv & ADIN_AN_LP_ADV_B100)
+ linkmode_set_bit(ETHTOOL_LINK_MODE_100baseT_Full_BIT, advertising);
+}
+
+static void adin_mii_adv_h_to_ethtool_adv_t(unsigned long *advertising, u32 adv)
+{
+ if (adv & ADIN_AN_LP_ADV_B10S_HD)
+ linkmode_set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, advertising);
+}
+
+static int adin_read_lpa(struct phy_device *phydev)
+{
+ int val;
+
+ linkmode_zero(phydev->lp_advertising);
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_STATUS);
+ if (val < 0)
+ return val;
+
+ if (!(val & MDIO_AN_STAT1_COMPLETE)) {
+ phydev->pause = 0;
+ phydev->asym_pause = 0;
+
+ return 0;
+ }
+
+ linkmode_set_bit(ETHTOOL_LINK_MODE_Autoneg_BIT,
+ phydev->lp_advertising);
+
+ /* Read the link partner's base page advertisement */
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_LP_ADV_ABILITY_L);
+ if (val < 0)
+ return val;
+
+ phydev->pause = val & LPA_PAUSE_CAP ? 1 : 0;
+ phydev->asym_pause = val & LPA_PAUSE_ASYM ? 1 : 0;
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_LP_ADV_ABILITY_M);
+ if (val < 0)
+ return val;
+
+ adin_mii_adv_m_to_ethtool_adv_t(phydev->lp_advertising, val);
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_LP_ADV_ABILITY_H);
+ if (val < 0)
+ return val;
+
+ adin_mii_adv_h_to_ethtool_adv_t(phydev->lp_advertising, val);
+
+ return 0;
+}
+
+static int adin_read_status(struct phy_device *phydev)
+{
+ int ret;
+
+ ret = genphy_c45_read_link(phydev);
+ if (ret)
+ return ret;
+
+ phydev->speed = SPEED_UNKNOWN;
+ phydev->duplex = DUPLEX_UNKNOWN;
+ phydev->pause = 0;
+ phydev->asym_pause = 0;
+
+ if (phydev->autoneg == AUTONEG_ENABLE) {
+ ret = adin_read_lpa(phydev);
+ if (ret)
+ return ret;
+
+ phy_resolve_aneg_linkmode(phydev);
+ } else {
+ /* Only one mode & duplex supported */
+ linkmode_zero(phydev->lp_advertising);
+ phydev->speed = SPEED_10;
+ phydev->duplex = DUPLEX_FULL;
+ }
+
+ return ret;
+}
+
+static int adin_config_aneg(struct phy_device *phydev)
+{
+ struct adin_priv *priv = phydev->priv;
+ int ret;
+
+ /* No sense to continue if auto-neg is disabled,
+ * only one link-mode supported.
+ */
+ if (phydev->autoneg == AUTONEG_DISABLE)
+ return 0;
+
+ if (priv->tx_level_24v)
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_AN,
+ ADIN_AN_ADV_ABILITY_H,
+ ADIN_AN_ADV_B10L_TX_LVL_HI_ABL |
+ ADIN_AN_ADV_B10L_TX_LVL_HI_REQ);
+ else
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_AN,
+ ADIN_AN_ADV_ABILITY_H,
+ ADIN_AN_ADV_B10L_TX_LVL_HI_ABL |
+ ADIN_AN_ADV_B10L_TX_LVL_HI_REQ);
+
+ if (ret < 0)
+ return ret;
+
+ return phy_set_bits_mmd(phydev, MDIO_MMD_AN, ADIN_AN_CONTROL, ADIN_AN_RESTART);
+}
+
+static void adin_link_change_notify(struct phy_device *phydev)
+{
+ bool tx_level_24v;
+ bool lp_tx_level_24v;
+ int val, mask;
+
+ if (phydev->state != PHY_RUNNING || phydev->autoneg == AUTONEG_DISABLE)
+ return;
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_LP_ADV_ABILITY_H);
+ if (val < 0)
+ return;
+
+ mask = ADIN_AN_LP_ADV_B10L_TX_LVL_HI_ABL | ADIN_AN_LP_ADV_B10L_TX_LVL_HI_REQ;
+ lp_tx_level_24v = (val & mask) == mask;
+
+ val = phy_read_mmd(phydev, MDIO_MMD_AN, ADIN_AN_ADV_ABILITY_H);
+ if (val < 0)
+ return;
+
+ mask = ADIN_AN_ADV_B10L_TX_LVL_HI_ABL | ADIN_AN_ADV_B10L_TX_LVL_HI_REQ;
+ tx_level_24v = (val & mask) == mask;
+
+ if (tx_level_24v && lp_tx_level_24v)
+ phydev_info(phydev, "Negotiated 2.4V TX level\n");
+ else
+ phydev_info(phydev, "Negotiated 1.0V TX level\n");
+}
+
+static int adin_set_powerdown_mode(struct phy_device *phydev, bool en)
+{
+ int ret, timeout;
+ u16 val;
+
+ if (en)
+ val = ADIN_CRSM_SFT_PD_CNTRL_EN;
+ else
+ val = 0;
+
+ ret = phy_write_mmd(phydev, MDIO_MMD_VEND1,
+ ADIN_CRSM_SFT_PD_CNTRL, val);
+ if (ret < 0)
+ return ret;
+
+ timeout = 30;
+ while (timeout-- > 0) {
