deleted file mode 100644
@@ -1,212 +0,0 @@
-// SPDX-License-Identifier: GPL-2.0-only OR BSD-3-Clause
-
-/* Initialize and handle GPIO interrupt triggered by INT_N PHY signal.
- * This GPIO interrupt triggers the PHY state machine to bring the link
- * up/down.
- *
- * Copyright (C) 2021 NVIDIA CORPORATION & AFFILIATES
- */
-
-#include <linux/acpi.h>
-#include <linux/bitfield.h>
-#include <linux/device.h>
-#include <linux/err.h>
-#include <linux/gpio/driver.h>
-#include <linux/interrupt.h>
-#include <linux/io.h>
-#include <linux/irq.h>
-#include <linux/irqdomain.h>
-#include <linux/irqreturn.h>
-#include <linux/platform_device.h>
-#include <linux/property.h>
-
-#include "mlxbf_gige.h"
-#include "mlxbf_gige_regs.h"
-
-#define MLXBF_GIGE_GPIO_CAUSE_FALL_EN 0x48
-#define MLXBF_GIGE_GPIO_CAUSE_OR_CAUSE_EVTEN0 0x80
-#define MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0 0x94
-#define MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE 0x98
-
-static void mlxbf_gige_gpio_enable(struct mlxbf_gige *priv)
-{
- unsigned long flags;
- u32 val;
-
- spin_lock_irqsave(&priv->gpio_lock, flags);
- val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE);
- val |= priv->phy_int_gpio_mask;
- writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE);
-
- /* The INT_N interrupt level is active low.
- * So enable cause fall bit to detect when GPIO
- * state goes low.
- */
- val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_FALL_EN);
- val |= priv->phy_int_gpio_mask;
- writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_FALL_EN);
-
- /* Enable PHY interrupt by setting the priority level */
- val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0);
- val |= priv->phy_int_gpio_mask;
- writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0);
- spin_unlock_irqrestore(&priv->gpio_lock, flags);
-}
-
-static void mlxbf_gige_gpio_disable(struct mlxbf_gige *priv)
-{
- unsigned long flags;
- u32 val;
-
- spin_lock_irqsave(&priv->gpio_lock, flags);
- val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0);
- val &= ~priv->phy_int_gpio_mask;
- writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_EVTEN0);
- spin_unlock_irqrestore(&priv->gpio_lock, flags);
-}
-
-static irqreturn_t mlxbf_gige_gpio_handler(int irq, void *ptr)
-{
- struct mlxbf_gige *priv;
- u32 val;
-
- priv = ptr;
-
- /* Check if this interrupt is from PHY device.
- * Return if it is not.
- */
- val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CAUSE_EVTEN0);
- if (!(val & priv->phy_int_gpio_mask))
- return IRQ_NONE;
-
- /* Clear interrupt when done, otherwise, no further interrupt
- * will be triggered.
