@@ -10,6 +10,7 @@
#include <linux/kernel.h>
#include <linux/module.h>
#include <linux/phy.h>
+#include <linux/of.h>
#define PHY_ID_YT8511 0x0000010a
#define PHY_ID_YT8521 0x0000011A
@@ -187,21 +188,9 @@
* 1b1 use inverted tx_clk_rgmii.
*/
#define YT8521_RC1R_TX_CLK_SEL_INVERTED BIT(14)
-/* TX Gig-E Delay is bits 3:0, default 0x1
- * TX Fast-E Delay is bits 7:4, default 0xf
- * RX Delay is bits 13:10, default 0x0
- * Delay = 150ps * N
- * On = 2250ps, off = 0ps
- */
#define YT8521_RC1R_RX_DELAY_MASK GENMASK(13, 10)
-#define YT8521_RC1R_RX_DELAY_EN (0xF << 10)
-#define YT8521_RC1R_RX_DELAY_DIS (0x0 << 10)
#define YT8521_RC1R_FE_TX_DELAY_MASK GENMASK(7, 4)
-#define YT8521_RC1R_FE_TX_DELAY_EN (0xF << 4)
-#define YT8521_RC1R_FE_TX_DELAY_DIS (0x0 << 4)
#define YT8521_RC1R_GE_TX_DELAY_MASK GENMASK(3, 0)
-#define YT8521_RC1R_GE_TX_DELAY_EN (0xF << 0)
-#define YT8521_RC1R_GE_TX_DELAY_DIS (0x0 << 0)
#define YT8521_RC1R_RGMII_0_000_NS 0
#define YT8521_RC1R_RGMII_0_150_NS 1
#define YT8521_RC1R_RGMII_0_300_NS 2
@@ -274,6 +263,10 @@
/* Extended Register end */
+#define YTPHY_DTS_OUTPUT_CLK_DIS 0
+#define YTPHY_DTS_OUTPUT_CLK_25M 25000000
+#define YTPHY_DTS_OUTPUT_CLK_125M 125000000
+
struct yt8521_priv {
/* combo_advertising is used for case of YT8521 in combo mode,
* this means that yt8521 may work in utp or fiber mode which depends
@@ -640,6 +633,142 @@ static int yt8521_write_page(struct phy_device *phydev, int page)
return ytphy_modify_ext(phydev, YT8521_REG_SPACE_SELECT_REG, mask, set);
};
+/**
+ * struct ytphy_cfg_reg_map - map a config value to a register value
+ * @cfg: value in device configuration
+ * @reg: value in the register
+ */
+struct ytphy_cfg_reg_map {
+ u32 cfg;
+ u32 reg;
+};
+
+static const struct ytphy_cfg_reg_map ytphy_rgmii_delays[] = {
+ /* for tx delay / rx delay with YT8521_CCR_RXC_DLY_EN is not set. */
+ { 0, YT8521_RC1R_RGMII_0_000_NS },
+ { 150, YT8521_RC1R_RGMII_0_150_NS }, /* default tx delay */
+ { 300, YT8521_RC1R_RGMII_0_300_NS },
+ { 450, YT8521_RC1R_RGMII_0_450_NS },
+ { 600, YT8521_RC1R_RGMII_0_600_NS },
+ { 750, YT8521_RC1R_RGMII_0_750_NS },
+ { 900, YT8521_RC1R_RGMII_0_900_NS },
+ { 1050, YT8521_RC1R_RGMII_1_050_NS },
+ { 1200, YT8521_RC1R_RGMII_1_200_NS },
+ { 1350, YT8521_RC1R_RGMII_1_350_NS },
+ { 1500, YT8521_RC1R_RGMII_1_500_NS },
+ { 1650, YT8521_RC1R_RGMII_1_650_NS },
+ { 1800, YT8521_RC1R_RGMII_1_800_NS },
+ { 1950, YT8521_RC1R_RGMII_1_950_NS }, /* default rx delay */
+ { 2100, YT8521_RC1R_RGMII_2_100_NS },
+ { 2250, YT8521_RC1R_RGMII_2_250_NS },
+
+ /* only for rx delay with YT8521_CCR_RXC_DLY_EN is set. */
+ { 0 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_000_NS },
+ { 150 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_150_NS },
+ { 300 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_300_NS },
+ { 450 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_450_NS },
+ { 600 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_600_NS },
+ { 750 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_750_NS },
+ { 900 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_0_900_NS },
+ { 1050 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_050_NS },
+ { 1200 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_200_NS },
+ { 1350 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_350_NS },
+ { 1500 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_500_NS },
+ { 1650 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_650_NS },
+ { 1800 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_800_NS },
+ { 1950 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_1_950_NS },
+ { 2100 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_2_100_NS },
+ { 2250 + YT8521_CCR_RXC_DLY_1_900_NS, YT8521_RC1R_RGMII_2_250_NS }
+};
+
+static u32 ytphy_get_delay_reg_value(struct phy_device *phydev,
+ const char *prop_name,
+ const struct ytphy_cfg_reg_map *tbl,
+ int tb_size,
+ u16 *rxc_dly_en,
+ u32 dflt)
+{
+ struct device_node *node = phydev->mdio.dev.of_node;
+ int tb_size_half = tb_size / 2;
+ u32 val;
+ int i;
+
+ if (of_property_read_u32(node, prop_name, &val))
+ goto err_dts_val;
+
+ /* when rxc_dly_en is NULL, it is get the delay for tx, only half of
+ * tb_size is valid.
