@@ -51,6 +51,8 @@
#define AT803X_INTR_ENABLE_PAGE_RECEIVED BIT(12)
#define AT803X_INTR_ENABLE_LINK_FAIL BIT(11)
#define AT803X_INTR_ENABLE_LINK_SUCCESS BIT(10)
+#define AT803X_INTR_ENABLE_LINK_FAIL_BX BIT(8)
+#define AT803X_INTR_ENABLE_LINK_SUCCESS_BX BIT(7)
#define AT803X_INTR_ENABLE_WIRESPEED_DOWNGRADE BIT(5)
#define AT803X_INTR_ENABLE_POLARITY_CHANGED BIT(1)
#define AT803X_INTR_ENABLE_WOL BIT(0)
@@ -85,7 +87,17 @@
#define AT803X_DEBUG_DATA 0x1E
#define AT803X_MODE_CFG_MASK 0x0F
-#define AT803X_MODE_CFG_SGMII 0x01
+#define AT803X_MODE_CFG_BASET_RGMII 0x00
+#define AT803X_MODE_CFG_BASET_SGMII 0x01
+#define AT803X_MODE_CFG_BX1000_RGMII_50 0x02
+#define AT803X_MODE_CFG_BX1000_RGMII_75 0x03
+#define AT803X_MODE_CFG_BX1000_CONV_50 0x04
+#define AT803X_MODE_CFG_BX1000_CONV_75 0x05
+#define AT803X_MODE_CFG_FX100_RGMII_50 0x06
+#define AT803X_MODE_CFG_FX100_CONV_50 0x07
+#define AT803X_MODE_CFG_RGMII_AUTO_MDET 0x0B
+#define AT803X_MODE_CFG_FX100_RGMII_75 0x0E
+#define AT803X_MODE_CFG_FX100_CONV_75 0x0F
#define AT803X_PSSR 0x11 /*PHY-Specific Status Register*/
#define AT803X_PSSR_MR_AN_COMPLETE 0x0200
@@ -283,6 +295,8 @@ struct at803x_priv {
u16 clk_25m_mask;
u8 smarteee_lpi_tw_1g;
u8 smarteee_lpi_tw_100m;
+ bool is_fiber;
+ bool is_1000basex;
struct regulator_dev *vddio_rdev;
struct regulator_dev *vddh_rdev;
struct regulator *vddio;
@@ -784,7 +798,33 @@ static int at803x_probe(struct phy_device *phydev)
return ret;
}
+ if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+ int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
+ int mode_cfg;
+
+ if (ccr < 0)
+ goto err;
+ mode_cfg = ccr & AT803X_MODE_CFG_MASK;
+
+ switch (mode_cfg) {
+ case AT803X_MODE_CFG_BX1000_RGMII_50:
+ case AT803X_MODE_CFG_BX1000_RGMII_75:
+ priv->is_1000basex = true;
+ fallthrough;
+ case AT803X_MODE_CFG_FX100_RGMII_50:
+ case AT803X_MODE_CFG_FX100_RGMII_75:
+ priv->is_fiber = true;
+ break;
+ }
+ }
+
return 0;
+
+err:
+ if (priv->vddio)
+ regulator_disable(priv->vddio);
+
+ return ret;
}
static void at803x_remove(struct phy_device *phydev)
@@ -797,6 +837,7 @@ static void at803x_remove(struct phy_device *phydev)
static int at803x_get_features(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int err;
err = genphy_read_abilities(phydev);
@@ -823,12 +864,13 @@ static int at803x_get_features(struct phy_device *phydev)
* As a result of that, ESTATUS_1000_XFULL is set
* to 1 even when operating in copper TP mode.
*
- * Remove this mode from the supported link modes,
- * as this driver currently only supports copper
- * operation.
+ * Remove this mode from the supported link modes
+ * when not operating in 1000BaseX mode.
*/
- linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
- phydev->supported);
+ if (!priv->is_1000basex)
+ linkmode_clear_bit(ETHTOOL_LINK_MODE_1000baseX_Full_BIT,
+ phydev->supported);
+
return 0;
}
@@ -892,15 +934,18 @@ static int at8031_pll_config(struct phy_device *phydev)
static int at803x_config_init(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int ret;
if (phydev->drv->phy_id == ATH8031_PHY_ID) {
/* Some bootloaders leave the fiber page selected.
- * Switch to the copper page, as otherwise we read
- * the PHY capabilities from the fiber side.
+ * Switch to the appropriate page (fiber or copper), as otherwise we
+ * read the PHY capabilities from the wrong page.
*/
phy_lock_mdio_bus(phydev);
- ret = at803x_write_page(phydev, AT803X_PAGE_COPPER);
+ ret = at803x_write_page(phydev,
+ priv->is_fiber ? AT803X_PAGE_FIBER :
+ AT803X_PAGE_COPPER);
phy_unlock_mdio_bus(phydev);
if (ret)
return ret;
@@ -959,6 +1004,7 @@ static int at803x_ack_interrupt(struct phy_device *phydev)
static int at803x_config_intr(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int err;
int value;
@@ -975,6 +1021,10 @@ static int at803x_config_intr(struct phy_device *phydev)
value |= AT803X_INTR_ENABLE_DUPLEX_CHANGED;
value |= AT803X_INTR_ENABLE_LINK_FAIL;
value |= AT803X_INTR_ENABLE_LINK_SUCCESS;
+ if (priv->is_fiber) {
+ value |= AT803X_INTR_ENABLE_LINK_FAIL_BX;
+ value |= AT803X_INTR_ENABLE_LINK_SUCCESS_BX;
+ }
err = phy_write(phydev, AT803X_INTR_ENABLE, value);
} else {
@@ -1107,8 +1157,12 @@ static int at803x_read_specific_status(struct phy_device *phydev)
static int at803x_read_status(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int err, old_link = phydev->link;
+ if (priv->is_1000basex)
+ return genphy_c37_read_status(phydev);
+
/* Update the link, but return if there was an error */
err = genphy_update_link(phydev);
if (err)
@@ -1162,6 +1216,7 @@ static int at803x_config_mdix(struct phy_device *phydev, u8 ctrl)
static int at803x_config_aneg(struct phy_device *phydev)
{
+ struct at803x_priv *priv = phydev->priv;
int ret;
ret = at803x_config_mdix(phydev, phydev->mdix_ctrl);
@@ -1178,6 +1233,9 @@ static int at803x_config_aneg(struct phy_device *phydev)
return ret;
}
+ if (priv->is_1000basex)
+ return genphy_c37_config_aneg(phydev);
+
/* Do not restart auto-negotiation by setting ret to 0 defautly,
* when calling __genphy_config_aneg later.
*/
Previously this driver always forced the copper page to be selected, however for AR8031 in 100Base-FX or 1000Base-X modes, the fiber page needs to be selected. Set the appropriate mode based on the hardware mode_cfg strap selection. Enable the appropriate interrupt bits to detect fiber-side link up or down events. Update config_aneg and read_status methods to use the appropriate Clause 37 calls when fiber mode is in use. Signed-off-by: Robert Hancock <robert.hancock@calian.com> --- drivers/net/phy/at803x.c | 76 +++++++++++++++++++++++++++++++++++----- 1 file changed, 67 insertions(+), 9 deletions(-)