@@ -268,6 +268,9 @@ struct kszphy_type {
u16 interrupt_level_mask;
u16 cable_diag_reg;
unsigned long pair_mask;
+ u16 disable_dll_tx_bit;
+ u16 disable_dll_rx_bit;
+ u16 disable_dll_mask;
bool has_broadcast_disable;
bool has_nand_tree_disable;
bool has_rmii_ref_clk_sel;
@@ -364,6 +367,19 @@ static const struct kszphy_type ksz9021_type = {
.interrupt_level_mask = BIT(14),
};
+static const struct kszphy_type ksz9131_type = {
+ .interrupt_level_mask = BIT(14),
+ .disable_dll_tx_bit = BIT(12),
+ .disable_dll_rx_bit = BIT(12),
+ .disable_dll_mask = BIT_MASK(12),
+};
+
+static const struct kszphy_type lan8841_type = {
+ .disable_dll_tx_bit = BIT(14),
+ .disable_dll_rx_bit = BIT(14),
+ .disable_dll_mask = BIT_MASK(14),
+};
+
static int kszphy_extended_write(struct phy_device *phydev,
u32 regnum, u16 val)
{
@@ -1172,19 +1188,18 @@ static int ksz9131_of_load_skew_values(struct phy_device *phydev,
#define KSZ9131RN_MMD_COMMON_CTRL_REG 2
#define KSZ9131RN_RXC_DLL_CTRL 76
#define KSZ9131RN_TXC_DLL_CTRL 77
-#define KSZ9131RN_DLL_CTRL_BYPASS BIT_MASK(12)
#define KSZ9131RN_DLL_ENABLE_DELAY 0
-#define KSZ9131RN_DLL_DISABLE_DELAY BIT(12)
static int ksz9131_config_rgmii_delay(struct phy_device *phydev)
{
+ const struct kszphy_type *type = phydev->drv->driver_data;
u16 rxcdll_val, txcdll_val;
int ret;
switch (phydev->interface) {
case PHY_INTERFACE_MODE_RGMII:
- rxcdll_val = KSZ9131RN_DLL_DISABLE_DELAY;
- txcdll_val = KSZ9131RN_DLL_DISABLE_DELAY;
+ rxcdll_val = type->disable_dll_rx_bit;
+ txcdll_val = type->disable_dll_tx_bit;
break;
case PHY_INTERFACE_MODE_RGMII_ID:
rxcdll_val = KSZ9131RN_DLL_ENABLE_DELAY;
@@ -1192,10 +1207,10 @@ static int ksz9131_config_rgmii_delay(struct phy_device *phydev)
break;
case PHY_INTERFACE_MODE_RGMII_RXID:
rxcdll_val = KSZ9131RN_DLL_ENABLE_DELAY;
- txcdll_val = KSZ9131RN_DLL_DISABLE_DELAY;
+ txcdll_val = type->disable_dll_tx_bit;
break;
case PHY_INTERFACE_MODE_RGMII_TXID:
- rxcdll_val = KSZ9131RN_DLL_DISABLE_DELAY;
+ rxcdll_val = type->disable_dll_rx_bit;
txcdll_val = KSZ9131RN_DLL_ENABLE_DELAY;
break;
default:
@@ -1203,13 +1218,13 @@ static int ksz9131_config_rgmii_delay(struct phy_device *phydev)
}
ret = phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG,
- KSZ9131RN_RXC_DLL_CTRL, KSZ9131RN_DLL_CTRL_BYPASS,
+ KSZ9131RN_RXC_DLL_CTRL, type->disable_dll_mask,
rxcdll_val);
if (ret < 0)
return ret;
return phy_modify_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG,
- KSZ9131RN_TXC_DLL_CTRL, KSZ9131RN_DLL_CTRL_BYPASS,
+ KSZ9131RN_TXC_DLL_CTRL, type->disable_dll_mask,
txcdll_val);
}
@@ -3152,6 +3167,144 @@ static int lan8814_probe(struct phy_device *phydev)
return 0;
}
+#define LAN8841_MMD_TIMER_REG 0
+#define LAN8841_MMD0_REGISTER_17 17
+#define LAN8841_MMD0_REGISTER_17_DROP_OPT(x) ((x) & 0x3)
+#define LAN8841_MMD0_REGISTER_17_XMIT_TOG_TX_DIS BIT(3)
+#define LAN8841_OPERATION_MODE_STRAP_OVERRIDE_LOW_REG 2
+#define LAN8841_OPERATION_MODE_STRAP_OVERRIDE_LOW_REG_MAGJACK BIT(14)
+#define LAN8841_MMD_ANALOG_REG 28
+#define LAN8841_ANALOG_CONTROL_1 1