+ */
+ if (!rxc_dly_en)
+ tb_size = tb_size_half;
+
+ for (i = 0; i < tb_size; i++) {
+ if (tbl[i].cfg == val) {
+ if (rxc_dly_en && i < tb_size_half)
+ *rxc_dly_en = 0;
+ return tbl[i].reg;
+ }
+ }
+
+ phydev_warn(phydev, "Unsupported value %d for %s using default (%u)\n",
+ val, prop_name, dflt);
+
+err_dts_val:
+ /* when rxc_dly_en is not NULL, it is get the delay for rx.
+ * The rx default in dts and ytphy_rgmii_clk_delay_config is 1950 ps,
+ * so YT8521_CCR_RXC_DLY_EN should not be set.
+ */
+ if (rxc_dly_en)
+ *rxc_dly_en = 0;
+
+ return dflt;
+}
+
+static int ytphy_rgmii_clk_delay_config(struct phy_device *phydev)
+{
+ int tb_size = ARRAY_SIZE(ytphy_rgmii_delays);
+ u16 rxc_dly_en = YT8521_CCR_RXC_DLY_EN;
+ u32 rx_reg, tx_reg;
+ u16 mask, val = 0;
+ int ret;
+
+ rx_reg = ytphy_get_delay_reg_value(phydev, "rx-internal-delay-ps",
+ ytphy_rgmii_delays, tb_size,
+ &rxc_dly_en,
+ YT8521_RC1R_RGMII_1_950_NS);
+ tx_reg = ytphy_get_delay_reg_value(phydev, "tx-internal-delay-ps",
+ ytphy_rgmii_delays, tb_size, NULL,
+ YT8521_RC1R_RGMII_0_150_NS);
+
+ switch (phydev->interface) {
+ case PHY_INTERFACE_MODE_RGMII:
+ rxc_dly_en = 0;
+ break;
+ case PHY_INTERFACE_MODE_RGMII_RXID:
+ val |= FIELD_PREP(YT8521_RC1R_RX_DELAY_MASK, rx_reg);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_TXID:
+ rxc_dly_en = 0;
+ val |= FIELD_PREP(YT8521_RC1R_GE_TX_DELAY_MASK, tx_reg);
+ break;
+ case PHY_INTERFACE_MODE_RGMII_ID:
+ val |= FIELD_PREP(YT8521_RC1R_RX_DELAY_MASK, rx_reg) |
+ FIELD_PREP(YT8521_RC1R_GE_TX_DELAY_MASK, tx_reg);
+ break;
+ default: /* do not support other modes */
+ return -EOPNOTSUPP;
+ }
+
+ ret = ytphy_modify_ext(phydev, YT8521_CHIP_CONFIG_REG,
+ YT8521_CCR_RXC_DLY_EN, rxc_dly_en);
+ if (ret < 0)
+ return ret;
+
+ /* Generally, it is not necessary to adjust YT8521_RC1R_FE_TX_DELAY */
+ mask = YT8521_RC1R_RX_DELAY_MASK | YT8521_RC1R_GE_TX_DELAY_MASK;
+ return ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG, mask, val);
+}
+
/**
* yt8521_probe() - read chip config then set suitable polling_mode
* @phydev: a pointer to a &struct phy_device
@@ -648,9 +777,12 @@ static int yt8521_write_page(struct phy_device *phydev, int page)
*/
static int yt8521_probe(struct phy_device *phydev)
{
+ struct device_node *node = phydev->mdio.dev.of_node;
struct device *dev = &phydev->mdio.dev;
struct yt8521_priv *priv;
int chip_config;
+ u16 mask, val;
+ u32 freq;
int ret;
priv = devm_kzalloc(dev, sizeof(*priv), GFP_KERNEL);
@@ -695,7 +827,45 @@ static int yt8521_probe(struct phy_device *phydev)
return ret;
}
- return 0;
+ if (of_property_read_u32(node, "motorcomm,clk-out-frequency-hz", &freq))
+ freq = YTPHY_DTS_OUTPUT_CLK_DIS;
+
+ if (phydev->drv->phy_id == PHY_ID_YT8521) {
+ switch (freq) {
+ case YTPHY_DTS_OUTPUT_CLK_DIS:
+ mask = YT8521_SCR_SYNCE_ENABLE;
+ val = 0;
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_25M:
+ mask = YT8521_SCR_SYNCE_ENABLE |
+ YT8521_SCR_CLK_SRC_MASK |
+ YT8521_SCR_CLK_FRE_SEL_125M;
+ val = YT8521_SCR_SYNCE_ENABLE |
+ FIELD_PREP(YT8521_SCR_CLK_SRC_MASK,
+ YT8521_SCR_CLK_SRC_REF_25M);
+ break;
+ case YTPHY_DTS_OUTPUT_CLK_125M:
+ mask = YT8521_SCR_SYNCE_ENABLE |
+ YT8521_SCR_CLK_SRC_MASK |
+ YT8521_SCR_CLK_FRE_SEL_125M;
