@@ -7,3 +7,4 @@ Power Sourcing Equipment (PSE) Documentation
:maxdepth: 2
introduction
+ pse-pi
new file mode 100644
@@ -0,0 +1,302 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+PSE Power Interface (PSE PI) Documentation
+==========================================
+
+The Power Sourcing Equipment Power Interface (PSE PI) plays a pivotal role in
+the architecture of Power over Ethernet (PoE) systems. It is essentially a
+blueprint that outlines how one or multiple power sources are connected to the
+eight-pin modular jack, commonly known as the Ethernet RJ45 port. This
+connection scheme is crucial for enabling the delivery of power alongside data
+over Ethernet cables.
+
+Documentation and Standards
+---------------------------
+
+The IEEE 802.3 standard provides detailed documentation on the PSE PI.
+Specifically:
+
+- Section "33.2.3 PI pin assignments" covers the pin assignments for PoE
+ systems that utilize two pairs for power delivery.
+- Section "145.2.4 PSE PI" addresses the configuration for PoE systems that
+ deliver power over all four pairs of an Ethernet cable.
+
+PSE PI and Single Pair Ethernet
+-------------------------------
+
+Single Pair Ethernet (SPE) represents a different approach to Ethernet
+connectivity, utilizing just one pair of conductors for both data and power
+transmission. Unlike the configurations detailed in the PSE PI for standard
+Ethernet, which can involve multiple power sourcing arrangements across four or
+two pairs of wires, SPE operates on a simpler model due to its single-pair
+design. As a result, the complexities of choosing between alternative pin
+assignments for power delivery, as described in the PSE PI for multi-pair
+Ethernet, are not applicable to SPE.
+
+Understanding PSE PI
+--------------------
+
+The Power Sourcing Equipment Power Interface (PSE PI) is a framework defining
+how Power Sourcing Equipment (PSE) delivers power to Powered Devices (PDs) over
+Ethernet cables. It details two main configurations for power delivery, known
+as Alternative A and Alternative B, which are distinguished not only by their
+method of power transmission but also by the implications for polarity and data
+transmission direction.
+
+Alternative A and B Overview
+----------------------------
+
+- **Alternative A:** Utilizes RJ45 conductors 1, 2, 3 and 6. In either case of
+ networks 10/100BaseT or 1G/2G/5G/10GBaseT, the pairs used are carrying data.
+ The power delivery's polarity in this alternative can vary based on the MDI
+ (Medium Dependent Interface) or MDI-X (Medium Dependent Interface Crossover)
+ configuration.
+
+- **Alternative B:** Utilizes RJ45 conductors 4, 5, 7 and 8. In case of
+ 10/100BaseT network the pairs used are spare pairs without data and are less
+ influenced by data transmission direction. This is not the case for
+ 1G/2G/5G/10GBaseT network. Alternative B includes two configurations with
+ different polarities, known as variant X and variant S, to accommodate
+ different network requirements and device specifications.
+
+Table 145-3 PSE Pinout Alternatives
+-----------------------------------
+
+The following table outlines the pin configurations for both Alternative A and
+Alternative B.
+
++------------+-------------------+-----------------+-----------------+-----------------+
+| Conductor | Alternative A | Alternative A | Alternative B | Alternative B |
+| | (MDI-X) | (MDI) | (X) | (S) |
++============+===================+=================+=================+=================+
+| 1 | Negative V | Positive V | - | - |
++------------+-------------------+-----------------+-----------------+-----------------+
+| 2 | Negative V | Positive V | - | - |
++------------+-------------------+-----------------+-----------------+-----------------+
+| 3 | Positive V | Negative V | - | - |
++------------+-------------------+-----------------+-----------------+-----------------+
+| 4 | - | - | Negative V | Positive V |
++------------+-------------------+-----------------+-----------------+-----------------+
+| 5 | - | - | Negative V | Positive V |
++------------+-------------------+-----------------+-----------------+-----------------+
+| 6 | Positive V | Negative V | - | - |
++------------+-------------------+-----------------+-----------------+-----------------+
+| 7 | - | - | Positive V | Negative V |
++------------+-------------------+-----------------+-----------------+-----------------+
+| 8 | - | - | Positive V | Negative V |
++------------+-------------------+-----------------+-----------------+-----------------+
+
+.. note::
+ - "Positive V" and "Negative V" indicate the voltage polarity for each pin.
+ - "-" indicates that the pin is not used for power delivery in that
+ specific configuration.