+#define LAN8841_ANALOG_CONTROL_1_PLL_TRIM(x) (((x) & 0x3) << 5)
+#define LAN8841_ANALOG_CONTROL_10 13
+#define LAN8841_ANALOG_CONTROL_10_PLL_DIV(x) ((x) & 0x3)
+#define LAN8841_ANALOG_CONTROL_11 14
+#define LAN8841_ANALOG_CONTROL_11_LDO_REF(x) (((x) & 0x7) << 12)
+#define LAN8841_TX_LOW_I_CH_C_D_POWER_MANAGMENT 69
+#define LAN8841_TX_LOW_I_CH_C_D_POWER_MANAGMENT_VAL 0xbffc
+#define LAN8841_BTRX_POWER_DOWN 70
+#define LAN8841_BTRX_POWER_DOWN_QBIAS_CH_A BIT(0)
+#define LAN8841_BTRX_POWER_DOWN_BTRX_CH_A BIT(1)
+#define LAN8841_BTRX_POWER_DOWN_QBIAS_CH_B BIT(2)
+#define LAN8841_BTRX_POWER_DOWN_BTRX_CH_B BIT(3)
+#define LAN8841_BTRX_POWER_DOWN_BTRX_CH_C BIT(5)
+#define LAN8841_BTRX_POWER_DOWN_BTRX_CH_D BIT(7)
+#define LAN8841_ADC_CHANNEL_MASK 198
+static int lan8841_config_init(struct phy_device *phydev)
+{
+ int err;
+ int ret;
+
+ err = ksz9131_config_init(phydev);
+ if (err)
+ return err;
+
+ /* 100BT Clause 40 improvenent errata */
+ phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG,
+ LAN8841_ANALOG_CONTROL_1,
+ LAN8841_ANALOG_CONTROL_1_PLL_TRIM(0x2));
+ phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG,
+ LAN8841_ANALOG_CONTROL_10,
+ LAN8841_ANALOG_CONTROL_10_PLL_DIV(0x1));
+
+ /* 10M/100M Ethernet Signal Tuning Errata for Shorted-Center Tap
+ * Magnetics
+ */
+ ret = phy_read_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG,
+ LAN8841_OPERATION_MODE_STRAP_OVERRIDE_LOW_REG);
+ if (ret & LAN8841_OPERATION_MODE_STRAP_OVERRIDE_LOW_REG_MAGJACK) {
+ phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG,
+ LAN8841_TX_LOW_I_CH_C_D_POWER_MANAGMENT,
+ LAN8841_TX_LOW_I_CH_C_D_POWER_MANAGMENT_VAL);
+ phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG,
+ LAN8841_BTRX_POWER_DOWN,
+ LAN8841_BTRX_POWER_DOWN_QBIAS_CH_A |
+ LAN8841_BTRX_POWER_DOWN_BTRX_CH_A |
+ LAN8841_BTRX_POWER_DOWN_QBIAS_CH_B |
+ LAN8841_BTRX_POWER_DOWN_BTRX_CH_B |
+ LAN8841_BTRX_POWER_DOWN_BTRX_CH_C |
+ LAN8841_BTRX_POWER_DOWN_BTRX_CH_D);
+ }
+
+ /* LDO Adjustment errata */
+ phy_write_mmd(phydev, LAN8841_MMD_ANALOG_REG,
+ LAN8841_ANALOG_CONTROL_11,
+ LAN8841_ANALOG_CONTROL_11_LDO_REF(1));
+
+ /* 100BT RGMII latency tuning errata */
+ phy_write_mmd(phydev, MDIO_MMD_PMAPMD,
+ LAN8841_ADC_CHANNEL_MASK, 0x0);
+ phy_write_mmd(phydev, LAN8841_MMD_TIMER_REG,
+ LAN8841_MMD0_REGISTER_17,
+ LAN8841_MMD0_REGISTER_17_DROP_OPT(2) |
+ LAN8841_MMD0_REGISTER_17_XMIT_TOG_TX_DIS);
+
+ return 0;
+}
+
+#define LAN8841_OUTPUT_CTRL 25
+#define LAN8841_OUTPUT_CTRL_INT_BUFFER BIT(14)
+static int lan8841_config_intr(struct phy_device *phydev)
+{
+ int err;
+
+ phy_modify(phydev, LAN8841_OUTPUT_CTRL,
+ LAN8841_OUTPUT_CTRL_INT_BUFFER, 0);
+
+ if (phydev->interrupts == PHY_INTERRUPT_ENABLED) {
+ err = phy_read(phydev, LAN8814_INTS);
+ if (err)
+ return err;
+
+ err = phy_write(phydev, LAN8814_INTC,
+ LAN8814_INT_LINK);
+ } else {
+ err = phy_write(phydev, LAN8814_INTC, 0);
+ if (err)
+ return err;
+
+ err = phy_read(phydev, LAN8814_INTS);
+ }
+
+ return err;
+}
+
+static irqreturn_t lan8841_handle_interrupt(struct phy_device *phydev)
