From patchwork Fri May 3 13:13:51 2024 Content-Type: text/plain; charset="utf-8" MIME-Version: 1.0 Content-Transfer-Encoding: 7bit X-Patchwork-Submitter: Oleksij Rempel X-Patchwork-Id: 13652849 X-Patchwork-Delegate: kuba@kernel.org Received: from metis.whiteo.stw.pengutronix.de (metis.whiteo.stw.pengutronix.de [185.203.201.7]) (using TLSv1.2 with cipher ECDHE-RSA-AES256-GCM-SHA384 (256/256 bits)) (No client certificate requested) by smtp.subspace.kernel.org (Postfix) with ESMTPS id BFF5C15382D for ; Fri, 3 May 2024 13:14:08 +0000 (UTC) Authentication-Results: smtp.subspace.kernel.org; arc=none smtp.client-ip=185.203.201.7 ARC-Seal: i=1; a=rsa-sha256; d=subspace.kernel.org; s=arc-20240116; t=1714742055; cv=none; b=rFoFh1238lTUSEoY6FpbzhhACYMj/pKFGPKSuwxrL+o9DhOllNBb9clJEYxf8hhDomLH8jfdTNh7y5qcZPAal7piRp7Pms3Fa/QIz10X5jxm8cLsOKB6e96kgfvbiz4wzsFP/z2tqtxz+Qfc1ZixMuQTAzs+kj7H7RkcaQYxYOc= ARC-Message-Signature: i=1; a=rsa-sha256; d=subspace.kernel.org; s=arc-20240116; t=1714742055; c=relaxed/simple; bh=10ylxSO/mJzIRfnId7mBvEvqvoVFQCyMabO+Q7R4XgE=; h=From:To:Cc:Subject:Date:Message-Id:In-Reply-To:References: MIME-Version; b=T4idjsghNizr75MI6/TqkxPXH4fGEdf9SDRrFFeHacSkrBiYh8RFWdmLvyWj05svy73KzkagAQsCSq6gdaqDAZhFyoYd2He1VOVgKfIq6IIV1e0cOEJ4wg2On8d0R3IlD+i4AYDkRM0stjKdLgFUDPEBL8mVSp5eQwZXBknJTIs= ARC-Authentication-Results: i=1; smtp.subspace.kernel.org; dmarc=none (p=none dis=none) header.from=pengutronix.de; spf=pass smtp.mailfrom=pengutronix.de; arc=none smtp.client-ip=185.203.201.7 Authentication-Results: smtp.subspace.kernel.org; dmarc=none (p=none dis=none) header.from=pengutronix.de Authentication-Results: smtp.subspace.kernel.org; spf=pass smtp.mailfrom=pengutronix.de Received: from drehscheibe.grey.stw.pengutronix.de ([2a0a:edc0:0:c01:1d::a2]) by metis.whiteo.stw.pengutronix.de with esmtps (TLS1.3:ECDHE_RSA_AES_256_GCM_SHA384:256) (Exim 4.92) (envelope-from ) id 1s2sjb-0006EM-6l; Fri, 03 May 2024 15:13:55 +0200 Received: from [2a0a:edc0:0:1101:1d::ac] (helo=dude04.red.stw.pengutronix.de) by drehscheibe.grey.stw.pengutronix.de with esmtps (TLS1.3) tls TLS_ECDHE_RSA_WITH_AES_256_GCM_SHA384 (Exim 4.94.2) (envelope-from ) id 1s2sjZ-00FiKQ-Ts; Fri, 03 May 2024 15:13:53 +0200 Received: from ore by dude04.red.stw.pengutronix.de with local (Exim 4.96) (envelope-from ) id 1s2sjZ-008GIK-2Z; Fri, 03 May 2024 15:13:53 +0200 From: Oleksij Rempel To: "David S. Miller" , Andrew Lunn , Eric Dumazet , Florian Fainelli , Jakub Kicinski , Paolo Abeni , Vladimir Oltean , Woojung Huh , Arun Ramadoss Cc: Oleksij Rempel , kernel@pengutronix.de, linux-kernel@vger.kernel.org, netdev@vger.kernel.org, UNGLinuxDriver@microchip.com, David Ahern , Simon Horman , Willem de Bruijn , =?utf-8?q?S=C3=B8ren_Andersen?