@@ -1800,7 +1800,8 @@ static int
qca8k_setup(struct dsa_switch *ds)
{
struct qca8k_priv *priv = ds->priv;
- int cpu_port, ret, i;
+ struct dsa_port *dp;
+ int cpu_port, ret;
u32 mask;
cpu_port = qca8k_find_cpu_port(ds);
@@ -1855,27 +1856,27 @@ qca8k_setup(struct dsa_switch *ds)
dev_warn(priv->dev, "mib init failed");
/* Initial setup of all ports */
- for (i = 0; i < QCA8K_NUM_PORTS; i++) {
+ dsa_switch_for_each_port(dp, ds) {
/* Disable forwarding by default on all ports */
- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(dp->index),
QCA8K_PORT_LOOKUP_MEMBER, 0);
if (ret)
return ret;
+ }
- /* Enable QCA header mode on all cpu ports */
- if (dsa_is_cpu_port(ds, i)) {
- ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(i),
- FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) |
- FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL));
- if (ret) {
- dev_err(priv->dev, "failed enabling QCA header mode");
- return ret;
- }
+ /* Disable MAC by default on all user ports */
+ dsa_switch_for_each_user_port(dp, ds)
+ qca8k_port_set_status(priv, dp->index, 0);
+
+ /* Enable QCA header mode on all cpu ports */
+ dsa_switch_for_each_cpu_port(dp, ds) {
+ ret = qca8k_write(priv, QCA8K_REG_PORT_HDR_CTRL(dp->index),
+ FIELD_PREP(QCA8K_PORT_HDR_CTRL_TX_MASK, QCA8K_PORT_HDR_CTRL_ALL) |
+ FIELD_PREP(QCA8K_PORT_HDR_CTRL_RX_MASK, QCA8K_PORT_HDR_CTRL_ALL));
+ if (ret) {
+ dev_err(priv->dev, "failed enabling QCA header mode on port %d", dp->index);
+ return ret;
}
-
- /* Disable MAC by default on all user ports */
- if (dsa_is_user_port(ds, i))
- qca8k_port_set_status(priv, i, 0);
}
/* Forward all unknown frames to CPU port for Linux processing
@@ -1897,48 +1898,48 @@ qca8k_setup(struct dsa_switch *ds)
return ret;
/* Setup connection between CPU port & user ports
- * Configure specific switch configuration for ports
+ * Individual user ports get connected to CPU port only
*/
- for (i = 0; i < QCA8K_NUM_PORTS; i++) {
- /* Individual user ports get connected to CPU port only */
- if (dsa_is_user_port(ds, i)) {
- ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(i),
- QCA8K_PORT_LOOKUP_MEMBER,
- BIT(cpu_port));
- if (ret)
- return ret;
-
- ret = regmap_clear_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(i),
- QCA8K_PORT_LOOKUP_LEARN);
- if (ret)
- return ret;
-
- /* For port based vlans to work we need to set the
- * default egress vid
- */
- ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(i),
- QCA8K_EGREES_VLAN_PORT_MASK(i),
- QCA8K_EGREES_VLAN_PORT(i, QCA8K_PORT_VID_DEF));
- if (ret)
- return ret;
-
- ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(i),
- QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) |
- QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF));
- if (ret)
- return ret;
- }
+ dsa_switch_for_each_user_port(dp, ds) {
+ u8 port = dp->index;
+
+ ret = qca8k_rmw(priv, QCA8K_PORT_LOOKUP_CTRL(port),
+ QCA8K_PORT_LOOKUP_MEMBER,
+ BIT(cpu_port));
+ if (ret)
+ return ret;
+
+ ret = regmap_clear_bits(priv->regmap, QCA8K_PORT_LOOKUP_CTRL(port),
+ QCA8K_PORT_LOOKUP_LEARN);
+ if (ret)
+ return ret;
- /* The port 5 of the qca8337 have some problem in flood condition. The
- * original legacy driver had some specific buffer and priority settings
- * for the different port suggested by the QCA switch team. Add this
- * missing settings to improve switch stability under load condition.
- * This problem is limited to qca8337 and other qca8k switch are not affected.
+ /* For port based vlans to work we need to set the
+ * default egress vid
*/
- if (priv->switch_id == QCA8K_ID_QCA8337)
- qca8k_setup_hol_fixup(priv, i);
+ ret = qca8k_rmw(priv, QCA8K_EGRESS_VLAN(port),
+ QCA8K_EGREES_VLAN_PORT_MASK(port),
+ QCA8K_EGREES_VLAN_PORT(port, QCA8K_PORT_VID_DEF));
+ if (ret)
+ return ret;
+
+ ret = qca8k_write(priv, QCA8K_REG_PORT_VLAN_CTRL0(port),
+ QCA8K_PORT_VLAN_CVID(QCA8K_PORT_VID_DEF) |
+ QCA8K_PORT_VLAN_SVID(QCA8K_PORT_VID_DEF));
+ if (ret)
+ return ret;
}
+ /* The port 5 of the qca8337 have some problem in flood condition. The
+ * original legacy driver had some specific buffer and priority settings
+ * for the different port suggested by the QCA switch team. Add this
+ * missing settings to improve switch stability under load condition.
+ * This problem is limited to qca8337 and other qca8k switch are not affected.
+ */
+ if (priv->switch_id == QCA8K_ID_QCA8337)
+ dsa_switch_for_each_available_port(dp, ds)
+ qca8k_setup_hol_fixup(priv, dp->index);
+
/* Special GLOBAL_FC_THRESH value are needed for ar8327 switch */
if (priv->switch_id == QCA8K_ID_QCA8327) {
mask = QCA8K_GLOBAL_FC_GOL_XON_THRES(288) |
Convert for loop to dsa_for_each macro to save some redundant write on unconnected/unused port and tidy things up. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> --- changes v3: - Fix compilation error with unfinished patch in v2 drivers/net/dsa/qca/qca8k-8xxx.c | 107 ++++++++++++++++--------------- 1 file changed, 54 insertions(+), 53 deletions(-)