@@ -87,6 +87,8 @@
#define AT803X_PSSR_MR_AN_COMPLETE 0x0200
#define AT803X_DEBUG_REG_0 0x00
+#define QCA8327_DEBUG_MANU_CTRL_EN BIT(2)
+#define QCA8337_DEBUG_MANU_CTRL_EN GENMASK(3, 2)
#define AT803X_DEBUG_RX_CLK_DLY_EN BIT(15)
#define AT803X_DEBUG_REG_5 0x05
@@ -1314,9 +1316,37 @@ static int qca83xx_config_init(struct phy_device *phydev)
break;
}
+ /* QCA8327 require DAC amplitude adjustment for 100m set to +6%.
+ * Disable on init and enable only with 100m speed following
+ * qca original source code.
+ */
+ if (phydev->drv->phy_id == QCA8327_A_PHY_ID ||
+ phydev->drv->phy_id == QCA8327_B_PHY_ID)
+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
+ QCA8327_DEBUG_MANU_CTRL_EN, 0);
+
return 0;
}
+static void qca83xx_link_change_notify(struct phy_device *phydev)
+{
+ /* QCA8337 doesn't require DAC Amplitude adjustement */
+ if (phydev->drv->phy_id == QCA8337_PHY_ID)
+ return;
+
+ /* Set DAC Amplitude adjustment to +6% for 100m on link running */
+ if (phydev->state == PHY_RUNNING) {
+ if (phydev->speed == SPEED_100)
+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
+ QCA8327_DEBUG_MANU_CTRL_EN,
+ QCA8327_DEBUG_MANU_CTRL_EN);
+ } else {
+ /* Reset DAC Amplitude adjustment */
+ at803x_debug_reg_mask(phydev, AT803X_DEBUG_REG_0,
+ QCA8327_DEBUG_MANU_CTRL_EN, 0);
+ }
+}
+
static int qca83xx_resume(struct phy_device *phydev)
{
int ret, val;
@@ -1471,6 +1501,7 @@ static struct phy_driver at803x_driver[] = {
.phy_id_mask = QCA8K_PHY_ID_MASK,
.name = "Qualcomm Atheros 8337 internal PHY",
/* PHY_GBIT_FEATURES */
+ .link_change_notify = qca83xx_link_change_notify,
.probe = at803x_probe,
.flags = PHY_IS_INTERNAL,
.config_init = qca83xx_config_init,
@@ -1486,6 +1517,7 @@ static struct phy_driver at803x_driver[] = {
.phy_id_mask = QCA8K_PHY_ID_MASK,
.name = "Qualcomm Atheros 8327-A internal PHY",
/* PHY_GBIT_FEATURES */
+ .link_change_notify = qca83xx_link_change_notify,
.probe = at803x_probe,
.flags = PHY_IS_INTERNAL,
.config_init = qca83xx_config_init,
@@ -1501,6 +1533,7 @@ static struct phy_driver at803x_driver[] = {
.phy_id_mask = QCA8K_PHY_ID_MASK,
.name = "Qualcomm Atheros 8327-B internal PHY",
/* PHY_GBIT_FEATURES */
+ .link_change_notify = qca83xx_link_change_notify,
.probe = at803x_probe,
.flags = PHY_IS_INTERNAL,
.config_init = qca83xx_config_init,
QCA8327 internal phy require DAC amplitude adjustement set to +6% with 100m speed. Also add additional define to report a change of the same reg in QCA8337. (different scope it does set 1000m voltage) Add link_change_notify function to set the proper amplitude adjustement on PHY_RUNNING state and disable on any other state. Fixes: b4df02b562f4 ("net: phy: at803x: add support for qca 8327 A variant internal phy") Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> --- drivers/net/phy/at803x.c | 33 +++++++++++++++++++++++++++++++++ 1 file changed, 33 insertions(+)