| Message ID | 20240203142559.130466-2-biju.das.jz@bp.renesas.com (mailing list archive) |
|---|---|
| State | Superseded |
| Delegated to: | Netdev Maintainers |
| Headers | show |
| Series | Add HW checksum offload support for RZ/G2L GbEthernet IP | expand |
On 2/3/24 5:25 PM, Biju Das wrote: > TOE has hardware support for calculating IP header and TCP/UDP/ICMP > checksum for both IPv4 and IPv6. > > Add Rx checksum offload supported by TOE for IPv4 and TCP/UDP protocols. > > For Rx, the 4-byte result of checksum calculation is attached to the > Ethernet frames.First 2-bytes is result of IPv4 header checksum and next > 2-bytes is TCP/UDP/ICMP checksum. > > If a frame does not have checksum error, 0x0000 is attached as checksum > calculation result. For unsupported frames 0xFFFF is attached as checksum > calculation result. In case of an IPv6 packet, IPv4 checksum is always set > to 0xFFFF. > > We can test this functionality by the below commands > > ethtool -K eth0 rx on --> to turn on Rx checksum offload > ethtool -K eth0 rx off --> to turn off Rx checksum offload > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> [...] > diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h > index e0f8276cffed..64bf29d01ad0 100644 > --- a/drivers/net/ethernet/renesas/ravb.h > +++ b/drivers/net/ethernet/renesas/ravb.h > @@ -205,7 +205,10 @@ enum ravb_reg { > TLFRCR = 0x0758, > RFCR = 0x0760, > MAFCR = 0x0778, > - CSR0 = 0x0800, /* RZ/G2L only */ > + > + /* RZ/G2L TOE registers */ Thanks. Though I think I'd prefer /* TOE registers (RZ/G2L only) */... [...] > @@ -978,6 +981,21 @@ enum CSR0_BIT { > CSR0_RPE = 0x00000020, > }; > > +enum CSR2_BIT { > + CSR2_RIP4 = 0x00000001, > + CSR2_RTCP4 = 0x00000010, > + CSR2_RUDP4 = 0x00000020, > + CSR2_RICMP4 = 0x00000040, > + CSR2_RTCP6 = 0x00100000, > + CSR2_RUDP6 = 0x00200000, > + CSR2_RICMP6 = 0x00400000, > + CSR2_RHOP = 0x01000000, > + CSR2_RROUT = 0x02000000, > + CSR2_RAHD = 0x04000000, > + CSR2_RDHD = 0x08000000, > + CSR2_ALL = 0x0F700071, I doubt we really need CSR2_ALL... [...] > diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c > index 0e3731f50fc2..4f310bcee7c0 100644 > --- a/drivers/net/ethernet/renesas/ravb_main.c > +++ b/drivers/net/ethernet/renesas/ravb_main.c > @@ -522,6 +522,24 @@ static int ravb_ring_init(struct net_device *ndev, int q) > return -ENOMEM; > } > > +static void ravb_csum_init_gbeth(struct net_device *ndev) > +{ > + if (!(ndev->features & NETIF_F_RXCSUM)) > + goto done; > + > + ravb_write(ndev, 0, CSR0); > + if (ravb_wait(ndev, CSR0, CSR0_RPE, 0)) { > + netdev_err(ndev, "Timeout enabling hardware checksum\n"); > + ndev->features &= ~NETIF_F_RXCSUM; > + } else { > + ravb_write(ndev, CSR2_ALL & ~(CSR2_RTCP6 | CSR2_RUDP6 | > + CSR2_RICMP6), CSR2); With these 3 bits being 0, the bits 24...27 are ignored anyway, the manual says. So I think I'd prefer: ravb_write(ndev, CSR2_RIP4 | CSR2_RTCP4 | CSR2_RUDP4 | CSR2_RICMP4, CSR2); > + } > + > +done: > + ravb_write(ndev, CSR0_TPE | CSR0_RPE, CSR0); I think we shouldn't set CSR0.TPE yet at this point, as we n't setup CSR1 yet... [...] > @@ -2334,11 +2381,48 @@ static void ravb_set_rx_csum(struct