@@ -1,5 +1,5 @@
# SPDX-License-Identifier: GPL-2.0
-# Copyright(c) 1999 - 2018 Intel Corporation.
+# Copyright(c) 1999 - 2024 Intel Corporation.
#
# Makefile for the Intel(R) 10GbE PCI Express ethernet driver
#
@@ -9,7 +9,7 @@ obj-$(CONFIG_IXGBE) += ixgbe.o
ixgbe-objs := ixgbe_main.o ixgbe_common.o ixgbe_ethtool.o \
ixgbe_82599.o ixgbe_82598.o ixgbe_phy.o ixgbe_sriov.o \
ixgbe_mbx.o ixgbe_x540.o ixgbe_x550.o ixgbe_lib.o ixgbe_ptp.o \
- ixgbe_xsk.o
+ ixgbe_xsk.o ixgbe_e610.o
ixgbe-$(CONFIG_IXGBE_DCB) += ixgbe_dcb.o ixgbe_dcb_82598.o \
ixgbe_dcb_82599.o ixgbe_dcb_nl.o
new file mode 100644
@@ -0,0 +1,492 @@
+// SPDX-License-Identifier: GPL-2.0
+/* Copyright(c) 1999 - 2024 Intel Corporation. */
+
+#include "ixgbe_common.h"
+#include "ixgbe_e610.h"
+#include "ixgbe_type.h"
+#include "ixgbe_x540.h"
+#include "ixgbe_phy.h"
+
+/**
+ * ixgbe_should_retry_aci_send_cmd_execute - decide if ACI command should
+ * be resent
+ * @opcode: ACI opcode
+ *
+ * Check if ACI command should be sent again depending on the provided opcode.
+ * It may happen when CSR is busy during link state changes.
+ *
+ * Return: true if the sending command routine should be repeated,
+ * otherwise false.
+ */
+static bool ixgbe_should_retry_aci_send_cmd_execute(u16 opcode)
+{
+ switch (opcode) {
+ case ixgbe_aci_opc_disable_rxen:
+ case ixgbe_aci_opc_get_phy_caps:
+ case ixgbe_aci_opc_get_link_status:
+ case ixgbe_aci_opc_get_link_topo:
+ return true;
+ }
+
+ return false;
+}
+
+/**
+ * ixgbe_aci_send_cmd_execute - execute sending FW Admin Command to FW Admin
+ * Command Interface
+ * @hw: pointer to the HW struct
+ * @desc: descriptor describing the command
+ * @buf: buffer to use for indirect commands (NULL for direct commands)
+ * @buf_size: size of buffer for indirect commands (0 for direct commands)
+ *
+ * Admin Command is sent using CSR by setting descriptor and buffer in specific
+ * registers.
+ *
+ * Return: the exit code of the operation.
+ * * - 0 - success.
+ * * - -EIO - CSR mechanism is not enabled.
+ * * - -EBUSY - CSR mechanism is busy.
+ * * - -EINVAL - buf_size is too big or
+ * invalid argument buf or buf_size.
+ * * - -ETIME - Admin Command X command timeout.
+ * * - -EIO - Admin Command X invalid state of HICR register or
+ * Admin Command failed because of bad opcode was returned or
+ * Admin Command failed with error Y.
+ */
+static int ixgbe_aci_send_cmd_execute(struct ixgbe_hw *hw,
+ struct ixgbe_aci_desc *desc,
+ void *buf, u16 buf_size)
+{
+ u16 opcode, buf_tail_size = buf_size % 4;
+ u32 *raw_desc = (u32 *)desc;
+ u32 hicr, i, buf_tail = 0;
+ bool valid_buf = false;
+
+ hw->aci.last_status = IXGBE_ACI_RC_OK;
+
+ /* It's necessary to check if mechanism is enabled */
+ hicr = IXGBE_READ_REG(hw, IXGBE_PF_HICR);
+
+ if (!(hicr & IXGBE_PF_HICR_EN))
+ return -EIO;
+
+ if (hicr & IXGBE_PF_HICR_C)
+ return -EBUSY;
+
+ opcode = desc->opcode;
+
+ if (buf_size > IXGBE_ACI_MAX_BUFFER_SIZE)
+ return -EINVAL;
+
+ if (buf)
+ desc->flags |= IXGBE_ACI_FLAG_BUF;
+
+ if (desc->flags & IXGBE_ACI_FLAG_BUF) {
+ if ((buf && !buf_size) ||
+ (!buf && buf_size))
+ return -EINVAL;
+ if (buf && buf_size)
+ valid_buf = true;
+ }
+
+ if (valid_buf) {
+ if (buf_tail_size)
+ memcpy(&buf_tail, buf + buf_size - buf_tail_size,
+ buf_tail_size);
+
+ if (((buf_size+3) & ~0x3) > IXGBE_ACI_LG_BUF)
+ desc->flags |= IXGBE_ACI_FLAG_LB;
+
+ desc->datalen = buf_size;
+
+ if (desc->flags & IXGBE_ACI_FLAG_RD) {
+ for (i = 0; i < buf_size / 4; i++)
+ IXGBE_WRITE_REG(hw, IXGBE_PF_HIBA(i), ((u32 *)buf)[i]);
+ if (buf_tail_size)
+ IXGBE_WRITE_REG(hw, IXGBE_PF_HIBA(i), buf_tail);
+ }
+ }
+
+ /* Descriptor is written to specific registers */
+ for (i = 0; i < IXGBE_ACI_DESC_SIZE_IN_DWORDS; i++)
+ IXGBE_WRITE_REG(hw, IXGBE_PF_HIDA(i), raw_desc[i]);
+
+ /* SW has to set PF_HICR.C bit and clear PF_HICR.SV and
+ * PF_HICR_EV
+ */
+ hicr = (IXGBE_READ_REG(hw, IXGBE_PF_HICR) | IXGBE_PF_HICR_C) &
+ ~(IXGBE_PF_HICR_SV | IXGBE_PF_HICR_EV);
+ IXGBE_WRITE_REG(hw, IXGBE_PF_HICR, hicr);
+
+#define MAX_SLEEP_RESP_US 1000
+#define MAX_TMOUT_RESP_SYNC_US 100000000
+
+ /* Wait for sync Admin Command response */
+ read_poll_timeout(IXGBE_READ_REG, hicr,
+ (hicr & IXGBE_PF_HICR_SV) ||
+ !(hicr & IXGBE_PF_HICR_C),
+ MAX_SLEEP_RESP_US, MAX_TMOUT_RESP_SYNC_US, true, hw,
+ IXGBE_PF_HICR);
+
+#define MAX_TMOUT_RESP_ASYNC_US 150000000
+
+ /* Wait for async Admin Command response */
+ read_poll_timeout(IXGBE_READ_REG, hicr,
+ (hicr & IXGBE_PF_HICR_EV) ||
+ !(hicr & IXGBE_PF_HICR_C),
+ MAX_SLEEP_RESP_US, MAX_TMOUT_RESP_ASYNC_US, true, hw,
+ IXGBE_PF_HICR);
+
+ /* Read sync Admin Command response */
+ if ((hicr & IXGBE_PF_HICR_SV)) {
+ for (i = 0; i < IXGBE_ACI_DESC_SIZE_IN_DWORDS; i++) {
+ raw_desc[i] = IXGBE_READ_REG(hw, IXGBE_PF_HIDA(i));
+ raw_desc[i] = raw_desc[i];
+ }
+ }
+
+ /* Read async Admin Command response */
+ if ((hicr & IXGBE_PF_HICR_EV) && !(hicr & IXGBE_PF_HICR_C)) {
+ for (i = 0; i < IXGBE_ACI_DESC_SIZE_IN_DWORDS; i++) {
+ raw_desc[i] = IXGBE_READ_REG(hw, IXGBE_PF_HIDA_2(i));
+ raw_desc[i] = raw_desc[i];
+ }
+ }
+
+ /* Handle timeout and invalid state of HICR register */
+ if (hicr & IXGBE_PF_HICR_C)
+ return -ETIME;
+
+ if (!(hicr & IXGBE_PF_HICR_SV) && !(hicr & IXGBE_PF_HICR_EV))
+ return -EIO;
+
+ /* For every command other than 0x0014 treat opcode mismatch
+ * as an error. Response to 0x0014 command read from HIDA_2
+ * is a descriptor of an event which is expected to contain
+ * different opcode than the command.
+ */
+ if (desc->opcode != opcode &&
+ opcode != ixgbe_aci_opc_get_fw_event)
+ return -EIO;
+
+ if (desc->retval) {
+ hw->aci.last_status = (enum ixgbe_aci_err)desc->retval;
+ return -EIO;
+ }
+
+ /* Write a response values to a buf */
+ if (valid_buf) {
+ for (i = 0; i < buf_size / 4; i++)
+ ((u32 *)buf)[i] = IXGBE_READ_REG(hw, IXGBE_PF_HIBA(i));
+ if (buf_tail_size) {
+ buf_tail = IXGBE_READ_REG(hw, IXGBE_PF_HIBA(i));
+ memcpy(buf + buf_size - buf_tail_size, &buf_tail,
+ buf_tail_size);
+ }
+ }
+
+ return 0;
+}
+
+/**
+ * ixgbe_aci_send_cmd - send FW Admin Command to FW Admin Command Interface
+ * @hw: pointer to the HW struct
+ * @desc: descriptor describing the command
+ * @buf: buffer to use for indirect commands (NULL for direct commands)
+ * @buf_size: size of buffer for indirect commands (0 for direct commands)
+ *
+ * Helper function to send FW Admin Commands to the FW Admin Command Interface.
+ *
+ * Retry sending the FW Admin Command multiple times to the FW ACI
+ * if the EBUSY Admin Command error is returned.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_send_cmd(struct ixgbe_hw *hw, struct ixgbe_aci_desc *desc,
+ void *buf, u16 buf_size)
+{
+ u8 idx = 0, *buf_cpy __free(kfree) = NULL;
+ struct ixgbe_aci_desc desc_cpy;
+ enum ixgbe_aci_err last_status;
+ u16 opcode = desc->opcode;
+ bool is_cmd_for_retry;
+ unsigned long timeout;
+ int err;
+
+ is_cmd_for_retry = ixgbe_should_retry_aci_send_cmd_execute(opcode);
+
+ if (is_cmd_for_retry) {
+ if (buf) {
+ buf_cpy = kmalloc(buf_size, GFP_KERNEL);
+ if (!buf_cpy)
+ return -ENOMEM;
+ *buf_cpy = *(u8 *)buf;
+
+ }
+ desc_cpy = *desc;
+ }
+
+ timeout = jiffies + msecs_to_jiffies(IXGBE_ACI_SEND_TIMEOUT_MS);
+ do {
+ mutex_lock(&hw->aci.lock);
+ err = ixgbe_aci_send_cmd_execute(hw, desc, buf, buf_size);
+ last_status = hw->aci.last_status;
+ mutex_unlock(&hw->aci.lock);
+
+ if (!is_cmd_for_retry || !err ||
+ last_status != IXGBE_ACI_RC_EBUSY)
+ break;
+
+ if (buf)
+ memcpy(buf, buf_cpy, buf_size);
+ *desc = desc_cpy;
+
+ msleep(IXGBE_ACI_SEND_DELAY_TIME_MS);
+ } while (++idx < IXGBE_ACI_SEND_MAX_EXECUTE &&
+ time_before(jiffies, timeout));
+
+ return err;
+}
+
+/**
+ * ixgbe_aci_check_event_pending - check if there are any pending events
+ * @hw: pointer to the HW struct
+ *
+ * Determine if there are any pending events.
+ *
+ * Return: true if there are any currently pending events
+ * otherwise false.