+{
+ int irq_status;
+
+ irq_status = phy_read(phydev, LAN8814_INTS);
+ if (irq_status < 0) {
+ phy_error(phydev);
+ return IRQ_NONE;
+ }
+
+ if (irq_status & LAN8814_INT_LINK) {
+ phy_trigger_machine(phydev);
+ return IRQ_HANDLED;
+ }
+
+ return IRQ_NONE;
+}
+
+#define LAN8841_OPERATION_MODE_STRAP_LOW_REGISTER 3
+#define LAN8841_OPERATION_MODE_STRAP_LOW_REGISTER_STRAP_RGMII_EN BIT(0)
+static int lan8841_probe(struct phy_device *phydev)
+{
+ int err;
+
+ err = kszphy_probe(phydev);
+ if (err)
+ return err;
+
+ if (phy_read_mmd(phydev, KSZ9131RN_MMD_COMMON_CTRL_REG,
+ LAN8841_OPERATION_MODE_STRAP_LOW_REGISTER) &
+ LAN8841_OPERATION_MODE_STRAP_LOW_REGISTER_STRAP_RGMII_EN)
+ phydev->interface = PHY_INTERFACE_MODE_RGMII_RXID;
+
+ return 0;
+}
+
static struct phy_driver ksphy_driver[] = {
{
.phy_id = PHY_ID_KS8737,
@@ -3361,13 +3514,28 @@ static struct phy_driver ksphy_driver[] = {
.resume = kszphy_resume,
.config_intr = lan8804_config_intr,
.handle_interrupt = lan8804_handle_interrupt,
+}, {
+ .phy_id = PHY_ID_LAN8841,
+ .phy_id_mask = MICREL_PHY_ID_MASK,
+ .name = "Microchip LAN8841 Gigabit PHY",
+ .driver_data = &lan8841_type,
+ .config_init = lan8841_config_init,
+ .probe = lan8841_probe,
+ .soft_reset = genphy_soft_reset,
+ .config_intr = lan8841_config_intr,
+ .handle_interrupt = lan8841_handle_interrupt,
+ .get_sset_count = kszphy_get_sset_count,
+ .get_strings = kszphy_get_strings,
+ .get_stats = kszphy_get_stats,
+ .suspend = genphy_suspend,
+ .resume = genphy_resume,
}, {
.phy_id = PHY_ID_KSZ9131,
.phy_id_mask = MICREL_PHY_ID_MASK,
.name = "Microchip KSZ9131 Gigabit PHY",
/* PHY_GBIT_FEATURES */
.flags = PHY_POLL_CABLE_TEST,
- .driver_data = &ksz9021_type,
+ .driver_data = &ksz9131_type,
.probe = kszphy_probe,
.config_init = ksz9131_config_init,
.config_intr = kszphy_config_intr,
@@ -3446,6 +3614,7 @@ static struct mdio_device_id __maybe_unused micrel_tbl[] = {
{ PHY_ID_KSZ886X, MICREL_PHY_ID_MASK },
{ PHY_ID_LAN8814, MICREL_PHY_ID_MASK },
{ PHY_ID_LAN8804, MICREL_PHY_ID_MASK },
+ { PHY_ID_LAN8841, MICREL_PHY_ID_MASK },
{ }
};
@@ -31,6 +31,7 @@
#define PHY_ID_KSZ9131 0x00221640
#define PHY_ID_LAN8814 0x00221660
#define PHY_ID_LAN8804 0x00221670
+#define PHY_ID_LAN8841 0x00221650
#define PHY_ID_KSZ886X 0x00221430
#define PHY_ID_KSZ8863 0x00221435
The LAN8841 is completely integrated triple-speed (10BASE-T/ 100BASE-TX/ 1000BASE-T) Ethernet physical layer transceivers for transmission and reception of data on standard CAT-5, as well as CAT-5e and CAT-6, unshielded twisted pair (UTP) cables. The LAN8841 offers the industry-standard GMII/MII as well as the RGMII. Some of the features of the PHY are: - Wake on LAN - Auto-MDIX - IEEE 1588-2008 (V2) - LinkMD Capable diagnosis Currently the patch offers support only for link configuration. Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com> --- drivers/net/phy/micrel.c | 187 +++++++++++++++++++++++++++++++++++-- include/linux/micrel_phy.h | 1 + 2 files changed, 179 insertions(+), 9 deletions(-)