= Subject: [PATCH net-next v7 12/12] selftests: microchip: add test for QoS support on KSZ9477 switch family Date: Fri, 3 May 2024 15:13:51 +0200 Message-Id: <20240503131351.1969097-13-o.rempel@pengutronix.de> X-Mailer: git-send-email 2.39.2 In-Reply-To: <20240503131351.1969097-1-o.rempel@pengutronix.de> References: <20240503131351.1969097-1-o.rempel@pengutronix.de> Precedence: bulk X-Mailing-List: netdev@vger.kernel.org List-Id: List-Subscribe: List-Unsubscribe: MIME-Version: 1.0 X-SA-Exim-Connect-IP: 2a0a:edc0:0:c01:1d::a2 X-SA-Exim-Mail-From: ore@pengutronix.de X-SA-Exim-Scanned: No (on metis.whiteo.stw.pengutronix.de); SAEximRunCond expanded to false X-PTX-Original-Recipient: netdev@vger.kernel.org X-Patchwork-Delegate: kuba@kernel.org Add tests covering following functionality on KSZ9477 switch family: - default port priority - global DSCP to Internal Priority Mapping - apptrust configuration This script was tested on KSZ9893R Signed-off-by: Oleksij Rempel --- .../drivers/net/microchip/ksz9477_qos.sh | 668 ++++++++++++++++++ 1 file changed, 668 insertions(+) create mode 100755 tools/testing/selftests/drivers/net/microchip/ksz9477_qos.sh diff --git a/tools/testing/selftests/drivers/net/microchip/ksz9477_qos.sh b/tools/testing/selftests/drivers/net/microchip/ksz9477_qos.sh new file mode 100755 index 0000000000000..82be5d0133301 --- /dev/null +++ b/tools/testing/selftests/drivers/net/microchip/ksz9477_qos.sh @@ -0,0 +1,668 @@ +#!/bin/bash +# SPDX-License-Identifier: GPL-2.0 +# Copyright (c) 2024 Pengutronix, Oleksij Rempel + +# The script is adopted to work with the Microchip KSZ switch driver. + +ETH_FCS_LEN=4 + +WAIT_TIME=1 +NUM_NETIFS=4 +REQUIRE_JQ="yes" +REQUIRE_MZ="yes" +STABLE_MAC_ADDRS=yes +NETIF_CREATE=no +lib_dir=$(dirname $0)/../../../net/forwarding +source $lib_dir/tc_common.sh +source $lib_dir/lib.sh + +require_command dcb + +h1=${NETIFS[p1]} +swp1=${NETIFS[p2]} +swp2=${NETIFS[p3]} +h2=${NETIFS[p4]} + +H1_IPV4="192.0.2.1" +H2_IPV4="192.0.2.2" +H1_IPV6="2001:db8:1::1" +H2_IPV6="2001:db8:1::2" + +# On h1_ and h2_create do not set IP addresses to avoid interaction with the +# system, to keep packet counters clean. +h1_create() +{ + simple_if_init $h1 + sysctl_set net.ipv6.conf.${h1}.disable_ipv6 1 + # Get the MAC address of the interface to use it with mausezahn + h1_mac=$(ip -j link show dev ${h1} | jq -e '.[].address') +} + +h1_destroy() +{ + sysctl_restore net.ipv6.conf.${h1}.disable_ipv6 + simple_if_fini $h1 +} + +h2_create() +{ + simple_if_init $h2 + sysctl_set net.ipv6.conf.${h2}.disable_ipv6 1 + h2_mac=$(ip -j link show dev ${h2} | jq -e '.[].address') +} + +h2_destroy() +{ + sysctl_restore net.ipv6.conf.${h2}.disable_ipv6 + simple_if_fini $h2 +} + +switch_create() +{ + ip link set ${swp1} up + ip link set ${swp2} up + sysctl_set net.ipv6.conf.${swp1}.disable_ipv6 1 + sysctl_set net.ipv6.conf.${swp2}.disable_ipv6 1 + + # Ports should trust VLAN PCP even with vlan_filtering=0 + ip link add br0 type bridge + ip link set ${swp1} master br0 + ip link set ${swp2} master br0 + ip link set br0 up + sysctl_set net.ipv6.conf.br0.disable_ipv6 1 +} + +switch_destroy() +{ + sysctl_restore net.ipv6.conf.${swp2}.disable_ipv6 + sysctl_restore net.ipv6.conf.