+ */
+bool ixgbe_aci_check_event_pending(struct ixgbe_hw *hw)
+{
+ /* Check state of Event Pending (EP) bit */
+ return IXGBE_READ_REG(hw, IXGBE_PF_HICR) & IXGBE_PF_HICR_EP;
+}
+
+/**
+ * ixgbe_aci_get_event - get an event from ACI
+ * @hw: pointer to the HW struct
+ * @e: event information structure
+ * @pending: optional flag signaling that there are more pending events
+ *
+ * Obtain an event from ACI and return its content
+ * through 'e' using ACI command (0x0014).
+ * Provide information if there are more events
+ * to retrieve through 'pending'.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_aci_get_event(struct ixgbe_hw *hw, struct ixgbe_aci_event *e,
+ bool *pending)
+{
+ struct ixgbe_aci_desc desc;
+ int err;
+
+ if (!e || (!e->msg_buf && e->buf_len))
+ return -EINVAL;
+
+ mutex_lock(&hw->aci.lock);
+
+ /* Check if there are any events pending */
+ if (!ixgbe_aci_check_event_pending(hw)) {
+ err = -ENOENT;
+ goto aci_get_event_exit;
+ }
+
+ /* Obtain pending event */
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_get_fw_event);
+ err = ixgbe_aci_send_cmd_execute(hw, &desc, e->msg_buf, e->buf_len);
+ if (err)
+ goto aci_get_event_exit;
+
+ /* Returned 0x0014 opcode indicates that no event was obtained */
+ if (desc.opcode == ixgbe_aci_opc_get_fw_event) {
+ err = -ENOENT;
+ goto aci_get_event_exit;
+ }
+
+ /* Determine size of event data */
+ e->msg_len = min_t(u16, desc.datalen, e->buf_len);
+ /* Write event descriptor to event info structure */
+ memcpy(&e->desc, &desc, sizeof(e->desc));
+
+ /* Check if there are any further events pending */
+ if (pending)
+ *pending = ixgbe_aci_check_event_pending(hw);
+
+aci_get_event_exit:
+ mutex_unlock(&hw->aci.lock);
+
+ return err;
+}
+
+/**
+ * ixgbe_fill_dflt_direct_cmd_desc - fill ACI descriptor with default values.
+ * @desc: pointer to the temp descriptor (non DMA mem)
+ * @opcode: the opcode can be used to decide which flags to turn off or on
+ *
+ * Helper function to fill the descriptor desc with default values
+ * and the provided opcode.
+ */
+void ixgbe_fill_dflt_direct_cmd_desc(struct ixgbe_aci_desc *desc, u16 opcode)
+{
+ /* zero out the desc */
+ memset(desc, 0, sizeof(*desc));
+ desc->opcode = opcode;
+ desc->flags = IXGBE_ACI_FLAG_SI;
+}
+
+/**
+ * ixgbe_aci_req_res - request a common resource
+ * @hw: pointer to the HW struct
+ * @res: resource ID
+ * @access: access type
+ * @sdp_number: resource number
+ * @timeout: the maximum time in ms that the driver may hold the resource
+ *
+ * Requests a common resource using the ACI command (0x0008).
+ * Specifies the maximum time the driver may hold the resource.
+ * If the requested resource is currently occupied by some other driver,
+ * a busy return value is returned and the timeout field value indicates the
+ * maximum time the current owner has to free it.
+ *
+ * Return: the exit code of the operation.
+ */
+static int ixgbe_aci_req_res(struct ixgbe_hw *hw, enum ixgbe_aci_res_ids res,
+ enum ixgbe_aci_res_access_type access,
+ u8 sdp_number, u32 *timeout)
+{
+ struct ixgbe_aci_cmd_req_res *cmd_resp;
+ struct ixgbe_aci_desc desc;
+ int err;
+
+ cmd_resp = &desc.params.res_owner;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_req_res);
+
+ cmd_resp->res_id = res;
+ cmd_resp->access_type = access;
+ cmd_resp->res_number = sdp_number;
+ cmd_resp->timeout = *timeout;
+ *timeout = 0;
+
+ err = ixgbe_aci_send_cmd(hw, &desc, NULL, 0);
+
+ /* If the resource is held by some other driver, the command completes
+ * with a busy return value and the timeout field indicates the maximum
+ * time the current owner of the resource has to free it.
+ */
+ if (!err || hw->aci.last_status == IXGBE_ACI_RC_EBUSY)
+ *timeout = cmd_resp->timeout;
+
+ return err;
+}
+
+/**
+ * ixgbe_aci_release_res - release a common resource using ACI
+ * @hw: pointer to the HW struct
+ * @res: resource ID
+ * @sdp_number: resource number
+ *
+ * Release a common resource using ACI command (0x0009).
+ *
+ * Return: the exit code of the operation.
+ */
+static int ixgbe_aci_release_res(struct ixgbe_hw *hw,
+ enum ixgbe_aci_res_ids res, u8 sdp_number)
+{
+ struct ixgbe_aci_cmd_req_res *cmd;
+ struct ixgbe_aci_desc desc;
+
+ cmd = &desc.params.res_owner;
+
+ ixgbe_fill_dflt_direct_cmd_desc(&desc, ixgbe_aci_opc_release_res);
+
+ cmd->res_id = res;
+ cmd->res_number = sdp_number;
+
+ return ixgbe_aci_send_cmd(hw, &desc, NULL, 0);
+}
+
+/**
+ * ixgbe_acquire_res - acquire the ownership of a resource
+ * @hw: pointer to the HW structure
+ * @res: resource ID
+ * @access: access type (read or write)
+ * @timeout: timeout in milliseconds
+ *
+ * Make an attempt to acquire the ownership of a resource using
+ * the ixgbe_aci_req_res to utilize ACI.
+ * In case if some other driver has previously acquired the resource and
+ * performed any necessary updates, the -EALREADY is returned,
+ * and the caller does not obtain the resource and has no further work to do.
+ * If needed, the function will poll until the current lock owner timeouts.
+ *
+ * Return: the exit code of the operation.
+ */
+int ixgbe_acquire_res(struct ixgbe_hw *hw, enum ixgbe_aci_res_ids res,
+ enum ixgbe_aci_res_access_type access, u32 timeout)
+{
+#define IXGBE_RES_POLLING_DELAY_MS 10
+ u32 delay = IXGBE_RES_POLLING_DELAY_MS;
+ u32 res_timeout = timeout;
+ u32 retry_timeout;
+ int err;
+
+ err = ixgbe_aci_req_res(hw, res, access, 0, &res_timeout);
+
+ /* A return code of -EALREADY means that another driver has
+ * previously acquired the resource and performed any necessary updates;
+ * in this case the caller does not obtain the resource and has no
+ * further work to do.
+ */
+ if (err == -EALREADY)
+ return err;
+
+ /* If necessary, poll until the current lock owner timeouts.
+ * Set retry_timeout to the timeout value reported by the FW in the
+ * response to the "Request Resource Ownership" (0x0008) Admin Command
+ * as it indicates the maximum time the current owner of the resource
+ * is allowed to hold it.
+ */
+ retry_timeout = res_timeout;
+ while (err && retry_timeout && res_timeout) {
+ msleep(delay);
+ retry_timeout = (retry_timeout > delay) ?
+ retry_timeout - delay : 0;
+ err = ixgbe_aci_req_res(hw, res, access, 0, &res_timeout);
+
+ /* success - lock acquired
+ * -EALREADY - lock free, no work to do
+ */
+ if (!err || err == -EALREADY)
+ break;
+ }
+
+ return err;
+}
+
+/**
+ * ixgbe_release_res - release a common resource
+ * @hw: pointer to the HW structure
+ * @res: resource ID
+ *
+ * Release a common resource using ixgbe_aci_release_res.
+ */
+void ixgbe_release_res(struct ixgbe_hw *hw, enum ixgbe_aci_res_ids res)
+{
+ u32 total_delay = 0;
+ int err;
+
+ err = ixgbe_aci_release_res(hw, res, 0);
+
+ /* There are some rare cases when trying to release the resource
+ * results in an admin command timeout, so handle them correctly.
+ */
+ while (err == -ETIME &&
+ total_delay < IXGBE_ACI_RELEASE_RES_TIMEOUT) {
+ usleep_range(1000, 1500);
+ err = ixgbe_aci_release_res(hw, res, 0);
+ total_delay++;
+ }
+}
new file mode 100644
@@ -0,0 +1,19 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright(c) 1999 - 2024 Intel Corporation. */
+
+#ifndef _IXGBE_E610_H_
+#define _IXGBE_E610_H_
+
+#include "ixgbe_type.h"
+
+int ixgbe_aci_send_cmd(struct ixgbe_hw *hw, struct ixgbe_aci_desc *desc,
+ void *buf, u16 buf_size);
+bool ixgbe_aci_check_event_pending(struct ixgbe_hw *hw);
+int ixgbe_aci_get_event(struct ixgbe_hw *hw, struct ixgbe_aci_event *e,
+ bool *pending);
+void ixgbe_fill_dflt_direct_cmd_desc(struct ixgbe_aci_desc *desc, u16 opcode);
