@@ -261,13 +261,13 @@ ieee802154_check_concurrent_iface(struct ieee802154_sub_if_data *sdata,
if (nsdata != sdata && ieee802154_sdata_running(nsdata)) {
int ret;
- /* TODO currently we don't support multiple node types
- * we need to run skb_clone at rx path. Check if there
- * exist really an use case if we need to support
- * multiple node types at the same time.
+ /* TODO currently we don't support multiple node/coord
+ * types we need to run skb_clone at rx path. Check if
+ * there exist really an use case if we need to support
+ * multiple node/coord types at the same time.
*/
- if (sdata->wpan_dev.iftype == NL802154_IFTYPE_NODE &&
- nsdata->wpan_dev.iftype == NL802154_IFTYPE_NODE)
+ if (sdata->wpan_dev.iftype != NL802154_IFTYPE_MONITOR &&
+ nsdata->wpan_dev.iftype != NL802154_IFTYPE_MONITOR)
return -EBUSY;
/* check all phy mac sublayer settings are the same.
@@ -564,6 +564,7 @@ ieee802154_setup_sdata(struct ieee802154_sub_if_data *sdata,
wpan_dev->short_addr = cpu_to_le16(IEEE802154_ADDR_BROADCAST);
switch (type) {
+ case NL802154_IFTYPE_COORD:
case NL802154_IFTYPE_NODE:
ieee802154_be64_to_le64(&wpan_dev->extended_addr,
sdata->dev->dev_addr);
@@ -623,6 +624,7 @@ ieee802154_if_add(struct ieee802154_local *local, const char *name,
ieee802154_le64_to_be64(ndev->perm_addr,
&local->hw.phy->perm_extended_addr);
switch (type) {
+ case NL802154_IFTYPE_COORD:
case NL802154_IFTYPE_NODE:
ndev->type = ARPHRD_IEEE802154;
if (ieee802154_is_valid_extended_unicast_addr(extended_addr)) {
@@ -107,7 +107,7 @@ ieee802154_alloc_hw(size_t priv_data_len, const struct ieee802154_ops *ops)
phy->supported.lbt = NL802154_SUPPORTED_BOOL_FALSE;
/* always supported */
- phy->supported.iftypes = BIT(NL802154_IFTYPE_NODE);
+ phy->supported.iftypes = BIT(NL802154_IFTYPE_NODE) | BIT(NL802154_IFTYPE_COORD);
return &local->hw;
}
@@ -208,6 +208,7 @@ __ieee802154_rx_handle_packet(struct ieee802154_local *local,
int ret;
struct ieee802154_sub_if_data *sdata;
struct ieee802154_hdr hdr;
+ struct sk_buff *skb2;
ret = ieee802154_parse_frame_start(skb, &hdr);
if (ret) {
@@ -217,7 +218,7 @@ __ieee802154_rx_handle_packet(struct ieee802154_local *local,
}
list_for_each_entry_rcu(sdata, &local->interfaces, list) {
- if (sdata->wpan_dev.iftype != NL802154_IFTYPE_NODE)
+ if (sdata->wpan_dev.iftype == NL802154_IFTYPE_MONITOR)
continue;
if (!ieee802154_sdata_running(sdata))
@@ -230,9 +231,11 @@ __ieee802154_rx_handle_packet(struct ieee802154_local *local,
sdata->required_filtering == IEEE802154_FILTERING_4_FRAME_FIELDS)
continue;
- ieee802154_subif_frame(sdata, skb, &hdr);
- skb = NULL;
- break;
+ skb2 = skb_clone(skb, GFP_ATOMIC);
+ if (skb2) {
+ skb2->dev = sdata->dev;
+ ieee802154_subif_frame(sdata, skb2, &hdr);
+ }
}
}
As a first strep in introducing proper PAN management and association, we need to be able to create coordinator interfaces which might act as coordinator or PAN coordinator. Hence, let's add the minimum support to allow the creation of these interfaces. Even though the necessary logic to handle several interfaces on the same device is added to make this future move easier, in practice only several interfaces of type MONITOR are allowed at the same time. The other combinations are not allowed (interface creation is possible but only one can be opened at a time) because, with a single PHY featuring a single set of address filters, we cannot afford handling two distinct interfaces (with different address filters or filtering requirements): * Having 2 NODEs, 2 COORDs or 1 NODE + 1 COORD -> cannot work because the address filters would be different * Having 1 MONITOR + either 1 NODE or 1 COORD -> cannot work because the filtering levels are incompatible Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com> --- net/mac802154/iface.c | 14 ++++++++------ net/mac802154/main.c | 2 +- net/mac802154/rx.c | 11 +++++++---- 3 files changed, 16 insertions(+), 11 deletions(-)