+
+PSE PI compatibilities
+----------------------
+
+The following table outlines the compatibility between the pinout alternative
+and the 1000/2.5G/5G/10GBaseT in the PSE 2 pairs connection.
+
++---------+---------------+---------------------+-----------------------+
+| Variant | Alternative | Power Feeding Type | Compatibility with |
+| | (A/B) | (Direct/Phantom) | 1000/2.5G/5G/10GBaseT |
++=========+===============+=====================+=======================+
+| 1 | A | Phantom | Yes |
++---------+---------------+---------------------+-----------------------+
+| 2 | B | Phantom | Yes |
++---------+---------------+---------------------+-----------------------+
+| 3 | B | Direct | No |
++---------+---------------+---------------------+-----------------------+
+
+.. note::
+ - "Direct" indicate a variant where the power is injected directly to pairs
+ without using magnetics in case of spare pairs.
+ - "Phantom" indicate power path over coils/magnetics as it is done for
+ Alternative A variant.
+
+In case of PSE 4 pairs, a PSE supporting only 10/100BaseT (which mean Direct
+Power on pinout Alternative B) is not compatible with a 4 pairs
+1000/2.5G/5G/10GBaseT.
+
+PSE Power Interface (PSE PI) Connection Diagram
+-----------------------------------------------
+
+The diagram below illustrates the connection architecture between the RJ45
+port, the Ethernet PHY (Physical Layer), and the PSE PI (Power Sourcing
+Equipment Power Interface), demonstrating how power and data are delivered
+simultaneously through an Ethernet cable. The RJ45 port serves as the physical
+interface for these connections, with each of its eight pins connected to both
+the Ethernet PHY for data transmission and the PSE PI for power delivery.
+
+.. code-block::
+
+ +--------------------------+
+ | |
+ | RJ45 Port |
+ | |
+ +--+--+--+--+--+--+--+--+--+ +-------------+
+ 1| 2| 3| 4| 5| 6| 7| 8| | |
+ | | | | | | | o-------------------+ |
+ | | | | | | o--|-------------------+ +<--- PSE 1
+ | | | | | o--|--|-------------------+ |
+ | | | | o--|--|--|-------------------+ |
+ | | | o--|--|--|--|-------------------+ PSE PI |
+ | | o--|--|--|--|--|-------------------+ |
+ | o--|--|--|--|--|--|-------------------+ +<--- PSE 2 (optional)
+ o--|--|--|--|--|--|--|-------------------+ |
+ | | | | | | | | | |
+ +--+--+--+--+--+--+--+--+--+ +-------------+
+ | |
+ | Ethernet PHY |
+ | |
+ +--------------------------+
+
+Simple PSE PI Configuration for Alternative A
+---------------------------------------------
+
+The diagram below illustrates a straightforward PSE PI (Power Sourcing
+Equipment Power Interface) configuration designed to support the Alternative A
+setup for Power over Ethernet (PoE). This implementation is tailored to provide
+power delivery through the data-carrying pairs of an Ethernet cable, suitable
+for either MDI or MDI-X configurations, albeit supporting one variation at a
+time.
+
+.. code-block::
+
+ +-------------+
+ | PSE PI |
+ 8 -----+ +-------------+
+ 7 -----+ Rail 1 |
+ 6 -----+------+----------------------+
+ 5 -----+ | |
+ 4 -----+ | Rail 2 | PSE 1
+ 3 -----+------/ +------------+
+ 2 -----+--+-------------/ |
+ 1 -----+--/ +-------------+
+ |
+ +-------------+
+
+In this configuration:
+
+- Pins 1 and 2, as well as pins 3 and 6, are utilized for power delivery in
+ addition to data transmission. This aligns with the standard wiring for
+ 10/100BaseT Ethernet networks where these pairs are used for data.
+- Rail 1 and Rail 2 represent the positive and negative voltage rails, with
+ Rail 1 connected to pins 1 and 2, and Rail 2 connected to pins 3 and 6.
+ More advanced PSE PI configurations may include integrated or external
+ switches to change the polarity of the voltage rails, allowing for
+ compatibility with both MDI and MDI-X configurations.
+
+More complex PSE PI configurations may include additional components, to support
+Alternative B, or to provide additional features such as power management, or
+additional power delivery capabilities such as 2-pair or 4-pair power delivery.