+int ixgbe_acquire_res(struct ixgbe_hw *hw, enum ixgbe_aci_res_ids res,
+ enum ixgbe_aci_res_access_type access, u32 timeout);
+void ixgbe_release_res(struct ixgbe_hw *hw, enum ixgbe_aci_res_ids res);
+
+#endif /* _IXGBE_E610_H_ */
@@ -1,5 +1,5 @@
/* SPDX-License-Identifier: GPL-2.0 */
-/* Copyright(c) 1999 - 2018 Intel Corporation. */
+/* Copyright(c) 1999 - 2024 Intel Corporation. */
#ifndef _IXGBE_TYPE_H_
#define _IXGBE_TYPE_H_
@@ -7,6 +7,7 @@
#include <linux/types.h>
#include <linux/mdio.h>
#include <linux/netdevice.h>
+#include "ixgbe_type_e610.h"
/* Device IDs */
#define IXGBE_DEV_ID_82598 0x10B6
@@ -71,12 +72,19 @@
#define IXGBE_DEV_ID_X550EM_A_1G_T 0x15E4
#define IXGBE_DEV_ID_X550EM_A_1G_T_L 0x15E5
+#define IXGBE_DEV_ID_E610_BACKPLANE 0x57AE
+#define IXGBE_DEV_ID_E610_SFP 0x57AF
+#define IXGBE_DEV_ID_E610_10G_T 0x57B0
+#define IXGBE_DEV_ID_E610_2_5G_T 0x57B1
+#define IXGBE_DEV_ID_E610_SGMII 0x57B2
+
/* VF Device IDs */
#define IXGBE_DEV_ID_82599_VF 0x10ED
#define IXGBE_DEV_ID_X540_VF 0x1515
#define IXGBE_DEV_ID_X550_VF 0x1565
#define IXGBE_DEV_ID_X550EM_X_VF 0x15A8
#define IXGBE_DEV_ID_X550EM_A_VF 0x15C5
+#define IXGBE_DEV_ID_E610_VF 0x57AD
#define IXGBE_CAT(r, m) IXGBE_##r##_##m
@@ -1600,7 +1608,7 @@ enum {
#define IXGBE_EICR_PCI 0x00040000 /* PCI Exception */
#define IXGBE_EICR_MAILBOX 0x00080000 /* VF to PF Mailbox Interrupt */
#define IXGBE_EICR_LSC 0x00100000 /* Link Status Change */
-#define IXGBE_EICR_LINKSEC 0x00200000 /* PN Threshold */
+#define IXGBE_EICR_FW_EVENT 0x00200000 /* Async FW event */
#define IXGBE_EICR_MNG 0x00400000 /* Manageability Event Interrupt */
#define IXGBE_EICR_TS 0x00800000 /* Thermal Sensor Event */
#define IXGBE_EICR_TIMESYNC 0x01000000 /* Timesync Event */
@@ -1636,6 +1644,7 @@ enum {
#define IXGBE_EICS_PCI IXGBE_EICR_PCI /* PCI Exception */
#define IXGBE_EICS_MAILBOX IXGBE_EICR_MAILBOX /* VF to PF Mailbox Int */
#define IXGBE_EICS_LSC IXGBE_EICR_LSC /* Link Status Change */
+#define IXGBE_EICS_FW_EVENT IXGBE_EICR_FW_EVENT /* Async FW event */
#define IXGBE_EICS_MNG IXGBE_EICR_MNG /* MNG Event Interrupt */
#define IXGBE_EICS_TIMESYNC IXGBE_EICR_TIMESYNC /* Timesync Event */
#define IXGBE_EICS_GPI_SDP0(_hw) IXGBE_EICR_GPI_SDP0(_hw)
@@ -1654,6 +1663,7 @@ enum {
#define IXGBE_EIMS_PCI IXGBE_EICR_PCI /* PCI Exception */
#define IXGBE_EIMS_MAILBOX IXGBE_EICR_MAILBOX /* VF to PF Mailbox Int */
#define IXGBE_EIMS_LSC IXGBE_EICR_LSC /* Link Status Change */
+#define IXGBE_EIMS_FW_EVENT IXGBE_EICR_FW_EVENT /* Async FW event */
#define IXGBE_EIMS_MNG IXGBE_EICR_MNG /* MNG Event Interrupt */
#define IXGBE_EIMS_TS IXGBE_EICR_TS /* Thermel Sensor Event */
#define IXGBE_EIMS_TIMESYNC IXGBE_EICR_TIMESYNC /* Timesync Event */
@@ -1673,6 +1683,7 @@ enum {
#define IXGBE_EIMC_PCI IXGBE_EICR_PCI /* PCI Exception */
#define IXGBE_EIMC_MAILBOX IXGBE_EICR_MAILBOX /* VF to PF Mailbox Int */
#define IXGBE_EIMC_LSC IXGBE_EICR_LSC /* Link Status Change */
+#define IXGBE_EIMC_FW_EVENT IXGBE_EICR_FW_EVENT /* Async FW event */
#define IXGBE_EIMC_MNG IXGBE_EICR_MNG /* MNG Event Interrupt */
#define IXGBE_EIMC_TIMESYNC IXGBE_EICR_TIMESYNC /* Timesync Event */
#define IXGBE_EIMC_GPI_SDP0(_hw) IXGBE_EICR_GPI_SDP0(_hw)
@@ -2068,6 +2079,7 @@ enum {
#define IXGBE_SAN_MAC_ADDR_PTR 0x28
#define IXGBE_DEVICE_CAPS 0x2C
#define IXGBE_SERIAL_NUMBER_MAC_ADDR 0x11
+#define IXGBE_PCIE_MSIX_E610_CAPS 0xB2
#define IXGBE_PCIE_MSIX_82599_CAPS 0x72
#define IXGBE_MAX_MSIX_VECTORS_82599 0x40
#define IXGBE_PCIE_MSIX_82598_CAPS 0x62
@@ -2289,6 +2301,7 @@ enum {
#define IXGBE_RXMTRL_V2_MGMT_MSG 0x0D00
#define IXGBE_FCTRL_SBP 0x00000002 /* Store Bad Packet */
+#define IXGBE_FCTRL_TPE 0x00000080 /* Tag Promiscuous Ena*/
#define IXGBE_FCTRL_MPE 0x00000100 /* Multicast Promiscuous Ena*/
#define IXGBE_FCTRL_UPE 0x00000200 /* Unicast Promiscuous Ena */
#define IXGBE_FCTRL_BAM 0x00000400 /* Broadcast Accept Mode */
@@ -2352,6 +2365,7 @@ enum {
/* Multiple Transmit Queue Command Register */
#define IXGBE_MTQC_RT_ENA 0x1 /* DCB Enable */
#define IXGBE_MTQC_VT_ENA 0x2 /* VMDQ2 Enable */
+#define IXGBE_MTQC_NUM_TC_OR_Q 0xC /* Number of TCs or TxQs per pool */
#define IXGBE_MTQC_64Q_1PB 0x0 /* 64 queues 1 pack buffer */
#define IXGBE_MTQC_32VF 0x8 /* 4 TX Queues per pool w/32VF's */
#define IXGBE_MTQC_64VF 0x4 /* 2 TX Queues per pool w/64VF's */
@@ -2971,6 +2985,29 @@ typedef u32 ixgbe_link_speed;
IXGBE_LINK_SPEED_1GB_FULL | \
IXGBE_LINK_SPEED_10GB_FULL)
+/* Physical layer type */
+typedef u64 ixgbe_physical_layer;
+#define IXGBE_PHYSICAL_LAYER_UNKNOWN 0
+#define IXGBE_PHYSICAL_LAYER_10GBASE_T 0x00001
+#define IXGBE_PHYSICAL_LAYER_1000BASE_T 0x00002
+#define IXGBE_PHYSICAL_LAYER_100BASE_TX 0x00004
+#define IXGBE_PHYSICAL_LAYER_SFP_PLUS_CU 0x00008
+#define IXGBE_PHYSICAL_LAYER_10GBASE_LR 0x00010
+#define IXGBE_PHYSICAL_LAYER_10GBASE_LRM 0x00020
+#define IXGBE_PHYSICAL_LAYER_10GBASE_SR 0x00040
+#define IXGBE_PHYSICAL_LAYER_10GBASE_KX4 0x00080
+#define IXGBE_PHYSICAL_LAYER_10GBASE_CX4 0x00100
+#define IXGBE_PHYSICAL_LAYER_1000BASE_KX 0x00200
+#define IXGBE_PHYSICAL_LAYER_1000BASE_BX 0x00400
+#define IXGBE_PHYSICAL_LAYER_10GBASE_KR 0x00800
+#define IXGBE_PHYSICAL_LAYER_10GBASE_XAUI 0x01000
+#define IXGBE_PHYSICAL_LAYER_SFP_ACTIVE_DA 0x02000
+#define IXGBE_PHYSICAL_LAYER_1000BASE_SX 0x04000
+#define IXGBE_PHYSICAL_LAYER_10BASE_T 0x08000
+#define IXGBE_PHYSICAL_LAYER_2500BASE_KX 0x10000
+#define IXGBE_PHYSICAL_LAYER_2500BASE_T 0x20000
+#define IXGBE_PHYSICAL_LAYER_5000BASE_T 0x40000
+
/* Flow Control Data Sheet defined values
* Calculation and defines taken from 802.1bb Annex O
*/
@@ -3146,6 +3183,8 @@ enum ixgbe_mac_type {
ixgbe_mac_X550,
ixgbe_mac_X550EM_x,
ixgbe_mac_x550em_a,
+ ixgbe_mac_e610,
+ ixgbe_mac_e610_vf,
ixgbe_num_macs
};
@@ -3225,7 +3264,9 @@ enum ixgbe_media_type {
ixgbe_media_type_copper,
ixgbe_media_type_backplane,
ixgbe_media_type_cx4,
- ixgbe_media_type_virtual
+ ixgbe_media_type_virtual,
+ ixgbe_media_type_da,
+ ixgbe_media_type_aui,
};
/* Flow Control Settings */
@@ -3234,7 +3275,8 @@ enum ixgbe_fc_mode {
ixgbe_fc_rx_pause,
ixgbe_fc_tx_pause,
ixgbe_fc_full,
- ixgbe_fc_default
+ ixgbe_fc_default,
+ ixgbe_fc_pfc,
};
/* Smart Speed Settings */
@@ -3534,6 +3576,9 @@ struct ixgbe_link_operations {
struct ixgbe_link_info {
struct ixgbe_link_operations ops;
u8 addr;
+ struct ixgbe_link_status link_info;
+ struct ixgbe_link_status link_info_old;
+ u8 get_link_info;
};
struct ixgbe_eeprom_info {
@@ -3576,6 +3621,7 @@ struct ixgbe_mac_info {
u8 san_mac_rar_index;
struct ixgbe_thermal_sensor_data thermal_sensor_data;
bool set_lben;
+ u32 max_link_up_time;
u8 led_link_act;
};
@@ -3600,6 +3646,10 @@ struct ixgbe_phy_info {
bool reset_if_overtemp;
bool qsfp_shared_i2c_bus;
u32 nw_mng_if_sel;
+ u64 phy_type_low;
+ u64 phy_type_high;
+ u16 curr_user_speed_req;
+ struct ixgbe_aci_cmd_set_phy_cfg_data curr_user_phy_cfg;
};
#include "ixgbe_mbx.h"
@@ -3655,6 +3705,19 @@ struct ixgbe_hw {
bool allow_unsupported_sfp;
bool wol_enabled;
bool need_crosstalk_fix;
+ u8 api_branch;
+ u8 api_maj_ver;
+ u8 api_min_ver;
+ u8 api_patch;
+ u8 fw_branch;
+ u8 fw_maj_ver;
+ u8 fw_min_ver;
+ u8 fw_patch;
+ u32 fw_build;
+ struct ixgbe_aci_info aci;
+ struct ixgbe_flash_info flash;
+ struct ixgbe_hw_dev_caps dev_caps;
+ struct ixgbe_hw_func_caps func_caps;
};
struct ixgbe_info {
new file mode 100644
@@ -0,0 +1,1063 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/* Copyright(c) 1999 - 2024 Intel Corporation. */
+
+#ifndef _IXGBE_TYPE_E610_H_
+#define _IXGBE_TYPE_E610_H_
+
+#define BYTES_PER_DWORD 4
+
+/* General E610 defines */
