@@ -459,21 +459,27 @@ static int at803x_set_wol(struct phy_device *phydev,
phy_write_mmd(phydev, MDIO_MMD_PCS, offsets[i],
mac[(i * 2) + 1] | (mac[(i * 2)] << 8));
- /* Enable WOL function */
- ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_PHY_MMD3_WOL_CTRL,
- 0, AT803X_WOL_EN);
- if (ret)
- return ret;
+ /* Enable WOL function for 1588 */
+ if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+ ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+ AT803X_PHY_MMD3_WOL_CTRL,
+ 0, AT803X_WOL_EN);
+ if (ret)
+ return ret;
+ }
/* Enable WOL interrupt */
ret = phy_modify(phydev, AT803X_INTR_ENABLE, 0, AT803X_INTR_ENABLE_WOL);
if (ret)
return ret;
} else {
- /* Disable WoL function */
- ret = phy_modify_mmd(phydev, MDIO_MMD_PCS, AT803X_PHY_MMD3_WOL_CTRL,
- AT803X_WOL_EN, 0);
- if (ret)
- return ret;
+ /* Disable WoL function for 1588 */
+ if (phydev->drv->phy_id == ATH8031_PHY_ID) {
+ ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+ AT803X_PHY_MMD3_WOL_CTRL,
+ AT803X_WOL_EN, 0);
+ if (ret)
+ return ret;
+ }
/* Disable WOL interrupt */
ret = phy_modify(phydev, AT803X_INTR_ENABLE, AT803X_INTR_ENABLE_WOL, 0);
if (ret)
@@ -508,11 +514,11 @@ static void at803x_get_wol(struct phy_device *phydev,
wol->supported = WAKE_MAGIC;
wol->wolopts = 0;
- value = phy_read_mmd(phydev, MDIO_MMD_PCS, AT803X_PHY_MMD3_WOL_CTRL);
+ value = phy_read(phydev, AT803X_INTR_ENABLE);
if (value < 0)
return;
- if (value & AT803X_WOL_EN)
+ if (value & AT803X_INTR_ENABLE_WOL)
wol->wolopts |= WAKE_MAGIC;
}
@@ -858,9 +864,6 @@ static int at803x_probe(struct phy_device *phydev)
if (phydev->drv->phy_id == ATH8031_PHY_ID) {
int ccr = phy_read(phydev, AT803X_REG_CHIP_CONFIG);
int mode_cfg;
- struct ethtool_wolinfo wol = {
- .wolopts = 0,
- };
if (ccr < 0)
return ccr;
@@ -877,12 +880,14 @@ static int at803x_probe(struct phy_device *phydev)
break;
}
- /* Disable WOL by default */
- ret = at803x_set_wol(phydev, &wol);
- if (ret < 0) {
- phydev_err(phydev, "failed to disable WOL on probe: %d\n", ret);
+ /* Disable WoL in 1588 register which is enabled
+ * by default
+ */
+ ret = phy_modify_mmd(phydev, MDIO_MMD_PCS,
+ AT803X_PHY_MMD3_WOL_CTRL,
+ AT803X_WOL_EN, 0);
+ if (ret)
return ret;
- }
}
return 0;
In commit 7beecaf7d507 ("net: phy: at803x: improve the WOL feature"), it seems not correct to use a wol_en bit in a 1588 Control Register which is only available on AR8031/AR8033(share the same phy_id) to determine if WoL is enabled. Change it back to use AT803X_INTR_ENABLE_WOL for determining the WoL status which is applicable on all chips supporting wol. Also update the at803x_set_wol() function to only update the 1588 register on chips having it. After this change, disabling wol at probe from commit d7cd5e06c9dd ("net: phy: at803x: disable WOL at probe") is no longer needed. Change it to just disable the WoL bit in 1588 register for AR8031/AR8033 to be aligned with AT803X_INTR_ENABLE_WOL in probe. Fixes: 7beecaf7d507 ("net: phy: at803x: improve the WOL feature") Signed-off-by: Li Yang <leoyang.li@nxp.com> Reviewed-by: Viorel Suman <viorel.suman@nxp.com> Reviewed-by: Wei Fang <wei.fang@nxp.com> --- drivers/net/phy/at803x.c | 45 ++++++++++++++++++++++------------------ 1 file changed, 25 insertions(+), 20 deletions(-)