+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND1,
+ ADIN_CRSM_STAT);
+ if (ret < 0)
+ return ret;
+
+ if ((ret & ADIN_CRSM_SFT_PD_RDY) == val)
+ return 0;
+
+ mdelay(1);
+ }
+
+ return -ETIMEDOUT;
+}
+
+static int adin_suspend(struct phy_device *phydev)
+{
+ return adin_set_powerdown_mode(phydev, true);
+}
+
+static int adin_resume(struct phy_device *phydev)
+{
+ return adin_set_powerdown_mode(phydev, false);
+}
+
+static int adin_set_loopback(struct phy_device *phydev, bool enable)
+{
+ int ret;
+
+ if (enable)
+ return phy_set_bits_mmd(phydev, MDIO_MMD_PCS,
+ ADIN_B10L_PCS_CNTRL,
+ ADIN_PCS_CNTRL_B10L_LB_PCS_EN);
+
+ /* MAC interface block loopback */
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_VEND1, ADIN_MAC_IF_LOOPBACK,
+ ADIN_MAC_IF_LOOPBACK_EN |
+ ADIN_MAC_IF_REMOTE_LOOPBACK_EN);
+ if (ret < 0)
+ return ret;
+
+ /* PCS loopback (according to 10BASE-T1L spec) */
+ ret = phy_clear_bits_mmd(phydev, MDIO_MMD_PCS, ADIN_B10L_PCS_CNTRL,
+ ADIN_PCS_CNTRL_B10L_LB_PCS_EN);
+ if (ret < 0)
+ return ret;
+
+ /* PMA loopback (according to 10BASE-T1L spec) */
+ return phy_clear_bits_mmd(phydev, MDIO_MMD_PMAPMD, ADIN_B10L_PMA_CNTRL,
+ ADIN_PMA_CNTRL_B10L_LB_PMA_LOC_EN);
+}
+
+static int adin_config_init(struct phy_device *phydev)
+{
+ struct adin_priv *priv = phydev->priv;
+ struct device *dev = &phydev->mdio.dev;
+ int ret;
+
+ ret = phy_read_mmd(phydev, MDIO_MMD_PMAPMD, ADIN_B10L_PMA_STAT);
+ if (ret < 0)
+ return ret;
+
+ /* This depends on the voltage level from the power source */
+ priv->tx_level_24v = !!(ret & ADIN_PMA_STAT_B10L_TX_LVL_HI_ABLE);
+
+ phydev_dbg(phydev, "PHY supports 2.4V TX level: %s\n",
+ priv->tx_level_24v ? "yes" : "no");
+
+ if (priv->tx_level_24v &&
+ device_property_present(dev, "adi,disable-2-4-v-tx-level")) {
+ phydev_info(phydev,
+ "PHY supports 2.4V TX level, but disabled via config\n");
+ priv->tx_level_24v = 0;
+ }
+
+ return 0;
+}
+
+static int adin_soft_reset(struct phy_device *phydev)
+{
+ int timeout;
+ int ret;
+
+ ret = phy_set_bits_mmd(phydev, MDIO_MMD_VEND1, ADIN_CRSM_SFT_RST, ADIN_CRSM_SFT_RST_EN);
+ if (ret < 0)
+ return ret;
+
+ timeout = 30;
+ while (timeout >= 0) {
+ ret = phy_read_mmd(phydev, MDIO_MMD_VEND1, ADIN_CRSM_STAT);
+ if (ret < 0)
+ return ret;
+
+ if (ret & ADIN_CRSM_SYS_RDY)
+ return 0;
+
+ usleep_range(10000, 15000);
+ timeout -= 10;
+ }
+
+ return -ETIMEDOUT;
+}
+
+static int adin_get_features(struct phy_device *phydev)
+{
+ linkmode_set_bit_array(phy_basic_ports_array, ARRAY_SIZE(phy_basic_ports_array),
+ phydev->supported);
+
+ linkmode_set_bit_array(phy_10_features_array, ARRAY_SIZE(phy_10_features_array),
+ phydev->supported);
+
+ return 0;
+}
+
+static int adin_probe(struct phy_device *phydev)
+{
+ struct device *dev = &phydev->mdio.dev;
+ struct adin_priv *priv;
+
+ priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
+ if (!priv)
+ return -ENOMEM;
+
+ phydev->priv = priv;
+
+ return 0;
+}
+
+static struct phy_driver adin_driver[] = {
+ {
+ PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100),
+ .name = "ADIN1100",
+ .get_features = adin_get_features,
+ .match_phy_device = adin_match_phy_device,
+ .soft_reset = adin_soft_reset,
+ .probe = adin_probe,
+ .config_init = adin_config_init,
+ .config_aneg = adin_config_aneg,
+ .link_change_notify = adin_link_change_notify,
+ .read_status = adin_read_status,
+ .set_loopback = adin_set_loopback,
+ .suspend = adin_suspend,
+ .resume = adin_resume,
+ },
+};
+
+module_phy_driver(adin_driver);
+
+static struct mdio_device_id __maybe_unused adin_tbl[] = {
+ { PHY_ID_MATCH_MODEL(PHY_ID_ADIN1100) },
+ { }
+};
+
+MODULE_DEVICE_TABLE(mdio, adin_tbl);
+MODULE_DESCRIPTION("Analog Devices Industrial Ethernet T1L PHY driver");
+MODULE_LICENSE("Dual BSD/GPL");