+#define IXGBE_MAX_VSI 768
+
+/* Checksum and Shadow RAM pointers */
+#define E610_SR_SW_CHECKSUM_WORD 0x3F
+
+/* Flash Access Register */
+#define IXGBE_GLNVM_FLA 0x000B6108 /* Reset Source: POR */
+#define IXGBE_GLNVM_FLA_LOCKED_S 6
+#define IXGBE_GLNVM_FLA_LOCKED_M BIT(6)
+
+/* Admin Command Interface (ACI) registers */
+#define IXGBE_PF_HIDA(_i) (0x00085000 + ((_i) * 4))
+#define IXGBE_PF_HIDA_2(_i) (0x00085020 + ((_i) * 4))
+#define IXGBE_PF_HIBA(_i) (0x00084000 + ((_i) * 4))
+#define IXGBE_PF_HICR 0x00082048
+
+#define IXGBE_PF_HICR_EN BIT(0)
+#define IXGBE_PF_HICR_C BIT(1)
+#define IXGBE_PF_HICR_SV BIT(2)
+#define IXGBE_PF_HICR_EV BIT(3)
+#define IXGBE_PF_HICR_EP BIT(4)
+
+#define IXGBE_ACI_DESC_SIZE 32
+#define IXGBE_ACI_DESC_SIZE_IN_DWORDS (IXGBE_ACI_DESC_SIZE / BYTES_PER_DWORD)
+
+#define IXGBE_ACI_MAX_BUFFER_SIZE 4096 /* Size in bytes */
+#define IXGBE_ACI_SEND_DELAY_TIME_MS 10
+#define IXGBE_ACI_SEND_MAX_EXECUTE 3
+#define IXGBE_ACI_SEND_TIMEOUT_MS \
+ (IXGBE_ACI_SEND_MAX_EXECUTE * IXGBE_ACI_SEND_DELAY_TIME_MS)
+/* [ms] timeout of waiting for sync response */
+#define IXGBE_ACI_SYNC_RESPONSE_TIMEOUT 100000
+/* [ms] timeout of waiting for async response */
+#define IXGBE_ACI_ASYNC_RESPONSE_TIMEOUT 150000
+/* [ms] timeout of waiting for resource release */
+#define IXGBE_ACI_RELEASE_RES_TIMEOUT 10000
+
+/* FW defined boundary for a large buffer, 4k >= Large buffer > 512 bytes */
+#define IXGBE_ACI_LG_BUF 512
+
+/* Flags sub-structure
+ * |0 |1 |2 |3 |4 |5 |6 |7 |8 |9 |10 |11 |12 |13 |14 |15 |
+ * |DD |CMP|ERR|VFE| * * RESERVED * * |LB |RD |VFC|BUF|SI |EI |FE |
+ */
+
+#define IXGBE_ACI_FLAG_DD BIT(0) /* 0x1 */
+#define IXGBE_ACI_FLAG_CMP BIT(1) /* 0x2 */
+#define IXGBE_ACI_FLAG_ERR BIT(2) /* 0x4 */
+#define IXGBE_ACI_FLAG_VFE BIT(3) /* 0x8 */
+#define IXGBE_ACI_FLAG_LB BIT(9) /* 0x200 */
+#define IXGBE_ACI_FLAG_RD BIT(10) /* 0x400 */
+#define IXGBE_ACI_FLAG_VFC BIT(11) /* 0x800 */
+#define IXGBE_ACI_FLAG_BUF BIT(12) /* 0x1000 */
+#define IXGBE_ACI_FLAG_SI BIT(13) /* 0x2000 */
+#define IXGBE_ACI_FLAG_EI BIT(14) /* 0x4000 */
+#define IXGBE_ACI_FLAG_FE BIT(15) /* 0x8000 */
+
+/* Admin Command Interface (ACI) error codes */
+enum ixgbe_aci_err {
+ IXGBE_ACI_RC_OK = 0, /* Success */
+ IXGBE_ACI_RC_EPERM = 1, /* Operation not permitted */
+ IXGBE_ACI_RC_ENOENT = 2, /* No such element */
+ IXGBE_ACI_RC_ESRCH = 3, /* Bad opcode */
+ IXGBE_ACI_RC_EINTR = 4, /* Operation interrupted */
+ IXGBE_ACI_RC_EIO = 5, /* I/O error */
+ IXGBE_ACI_RC_ENXIO = 6, /* No such resource */
+ IXGBE_ACI_RC_E2BIG = 7, /* Arg too long */
+ IXGBE_ACI_RC_EAGAIN = 8, /* Try again */
+ IXGBE_ACI_RC_ENOMEM = 9, /* Out of memory */
+ IXGBE_ACI_RC_EACCES = 10, /* Permission denied */
+ IXGBE_ACI_RC_EFAULT = 11, /* Bad address */
+ IXGBE_ACI_RC_EBUSY = 12, /* Device or resource busy */
+ IXGBE_ACI_RC_EEXIST = 13, /* Object already exists */
+ IXGBE_ACI_RC_EINVAL = 14, /* Invalid argument */
+ IXGBE_ACI_RC_ENOTTY = 15, /* Not a typewriter */
+ IXGBE_ACI_RC_ENOSPC = 16, /* No space left or alloc failure */
+ IXGBE_ACI_RC_ENOSYS = 17, /* Function not implemented */
+ IXGBE_ACI_RC_ERANGE = 18, /* Parameter out of range */
+ IXGBE_ACI_RC_EFLUSHED = 19, /* Cmd flushed due to prev cmd error */
+ IXGBE_ACI_RC_BAD_ADDR = 20, /* Descriptor contains a bad pointer */
+ IXGBE_ACI_RC_EMODE = 21, /* Op not allowed in current dev mode */
+ IXGBE_ACI_RC_EFBIG = 22, /* File too big */
+ IXGBE_ACI_RC_ESBCOMP = 23, /* SB-IOSF completion unsuccessful */
+ IXGBE_ACI_RC_ENOSEC = 24, /* Missing security manifest */
+ IXGBE_ACI_RC_EBADSIG = 25, /* Bad RSA signature */
+ IXGBE_ACI_RC_ESVN = 26, /* SVN number prohibits this package */
+ IXGBE_ACI_RC_EBADMAN = 27, /* Manifest hash mismatch */
+ IXGBE_ACI_RC_EBADBUF = 28, /* Buffer hash mismatches manifest */
+ IXGBE_ACI_RC_EACCES_BMCU = 29, /* BMC Update in progress */
+};
+
+/* Admin Command Interface (ACI) opcodes */
+enum ixgbe_aci_opc {
+ ixgbe_aci_opc_get_ver = 0x0001,
+ ixgbe_aci_opc_driver_ver = 0x0002,
+ ixgbe_aci_opc_get_exp_err = 0x0005,
+
+ /* resource ownership */
+ ixgbe_aci_opc_req_res = 0x0008,
+ ixgbe_aci_opc_release_res = 0x0009,
+
+ /* device/function capabilities */
+ ixgbe_aci_opc_list_func_caps = 0x000A,
+ ixgbe_aci_opc_list_dev_caps = 0x000B,
+
+ /* safe disable of RXEN */
+ ixgbe_aci_opc_disable_rxen = 0x000C,
+
+ /* FW events */
+ ixgbe_aci_opc_get_fw_event = 0x0014,
+
+ /* PHY commands */
+ ixgbe_aci_opc_get_phy_caps = 0x0600,
+ ixgbe_aci_opc_set_phy_cfg = 0x0601,
+ ixgbe_aci_opc_restart_an = 0x0605,
+ ixgbe_aci_opc_get_link_status = 0x0607,
+ ixgbe_aci_opc_set_event_mask = 0x0613,
+ ixgbe_aci_opc_get_link_topo = 0x06E0,
+ ixgbe_aci_opc_get_link_topo_pin = 0x06E1,
+ ixgbe_aci_opc_read_i2c = 0x06E2,
+ ixgbe_aci_opc_write_i2c = 0x06E3,
+ ixgbe_aci_opc_read_mdio = 0x06E4,
+ ixgbe_aci_opc_write_mdio = 0x06E5,
+ ixgbe_aci_opc_set_gpio_by_func = 0x06E6,
+ ixgbe_aci_opc_get_gpio_by_func = 0x06E7,
+ ixgbe_aci_opc_set_gpio = 0x06EC,
+ ixgbe_aci_opc_get_gpio = 0x06ED,
+ ixgbe_aci_opc_sff_eeprom = 0x06EE,
+ ixgbe_aci_opc_prog_topo_dev_nvm = 0x06F2,
+ ixgbe_aci_opc_read_topo_dev_nvm = 0x06F3,
+
+ /* NVM commands */
+ ixgbe_aci_opc_nvm_read = 0x0701,
+ ixgbe_aci_opc_nvm_erase = 0x0702,
+ ixgbe_aci_opc_nvm_write = 0x0703,
+ ixgbe_aci_opc_nvm_cfg_read = 0x0704,
+ ixgbe_aci_opc_nvm_cfg_write = 0x0705,
+ ixgbe_aci_opc_nvm_checksum = 0x0706,
+ ixgbe_aci_opc_nvm_write_activate = 0x0707,
+ ixgbe_aci_opc_nvm_sr_dump = 0x0707,
+ ixgbe_aci_opc_nvm_save_factory_settings = 0x0708,
+ ixgbe_aci_opc_nvm_update_empr = 0x0709,
+ ixgbe_aci_opc_nvm_pkg_data = 0x070A,
+ ixgbe_aci_opc_nvm_pass_component_tbl = 0x070B,
+
+ /* Alternate Structure Commands */
+ ixgbe_aci_opc_write_alt_direct = 0x0900,
+ ixgbe_aci_opc_write_alt_indirect = 0x0901,
+ ixgbe_aci_opc_read_alt_direct = 0x0902,
+ ixgbe_aci_opc_read_alt_indirect = 0x0903,
+ ixgbe_aci_opc_done_alt_write = 0x0904,
+ ixgbe_aci_opc_clear_port_alt_write = 0x0906,
+
+ /* debug commands */
+ ixgbe_aci_opc_debug_dump_internals = 0xFF08,
+
+ /* SystemDiagnostic commands */
+ ixgbe_aci_opc_set_health_status_config = 0xFF20,
+ ixgbe_aci_opc_get_supported_health_status_codes = 0xFF21,
+ ixgbe_aci_opc_get_health_status = 0xFF22,
+ ixgbe_aci_opc_clear_health_status = 0xFF23,
+};
+
+/* Get version (direct 0x0001) */
+struct ixgbe_aci_cmd_get_ver {
+ u32 rom_ver;
+ u32 fw_build;
+ u8 fw_branch;
+ u8 fw_major;
+ u8 fw_minor;
+ u8 fw_patch;
+ u8 api_branch;
+ u8 api_major;
+ u8 api_minor;
+ u8 api_patch;
+};
+
+#define IXGBE_DRV_VER_STR_LEN_E610 32
+
+/* Send driver version (indirect 0x0002) */
+struct ixgbe_aci_cmd_driver_ver {
+ u8 major_ver;
+ u8 minor_ver;
+ u8 build_ver;
+ u8 subbuild_ver;
+ u8 reserved[4];
+ u32 addr_high;
+ u32 addr_low;
+};
+
+/* Get Expanded Error Code (0x0005, direct) */
+struct ixgbe_aci_cmd_get_exp_err {
+ u32 reason;
+#define IXGBE_ACI_EXPANDED_ERROR_NOT_PROVIDED 0xFFFFFFFF
+ u32 identifier;
+ u8 rsvd[8];
+};
+
+/* FW update timeout definitions are in milliseconds */
+#define IXGBE_NVM_TIMEOUT 180000
+
+enum ixgbe_aci_res_access_type {
+ IXGBE_RES_READ = 1,
+ IXGBE_RES_WRITE
+};
+
+enum ixgbe_aci_res_ids {
+ IXGBE_NVM_RES_ID = 1,
+ IXGBE_SPD_RES_ID,
+ IXGBE_CHANGE_LOCK_RES_ID,
+ IXGBE_GLOBAL_CFG_LOCK_RES_ID
+};
+
+/* Request resource ownership (direct 0x0008)
+ * Release resource ownership (direct 0x0009)
+ */
+struct ixgbe_aci_cmd_req_res {
+ u16 res_id;
+ u16 access_type;
+
+ /* Upon successful completion, FW writes this value and driver is
+ * expected to release resource before timeout. This value is provided
+ * in milliseconds.
