@@ -649,6 +649,28 @@ struct phy_device *phy_device_create(struct mii_bus *bus, int addr, u32 phy_id,
}
EXPORT_SYMBOL(phy_device_create);
+static int mdiobus_probe_mmd_read(struct mii_bus *bus, int prtad, int devad,
+ u16 regnum)
+{
+ int ret;
+
+ if (bus->probe_capabilities >= MDIOBUS_C45)
+ return mdiobus_c45_read(bus, prtad, devad, regnum);
+
+ mutex_lock(&bus->mdio_lock);
+
+ ret = __phy_mmd_indirect(bus, prtad, devad, regnum);
+ if (ret)
+ goto out;
+
+ ret = __mdiobus_read(bus, prtad, MII_MMD_DATA);
+
+out:
+ mutex_unlock(&bus->mdio_lock);
+
+ return ret;
+}
+
/* phy_c45_probe_present - checks to see if a MMD is present in the package
* @bus: the target MII bus
* @prtad: PHY package address on the MII bus
@@ -664,7 +686,7 @@ static int phy_c45_probe_present(struct mii_bus *bus, int prtad, int devad)
{
int stat2;
- stat2 = mdiobus_c45_read(bus, prtad, devad, MDIO_STAT2);
+ stat2 = mdiobus_probe_mmd_read(bus, prtad, devad, MDIO_STAT2);
if (stat2 < 0)
return stat2;
@@ -687,12 +709,12 @@ static int get_phy_c45_devs_in_pkg(struct mii_bus *bus, int addr, int dev_addr,
{
int phy_reg;
- phy_reg = mdiobus_c45_read(bus, addr, dev_addr, MDIO_DEVS2);
+ phy_reg = mdiobus_probe_mmd_read(bus, addr, dev_addr, MDIO_DEVS2);
if (phy_reg < 0)
return -EIO;
*devices_in_package = phy_reg << 16;
- phy_reg = mdiobus_c45_read(bus, addr, dev_addr, MDIO_DEVS1);
+ phy_reg = mdiobus_probe_mmd_read(bus, addr, dev_addr, MDIO_DEVS1);
if (phy_reg < 0)
return -EIO;
*devices_in_package |= phy_reg;
@@ -776,12 +798,12 @@ static int get_phy_c45_ids(struct mii_bus *bus, int addr,
continue;
}
- phy_reg = mdiobus_c45_read(bus, addr, i, MII_PHYSID1);
+ phy_reg = mdiobus_probe_mmd_read(bus, addr, i, MII_PHYSID1);
if (phy_reg < 0)
return -EIO;
c45_ids->device_ids[i] = phy_reg << 16;
- phy_reg = mdiobus_c45_read(bus, addr, i, MII_PHYSID2);
+ phy_reg = mdiobus_probe_mmd_read(bus, addr, i, MII_PHYSID2);
if (phy_reg < 0)
return -EIO;
c45_ids->device_ids[i] |= phy_reg;
There are some PHYs, namely the Maxlinear GPY215, whose driver is explicitly supporting C45-over-C22 access. At least that was the intention. In practice, it cannot work because get_phy_c45_ids() will always issue c45 register accesses. There is another issue at hand: the Microchip LAN8814, which is a c22 only quad PHY, has issues with c45 accesses on the same bus and its address decoder will find a match in the middle of another c45 transaction. This will lead to spurious reads and writes. The reads will corrupt the c45 in flight. The write will lead to random writes to the LAN8814 registers. As a workaround for PHYs which support C45-over-C22 register accesses, we can make the MDIO bus c22-only. For both reasons, extend the register accesses in get_phy_c45_ids() to allow indirect accesses, indicated by the bus->probe_capabilities bits. The probe_capabilities can then be degraded by a device tree property, for example. Or it will just work when the MDIO driver is c22-only and set the capabilities accordingly. Signed-off-by: Michael Walle <michael@walle.cc> --- drivers/net/phy/phy_device.c | 32 +++++++++++++++++++++++++++----- 1 file changed, 27 insertions(+), 5 deletions(-)