@@ -93,6 +93,7 @@ Contents:
plip
ppp_generic
proc_net_tcp
+ pse-pd/index
radiotap-headers
rds
regulatory
new file mode 100644
@@ -0,0 +1,9 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Power Sourcing Equipment (PSE) Documentation
+============================================
+
+.. toctree::
+ :maxdepth: 2
+
+ introduction
new file mode 100644
@@ -0,0 +1,73 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+Power Sourcing Equipment (PSE) in IEEE 802.3 Standard
+=====================================================
+
+Overview
+--------
+
+Power Sourcing Equipment (PSE) is essential in networks for delivering power
+along with data over Ethernet cables. It usually refers to devices like
+switches and hubs that supply power to Powered Devices (PDs) such as IP
+cameras, VoIP phones, and wireless access points.
+
+PSE vs. PoDL PSE
+----------------
+
+PSE in the IEEE 802.3 standard generally refers to equipment that provides
+power alongside data over Ethernet cables, typically associated with Power over
+Ethernet (PoE).
+
+PoDL PSE, or Power over Data Lines PSE, specifically denotes PSEs operating
+with single balanced twisted-pair PHYs, as per Clause 104 of IEEE 802.3. PoDL
+is significant in contexts like automotive and industrial controls where power
+and data delivery over a single pair is advantageous.
+
+IEEE 802.3-2018 Addendums and Related Clauses
+---------------------------------------------
+
+Key addenda to the IEEE 802.3-2018 standard relevant to power delivery over
+Ethernet are as follows:
+
+- **802.3af (Approved in 2003-06-12)**: Known as PoE in the market, detailed in
+ Clause 33, delivering up to 15.4W of power.
+- **802.3at (Approved in 2009-09-11)**: Marketed as PoE+, enhancing PoE as
+ covered in Clause 33, increasing power delivery to up to 30W.
+- **802.3bt (Approved in 2018-09-27)**: Known as 4PPoE in the market, outlined
+ in Clause 33. Type 3 delivers up to 60W, and Type 4 up to 100W.
+- **802.3bu (Approved in 2016-12-07)**: Formerly referred to as PoDL, detailed
+ in Clause 104. Introduces Classes 0 - 9. Class 9 PoDL PSE delivers up to ~65W
+
+Kernel Naming Convention Recommendations
+----------------------------------------
+
+For clarity and consistency within the Linux kernel's networking subsystem, the
+following naming conventions are recommended:
+
+- For general PSE (PoE) code, use "c33_pse" key words. For example:
+ ``enum ethtool_c33_pse_admin_state c33_admin_control;``.
+ This aligns with Clause 33, encompassing various PoE forms.
+
+- For PoDL PSE - specific code, use "podl_pse". For example:
+ ``enum ethtool_podl_pse_admin_state podl_admin_control;`` to differentiate
+ PoDL PSE settings according to Clause 104.
+
+Summary of Clause 33: Data Terminal Equipment (DTE) Power via Media Dependent Interface (MDI)
+---------------------------------------------------------------------------------------------
+
+Clause 33 of the IEEE 802.3 standard defines the functional and electrical
+characteristics of Powered Device (PD) and Power Sourcing Equipment (PSE).
+These entities enable power delivery using the same generic cabling as for data
+transmission, integrating power with data communication for devices such as
+10BASE-T, 100BASE-TX, or 1000BASE-T.
+
+Summary of Clause 104: Power over Data Lines (PoDL) of Single Balanced Twisted-Pair Ethernet
+--------------------------------------------------------------------------------------------
+
+Clause 104 of the IEEE 802.3 standard delineates the functional and electrical
+characteristics of PoDL Powered Devices (PDs) and PoDL Power Sourcing Equipment
+(PSEs). These are designed for use with single balanced twisted-pair Ethernet
+Physical Layers. In this clause, 'PSE' refers specifically to PoDL PSE, and
+'PD' to PoDL PD. The key intent is to provide devices with a unified interface
+for both data and the power required to process this data over a single
+balanced twisted-pair Ethernet connection.
@@ -17,9 +17,12 @@ struct pse_controller_dev;
*
* @podl_admin_control: set PoDL PSE admin control as described in
* IEEE 802.3-2018 30.15.1.2.1 acPoDLPSEAdminControl
+ * @c33_admin_control: set PSE admin control as described in
+ * IEEE 802.3-2022 30.9.1.2.1 acPSEAdminControl
*/
struct pse_control_config {
enum ethtool_podl_pse_admin_state podl_admin_control;
+ enum ethtool_c33_pse_admin_state c33_admin_control;
};
/**
@@ -29,10 +32,16 @@ struct pse_control_config {
* functions. IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState
* @podl_pw_status: power detection status of the PoDL PSE.
