@@ -11,7 +11,7 @@ TEST_PROGS += udpgso_bench.sh fib_rule_tests.sh msg_zerocopy.sh psock_snd.sh
TEST_PROGS += udpgro_bench.sh udpgro.sh test_vxlan_under_vrf.sh reuseport_addr_any.sh
TEST_PROGS += test_vxlan_fdb_changelink.sh so_txtime.sh ipv6_flowlabel.sh
TEST_PROGS += tcp_fastopen_backup_key.sh fcnal-test.sh l2tp.sh traceroute.sh
-TEST_PROGS += fin_ack_lat.sh fib_nexthop_multiprefix.sh fib_nexthops.sh
+TEST_PROGS += fin_ack_lat.sh fib_nexthop_multiprefix.sh fib_nexthops.sh fib_nexthop_nongw.sh
TEST_PROGS += altnames.sh icmp.sh icmp_redirect.sh ip6_gre_headroom.sh
TEST_PROGS += route_localnet.sh
TEST_PROGS += reuseaddr_ports_exhausted.sh
new file mode 100755
@@ -0,0 +1,119 @@
+#!/bin/bash
+# SPDX-License-Identifier: GPL-2.0
+#
+# ns: h1 | ns: h2
+# 192.168.0.1/24 |
+# eth0 |
+# | 192.168.1.1/32
+# veth0 <---|---> veth1
+# Validate source address selection for route without gateway
+
+PAUSE_ON_FAIL=no
+VERBOSE=0
+ret=0
+
+################################################################################
+# helpers
+
+log_test()
+{
+ local rc=$1
+ local expected=$2
+ local msg="$3"
+
+ if [ ${rc} -eq ${expected} ]; then
+ printf "TEST: %-60s [ OK ]\n" "${msg}"
+ nsuccess=$((nsuccess+1))
+ else
+ ret=1
+ nfail=$((nfail+1))
+ printf "TEST: %-60s [FAIL]\n" "${msg}"
+ if [ "${PAUSE_ON_FAIL}" = "yes" ]; then
+ echo
+ echo "hit enter to continue, 'q' to quit"
+ read a
+ [ "$a" = "q" ] && exit 1
+ fi
+ fi
+
+ [ "$VERBOSE" = "1" ] && echo
+}
+
+run_cmd()
+{
+ local cmd="$*"
+ local out
+ local rc
+
+ if [ "$VERBOSE" = "1" ]; then
+ echo "COMMAND: $cmd"
+ fi
+
+ out=$(eval $cmd 2>&1)
+ rc=$?
+ if [ "$VERBOSE" = "1" -a -n "$out" ]; then
+ echo "$out"
+ fi
+
+ [ "$VERBOSE" = "1" ] && echo
+
+ return $rc
+}
+
+################################################################################
+# config
+setup()
+{
+ ip netns add h1
+ ip -n h1 link set lo up
+ ip netns add h2
+ ip -n h2 link set lo up
+
+ # Add a fake eth0 to support an ip address
+ ip -n h1 link add name eth0 type dummy
+ ip -n h1 link set eth0 up
+ ip -n h1 address add 192.168.0.1/24 dev eth0
+
+ # Configure veths (same @mac, arp off)
+ ip -n h1 link add name veth0 type veth peer name veth1 netns h2
+ ip -n h1 link set veth0 up
+
+ ip -n h2 link set veth1 up
+
+ # Configure @IP in the peer netns
+ ip -n h2 address add 192.168.1.1/32 dev veth1
+ ip -n h2 route add default dev veth1
+
+ # Add a nexthop without @gw and use it in a route
+ ip -n h1 nexthop add id 1 dev veth0
+ ip -n h1 route add 192.168.1.1 nhid 1
+}
+
+cleanup()
+{
+ ip netns del h1 2>/dev/null
+ ip netns del h2 2>/dev/null
+}
+
+trap cleanup EXIT
+
+################################################################################
+# main
+
+while getopts :pv o
+do
+ case $o in
+ p) PAUSE_ON_FAIL=yes;;
+ v) VERBOSE=1;;
+ esac
+done
+
+cleanup
+setup
+
+run_cmd ip -netns h1 route get 192.168.1.1
+log_test $? 0 "nexthop: get route with nexthop without gw"
+run_cmd ip netns exec h1 ping -c1 192.168.1.1
+log_test $? 0 "nexthop: ping through nexthop without gw"
+
+exit $ret
This test implement the scenario described in the commit "ip: fix dflt addr selection for connected nexthop". The test configures a nexthop object with an output device only (no gateway address) and a route that uses this nexthop. The goal is to check if the kernel selects a valid source address. Link: https://lore.kernel.org/netdev/20220712095545.10947-1-nicolas.dichtel@6wind.com/ Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com> --- v2 -> v3: - add more details in the commit log v1 -> v2: - add linux-kselftest@vger.kernel.org - clean trailing whitespaces - add a 'trap' on exit - remove useless sleep - remove useless arp off / fixed mac settings tools/testing/selftests/net/Makefile | 2 +- .../selftests/net/fib_nexthop_nongw.sh | 119 ++++++++++++++++++ 2 files changed, 120 insertions(+), 1 deletion(-) create mode 100755 tools/testing/selftests/net/fib_nexthop_nongw.sh