| Message ID | 20230126213539.166298-2-andrey.konovalov@linaro.org (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | 54aa39a513dbf2164ca462a19f04519b2407a224 |
| Delegated to: | Netdev Maintainers |
| Headers | show |
| Series | net: stmmac: do not stop RX_CLK in Rx LPI state for qcs404 SoC | expand |
diff --git a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c index 835caa15d55f..732774645c1a 100644 --- a/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c +++ b/drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c @@ -560,6 +560,8 @@ static int qcom_ethqos_probe(struct platform_device *pdev) plat_dat->has_gmac4 = 1; plat_dat->pmt = 1; plat_dat->tso_en = of_property_read_bool(np, "snps,tso"); + if (of_device_is_compatible(np, "qcom,qcs404-ethqos")) + plat_dat->rx_clk_runs_in_lpi = 1; ret = stmmac_dvr_probe(&pdev->dev, plat_dat, &stmmac_res); if (ret) diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c index b7e5af58ab75..1a5b8dab5e9b 100644 --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c @@ -1080,7 +1080,8 @@ static void stmmac_mac_link_up(struct phylink_config *config, stmmac_mac_set(priv, priv->ioaddr, true); if (phy && priv->dma_cap.eee) { - priv->eee_active = phy_init_eee(phy, 1) >= 0; + priv->eee_active = + phy_init_eee(phy, !priv->plat->rx_clk_runs_in_lpi) >= 0; priv->eee_enabled = stmmac_eee_init(priv); priv->tx_lpi_enabled = priv->eee_enabled; stmmac_set_eee_pls(priv, priv->hw, true); diff --git a/include/linux/stmmac.h b/include/linux/stmmac.h index 83ca2e8eb6b5..a152678b82b7 100644 --- a/include/linux/stmmac.h +++ b/include/linux/stmmac.h @@ -252,6 +252,7 @@ struct plat_stmmacenet_data { int rss_en; int mac_port_sel_speed; bool en_tx_lpi_clockgating; + bool rx_clk_runs_in_lpi; int has_xgmac; bool vlan_fail_q_en; u8 vlan_fail_q;
Currently in phy_init_eee() the driver unconditionally configures the PHY to stop RX_CLK after entering Rx LPI state. This causes an LPI interrupt storm on my qcs404-base board. Change the PHY initialization so that for "qcom,qcs404-ethqos" compatible device RX_CLK continues to run even in Rx LPI state. Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org> --- drivers/net/ethernet/stmicro/stmmac/dwmac-qcom-ethqos.c | 2 ++ drivers/net/ethernet/stmicro/stmmac/stmmac_main.c | 3 ++- include/linux/stmmac.h | 1 + 3 files changed, 5 insertions(+), 1 deletion(-)