+ */
+ u32 timeout;
+#define IXGBE_ACI_RES_NVM_READ_DFLT_TIMEOUT_MS 3000
+#define IXGBE_ACI_RES_NVM_WRITE_DFLT_TIMEOUT_MS 180000
+#define IXGBE_ACI_RES_CHNG_LOCK_DFLT_TIMEOUT_MS 1000
+#define IXGBE_ACI_RES_GLBL_LOCK_DFLT_TIMEOUT_MS 3000
+ /* For SDP: pin ID of the SDP */
+ u32 res_number;
+ u16 status;
+#define IXGBE_ACI_RES_GLBL_SUCCESS 0
+#define IXGBE_ACI_RES_GLBL_IN_PROG 1
+#define IXGBE_ACI_RES_GLBL_DONE 2
+ u8 reserved[2];
+};
+
+/* Get function capabilities (indirect 0x000A)
+ * Get device capabilities (indirect 0x000B)
+ */
+struct ixgbe_aci_cmd_list_caps {
+ u8 cmd_flags;
+ u8 pf_index;
+ u8 reserved[2];
+ u32 count;
+ u32 addr_high;
+ u32 addr_low;
+};
+
+/* Device/Function buffer entry, repeated per reported capability */
+struct ixgbe_aci_cmd_list_caps_elem {
+ u16 cap;
+#define IXGBE_ACI_CAPS_VALID_FUNCTIONS 0x0005
+#define IXGBE_ACI_MAX_VALID_FUNCTIONS 0x8
+#define IXGBE_ACI_CAPS_SRIOV 0x0012
+#define IXGBE_ACI_CAPS_VF 0x0013
+#define IXGBE_ACI_CAPS_VMDQ 0x0014
+#define IXGBE_ACI_CAPS_VSI 0x0017
+#define IXGBE_ACI_CAPS_DCB 0x0018
+#define IXGBE_ACI_CAPS_RSS 0x0040
+#define IXGBE_ACI_CAPS_RXQS 0x0041
+#define IXGBE_ACI_CAPS_TXQS 0x0042
+#define IXGBE_ACI_CAPS_MSIX 0x0043
+#define IXGBE_ACI_CAPS_FD 0x0045
+#define IXGBE_ACI_CAPS_1588 0x0046
+#define IXGBE_ACI_CAPS_MAX_MTU 0x0047
+#define IXGBE_ACI_CAPS_NVM_VER 0x0048
+#define IXGBE_ACI_CAPS_PENDING_NVM_VER 0x0049
+#define IXGBE_ACI_CAPS_OROM_VER 0x004A
+#define IXGBE_ACI_CAPS_PENDING_OROM_VER 0x004B
+#define IXGBE_ACI_CAPS_PENDING_NET_VER 0x004D
+#define IXGBE_ACI_CAPS_INLINE_IPSEC 0x0070
+#define IXGBE_ACI_CAPS_NUM_ENABLED_PORTS 0x0072
+#define IXGBE_ACI_CAPS_PCIE_RESET_AVOIDANCE 0x0076
+#define IXGBE_ACI_CAPS_POST_UPDATE_RESET_RESTRICT 0x0077
+#define IXGBE_ACI_CAPS_NVM_MGMT 0x0080
+#define IXGBE_ACI_CAPS_EXT_TOPO_DEV_IMG0 0x0081
+#define IXGBE_ACI_CAPS_EXT_TOPO_DEV_IMG1 0x0082
+#define IXGBE_ACI_CAPS_EXT_TOPO_DEV_IMG2 0x0083
+#define IXGBE_ACI_CAPS_EXT_TOPO_DEV_IMG3 0x0084
+ u8 major_ver;
+ u8 minor_ver;
+ /* Number of resources described by this capability */
+ u32 number;
+ /* Only meaningful for some types of resources */
+ u32 logical_id;
+ /* Only meaningful for some types of resources */
+ u32 phys_id;
+ u64 rsvd1;
+ u64 rsvd2;
+};
+
+/* Disable RXEN (direct 0x000C) */
+struct ixgbe_aci_cmd_disable_rxen {
+ u8 lport_num;
+ u8 reserved[15];
+};
+
+/* Get PHY capabilities (indirect 0x0600) */
+struct ixgbe_aci_cmd_get_phy_caps {
+ u8 lport_num;
+ u8 reserved;
+ u16 param0;
+ /* 18.0 - Report qualified modules */
+#define IXGBE_ACI_GET_PHY_RQM BIT(0)
+ /* 18.1 - 18.3 : Report mode
+ * 000b - Report topology capabilities, without media
+ * 001b - Report topology capabilities, with media
+ * 010b - Report Active configuration
+ * 011b - Report PHY Type and FEC mode capabilities
+ * 100b - Report Default capabilities
+ */
+#define IXGBE_ACI_REPORT_MODE_M GENMASK(3, 1)
+#define IXGBE_ACI_REPORT_TOPO_CAP_NO_MEDIA 0
+#define IXGBE_ACI_REPORT_TOPO_CAP_MEDIA BIT(1)
+#define IXGBE_ACI_REPORT_ACTIVE_CFG BIT(2)
+#define IXGBE_ACI_REPORT_DFLT_CFG BIT(3)
+ u32 reserved1;
+ u32 addr_high;
+ u32 addr_low;
+};
+
+/* This is #define of PHY type (Extended):
+ * The first set of defines is for phy_type_low.
+ */
+#define IXGBE_PHY_TYPE_LOW_100BASE_TX BIT_ULL(0)
+#define IXGBE_PHY_TYPE_LOW_100M_SGMII BIT_ULL(1)
+#define IXGBE_PHY_TYPE_LOW_1000BASE_T BIT_ULL(2)
+#define IXGBE_PHY_TYPE_LOW_1000BASE_SX BIT_ULL(3)
+#define IXGBE_PHY_TYPE_LOW_1000BASE_LX BIT_ULL(4)
+#define IXGBE_PHY_TYPE_LOW_1000BASE_KX BIT_ULL(5)
+#define IXGBE_PHY_TYPE_LOW_1G_SGMII BIT_ULL(6)
+#define IXGBE_PHY_TYPE_LOW_2500BASE_T BIT_ULL(7)
+#define IXGBE_PHY_TYPE_LOW_2500BASE_X BIT_ULL(8)
+#define IXGBE_PHY_TYPE_LOW_2500BASE_KX BIT_ULL(9)
+#define IXGBE_PHY_TYPE_LOW_5GBASE_T BIT_ULL(10)
+#define IXGBE_PHY_TYPE_LOW_5GBASE_KR BIT_ULL(11)
+#define IXGBE_PHY_TYPE_LOW_10GBASE_T BIT_ULL(12)
+#define IXGBE_PHY_TYPE_LOW_10G_SFI_DA BIT_ULL(13)
+#define IXGBE_PHY_TYPE_LOW_10GBASE_SR BIT_ULL(14)
+#define IXGBE_PHY_TYPE_LOW_10GBASE_LR BIT_ULL(15)
+#define IXGBE_PHY_TYPE_LOW_10GBASE_KR_CR1 BIT_ULL(16)
+#define IXGBE_PHY_TYPE_LOW_10G_SFI_AOC_ACC BIT_ULL(17)
+#define IXGBE_PHY_TYPE_LOW_10G_SFI_C2C BIT_ULL(18)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_T BIT_ULL(19)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_CR BIT_ULL(20)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_CR_S BIT_ULL(21)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_CR1 BIT_ULL(22)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_SR BIT_ULL(23)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_LR BIT_ULL(24)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_KR BIT_ULL(25)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_KR_S BIT_ULL(26)
+#define IXGBE_PHY_TYPE_LOW_25GBASE_KR1 BIT_ULL(27)
+#define IXGBE_PHY_TYPE_LOW_25G_AUI_AOC_ACC BIT_ULL(28)
+#define IXGBE_PHY_TYPE_LOW_25G_AUI_C2C BIT_ULL(29)
+#define IXGBE_PHY_TYPE_LOW_MAX_INDEX 29
+/* The second set of defines is for phy_type_high. */
+#define IXGBE_PHY_TYPE_HIGH_10BASE_T BIT_ULL(1)
+#define IXGBE_PHY_TYPE_HIGH_10M_SGMII BIT_ULL(2)
+#define IXGBE_PHY_TYPE_HIGH_2500M_SGMII BIT_ULL(56)
+#define IXGBE_PHY_TYPE_HIGH_100M_USXGMII BIT_ULL(57)
+#define IXGBE_PHY_TYPE_HIGH_1G_USXGMII BIT_ULL(58)
+#define IXGBE_PHY_TYPE_HIGH_2500M_USXGMII BIT_ULL(59)
+#define IXGBE_PHY_TYPE_HIGH_5G_USXGMII BIT_ULL(60)
+#define IXGBE_PHY_TYPE_HIGH_10G_USXGMII BIT_ULL(61)
+#define IXGBE_PHY_TYPE_HIGH_MAX_INDEX 61
+
+struct ixgbe_aci_cmd_get_phy_caps_data {
+ u64 phy_type_low; /* Use values from IXGBE_PHY_TYPE_LOW_* */
+ u64 phy_type_high; /* Use values from IXGBE_PHY_TYPE_HIGH_* */
+ u8 caps;
+#define IXGBE_ACI_PHY_EN_TX_LINK_PAUSE BIT(0)
+#define IXGBE_ACI_PHY_EN_RX_LINK_PAUSE BIT(1)
+#define IXGBE_ACI_PHY_LOW_POWER_MODE BIT(2)
+#define IXGBE_ACI_PHY_EN_LINK BIT(3)
+#define IXGBE_ACI_PHY_AN_MODE BIT(4)
+#define IXGBE_ACI_PHY_EN_MOD_QUAL BIT(5)
+#define IXGBE_ACI_PHY_EN_LESM BIT(6)
+#define IXGBE_ACI_PHY_EN_AUTO_FEC BIT(7)
+#define IXGBE_ACI_PHY_CAPS_MASK GENMASK(7, 0)
+ u8 low_power_ctrl_an;
+#define IXGBE_ACI_PHY_EN_D3COLD_LOW_POWER_AUTONEG BIT(0)
+#define IXGBE_ACI_PHY_AN_EN_CLAUSE28 BIT(1)
+#define IXGBE_ACI_PHY_AN_EN_CLAUSE73 BIT(2)
+#define IXGBE_ACI_PHY_AN_EN_CLAUSE37 BIT(3)
+ u16 eee_cap;
+#define IXGBE_ACI_PHY_EEE_EN_100BASE_TX BIT(0)
+#define IXGBE_ACI_PHY_EEE_EN_1000BASE_T BIT(1)
+#define IXGBE_ACI_PHY_EEE_EN_10GBASE_T BIT(2)
+#define IXGBE_ACI_PHY_EEE_EN_1000BASE_KX BIT(3)
+#define IXGBE_ACI_PHY_EEE_EN_10GBASE_KR BIT(4)
+#define IXGBE_ACI_PHY_EEE_EN_25GBASE_KR BIT(5)
+#define IXGBE_ACI_PHY_EEE_EN_10BASE_T BIT(11)
+ u16 eeer_value;
+ u8 phy_id_oui[4]; /* PHY/Module ID connected on the port */
+ u8 phy_fw_ver[8];
+ u8 link_fec_options;
+#define IXGBE_ACI_PHY_FEC_10G_KR_40G_KR4_EN BIT(0)
+#define IXGBE_ACI_PHY_FEC_10G_KR_40G_KR4_REQ BIT(1)
+#define IXGBE_ACI_PHY_FEC_25G_RS_528_REQ BIT(2)
+#define IXGBE_ACI_PHY_FEC_25G_KR_REQ BIT(3)
+#define IXGBE_ACI_PHY_FEC_25G_RS_544_REQ BIT(4)
+#define IXGBE_ACI_PHY_FEC_25G_RS_CLAUSE91_EN BIT(6)
+#define IXGBE_ACI_PHY_FEC_25G_KR_CLAUSE74_EN BIT(7)
+#define IXGBE_ACI_PHY_FEC_MASK 0xdf
+ u8 module_compliance_enforcement;
+#define IXGBE_ACI_MOD_ENFORCE_STRICT_MODE BIT(0)
+ u8 extended_compliance_code;
+#define IXGBE_ACI_MODULE_TYPE_TOTAL_BYTE 3
+ u8 module_type[IXGBE_ACI_MODULE_TYPE_TOTAL_BYTE];
+#define IXGBE_ACI_MOD_TYPE_BYTE0_SFP_PLUS 0xA0
+#define IXGBE_ACI_MOD_TYPE_BYTE0_QSFP_PLUS 0x80
+#define IXGBE_ACI_MOD_TYPE_IDENT 1
+#define IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_PASSIVE BIT(0)
+#define IXGBE_ACI_MOD_TYPE_BYTE1_SFP_PLUS_CU_ACTIVE BIT(1)
+#define IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_SR BIT(4)
+#define IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_LR BIT(5)
+#define IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_LRM BIT(6)
+#define IXGBE_ACI_MOD_TYPE_BYTE1_10G_BASE_ER BIT(7)
+#define IXGBE_ACI_MOD_TYPE_BYTE2_SFP_PLUS 0xA0
+#define IXGBE_ACI_MOD_TYPE_BYTE2_QSFP_PLUS 0x86
+ u8 qualified_module_count;
+ u8 rsvd2[7]; /* Bytes 47:41 reserved */
+#define IXGBE_ACI_QUAL_MOD_COUNT_MAX 16
+ struct {
+ u8 v_oui[3];
+ u8 rsvd3;
+ u8 v_part[16];
+ u32 v_rev;
+ u64 rsvd4;
+ } qual_modules[IXGBE_ACI_QUAL_MOD_COUNT_MAX];
+};
+
+/* Set PHY capabilities (direct 0x0601)
+ * NOTE: This command must be followed by setup link and restart auto-neg
+ */
+struct ixgbe_aci_cmd_set_phy_cfg {
+ u8 lport_num;
+ u8 reserved[7];
+ u32 addr_high;
+ u32 addr_low;
+};
+
+/* Set PHY config command data structure */
+struct ixgbe_aci_cmd_set_phy_cfg_data {
+ u64 phy_type_low; /* Use values from IXGBE_PHY_TYPE_LOW_* */
+ u64 phy_type_high; /* Use values from IXGBE_PHY_TYPE_HIGH_* */
+ u8 caps;
+#define IXGBE_ACI_PHY_ENA_VALID_MASK 0xef
+#define IXGBE_ACI_PHY_ENA_TX_PAUSE_ABILITY BIT(0)
+#define IXGBE_ACI_PHY_ENA_RX_PAUSE_ABILITY BIT(1)
+#define IXGBE_ACI_PHY_ENA_LOW_POWER BIT(2)
+#define IXGBE_ACI_PHY_ENA_LINK BIT(3)
+#define IXGBE_ACI_PHY_ENA_AUTO_LINK_UPDT BIT(5)
+#define IXGBE_ACI_PHY_ENA_LESM BIT(6)
+#define IXGBE_ACI_PHY_ENA_AUTO_FEC BIT(7)
+ u8 low_power_ctrl_an;
+ u16 eee_cap; /* Value from ixgbe_aci_get_phy_caps */
+ u16 eeer_value; /* Use defines from ixgbe_aci_get_phy_caps */
+ u8 link_fec_opt; /* Use defines from ixgbe_aci_get_phy_caps */
+ u8 module_compliance_enforcement;
+};
+
+/* Restart AN command data structure (direct 0x0605)
+ * Also used for response, with only the lport_num field present.
