@@ -888,68 +888,6 @@ qca8k_setup_mdio_bus(struct qca8k_priv *priv)
return 0;
}
-static int
-qca8k_setup_of_rgmii_delay(struct qca8k_priv *priv)
-{
- struct device_node *port_dn;
- phy_interface_t mode;
- struct dsa_port *dp;
- u32 val;
-
- /* CPU port is already checked */
- dp = dsa_to_port(priv->ds, 0);
-
- port_dn = dp->dn;
-
- /* Check if port 0 is set to the correct type */
- of_get_phy_mode(port_dn, &mode);
- if (mode != PHY_INTERFACE_MODE_RGMII_ID &&
- mode != PHY_INTERFACE_MODE_RGMII_RXID &&
- mode != PHY_INTERFACE_MODE_RGMII_TXID) {
- return 0;
- }
-
- switch (mode) {
- case PHY_INTERFACE_MODE_RGMII_ID:
- case PHY_INTERFACE_MODE_RGMII_RXID:
- if (of_property_read_u32(port_dn, "rx-internal-delay-ps", &val))
- val = 2;
- else
- /* Switch regs accept value in ns, convert ps to ns */
- val = val / 1000;
-
- if (val > QCA8K_MAX_DELAY) {
- dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value");
- val = 3;
- }
-
- priv->rgmii_rx_delay = val;
- /* Stop here if we need to check only for rx delay */
- if (mode != PHY_INTERFACE_MODE_RGMII_ID)
- break;
-
- fallthrough;
- case PHY_INTERFACE_MODE_RGMII_TXID:
- if (of_property_read_u32(port_dn, "tx-internal-delay-ps", &val))
- val = 1;
- else
- /* Switch regs accept value in ns, convert ps to ns */
- val = val / 1000;
-
- if (val > QCA8K_MAX_DELAY) {
- dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value");
- val = 3;
- }
-
- priv->rgmii_tx_delay = val;
- break;
- default:
- return 0;
- }
-
- return 0;
-}
-
static int
qca8k_setup_mac_pwr_sel(struct qca8k_priv *priv)
{
@@ -1026,10 +964,6 @@ qca8k_setup(struct dsa_switch *ds)
if (ret)
return ret;
- ret = qca8k_setup_of_rgmii_delay(priv);
- if (ret)
- return ret;
-
ret = qca8k_setup_mac_pwr_sel(priv);
if (ret)
return ret;
@@ -1201,7 +1135,8 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
const struct phylink_link_state *state)
{
struct qca8k_priv *priv = ds->priv;
- u32 reg, val;
+ struct dsa_port *dp;
+ u32 reg, val, delay;
int ret;
switch (port) {
@@ -1252,17 +1187,50 @@ qca8k_phylink_mac_config(struct dsa_switch *ds, int port, unsigned int mode,
case PHY_INTERFACE_MODE_RGMII_ID:
case PHY_INTERFACE_MODE_RGMII_TXID:
case PHY_INTERFACE_MODE_RGMII_RXID:
- /* RGMII_ID needs internal delay. This is enabled through
- * PORT5_PAD_CTRL for all ports, rather than individual port
- * registers
+ dp = dsa_to_port(ds, port);
+ val = QCA8K_PORT_PAD_RGMII_EN;
+
+ if (state->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ state->interface == PHY_INTERFACE_MODE_RGMII_TXID) {
+ if (of_property_read_u32(dp->dn, "tx-internal-delay-ps", &delay))
+ delay = 1;
+ else
+ /* Switch regs accept value in ns, convert ps to ns */
+ delay = delay / 1000;
+
+ if (delay > QCA8K_MAX_DELAY) {
+ dev_err(priv->dev, "rgmii tx delay is limited to a max value of 3ns, setting to the max value");
+ delay = 3;
+ }
+
+ val |= QCA8K_PORT_PAD_RGMII_TX_DELAY(delay) |
+ QCA8K_PORT_PAD_RGMII_TX_DELAY_EN;
+ }
+
+ if (state->interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ state->interface == PHY_INTERFACE_MODE_RGMII_RXID) {
+ if (of_property_read_u32(dp->dn, "rx-internal-delay-ps", &delay))
+ delay = 2;
+ else
+ /* Switch regs accept value in ns, convert ps to ns */
+ delay = delay / 1000;
+
+ if (delay > QCA8K_MAX_DELAY) {
+ dev_err(priv->dev, "rgmii rx delay is limited to a max value of 3ns, setting to the max value");
+ delay = 3;
+ }
+
+ val |= QCA8K_PORT_PAD_RGMII_RX_DELAY(delay) |
+ QCA8K_PORT_PAD_RGMII_RX_DELAY_EN;
+ }
+
+ /* Set RGMII delay based on the selected values */
+ qca8k_write(priv, reg, val);
+
+ /* QCA8337 requires to set rgmii rx delay for all ports.
+ * This is enabled through PORT5_PAD_CTRL for all ports,
+ * rather than individual port registers.
*/
- qca8k_write(priv, reg,
- QCA8K_PORT_PAD_RGMII_EN |
- QCA8K_PORT_PAD_RGMII_TX_DELAY(priv->rgmii_tx_delay) |
- QCA8K_PORT_PAD_RGMII_RX_DELAY(priv->rgmii_rx_delay) |
- QCA8K_PORT_PAD_RGMII_TX_DELAY_EN |
- QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
- /* QCA8337 requires to set rgmii rx delay */
if (priv->switch_id == QCA8K_ID_QCA8337)
qca8k_write(priv, QCA8K_REG_PORT5_PAD_CTRL,
QCA8K_PORT_PAD_RGMII_RX_DELAY_EN);
@@ -261,8 +261,6 @@ struct qca8k_match_data {
struct qca8k_priv {
u8 switch_id;
u8 switch_revision;
- u8 rgmii_tx_delay;
- u8 rgmii_rx_delay;
bool legacy_phy_port_mapping;
struct regmap *regmap;
struct mii_bus *bus;
Future proof commit. This switch have 2 CPU port and one valid configuration is first CPU port set to sgmii and second CPU port set to regmii-id. The current implementation detects delay only for CPU port zero set to rgmii and doesn't count any delay set in a secondary CPU port. Drop the current delay scan function and move it to the phylink mac_config to generilize and implicitly add support for secondary CPU port set to rgmii-id. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- drivers/net/dsa/qca8k.c | 122 +++++++++++++++------------------------- drivers/net/dsa/qca8k.h | 2 - 2 files changed, 45 insertions(+), 79 deletions(-)