+
+.. code-block::
+
+ +-------------+
+ | PSE PI |
+ | +---+
+ 8 -----+--------+ | +-------------+
+ 7 -----+--------+ | Rail 1 |
+ 6 -----+--------+ +-----------------+
+ 5 -----+--------+ | |
+ 4 -----+--------+ | Rail 2 | PSE 1
+ 3 -----+--------+ +----------------+
+ 2 -----+--------+ | |
+ 1 -----+--------+ | +-------------+
+ | +---+
+ +-------------+
+
+Device Tree Configuration: Describing PSE PI Configurations
+-----------------------------------------------------------
+
+The necessity for a separate PSE PI node in the device tree is influenced by
+the intricacy of the Power over Ethernet (PoE) system's setup. Here are
+descriptions of both simple and complex PSE PI configurations to illustrate
+this decision-making process:
+
+**Simple PSE PI Configuration:**
+In a straightforward scenario, the PSE PI setup involves a direct, one-to-one
+connection between a single PSE controller and an Ethernet port. This setup
+typically supports basic PoE functionality without the need for dynamic
+configuration or management of multiple power delivery modes. For such simple
+configurations, detailing the PSE PI within the existing PSE controller's node
+may suffice, as the system does not encompass additional complexity that
+warrants a separate node. The primary focus here is on the clear and direct
+association of power delivery to a specific Ethernet port.
+
+**Complex PSE PI Configuration:**
+Contrastingly, a complex PSE PI setup may encompass multiple PSE controllers or
+auxiliary circuits that collectively manage power delivery to one Ethernet
+port. Such configurations might support a range of PoE standards and require
+the capability to dynamically configure power delivery based on the operational
+mode (e.g., PoE2 versus PoE4) or specific requirements of connected devices. In
+these instances, a dedicated PSE PI node becomes essential for accurately
+documenting the system architecture. This node would serve to detail the
+interactions between different PSE controllers, the support for various PoE
+modes, and any additional logic required to coordinate power delivery across
+the network infrastructure.
+
+**Guidance:**
+
+For simple PSE setups, including PSE PI information in the PSE controller node
+might suffice due to the straightforward nature of these systems. However,
+complex configurations, involving multiple components or advanced PoE features,
+benefit from a dedicated PSE PI node. This method adheres to IEEE 802.3
+specifications, improving documentation clarity and ensuring accurate
+representation of the PoE system's complexity.
+
+PSE PI Node: Essential Information
+----------------------------------
+
+The PSE PI (Power Sourcing Equipment Power Interface) node in a device tree can
+include several key pieces of information critical for defining the power
+delivery capabilities and configurations of a PoE (Power over Ethernet) system.
+Below is a list of such information, along with explanations for their
+necessity and reasons why they might not be found within a PSE controller node:
+
+1. **Powered Pairs Configuration**
+
+ - *Description:* Identifies the pairs used for power delivery in the
+ Ethernet cable.
+ - *Necessity:* Essential to ensure the correct pairs are powered according
+ to the board's design.
+ - *PSE Controller Node:* Typically lacks details on physical pair usage,
+ focusing on power regulation.
+
+2. **Polarity of Powered Pairs**
+
+ - *Description:* Specifies the polarity (positive or negative) for each
+ powered pair.
+ - *Necessity:* Critical for safe and effective power transmission to PDs.
+ - *PSE Controller Node:* Polarity management may exceed the standard
+ functionalities of PSE controllers.
+
+3. **PSE Cells Association**
+
+ - *Description:* Details the association of PSE cells with Ethernet ports or
+ pairs in multi-cell configurations.
+ - *Necessity:* Allows for optimized power resource allocation in complex
+ systems.
+ - *PSE Controller Node:* Controllers may not manage cell associations
+ directly, focusing instead on power flow regulation.
+
+4. **Support for PoE Standards**
+
+ - *Description:* Lists the PoE standards and configurations supported by the
+ system.
+ - *Necessity:* Ensures system compatibility with various PDs and adherence
+ to industry standards.
+ - *PSE Controller Node:* Specific capabilities may depend on the overall PSE
+ PI design rather than the controller alone. Multiple PSE cells per PI
+ do not necessarily imply support for multiple PoE standards.
+
+5. **Protection Mechanisms**
+
+ - *Description:* Outlines additional protection mechanisms, such as
+ overcurrent protection and thermal management.
+ - *Necessity:* Provides extra safety and stability, complementing PSE
+ controller protections.
+ - *PSE Controller Node:* Some protections may be implemented via
+ board-specific hardware or algorithms external to the controller.