- */
- val = readl(priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE);
- val |= priv->phy_int_gpio_mask;
- writel(val, priv->gpio_io + MLXBF_GIGE_GPIO_CAUSE_OR_CLRCAUSE);
-
- generic_handle_irq(priv->phy_irq);
-
- return IRQ_HANDLED;
-}
-
-static void mlxbf_gige_gpio_mask(struct irq_data *irqd)
-{
- struct mlxbf_gige *priv = irq_data_get_irq_chip_data(irqd);
-
- mlxbf_gige_gpio_disable(priv);
-}
-
-static void mlxbf_gige_gpio_unmask(struct irq_data *irqd)
-{
- struct mlxbf_gige *priv = irq_data_get_irq_chip_data(irqd);
-
- mlxbf_gige_gpio_enable(priv);
-}
-
-static struct irq_chip mlxbf_gige_gpio_chip = {
- .name = "mlxbf_gige_phy",
- .irq_mask = mlxbf_gige_gpio_mask,
- .irq_unmask = mlxbf_gige_gpio_unmask,
-};
-
-static int mlxbf_gige_gpio_domain_map(struct irq_domain *d,
- unsigned int irq,
- irq_hw_number_t hwirq)
-{
- irq_set_chip_data(irq, d->host_data);
- irq_set_chip_and_handler(irq, &mlxbf_gige_gpio_chip, handle_simple_irq);
- irq_set_noprobe(irq);
-
- return 0;
-}
-
-static const struct irq_domain_ops mlxbf_gige_gpio_domain_ops = {
- .map = mlxbf_gige_gpio_domain_map,
- .xlate = irq_domain_xlate_twocell,
-};
-
-#ifdef CONFIG_ACPI
-static int mlxbf_gige_gpio_resources(struct acpi_resource *ares,
- void *data)
-{
- struct acpi_resource_gpio *gpio;
- u32 *phy_int_gpio = data;
-
- if (ares->type == ACPI_RESOURCE_TYPE_GPIO) {
- gpio = &ares->data.gpio;
- *phy_int_gpio = gpio->pin_table[0];
- }
-
- return 1;
-}
-#endif
-
-void mlxbf_gige_gpio_free(struct mlxbf_gige *priv)
-{
- irq_dispose_mapping(priv->phy_irq);
- irq_domain_remove(priv->irqdomain);
-}
-
-int mlxbf_gige_gpio_init(struct platform_device *pdev,
- struct mlxbf_gige *priv)
-{
- struct device *dev = &pdev->dev;
- struct resource *res;
- u32 phy_int_gpio = 0;
- int ret;
-
- LIST_HEAD(resources);
-
- res = platform_get_resource(pdev, IORESOURCE_MEM, MLXBF_GIGE_RES_GPIO0);
- if (!res)
- return -ENODEV;
-
- priv->gpio_io = devm_ioremap(dev, res->start, resource_size(res));
- if (!priv->gpio_io)
- return -ENOMEM;
-
-#ifdef CONFIG_ACPI
- ret = acpi_dev_get_resources(ACPI_COMPANION(dev),
- &resources, mlxbf_gige_gpio_resources,
- &phy_int_gpio);
- acpi_dev_free_resource_list(&resources);
- if (ret < 0 || !phy_int_gpio) {
- dev_err(dev, "Error retrieving the gpio phy pin");
- return -EINVAL;
- }
-#endif
-
- priv->phy_int_gpio_mask = BIT(phy_int_gpio);
-
- mlxbf_gige_gpio_disable(priv);
-
- priv->hw_phy_irq = platform_get_irq(pdev, MLXBF_GIGE_PHY_INT_N);
-
- priv->irqdomain = irq_domain_add_simple(NULL, 1, 0,
- &mlxbf_gige_gpio_domain_ops,
- priv);
- if (!priv->irqdomain) {
- dev_err(dev, "Failed to add IRQ domain\n");
- return -ENOMEM;
- }
-
- priv->phy_irq = irq_create_mapping(priv->irqdomain, 0);
- if (!priv->phy_irq) {
- irq_domain_remove(priv->irqdomain);
- priv->irqdomain = NULL;
- dev_err(dev, "Error mapping PHY IRQ\n");
- return -EINVAL;
- }
-
- ret = devm_request_irq(dev, priv->hw_phy_irq, mlxbf_gige_gpio_handler,
- IRQF_ONESHOT | IRQF_SHARED, "mlxbf_gige_phy", priv);
- if (ret) {
- dev_err(dev, "Failed to request PHY IRQ");
- mlxbf_gige_gpio_free(priv);
- return ret;
- }
-
- return ret;
-}
Since GPIO driver supports interrupt handling, replace custom routine with simple IRQ request. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> --- .../mellanox/mlxbf_gige/mlxbf_gige_gpio.c | 212 ------------------ 1 file changed, 212 deletions(-) delete mode 100644 drivers/net/ethernet/mellanox/mlxbf_gige/mlxbf_gige_gpio.c