+ */
+struct ixgbe_aci_cmd_restart_an {
+ u8 lport_num;
+ u8 reserved;
+ u8 cmd_flags;
+#define IXGBE_ACI_RESTART_AN_LINK_RESTART BIT(1)
+#define IXGBE_ACI_RESTART_AN_LINK_ENABLE BIT(2)
+ u8 reserved2[13];
+};
+
+/* Get link status (indirect 0x0607), also used for Link Status Event */
+struct ixgbe_aci_cmd_get_link_status {
+ u8 lport_num;
+ u8 reserved;
+ u16 cmd_flags;
+#define IXGBE_ACI_LSE_M GENMASK(1, 0)
+#define IXGBE_ACI_LSE_NOP 0x0
+#define IXGBE_ACI_LSE_DIS 0x2
+#define IXGBE_ACI_LSE_ENA 0x3
+ /* only response uses this flag */
+#define IXGBE_ACI_LSE_IS_ENABLED 0x1
+ u32 reserved2;
+ u32 addr_high;
+ u32 addr_low;
+};
+
+/* Get link status response data structure, also used for Link Status Event */
+struct ixgbe_aci_cmd_get_link_status_data {
+ u8 topo_media_conflict;
+#define IXGBE_ACI_LINK_TOPO_CONFLICT BIT(0)
+#define IXGBE_ACI_LINK_MEDIA_CONFLICT BIT(1)
+#define IXGBE_ACI_LINK_TOPO_CORRUPT BIT(2)
+#define IXGBE_ACI_LINK_TOPO_UNREACH_PRT BIT(4)
+#define IXGBE_ACI_LINK_TOPO_UNDRUTIL_PRT BIT(5)
+#define IXGBE_ACI_LINK_TOPO_UNDRUTIL_MEDIA BIT(6)
+#define IXGBE_ACI_LINK_TOPO_UNSUPP_MEDIA BIT(7)
+ u8 link_cfg_err;
+#define IXGBE_ACI_LINK_CFG_ERR BIT(0)
+#define IXGBE_ACI_LINK_CFG_COMPLETED BIT(1)
+#define IXGBE_ACI_LINK_ACT_PORT_OPT_INVAL BIT(2)
+#define IXGBE_ACI_LINK_FEAT_ID_OR_CONFIG_ID_INVAL BIT(3)
+#define IXGBE_ACI_LINK_TOPO_CRITICAL_SDP_ERR BIT(4)
+#define IXGBE_ACI_LINK_MODULE_POWER_UNSUPPORTED BIT(5)
+#define IXGBE_ACI_LINK_EXTERNAL_PHY_LOAD_FAILURE BIT(6)
+#define IXGBE_ACI_LINK_INVAL_MAX_POWER_LIMIT BIT(7)
+ u8 link_info;
+#define IXGBE_ACI_LINK_UP BIT(0) /* Link Status */
+#define IXGBE_ACI_LINK_FAULT BIT(1)
+#define IXGBE_ACI_LINK_FAULT_TX BIT(2)
+#define IXGBE_ACI_LINK_FAULT_RX BIT(3)
+#define IXGBE_ACI_LINK_FAULT_REMOTE BIT(4)
+#define IXGBE_ACI_LINK_UP_PORT BIT(5) /* External Port Link Status */
+#define IXGBE_ACI_MEDIA_AVAILABLE BIT(6)
+#define IXGBE_ACI_SIGNAL_DETECT BIT(7)
+ u8 an_info;
+#define IXGBE_ACI_AN_COMPLETED BIT(0)
+#define IXGBE_ACI_LP_AN_ABILITY BIT(1)
+#define IXGBE_ACI_PD_FAULT BIT(2) /* Parallel Detection Fault */
+#define IXGBE_ACI_FEC_EN BIT(3)
+#define IXGBE_ACI_PHY_LOW_POWER BIT(4) /* Low Power State */
+#define IXGBE_ACI_LINK_PAUSE_TX BIT(5)
+#define IXGBE_ACI_LINK_PAUSE_RX BIT(6)
+#define IXGBE_ACI_QUALIFIED_MODULE BIT(7)
+ u8 ext_info;
+#define IXGBE_ACI_LINK_PHY_TEMP_ALARM BIT(0)
+#define IXGBE_ACI_LINK_EXCESSIVE_ERRORS BIT(1) /* Excessive Link Errors */
+ /* Port Tx Suspended */
+#define IXGBE_ACI_LINK_TX_ACTIVE 0
+#define IXGBE_ACI_LINK_TX_DRAINED 1
+#define IXGBE_ACI_LINK_TX_FLUSHED 3
+ u8 lb_status;
+#define IXGBE_ACI_LINK_LB_PHY_LCL BIT(0)
+#define IXGBE_ACI_LINK_LB_PHY_RMT BIT(1)
+#define IXGBE_ACI_LINK_LB_MAC_LCL BIT(2)
+ u16 max_frame_size;
+ u8 cfg;
+#define IXGBE_ACI_LINK_25G_KR_FEC_EN BIT(0)
+#define IXGBE_ACI_LINK_25G_RS_528_FEC_EN BIT(1)
+#define IXGBE_ACI_LINK_25G_RS_544_FEC_EN BIT(2)
+#define IXGBE_ACI_FEC_MASK GENMASK(2, 0)
+ /* Pacing Config */
+#define IXGBE_ACI_CFG_PACING_M GENMASK(6, 3)
+#define IXGBE_ACI_CFG_PACING_TYPE_M BIT(7)
+#define IXGBE_ACI_CFG_PACING_TYPE_AVG 0
+#define IXGBE_ACI_CFG_PACING_TYPE_FIXED IXGBE_ACI_CFG_PACING_TYPE_M
+ /* External Device Power Ability */
+ u8 power_desc;
+#define IXGBE_ACI_PWR_CLASS_M GENMASK(5, 0)
+#define IXGBE_ACI_LINK_PWR_BASET_LOW_HIGH 0
+#define IXGBE_ACI_LINK_PWR_BASET_HIGH 1
+#define IXGBE_ACI_LINK_PWR_QSFP_CLASS_1 0
+#define IXGBE_ACI_LINK_PWR_QSFP_CLASS_2 1
+#define IXGBE_ACI_LINK_PWR_QSFP_CLASS_3 2
+#define IXGBE_ACI_LINK_PWR_QSFP_CLASS_4 3
+ u16 link_speed;
+#define IXGBE_ACI_LINK_SPEED_M GENMASK(10, 0)
+#define IXGBE_ACI_LINK_SPEED_10MB BIT(0)
+#define IXGBE_ACI_LINK_SPEED_100MB BIT(1)
+#define IXGBE_ACI_LINK_SPEED_1000MB BIT(2)
+#define IXGBE_ACI_LINK_SPEED_2500MB BIT(3)
+#define IXGBE_ACI_LINK_SPEED_5GB BIT(4)
+#define IXGBE_ACI_LINK_SPEED_10GB BIT(5)
+#define IXGBE_ACI_LINK_SPEED_20GB BIT(6)
+#define IXGBE_ACI_LINK_SPEED_25GB BIT(7)
+#define IXGBE_ACI_LINK_SPEED_40GB BIT(8)
+#define IXGBE_ACI_LINK_SPEED_50GB BIT(9)
+#define IXGBE_ACI_LINK_SPEED_100GB BIT(10)
+#define IXGBE_ACI_LINK_SPEED_200GB BIT(11)
+#define IXGBE_ACI_LINK_SPEED_UNKNOWN BIT(15)
+ u32 reserved3; /* Aligns next field to 8-byte boundary */
+ u8 ext_fec_status;
+#define IXGBE_ACI_LINK_RS_272_FEC_EN BIT(0) /* RS 272 FEC enabled */
+ u8 reserved4;
+ u64 phy_type_low; /* Use values from ICE_PHY_TYPE_LOW_* */
+ u64 phy_type_high; /* Use values from ICE_PHY_TYPE_HIGH_* */
+ /* Get link status version 2 link partner data */
+ u64 lp_phy_type_low; /* Use values from ICE_PHY_TYPE_LOW_* */
+ u64 lp_phy_type_high; /* Use values from ICE_PHY_TYPE_HIGH_* */
+ u8 lp_fec_adv;
+#define IXGBE_ACI_LINK_LP_10G_KR_FEC_CAP BIT(0)
+#define IXGBE_ACI_LINK_LP_25G_KR_FEC_CAP BIT(1)
+#define IXGBE_ACI_LINK_LP_RS_528_FEC_CAP BIT(2)
+#define IXGBE_ACI_LINK_LP_50G_KR_272_FEC_CAP BIT(3)
+#define IXGBE_ACI_LINK_LP_100G_KR_272_FEC_CAP BIT(4)
+#define IXGBE_ACI_LINK_LP_200G_KR_272_FEC_CAP BIT(5)
+ u8 lp_fec_req;
+#define IXGBE_ACI_LINK_LP_10G_KR_FEC_REQ BIT(0)
+#define IXGBE_ACI_LINK_LP_25G_KR_FEC_REQ BIT(1)
+#define IXGBE_ACI_LINK_LP_RS_528_FEC_REQ BIT(2)
+#define IXGBE_ACI_LINK_LP_KR_272_FEC_REQ BIT(3)
+ u8 lp_flowcontrol;
+#define IXGBE_ACI_LINK_LP_PAUSE_ADV BIT(0)
+#define IXGBE_ACI_LINK_LP_ASM_DIR_ADV BIT(1)
+} __packed;
+
+/* Set event mask command (direct 0x0613) */
+struct ixgbe_aci_cmd_set_event_mask {
+ u8 lport_num;
+ u8 reserved[7];
+ u16 event_mask;
+#define IXGBE_ACI_LINK_EVENT_UPDOWN BIT(1)
+#define IXGBE_ACI_LINK_EVENT_MEDIA_NA BIT(2)
+#define IXGBE_ACI_LINK_EVENT_LINK_FAULT BIT(3)
+#define IXGBE_ACI_LINK_EVENT_PHY_TEMP_ALARM BIT(4)
+#define IXGBE_ACI_LINK_EVENT_EXCESSIVE_ERRORS BIT(5)
+#define IXGBE_ACI_LINK_EVENT_SIGNAL_DETECT BIT(6)
+#define IXGBE_ACI_LINK_EVENT_AN_COMPLETED BIT(7)
+#define IXGBE_ACI_LINK_EVENT_MODULE_QUAL_FAIL BIT(8)
+#define IXGBE_ACI_LINK_EVENT_PORT_TX_SUSPENDED BIT(9)
+#define IXGBE_ACI_LINK_EVENT_TOPO_CONFLICT BIT(10)
+#define IXGBE_ACI_LINK_EVENT_MEDIA_CONFLICT BIT(11)
+#define IXGBE_ACI_LINK_EVENT_PHY_FW_LOAD_FAIL BIT(12)
+ u8 reserved1[6];
+};
+
+struct ixgbe_aci_cmd_link_topo_params {
+ u8 lport_num;
+ u8 lport_num_valid;
+#define IXGBE_ACI_LINK_TOPO_PORT_NUM_VALID BIT(0)
+ u8 node_type_ctx;
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_M GENMASK(3, 0)
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_PHY 0
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_GPIO_CTRL 1
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_MUX_CTRL 2
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_LED_CTRL 3
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_LED 4
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_THERMAL 5
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_CAGE 6
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_MEZZ 7