+
@@ -27,38 +27,182 @@ struct pse_control {
struct kref refcnt;
};
+static int of_load_single_pse_pi_pairset(struct device_node *node,
+ struct pse_pi *pi,
+ int pairset_num)
+{
+ struct device_node *pairset_np;
+ const char *name;
+ int ret;
+
+ ret = of_property_read_string_index(node, "pairset-names",
+ pairset_num, &name);
+ if (ret)
+ return ret;
+
+ if (!strcmp(name, "alternative-a")) {
+ pi->pairset[pairset_num].pinout = ALTERNATIVE_A;
+ } else if (!strcmp(name, "alternative-b")) {
+ pi->pairset[pairset_num].pinout = ALTERNATIVE_B;
+ } else {
+ pr_err("pse: wrong pairset-names value %s (%pOF)\n",
+ name, node);
+ return -EINVAL;
+ }
+
+ pairset_np = of_parse_phandle(node, "pairsets", pairset_num);
+ if (!pairset_np)
+ return -ENODEV;
+
+ pi->pairset[pairset_num].np = pairset_np;
+
+ return 0;
+}
+
/**
- * of_pse_zero_xlate - dummy function for controllers with one only control
- * @pcdev: a pointer to the PSE controller device
- * @pse_spec: PSE line specifier as found in the device tree
+ * of_load_pse_pi_pairsets - load PSE PI pairsets pinout and polarity
+ * @node: a pointer of the device node
+ * @pi: a pointer of the PSE PI to fill
+ * @npairsets: the number of pairsets (1 or 2) used by the PI
*
- * This static translation function is used by default if of_xlate in
- * :c:type:`pse_controller_dev` is not set. It is useful for all PSE
- * controllers with #pse-cells = <0>.
+ * Return: 0 on success and failure value on error
*/
-static int of_pse_zero_xlate(struct pse_controller_dev *pcdev,
- const struct of_phandle_args *pse_spec)
+static int of_load_pse_pi_pairsets(struct device_node *node,
+ struct pse_pi *pi,
+ int npairsets)
{
- return 0;
+ int i, ret;
+
+ ret = of_property_count_strings(node, "pairset-names");
+ if (ret != npairsets) {
+ pr_err("pse: amount of pairsets and pairset-names is not equal %d != %d (%pOF)\n",
+ npairsets, ret, node);
+ return -EINVAL;
+ }
+
+ for (i = 0; i < npairsets; i++) {
+ ret = of_load_single_pse_pi_pairset(node, pi, i);
+ if (ret)
+ goto out;
+ }
+
+ if (npairsets == 2 &&
+ pi->pairset[0].pinout == pi->pairset[1].pinout) {
+ pr_err("pse: two PI pairsets can not have identical pinout (%pOF)",
+ node);
+ ret = -EINVAL;
+ }
+
+out:
+ /* If an error appears, release all the pairset device node kref */
+ if (ret) {
+ of_node_put(pi->pairset[0].np);
+ pi->pairset[0].np = NULL;
+ of_node_put(pi->pairset[1].np);
+ pi->pairset[1].np = NULL;
+ }
+
+ return ret;
+}
+
+static void pse_release_pis(struct pse_controller_dev *pcdev)
+{
+ int i;
+
+ for (i = 0; i <= pcdev->nr_lines; i++) {
+ of_node_put(pcdev->pi[i].pairset[0].np);
+ of_node_put(pcdev->pi[i].pairset[1].np);
+ of_node_put(pcdev->pi[i].np);
+ }
+ kfree(pcdev->pi);
}
/**
- * of_pse_simple_xlate - translate pse_spec to the PSE line number
+ * of_load_pse_pis - load all the PSE PIs
* @pcdev: a pointer to the PSE controller device
- * @pse_spec: PSE line specifier as found in the device tree
*
- * This static translation function is used by default if of_xlate in
- * :c:type:`pse_controller_dev` is not set. It is useful for all PSE
- * controllers with 1:1 mapping, where PSE lines can be indexed by number
- * without gaps.