net_device *ndev, bool enable) [...] > static int ravb_set_features_gbeth(struct net_device *ndev, > netdev_features_t features) > { > - /* Place holder */ > - return 0; > + netdev_features_t changed = ndev->features ^ features; > + struct ravb_private *priv = netdev_priv(ndev); > + unsigned long flags; > + int ret = 0; > + u32 val; > + > + spin_lock_irqsave(&priv->lock, flags); > + if (changed & NETIF_F_RXCSUM) { > + if (features & NETIF_F_RXCSUM) > + val = CSR2_ALL & ~(CSR2_RTCP6 | CSR2_RUDP6 | CSR2_RICMP6); Likewise, I'd prefer: val = CSR2_RIP4 | CSR2_RTCP4 | CSR2_RUDP4 | CSR2_RICMP4; > + else > + val = 0; > + > + ret = ravb_endisable_csum_gbeth(ndev, CSR2, val, CSR0_RPE); > + if (ret) > + goto done; > + } > + > + ndev->features = features; > +done: > + spin_unlock_irqrestore(&priv->lock, flags); > + > + return ret; > } > > static int ravb_set_features_rcar(struct net_device *ndev, [...] Otherwise LGTM. We're close! :-) MBR, Sergey
Hi Sergey Shtylyov, Thanks for the feedback. > -----Original Message----- > From: Sergey Shtylyov <s.shtylyov@omp.ru> > Sent: Monday, February 5, 2024 7:01 PM > Subject: Re: [PATCH v4 net-next 1/2] ravb: Add Rx checksum offload support > for GbEth > > On 2/3/24 5:25 PM, Biju Das wrote: > > > TOE has hardware support for calculating IP header and TCP/UDP/ICMP > > checksum for both IPv4 and IPv6. > > > > Add Rx checksum offload supported by TOE for IPv4 and TCP/UDP protocols. > > > > For Rx, the 4-byte result of checksum calculation is attached to the > > Ethernet frames.First 2-bytes is result of IPv4 header checksum and > > next 2-bytes is TCP/UDP/ICMP checksum. > > > > If a frame does not have checksum error, 0x0000 is attached as > > checksum calculation result. For unsupported frames 0xFFFF is attached > > as checksum calculation result. In case of an IPv6 packet, IPv4 > > checksum is always set to 0xFFFF. > > > > We can test this functionality by the below commands > > > > ethtool -K eth0 rx on --> to turn on Rx checksum offload ethtool -K > > eth0 rx off --> to turn off Rx checksum offload > > > > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> > [...] > > > diff --git a/drivers/net/ethernet/renesas/ravb.h > > b/drivers/net/ethernet/renesas/ravb.h > > index e0f8276cffed..64bf29d01ad0 100644 > > --- a/drivers/net/ethernet/renesas/ravb.h > > +++ b/drivers/net/ethernet/renesas/ravb.h > > @@ -205,7 +205,10 @@ enum ravb_reg { > > TLFRCR = 0x0758, > > RFCR = 0x0760, > > MAFCR = 0x0778, > > - CSR0 = 0x0800, /* RZ/G2L only */ > > + > > + /* RZ/G2L TOE registers */ > > Thanks. Though I think I'd prefer /* TOE registers (RZ/G2L only) */... OK. > > [...] > > @@ -978,6 +981,21 @@ enum CSR0_BIT { > > CSR0_RPE = 0x00000020, > > }; > > > > +enum CSR2_BIT { > > + CSR2_RIP4 = 0x00000001, > > + CSR2_RTCP4 = 0x00000010, > > + CSR2_RUDP4 = 0x00000020, > > + CSR2_RICMP4 = 0x00000040, > > + CSR2_RTCP6 = 0x00100000, > > + CSR2_RUDP6 = 0x00200000, > > + CSR2_RICMP6 = 0x00400000, > > + CSR2_RHOP = 0x01000000, > > + CSR2_RROUT = 0x02000000, > > + CSR2_RAHD = 0x04000000, > > + CSR2_RDHD = 0x08000000, > > + CSR2_ALL = 0x0F700071, > > I doubt we really need CSR2_ALL... Will remove it. > > [...] > > diff --git a/drivers/net/ethernet/renesas/ravb_main.c > > b/drivers/net/ethernet/renesas/ravb_main.c > > index 0e3731f50fc2..4f310bcee7c0 100644 > > --- a/drivers/net/ethernet/renesas/ravb_main.c > > +++ b/drivers/net/ethernet/renesas/ravb_main.c > > @@ -522,6 +522,24 @@ static int ravb_ring_init(struct net_device *ndev, > int q) > > return -ENOMEM; > > } > > > > +static void ravb_csum_init_gbeth(struct net_device *ndev) { > > + if (!