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_ID_EEPROM 8
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_CLK_CTRL 9
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_CLK_MUX 10
+#define IXGBE_ACI_LINK_TOPO_NODE_TYPE_GPS 11
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_S 4
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_GLOBAL 0
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_BOARD 1
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_PORT 2
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_NODE 3
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_NODE_HANDLE 4
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_DIRECT_BUS_ACCESS 5
+#define IXGBE_ACI_LINK_TOPO_NODE_CTX_NODE_HANDLE_BUS_ADDRESS 6
+ u8 index;
+};
+
+struct ixgbe_aci_cmd_link_topo_addr {
+ struct ixgbe_aci_cmd_link_topo_params topo_params;
+ u16 handle;
+/* Used to decode the handle field */
+#define IXGBE_ACI_LINK_TOPO_HANDLE_BRD_TYPE_M BIT(9)
+#define IXGBE_ACI_LINK_TOPO_HANDLE_BRD_TYPE_LOM BIT(9)
+#define IXGBE_ACI_LINK_TOPO_HANDLE_BRD_TYPE_MEZZ 0
+};
+
+/* Get Link Topology Handle (direct, 0x06E0) */
+struct ixgbe_aci_cmd_get_link_topo {
+ struct ixgbe_aci_cmd_link_topo_addr addr;
+ u8 node_part_num;
+#define IXGBE_ACI_GET_LINK_TOPO_NODE_NR_PCA9575 0x21
+#define IXGBE_ACI_GET_LINK_TOPO_NODE_NR_ZL30632_80032 0x24
+#define IXGBE_ACI_GET_LINK_TOPO_NODE_NR_SI5384 0x25
+#define IXGBE_ACI_GET_LINK_TOPO_NODE_NR_C827 0x31
+#define IXGBE_ACI_GET_LINK_TOPO_NODE_NR_GEN_CLK_MUX 0x47
+#define IXGBE_ACI_GET_LINK_TOPO_NODE_NR_GEN_GPS 0x48
+#define IXGBE_ACI_GET_LINK_TOPO_NODE_NR_E610_PTC 0x49
+ u8 rsvd[9];
+};
+
+/* Get Link Topology Pin (direct, 0x06E1) */
+struct ixgbe_aci_cmd_get_link_topo_pin {
+ struct ixgbe_aci_cmd_link_topo_addr addr;
+ u8 input_io_params;
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_GPIO 0
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_RESET_N 1
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_INT_N 2
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_PRESENT_N 3
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_TX_DIS 4
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_MODSEL_N 5
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_LPMODE 6
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_TX_FAULT 7
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_RX_LOSS 8
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_RS0 9
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_RS1 10
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_EEPROM_WP 11
+/* 12 repeats intentionally due to two different uses depending on context */
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_LED 12
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_RED_LED 12
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_GREEN_LED 13
+#define IXGBE_ACI_LINK_TOPO_IO_FUNC_BLUE_LED 14
+#define IXGBE_ACI_LINK_TOPO_INPUT_IO_TYPE_GPIO 3
+/* Use IXGBE_ACI_LINK_TOPO_NODE_TYPE_* for the type values */
+ u8 output_io_params;
+/* Use IXGBE_ACI_LINK_TOPO_NODE_TYPE_* for the type values */
+ u8 output_io_flags;
+#define IXGBE_ACI_LINK_TOPO_OUTPUT_POLARITY BIT(5)
+#define IXGBE_ACI_LINK_TOPO_OUTPUT_VALUE BIT(6)
+#define IXGBE_ACI_LINK_TOPO_OUTPUT_DRIVEN BIT(7)
+ u8 rsvd[7];
+};
+
+/* Read/Write SFF EEPROM command (indirect 0x06EE) */
+struct ixgbe_aci_cmd_sff_eeprom {
+ u8 lport_num;
+ u8 lport_num_valid;
+#define IXGBE_ACI_SFF_PORT_NUM_VALID BIT(0)
+ u16 i2c_bus_addr;
+#define IXGBE_ACI_SFF_I2CBUS_7BIT_M GENMASK(6, 0)
+#define IXGBE_ACI_SFF_I2CBUS_10BIT_M GENMASK(9, 0)
+#define IXGBE_ACI_SFF_I2CBUS_TYPE_M BIT(10)
+#define IXGBE_ACI_SFF_I2CBUS_TYPE_7BIT 0
+#define IXGBE_ACI_SFF_I2CBUS_TYPE_10BIT IXGBE_ACI_SFF_I2CBUS_TYPE_M
+#define IXGBE_ACI_SFF_NO_PAGE_BANK_UPDATE 0
+#define IXGBE_ACI_SFF_UPDATE_PAGE 1
+#define IXGBE_ACI_SFF_UPDATE_BANK 2
+#define IXGBE_ACI_SFF_UPDATE_PAGE_BANK 3
+#define IXGBE_ACI_SFF_IS_WRITE BIT(15)
+ u16 i2c_offset;
+ u8 module_bank;
+ u8 module_page;
+ u32 addr_high;
+ u32 addr_low;
+};
+
+/* NVM Read command (indirect 0x0701)
+ * NVM Erase commands (direct 0x0702)
+ * NVM Write commands (indirect 0x0703)
+ * NVM Write Activate commands (direct 0x0707)
+ * NVM Shadow RAM Dump commands (direct 0x0707)
+ */
+struct ixgbe_aci_cmd_nvm {
+#define IXGBE_ACI_NVM_MAX_OFFSET 0xFFFFFF
+ u16 offset_low;
+ u8 offset_high; /* For Write Activate offset_high is used as flags2 */
+ u8 cmd_flags;
+#define IXGBE_ACI_NVM_LAST_CMD BIT(0)
+#define IXGBE_ACI_NVM_PCIR_REQ BIT(0) /* Used by NVM Write reply */
+#define IXGBE_ACI_NVM_PRESERVE_ALL BIT(1)
+#define IXGBE_ACI_NVM_ACTIV_SEL_NVM BIT(3) /* Write Activate/SR Dump only */
+#define IXGBE_ACI_NVM_ACTIV_SEL_OROM BIT(4)
+#define IXGBE_ACI_NVM_ACTIV_SEL_NETLIST BIT(5)
+#define IXGBE_ACI_NVM_SPECIAL_UPDATE BIT(6)
+#define IXGBE_ACI_NVM_REVERT_LAST_ACTIV BIT(6) /* Write Activate only */
+#define IXGBE_ACI_NVM_FLASH_ONLY BIT(7)
+#define IXGBE_ACI_NVM_RESET_LVL_M GENMASK(1, 0) /* Write reply only */
+#define IXGBE_ACI_NVM_POR_FLAG 0
+#define IXGBE_ACI_NVM_PERST_FLAG 1
+#define IXGBE_ACI_NVM_EMPR_FLAG 2
+#define IXGBE_ACI_NVM_EMPR_ENA BIT(0) /* Write Activate reply only */
+ /* For Write Activate, several flags are sent as part of a separate
+ * flags2 field using a separate byte. For simplicity of the software
+ * interface, we pass the flags as a 16 bit value so these flags are
+ * all offset by 8 bits
+ */
+#define IXGBE_ACI_NVM_ACTIV_REQ_EMPR BIT(8) /* NVM Write Activate only */
+ u16 module_typeid;
+ u16 length;
+#define IXGBE_ACI_NVM_ERASE_LEN 0xFFFF
+ u32 addr_high;
+ u32 addr_low;
+};
+
+/* NVM Module_Type ID, needed offset and read_len for
+ * struct ixgbe_aci_cmd_nvm.
+ */
+#define IXGBE_ACI_NVM_START_POINT 0
+
+/* NVM Checksum Command (direct, 0x0706) */
+struct ixgbe_aci_cmd_nvm_checksum {
+ u8 flags;
+#define IXGBE_ACI_NVM_CHECKSUM_VERIFY BIT(0)
+#define IXGBE_ACI_NVM_CHECKSUM_RECALC BIT(1)
+ u8 rsvd;
+ u16 checksum; /* Used only by response */
+#define IXGBE_ACI_NVM_CHECKSUM_CORRECT 0xBABA
+ u8 rsvd2[12];
+};
+
+/**
+ * struct ixgbe_aci_desc - Admin Command (AC) descriptor
+ * @flags: IXGBE_ACI_FLAG_* flags
+ * @opcode: Admin command opcode
+ * @datalen: length in bytes of indirect/external data buffer
+ * @retval: return value from firmware
+ * @cookie_high: opaque data high-half
+ * @cookie_low: opaque data low-half
+ * @params: command-specific parameters
+ *
+ * Descriptor format for commands the driver posts via the
+ * Admin Command Interface (ACI).
+ * The firmware writes back onto the command descriptor and returns
+ * the result of the command. Asynchronous events that are not an immediate
+ * result of the command are written to the Admin Command Interface (ACI) using
+ * the same descriptor format. Descriptors are in little-endian notation with
+ * 32-bit words.