+ * Return: 0 on success and failure value on error
*/
-static int of_pse_simple_xlate(struct pse_controller_dev *pcdev,
- const struct of_phandle_args *pse_spec)
+static int of_load_pse_pis(struct pse_controller_dev *pcdev)
{
- if (pse_spec->args[0] >= pcdev->nr_lines)
- return -EINVAL;
+ struct device_node *np = pcdev->dev->of_node;
+ struct device_node *node, *pis;
+ int ret;
- return pse_spec->args[0];
+ if (!np)
+ return -ENODEV;
+
+ pis = of_get_child_by_name(np, "pse-pis");
+ if (!pis) {
+ /* no description of PSE PIs */
+ pcdev->no_of_pse_pi = true;
+ return 0;
+ }
+
+ pcdev->pi = kcalloc(pcdev->nr_lines, sizeof(*pcdev->pi), GFP_KERNEL);
+ if (!pcdev->pi) {
+ of_node_put(pis);
+ return -ENOMEM;
+ }
+
+ for_each_child_of_node(pis, node) {
+ struct pse_pi pi = {0};
+ u32 id;
+
+ if (!of_node_name_eq(node, "pse-pi"))
+ continue;
+
+ ret = of_property_read_u32(node, "reg", &id);
+ if (ret) {
+ dev_err(pcdev->dev,
+ "can't get reg property for node '%pOF'",
+ node);
+ goto out;
+ }
+
+ if (id >= pcdev->nr_lines) {
+ dev_err(pcdev->dev,
+ "reg value (%u) is out of range (%u) (%pOF)\n",
+ id, pcdev->nr_lines, node);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ if (pcdev->pi[id].np) {
+ dev_err(pcdev->dev,
+ "other node with same reg value was already registered. %pOF : %pOF\n",
+ pcdev->pi[id].np, node);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ ret = of_count_phandle_with_args(node, "pairsets", NULL);
+ /* npairsets is limited to value one or two */
+ if (ret == 1 || ret == 2) {
+ ret = of_load_pse_pi_pairsets(node, &pi, ret);
+ if (ret)
+ goto out;
+ } else if (ret != ENOENT) {
+ dev_err(pcdev->dev,
+ "error: wrong number of pairsets. Should be 1 or 2, got %d (%pOF)\n",
+ ret, node);
+ ret = -EINVAL;
+ goto out;
+ }
+
+ of_node_get(node);
+ pi.np = node;
+ memcpy(&pcdev->pi[id], &pi, sizeof(pi));
+ }
+
+ of_node_put(pis);
+ return 0;
+
+out:
+ pse_release_pis(pcdev);
+ of_node_put(node);
+ of_node_put(pis);
+ return ret;
}
/**
@@ -67,16 +211,18 @@ static int of_pse_simple_xlate(struct pse_controller_dev *pcdev,
*/
int pse_controller_register(struct pse_controller_dev *pcdev)
{
- if (!pcdev->of_xlate) {
- if (pcdev->of_pse_n_cells == 0)
- pcdev->of_xlate = of_pse_zero_xlate;
- else if (pcdev->of_pse_n_cells == 1)
- pcdev->of_xlate = of_pse_simple_xlate;
- }
+ int ret;
mutex_init(&pcdev->lock);
INIT_LIST_HEAD(&pcdev->pse_control_head);
+ if (!pcdev->nr_lines)
+ pcdev->nr_lines = 1;
+
+ ret = of_load_pse_pis(pcdev);
+ if (ret)
+ return ret;
+
mutex_lock(&pse_list_mutex);
list_add(&pcdev->list, &pse_controller_list);
mutex_unlock(&pse_list_mutex);
@@ -91,6 +237,7 @@ EXPORT_SYMBOL_GPL(pse_controller_register);
*/
void pse_controller_unregister(struct pse_controller_dev *pcdev)
{
+ pse_release_pis(pcdev);
mutex_lock(&pse_list_mutex);
list_del(&pcdev->list);
mutex_unlock(&pse_list_mutex);
@@ -203,8 +350,48 @@ pse_control_get_internal(struct pse_controller_dev *pcdev, unsigned int index)
return psec;
}
-struct pse_control *
-of_pse_control_get(struct device_node *node)
+/**
+ * of_pse_match_pi - Find the PSE PI id matching the device node phandle
+ * @pcdev: a pointer to the PSE controller device
+ * @np: a pointer to the device node
+ *
+ * Return: id of the PSE PI, -EINVAL if not found
+ */
+static int of_pse_match_pi(struct pse_controller_dev *pcdev,
+ struct device_node *np)
+{
+ int i;
+
+ for (i = 0; i <= pcdev->nr_lines; i++) {
+ if (pcdev->pi[i].np == np)
+ return i;
+ }
+
+ return -EINVAL;
+}
+
+/**
+ * psec_id_xlate - translate pse_spec to the PSE line number according
+ * to the number of pse-cells in case of no pse_pi node
+ * @pcdev: a pointer to the PSE controller device
+ * @pse_spec: PSE line specifier as found in the device tree
+ *
+ * Return: 0 if #pse-cells = <0>. Return PSE line number otherwise.