(ndev->features & NETIF_F_RXCSUM)) > > + goto done; > > + > > + ravb_write(ndev, 0, CSR0); > > + if (ravb_wait(ndev, CSR0, CSR0_RPE, 0)) { > > + netdev_err(ndev, "Timeout enabling hardware checksum\n"); > > + ndev->features &= ~NETIF_F_RXCSUM; > > + } else { > > + ravb_write(ndev, CSR2_ALL & ~(CSR2_RTCP6 | CSR2_RUDP6 | > > + CSR2_RICMP6), CSR2); > > With these 3 bits being 0, the bits 24...27 are ignored anyway, the > manual says. So I think I'd prefer: > > ravb_write(ndev, CSR2_RIP4 | CSR2_RTCP4 | CSR2_RUDP4 | > CSR2_RICMP4, > CSR2); OK. > > > + } > > + > > +done: > > + ravb_write(ndev, CSR0_TPE | CSR0_RPE, CSR0); > > I think we shouldn't set CSR0.TPE yet at this point, as we n't setup > CSR1 yet... This will cause regression. As board won't boot as tx fails. So CSR0.{TPE,RPE} is must. > > [...] > > @@ -2334,11 +2381,48 @@ static void ravb_set_rx_csum(struct net_device > > *ndev, bool enable) > [...] > > static int ravb_set_features_gbeth(struct net_device *ndev, > > netdev_features_t features) > > { > > - /* Place holder */ > > - return 0; > > + netdev_features_t changed = ndev->features ^ features; > > + struct ravb_private *priv = netdev_priv(ndev); > > + unsigned long flags; > > + int ret = 0; > > + u32 val; > > + > > + spin_lock_irqsave(&priv->lock, flags); > > + if (changed & NETIF_F_RXCSUM) { > > + if (features & NETIF_F_RXCSUM) > > + val = CSR2_ALL & ~(CSR2_RTCP6 | CSR2_RUDP6 | > CSR2_RICMP6); > > Likewise, I'd prefer: > > val = CSR2_RIP4 | CSR2_RTCP4 | CSR2_RUDP4 | CSR2_RICMP4; Ok. > > > + else > > + val = 0; > > + > > + ret = ravb_endisable_csum_gbeth(ndev, CSR2, val, CSR0_RPE); > > + if (ret) > > + goto done; > > + } > > + > > + ndev->features = features; > > +done: > > + spin_unlock_irqrestore(&priv->lock, flags); > > + > > + return ret; > > } > > > > static int ravb_set_features_rcar(struct net_device *ndev, > [...] > > Otherwise LGTM. We're close! :-) I will send v5, based on above. Cheers, Biju
diff --git a/drivers/net/ethernet/renesas/ravb.h b/drivers/net/ethernet/renesas/ravb.h index e0f8276cffed..64bf29d01ad0 100644 --- a/drivers/net/ethernet/renesas/ravb.h +++ b/drivers/net/ethernet/renesas/ravb.h @@ -205,7 +205,10 @@ enum ravb_reg { TLFRCR = 0x0758, RFCR = 0x0760, MAFCR = 0x0778, - CSR0 = 0x0800, /* RZ/G2L only */ + + /* RZ/G2L TOE registers */ + CSR0 = 0x0800, + CSR2 = 0x0808, }; @@ -978,6 +981,21 @@ enum CSR0_BIT { CSR0_RPE = 0x00000020, }; +enum CSR2_BIT { + CSR2_RIP4 = 0x00000001, + CSR2_RTCP4 = 0x00000010, + CSR2_RUDP4 = 0x00000020, + CSR2_RICMP4 = 0x00000040, + CSR2_RTCP6 = 0x00100000, + CSR2_RUDP6 = 0x00200000, + CSR2_RICMP6 = 0x00400000, + CSR2_RHOP = 0x01000000, + CSR2_RROUT = 0x02000000, + CSR2_RAHD = 0x04000000, + CSR2_RDHD = 0x08000000, + CSR2_ALL = 0x0F700071, +}; + #define DBAT_ENTRY_NUM 22 #define RX_QUEUE_OFFSET 4 #define NUM_RX_QUEUE 2 diff --git a/drivers/net/ethernet/renesas/ravb_main.c b/drivers/net/ethernet/renesas/ravb_main.c index 0e3731f50fc2..4f310bcee7c0 100644 --- a/drivers/net/ethernet/renesas/ravb_main.c +++ b/drivers/net/ethernet/renesas/ravb_main.c @@ -522,6 +522,24 @@ static int ravb_ring_init(struct net_device *ndev, int q) return -ENOMEM; } +static void ravb_csum_init_gbeth(struct net_device *ndev) +{ + if (!(ndev->features & NETIF_F_RXCSUM)) + goto done; + + ravb_write(ndev, 0, CSR0); + if (ravb_wait(ndev, CSR0, CSR0_RPE, 0)) { + netdev_err(ndev, "Timeout enabling hardware checksum\n"); + ndev->features &= ~NETIF_F_RXCSUM; + } else { + ravb_write(ndev, CSR2_ALL & ~(CSR2_RTCP6 | CSR2_RUDP6 | + CSR2_RICMP6), CSR2); + } + +done: + ravb_write(ndev, CSR0_TPE | CSR0_RPE, CSR0); +} + static void ravb_emac_init_gbeth(struct net_device *ndev) { struct ravb_private *priv = netdev_priv(ndev); @@ -553,7 +571,8 @@ static void ravb_emac_init_gbeth(struct net_device *ndev) /* E-MAC status register clear */ ravb_write(ndev, ECSR_ICD | ECSR_LCHNG | ECSR_PFRI, ECSR); - ravb_write(ndev, CSR0_TPE | CSR0_RPE, CSR0); + + ravb_csum_init_gbeth(ndev); /* E-MAC interrupt enable register */ ravb_write(ndev, ECSIPR_ICDIP, ECSIPR); @@ -734,6 +753,30 @@ static void ravb_get_tx_tstamp(struct net_device *ndev) } } +static void ravb_rx_csum_gbeth(struct sk_buff *skb) +{ + __wsum csum_ip_hdr, csum_proto; + u8 *hw_csum; + + /* The hardware checksum status is contained in sizeof(__sum16) * 2 = 4 + * bytes appended to packet data. First 2 bytes is ip header checksum + * and last 2 bytes is protocol checksum. + */ + if (unlikely(skb->len < sizeof(__sum16) * 2)) + return; + + hw_csum = skb_tail_pointer(skb) - sizeof(__sum16); + csum_proto = csum_unfold((__force __sum16)get_unaligned_le16(hw_csum)); + + hw_csum -= sizeof(__sum16); + csum_ip_hdr = csum_unfold((__force __sum16)get_unaligned_le16(hw_csum)); + skb_trim(skb, skb->len - 2 * sizeof(__sum16)); + + /* TODO: IPV6 Rx checksum */ + if (skb->protocol == htons(ETH_P_IP) && !csum_ip_hdr && !csum_proto) + skb->ip_summed = CHECKSUM_UNNECESSARY; +} + static void ravb_rx_csum(struct sk_buff *skb) { u8 *hw_csum; @@ -819,6 +862,8 @@ static bool ravb_rx_gbeth(struct net_device *ndev, int *quota, int q) skb = ravb_get_skb_gbeth(ndev, entry, desc); skb_put(skb, pkt_len); skb->protocol = eth_type_trans(skb, ndev); + if (ndev->features & NETIF_F_RXCSUM) + ravb_rx_csum_gbeth(skb); napi_gro_receive(&priv->napi[q], skb); stats->rx_packets++; stats->rx_bytes += pkt_len; @@ -846,6 +891,8 @@ static bool ravb_rx_gbeth(struct net_device *ndev, int *quota, int q) dev_kfree_skb(skb); priv->rx_1st_skb->protocol = eth_type_trans(priv->rx_1st_skb, ndev); + if (ndev->features & NETIF_F_RXCSUM) + ravb_rx_csum_gbeth(skb); napi_gro_receive(&priv->napi[q], priv->rx_1st_skb); stats->rx_packets++; @@ -2334,11 +2381,48 @@ static void ravb_set_rx_csum(struct net_device *ndev, bool enable) spin_unlock_irqrestore(&priv->lock, flags); } +static int ravb_endisable_csum_gbeth(struct net_device *ndev, enum