+ val = YT8521_SCR_SYNCE_ENABLE |
+ YT8521_SCR_CLK_FRE_SEL_125M |
+ FIELD_PREP(YT8521_SCR_CLK_SRC_MASK,
+ YT8521_SCR_CLK_SRC_PLL_125M);
+ break;
+ default:
+ phydev_warn(phydev, "Freq err:%u\n", freq);
+ return -EINVAL;
+ }
+ } else if (phydev->drv->phy_id == PHY_ID_YT8531S) {
+ return 0;
+ } else {
+ phydev_warn(phydev, "PHY id err\n");
+ return -EINVAL;
+ }
+
+ return ytphy_modify_ext_with_lock(phydev, YTPHY_SYNCE_CFG_REG, mask,
+ val);
}
/**
@@ -1180,61 +1350,36 @@ static int yt8521_resume(struct phy_device *phydev)
*/
static int yt8521_config_init(struct phy_device *phydev)
{
+ struct device_node *node = phydev->mdio.dev.of_node;
int old_page;
int ret = 0;
- u16 val;
old_page = phy_select_page(phydev, YT8521_RSSR_UTP_SPACE);
if (old_page < 0)
goto err_restore_page;
- switch (phydev->interface) {
- case PHY_INTERFACE_MODE_RGMII:
- val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_FE_TX_DELAY_DIS;
- val |= YT8521_RC1R_RX_DELAY_DIS;
- break;
- case PHY_INTERFACE_MODE_RGMII_RXID:
- val = YT8521_RC1R_GE_TX_DELAY_DIS | YT8521_RC1R_FE_TX_DELAY_DIS;
- val |= YT8521_RC1R_RX_DELAY_EN;
- break;
- case PHY_INTERFACE_MODE_RGMII_TXID:
- val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_FE_TX_DELAY_EN;
- val |= YT8521_RC1R_RX_DELAY_DIS;
- break;
- case PHY_INTERFACE_MODE_RGMII_ID:
- val = YT8521_RC1R_GE_TX_DELAY_EN | YT8521_RC1R_FE_TX_DELAY_EN;
- val |= YT8521_RC1R_RX_DELAY_EN;
- break;
- case PHY_INTERFACE_MODE_SGMII:
- break;
- default: /* do not support other modes */
- ret = -EOPNOTSUPP;
- goto err_restore_page;
- }
-
/* set rgmii delay mode */
if (phydev->interface != PHY_INTERFACE_MODE_SGMII) {
- ret = ytphy_modify_ext(phydev, YT8521_RGMII_CONFIG1_REG,
- (YT8521_RC1R_RX_DELAY_MASK |
- YT8521_RC1R_FE_TX_DELAY_MASK |
- YT8521_RC1R_GE_TX_DELAY_MASK),
- val);
+ ret = ytphy_rgmii_clk_delay_config(phydev);
if (ret < 0)
goto err_restore_page;
}
- /* disable auto sleep */
- ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG,
- YT8521_ESC1R_SLEEP_SW, 0);
- if (ret < 0)
- goto err_restore_page;
-
- /* enable RXC clock when no wire plug */
- ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG,
- YT8521_CGR_RX_CLK_EN, 0);
- if (ret < 0)
- goto err_restore_page;
+ if (of_property_read_bool(node, "motorcomm,auto-sleep-disabled")) {
+ /* disable auto sleep */
+ ret = ytphy_modify_ext(phydev, YT8521_EXTREG_SLEEP_CONTROL1_REG,
+ YT8521_ESC1R_SLEEP_SW, 0);
+ if (ret < 0)
+ goto err_restore_page;
+ }
+ if (of_property_read_bool(node, "motorcomm,keep-pll-enabled")) {
+ /* enable RXC clock when no wire plug */
+ ret = ytphy_modify_ext(phydev, YT8521_CLOCK_GATING_REG,
+ YT8521_CGR_RX_CLK_EN, 0);
+ if (ret < 0)
+ goto err_restore_page;
+ }
err_restore_page:
return phy_restore_page(phydev, old_page, ret);
}
Add dts support for Motorcomm yt8521 gigabit ethernet phy. Add ytphy_rgmii_clk_delay_config function to support dst config for the delay of rgmii clk. This funciont is common for yt8521, yt8531s and yt8531. This patch has been verified on AM335x platform. Signed-off-by: Frank Sae <Frank.Sae@motor-comm.com> --- drivers/net/phy/motorcomm.c | 253 ++++++++++++++++++++++++++++-------- 1 file changed, 199 insertions(+), 54 deletions(-)