+ */
+static int psec_id_xlate(struct pse_controller_dev *pcdev,
+ const struct of_phandle_args *pse_spec)
+{
+ if (!pcdev->of_pse_n_cells)
+ return 0;
+
+ if (pcdev->of_pse_n_cells > 1 ||
+ pse_spec->args[0] >= pcdev->nr_lines)
+ return -EINVAL;
+
+ return pse_spec->args[0];
+}
+
+struct pse_control *of_pse_control_get(struct device_node *node)
{
struct pse_controller_dev *r, *pcdev;
struct of_phandle_args args;
@@ -222,7 +409,14 @@ of_pse_control_get(struct device_node *node)
mutex_lock(&pse_list_mutex);
pcdev = NULL;
list_for_each_entry(r, &pse_controller_list, list) {
- if (args.np == r->dev->of_node) {
+ if (!r->no_of_pse_pi) {
+ ret = of_pse_match_pi(r, args.np);
+ if (ret >= 0) {
+ pcdev = r;
+ psec_id = ret;
+ break;
+ }
+ } else if (args.np == r->dev->of_node) {
pcdev = r;
break;
}
@@ -238,10 +432,12 @@ of_pse_control_get(struct device_node *node)
goto out;
}
- psec_id = pcdev->of_xlate(pcdev, &args);
- if (psec_id < 0) {
- psec = ERR_PTR(psec_id);
- goto out;
+ if (pcdev->no_of_pse_pi) {
+ psec_id = psec_id_xlate(pcdev, &args);
+ if (psec_id < 0) {
+ psec = ERR_PTR(psec_id);
+ goto out;
+ }
}
/* pse_list_mutex also protects the pcdev's pse_control list */
@@ -64,6 +64,36 @@ struct device_node;
struct of_phandle_args;
struct pse_control;
+/* PSE PI pairset pinout can either be Alternative A or Alternative B */
+enum pse_pi_pairset_pinout {
+ ALTERNATIVE_A,
+ ALTERNATIVE_B,
+};
+
+/**
+ * struct pse_pi_pairset - PSE PI pairset entity describing the pinout
+ * alternative ant its phandle
+ *
+ * @pinout: description of the pinout alternative
+ * @np: device node pointer describing the pairset phandle
+ */
+struct pse_pi_pairset {
+ enum pse_pi_pairset_pinout pinout;
+ struct device_node *np;
+};
+
+/**
+ * struct pse_pi - PSE PI (Power Interface) entity as described in
+ * IEEE 802.3-2022 145.2.4
+ *
+ * @pairset: table of the PSE PI pinout alternative for the two pairset
+ * @np: device node pointer of the PSE PI node
+ */
+struct pse_pi {
+ struct pse_pi_pairset pairset[2];
+ struct device_node *np;
+};
+
/**
* struct pse_controller_dev - PSE controller entity that might
* provide multiple PSE controls
@@ -73,11 +103,11 @@ struct pse_control;
* @pse_control_head: head of internal list of requested PSE controls
* @dev: corresponding driver model device struct
* @of_pse_n_cells: number of cells in PSE line specifiers
- * @of_xlate: translation function to translate from specifier as found in the
- * device tree to id as given to the PSE control ops
* @nr_lines: number of PSE controls in this controller device
* @lock: Mutex for serialization access to the PSE controller
* @types: types of the PSE controller
+ * @pi: table of PSE PIs described in this controller device
+ * @no_of_pse_pi: flag set if the pse_pis devicetree node is not used
*/
struct pse_controller_dev {
const struct pse_controller_ops *ops;
@@ -86,11 +116,11 @@ struct pse_controller_dev {
struct list_head pse_control_head;
struct device *dev;
int of_pse_n_cells;
- int (*of_xlate)(struct pse_controller_dev *pcdev,
- const struct of_phandle_args *pse_spec);
unsigned int nr_lines;
struct mutex lock;
enum ethtool_pse_types types;
+ struct pse_pi *pi;
+ bool no_of_pse_pi;
};
#if IS_ENABLED(CONFIG_PSE_CONTROLLER)