ravb_reg reg, + u32 val, u32 mask) +{ + u32 csr0 = CSR0_TPE | CSR0_RPE; + int ret; + + ravb_write(ndev, csr0 & ~mask, CSR0); + ret = ravb_wait(ndev, CSR0, mask, 0); + if (!ret) + ravb_write(ndev, val, reg); + + ravb_write(ndev, csr0, CSR0); + + return ret; +} + static int ravb_set_features_gbeth(struct net_device *ndev, netdev_features_t features) { - /* Place holder */ - return 0; + netdev_features_t changed = ndev->features ^ features; + struct ravb_private *priv = netdev_priv(ndev); + unsigned long flags; + int ret = 0; + u32 val; + + spin_lock_irqsave(&priv->lock, flags); + if (changed & NETIF_F_RXCSUM) { + if (features & NETIF_F_RXCSUM) + val = CSR2_ALL & ~(CSR2_RTCP6 | CSR2_RUDP6 | CSR2_RICMP6); + else + val = 0; + + ret = ravb_endisable_csum_gbeth(ndev, CSR2, val, CSR0_RPE); + if (ret) + goto done; + } + + ndev->features = features; +done: + spin_unlock_irqrestore(&priv->lock, flags); + + return ret; } static int ravb_set_features_rcar(struct net_device *ndev, @@ -2518,6 +2602,8 @@ static const struct ravb_hw_info gbeth_hw_info = { .emac_init = ravb_emac_init_gbeth, .gstrings_stats = ravb_gstrings_stats_gbeth, .gstrings_size = sizeof(ravb_gstrings_stats_gbeth), + .net_hw_features = NETIF_F_RXCSUM, + .net_features = NETIF_F_RXCSUM, .stats_len = ARRAY_SIZE(ravb_gstrings_stats_gbeth), .max_rx_len = ALIGN(GBETH_RX_BUFF_MAX, RAVB_ALIGN), .tccr_mask = TCCR_TSRQ0,
TOE has hardware support for calculating IP header and TCP/UDP/ICMP checksum for both IPv4 and IPv6. Add Rx checksum offload supported by TOE for IPv4 and TCP/UDP protocols. For Rx, the 4-byte result of checksum calculation is attached to the Ethernet frames.First 2-bytes is result of IPv4 header checksum and next 2-bytes is TCP/UDP/ICMP checksum. If a frame does not have checksum error, 0x0000 is attached as checksum calculation result. For unsupported frames 0xFFFF is attached as checksum calculation result. In case of an IPv6 packet, IPv4 checksum is always set to 0xFFFF. We can test this functionality by the below commands ethtool -K eth0 rx on --> to turn on Rx checksum offload ethtool -K eth0 rx off --> to turn off Rx checksum offload Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com> --- v3->v4: * Add separate section for RZ/G2L TOE registers in enum ravb_reg. * Dropped enabling IPv6 specific bits in CSR2. * The comment "csum" expanded to "checksum" in ravb_rx_csum_gbeth(). * Dropped unnecessary comment "Hardware validated our checksum". * Dropped reading CSR0 register in ravb_endisable_csum_gbeth(). v2->v3: * Updated commit header and description suggested by Sergey. * Dropped TOE_RX_CSUM_OK macro. * Renamed ravb_csum_offload_init_gbeth()->ravb_csum_init_gbeth(). * Moved enabling {RPE,TPE} in ravb_csum_init_gbeth(). * Updated the error message in ravb_csum_init_gbeth() as "Timeout enabling hardware checksum" * Introduced ravb_endisable_csum_gbeth() for enabling/disabling CSR{1,2} registers. v1->v2: * Fixed sparse warning by replacing __sum16->__wsum. --- drivers/net/ethernet/renesas/ravb.h | 20 +++++- drivers/net/ethernet/renesas/ravb_main.c | 92 +++++++++++++++++++++++- 2 files changed, 108 insertions(+), 4 deletions(-)