* IEEE 802.3-2018 30.15.1.1.3 aPoDLPSEPowerDetectionStatus:
+ * @c33_admin_state: operational state of the PSE
+ * functions. IEEE 802.3-2022 30.9.1.1.2 aPSEAdminState
+ * @c33_pw_status: power detection status of the PSE.
+ * IEEE 802.3-2022 30.9.1.1.5 aPSEPowerDetectionStatus:
*/
struct pse_control_status {
enum ethtool_podl_pse_admin_state podl_admin_state;
enum ethtool_podl_pse_pw_d_status podl_pw_status;
+ enum ethtool_c33_pse_admin_state c33_admin_state;
+ enum ethtool_c33_pse_pw_d_status c33_pw_status;
};
/**
@@ -752,6 +752,49 @@ enum ethtool_module_power_mode {
ETHTOOL_MODULE_POWER_MODE_HIGH,
};
+/**
+ * enum ethtool_c33_pse_admin_state - operational state of the PoDL PSE
+ * functions. IEEE 802.3-2022 30.9.1.1.2 aPSEAdminState
+ * @ETHTOOL_C33_PSE_ADMIN_STATE_UNKNOWN: state of PSE functions is unknown
+ * @ETHTOOL_C33_PSE_ADMIN_STATE_DISABLED: PSE functions are disabled
+ * @ETHTOOL_C33_PSE_ADMIN_STATE_ENABLED: PSE functions are enabled
+ */
+enum ethtool_c33_pse_admin_state {
+ ETHTOOL_C33_PSE_ADMIN_STATE_UNKNOWN = 1,
+ ETHTOOL_C33_PSE_ADMIN_STATE_DISABLED,
+ ETHTOOL_C33_PSE_ADMIN_STATE_ENABLED,
+};
+
+/**
+ * enum ethtool_c33_pse_pw_d_status - power detection status of the PSE.
+ * IEEE 802.3-2022 30.9.1.1.3 aPoDLPSEPowerDetectionStatus:
+ * @ETHTOOL_C33_PSE_PW_D_STATUS_UNKNOWN: PSE status is unknown
+ * @ETHTOOL_C33_PSE_PW_D_STATUS_DISABLED: "The enumeration \u201cdisabled\u201d
+ * indicates that the PSE State diagram is in the state DISABLED."
+ * @ETHTOOL_C33_PSE_PW_D_STATUS_SEARCHING: "The enumeration \u201csearching\u201d
+ * indicates the PSE State diagram is in a state other than those
+ * listed."
+ * @ETHTOOL_C33_PSE_PW_D_STATUS_DELIVERING: "The enumeration
+ * \u201cdeliveringPower\u201d indicates that the PSE State diagram is in the
+ * state POWER_ON."
+ * @ETHTOOL_C33_PSE_PW_D_STATUS_TEST: "The enumeration \u201ctest\u201d indicates that
+ * the PSE State diagram is in the state TEST_MODE."
+ * @ETHTOOL_C33_PSE_PW_D_STATUS_FAULT: "The enumeration \u201cfault\u201d indicates that
+ * the PSE State diagram is in the state TEST_ERROR."
+ * @ETHTOOL_C33_PSE_PW_D_STATUS_OTHERFAULT: "The enumeration \u201cotherFault\u201d
+ * indicates that the PSE State diagram is in the state IDLE due to
+ * the variable error_condition = true."
+ */
+enum ethtool_c33_pse_pw_d_status {
+ ETHTOOL_C33_PSE_PW_D_STATUS_UNKNOWN = 1,
+ ETHTOOL_C33_PSE_PW_D_STATUS_DISABLED,
+ ETHTOOL_C33_PSE_PW_D_STATUS_SEARCHING,
+ ETHTOOL_C33_PSE_PW_D_STATUS_DELIVERING,
+ ETHTOOL_C33_PSE_PW_D_STATUS_TEST,
+ ETHTOOL_C33_PSE_PW_D_STATUS_FAULT,
+ ETHTOOL_C33_PSE_PW_D_STATUS_OTHERFAULT,
+};
+
/**
* enum ethtool_podl_pse_admin_state - operational state of the PoDL PSE
* functions. IEEE 802.3-2018 30.15.1.1.2 aPoDLPSEAdminState
@@ -895,6 +895,9 @@ enum {
ETHTOOL_A_PODL_PSE_ADMIN_STATE, /* u32 */
ETHTOOL_A_PODL_PSE_ADMIN_CONTROL, /* u32 */
ETHTOOL_A_PODL_PSE_PW_D_STATUS, /* u32 */
+ ETHTOOL_A_C33_PSE_ADMIN_STATE, /* u32 */
+ ETHTOOL_A_C33_PSE_ADMIN_CONTROL, /* u32 */
+ ETHTOOL_A_C33_PSE_PW_D_STATUS, /* u32 */
/* add new constants above here */
__ETHTOOL_A_PSE_CNT,