+ */
+struct ixgbe_aci_desc {
+ u16 flags;
+ u16 opcode;
+ u16 datalen;
+ u16 retval;
+ u32 cookie_high;
+ u32 cookie_low;
+ union {
+ u8 raw[16];
+ struct ixgbe_aci_cmd_get_ver get_ver;
+ struct ixgbe_aci_cmd_driver_ver driver_ver;
+ struct ixgbe_aci_cmd_get_exp_err exp_err;
+ struct ixgbe_aci_cmd_req_res res_owner;
+ struct ixgbe_aci_cmd_list_caps get_cap;
+ struct ixgbe_aci_cmd_disable_rxen disable_rxen;
+ struct ixgbe_aci_cmd_get_phy_caps get_phy;
+ struct ixgbe_aci_cmd_set_phy_cfg set_phy;
+ struct ixgbe_aci_cmd_restart_an restart_an;
+ struct ixgbe_aci_cmd_get_link_status get_link_status;
+ struct ixgbe_aci_cmd_set_event_mask set_event_mask;
+ struct ixgbe_aci_cmd_get_link_topo get_link_topo;
+ struct ixgbe_aci_cmd_get_link_topo_pin get_link_topo_pin;
+ struct ixgbe_aci_cmd_sff_eeprom read_write_sff_param;
+ struct ixgbe_aci_cmd_nvm nvm;
+ struct ixgbe_aci_cmd_nvm_checksum nvm_checksum;
+ } params;
+};
+
+/* E610-specific adapter context structures */
+
+struct ixgbe_link_status {
+ /* Refer to ixgbe_aci_phy_type for bits definition */
+ u64 phy_type_low;
+ u64 phy_type_high;
+ u16 max_frame_size;
+ u16 link_speed;
+ u16 req_speeds;
+ u8 topo_media_conflict;
+ u8 link_cfg_err;
+ u8 lse_ena; /* Link Status Event notification */
+ u8 link_info;
+ u8 an_info;
+ u8 ext_info;
+ u8 fec_info;
+ u8 pacing;
+ /* Refer to #define from module_type[IXGBE_ACI_MODULE_TYPE_TOTAL_BYTE]
+ * of ixgbe_aci_get_phy_caps structure
+ */
+ u8 module_type[IXGBE_ACI_MODULE_TYPE_TOTAL_BYTE];
+};
+
+/* Common HW capabilities for SW use */
+struct ixgbe_hw_caps {
+ /* Write CSR protection */
+ u64 wr_csr_prot;
+ u32 switching_mode;
+ /* switching mode supported - EVB switching (including cloud) */
+#define IXGBE_NVM_IMAGE_TYPE_EVB 0x0
+
+ /* Manageability mode & supported protocols over MCTP */
+ u32 mgmt_mode;
+#define IXGBE_MGMT_MODE_PASS_THRU_MODE_M GENMASK(3, 0)
+#define IXGBE_MGMT_MODE_CTL_INTERFACE_M GENMASK(7, 4)
+#define IXGBE_MGMT_MODE_REDIR_SB_INTERFACE_M GENMASK(11, 8)
+
+ u32 mgmt_protocols_mctp;
+#define IXGBE_MGMT_MODE_PROTO_RSVD BIT(0)
+#define IXGBE_MGMT_MODE_PROTO_PLDM BIT(1)
+#define IXGBE_MGMT_MODE_PROTO_OEM BIT(2)
+#define IXGBE_MGMT_MODE_PROTO_NC_SI BIT(3)
+
+ u32 os2bmc;
+ u32 valid_functions;
+ /* DCB capabilities */
+ u32 active_tc_bitmap;
+ u32 maxtc;
+
+ /* RSS related capabilities */
+ u32 rss_table_size; /* 512 for PFs and 64 for VFs */
+ u32 rss_table_entry_width; /* RSS Entry width in bits */
+
+ /* Tx/Rx queues */
+ u32 num_rxq; /* Number/Total Rx queues */
+ u32 rxq_first_id; /* First queue ID for Rx queues */
+ u32 num_txq; /* Number/Total Tx queues */
+ u32 txq_first_id; /* First queue ID for Tx queues */
+
+ /* MSI-X vectors */
+ u32 num_msix_vectors;
+ u32 msix_vector_first_id;
+
+ /* Max MTU for function or device */
+ u32 max_mtu;
+
+ /* WOL related */
+ u32 num_wol_proxy_fltr;
+ u32 wol_proxy_vsi_seid;
+
+ /* LED/SDP pin count */
+ u32 led_pin_num;
+ u32 sdp_pin_num;
+
+ /* LED/SDP - Supports up to 12 LED pins and 8 SDP signals */
+#define IXGBE_MAX_SUPPORTED_GPIO_LED 12
+#define IXGBE_MAX_SUPPORTED_GPIO_SDP 8
+ u8 led[IXGBE_MAX_SUPPORTED_GPIO_LED];
+ u8 sdp[IXGBE_MAX_SUPPORTED_GPIO_SDP];
+ /* SR-IOV virtualization */
+ u8 sr_iov_1_1; /* SR-IOV enabled */
+ /* VMDQ */
+ u8 vmdq; /* VMDQ supported */
+
+ /* EVB capabilities */
+ u8 evb_802_1_qbg; /* Edge Virtual Bridging */
+ u8 evb_802_1_qbh; /* Bridge Port Extension */
+
+ u8 dcb;
+ u8 iscsi;
+ u8 ieee_1588;
+ u8 mgmt_cem;
+
+ /* WoL and APM support */
+#define IXGBE_WOL_SUPPORT_M BIT(0)
+#define IXGBE_ACPI_PROG_MTHD_M BIT(1)
+#define IXGBE_PROXY_SUPPORT_M BIT(2)
+ u8 apm_wol_support;
+ u8 acpi_prog_mthd;
+ u8 proxy_support;
+ bool nvm_update_pending_nvm;
+ bool nvm_update_pending_orom;
+ bool nvm_update_pending_netlist;
+#define IXGBE_NVM_PENDING_NVM_IMAGE BIT(0)
+#define IXGBE_NVM_PENDING_OROM BIT(1)
+#define IXGBE_NVM_PENDING_NETLIST BIT(2)
+ bool sec_rev_disabled;
+ bool update_disabled;
+ bool nvm_unified_update;
+ bool netlist_auth;
+#define IXGBE_NVM_MGMT_SEC_REV_DISABLED BIT(0)
+#define IXGBE_NVM_MGMT_UPDATE_DISABLED BIT(1)
+#define IXGBE_NVM_MGMT_UNIFIED_UPD_SUPPORT BIT(3)
+#define IXGBE_NVM_MGMT_NETLIST_AUTH_SUPPORT BIT(5)
+ bool no_drop_policy_support;
+ /* PCIe reset avoidance */
+ bool pcie_reset_avoidance; /* false: not supported, true: supported */
+ /* Post update reset restriction */
+ bool reset_restrict_support; /* false: not supported, true: supported */
+
+ /* External topology device images within the NVM */
+#define IXGBE_EXT_TOPO_DEV_IMG_COUNT 4
+ u32 ext_topo_dev_img_ver_high[IXGBE_EXT_TOPO_DEV_IMG_COUNT];
+ u32 ext_topo_dev_img_ver_low[IXGBE_EXT_TOPO_DEV_IMG_COUNT];
+ u8 ext_topo_dev_img_part_num[IXGBE_EXT_TOPO_DEV_IMG_COUNT];
+#define IXGBE_EXT_TOPO_DEV_IMG_PART_NUM_S 8
+#define IXGBE_EXT_TOPO_DEV_IMG_PART_NUM_M GENMASK(15, 8)
+ bool ext_topo_dev_img_load_en[IXGBE_EXT_TOPO_DEV_IMG_COUNT];
+#define IXGBE_EXT_TOPO_DEV_IMG_LOAD_EN BIT(0)
+ bool ext_topo_dev_img_prog_en[IXGBE_EXT_TOPO_DEV_IMG_COUNT];
+#define IXGBE_EXT_TOPO_DEV_IMG_PROG_EN BIT(1)
+} __packed;
+
+/* Function specific capabilities */
+struct ixgbe_hw_func_caps {
+ u32 num_allocd_vfs; /* Number of allocated VFs */
+ u32 vf_base_id; /* Logical ID of the first VF */
+ u32 guar_num_vsi;
+ struct ixgbe_hw_caps common_cap;
+ bool no_drop_policy_ena;
+};
+
+/* Device wide capabilities */
+struct ixgbe_hw_dev_caps {
+ struct ixgbe_hw_caps common_cap;
+ u32 num_vfs_exposed; /* Total number of VFs exposed */
+ u32 num_vsi_allocd_to_host; /* Excluding EMP VSI */
+ u32 num_flow_director_fltr; /* Number of FD filters available */
+ u32 num_funcs;
+};
+
+/* ACI event information */
+struct ixgbe_aci_event {
+ struct ixgbe_aci_desc desc;
+ u8 *msg_buf;
+ u16 msg_len;
+ u16 buf_len;
+};
+
+struct ixgbe_aci_info {
+ struct mutex lock; /* admin command interface lock */
+ enum ixgbe_aci_err last_status; /* last status of sent admin command */
+};
+
+/* Option ROM version information */
+struct ixgbe_orom_info {
+ u8 major; /* Major version of OROM */
+ u8 patch; /* Patch version of OROM */
+ u16 build; /* Build version of OROM */
+ u32 srev; /* Security revision */
+};
+
+/* NVM version information */
+struct ixgbe_nvm_info {
+ u32 eetrack;
+ u32 srev;
+ u8 major;
+ u8 minor;
+} __packed;
+
+/* netlist version information */
+struct ixgbe_netlist_info {
+ u32 major; /* major high/low */
+ u32 minor; /* minor high/low */
+ u32 type; /* type high/low */
+ u32 rev; /* revision high/low */
+ u32 hash; /* SHA-1 hash word */
+ u16 cust_ver; /* customer version */
+} __packed;
+
+/* Enumeration of possible flash banks for the NVM, OROM, and Netlist modules
+ * of the flash image.
+ */
+enum ixgbe_flash_bank {
+ IXGBE_INVALID_FLASH_BANK,
+ IXGBE_1ST_FLASH_BANK,
+ IXGBE_2ND_FLASH_BANK,
+};
+
+/* information for accessing NVM, OROM, and Netlist flash banks */
+struct ixgbe_bank_info {
+ u32 nvm_ptr; /* Pointer to 1st NVM bank */
+ u32 nvm_size; /* Size of NVM bank */
+ u32 orom_ptr; /* Pointer to 1st OROM bank */
+ u32 orom_size; /* Size of OROM bank */
+ u32 netlist_ptr; /* Ptr to 1st Netlist bank */
+ u32 netlist_size; /* Size of Netlist bank */
+ enum ixgbe_flash_bank nvm_bank; /* Active NVM bank */
+ enum ixgbe_flash_bank orom_bank; /* Active OROM bank */
+ enum ixgbe_flash_bank netlist_bank; /* Active Netlist bank */
+};
+
+/* Flash Chip Information */
+struct ixgbe_flash_info {
+ struct ixgbe_orom_info orom; /* Option ROM version info */
+ u32 flash_size; /* Available flash size in bytes */
+ struct ixgbe_nvm_info nvm; /* NVM version information */
+ struct ixgbe_netlist_info netlist; /* Netlist version info */
+ struct ixgbe_bank_info banks; /* Flash Bank information */
+ u16 sr_words; /* Shadow RAM size in words */
+ u8 blank_nvm_mode; /* is NVM empty (no FW present) */
+};
+
+
+
+#endif /* _IXGBE_TYPE_E610_H_ */