${swp1}.disable_ipv6 + + ip link del br0 +} + +setup_prepare() +{ + vrf_prepare + + h1_create + h2_create + switch_create +} + +cleanup() +{ + pre_cleanup + + h2_destroy + h1_destroy + switch_destroy + + vrf_cleanup +} + +set_apptrust_order() +{ + local if_name=$1 + local order=$2 + + dcb apptrust set dev ${if_name} order ${order} +} + +# Function to extract a specified field from a given JSON stats string +extract_network_stat() { + local stats_json=$1 + local field_name=$2 + + echo $(echo "$stats_json" | jq -r "$field_name") +} + +run_test() +{ + local test_name=$1; + local apptrust_order=$2; + local port_prio=$3; + local dscp_ipv=$4; + local dscp=$5; + local have_vlan=$6; + local pcp_ipv=$7; + local vlan_pcp=$8; + local ip_v6=$9 + + local rx_ipv + local tx_ipv + + RET=0 + + # Send some packet to populate the switch MAC table + $MZ ${h2} -a ${h2_mac} -b ${h1_mac} -p 64 -t icmp echores -c 1 + + # Based on the apptrust order, set the expected Internal Priority values + # for the RX and TX paths. + if [ "${apptrust_order}" == "" ]; then + echo "Apptrust order not set." + rx_ipv=${port_prio} + tx_ipv=${port_prio} + elif [ "${apptrust_order}" == "dscp" ]; then + echo "Apptrust order is DSCP." + rx_ipv=${dscp_ipv} + tx_ipv=${dscp_ipv} + elif [ "${apptrust_order}" == "pcp" ]; then + echo "Apptrust order is PCP." + rx_ipv=${pcp_ipv} + tx_ipv=${pcp_ipv} + elif [ "${apptrust_order}" == "pcp dscp" ]; then + echo "Apptrust order is PCP DSCP." + if [ ${have_vlan} -eq 1 ]; then + rx_ipv=$((dscp_ipv > pcp_ipv ? dscp_ipv : pcp_ipv)) + tx_ipv=${pcp_ipv} + else + rx_ipv=${dscp_ipv} + tx_ipv=${dscp_ipv} + fi + else + RET=1 + echo "Error: Unknown apptrust order ${apptrust_order}" + log_test "${test_name}" + return + fi + + # Most/all? of the KSZ switches do not provide per-TC counters. There + # are only tx_hi and rx_hi counters, which are used to count packets + # which are considered as high priority and most likely not assigned + # to the queue 0. + # On the ingress path, packets seem to get high priority status + # independently of the DSCP or PCP global mapping. On the egress path, + # the high priority status is assigned based on the DSCP or PCP global + # map configuration. + # The thresholds for the high priority status are not documented, but + # it seems that the switch considers packets as high priority on the + # ingress path if detected Internal Priority is greater than 0. On the + # egress path, the switch considers packets as high priority if + # detected Internal Priority is greater than 1. + if [ ${rx_ipv} -ge 1 ]; then + local expect_rx_high_prio=1 + else + local expect_rx_high_prio=0 + fi + + if [ ${tx_ipv} -ge 2 ]; then + local expect_tx_high_prio=1 + else + local expect_tx_high_prio=0 + fi + + # Use ip tool to get the current switch packet counters. ethool stats + # need to be recalculated to get the correct values. + local swp1_stats=$(ip -s -j link show dev ${swp1}) + local swp2_stats=$(ip -s -j link show dev ${swp2}) + local swp1_rx_packets_before=$(extract_network_stat "$swp1_stats" \ + '.[0].stats64.rx.packets') + local swp1_rx_bytes_before=$(extract_network_stat "$swp1_stats" \ + '.[0].stats64.rx.bytes') + local swp2_tx_packets_before=$(extract_network_stat "$swp2_stats" \ + '.[0].stats64.tx.packets') + local swp2_tx_bytes_before=$(extract_network_stat "$swp2_stats" \ + '.[0].stats64.tx.bytes') + local swp1_rx_hi_before=$(ethtool_stats_get ${swp1} "rx_hi") + local swp2_tx_hi_before=$(ethtool_stats_get ${swp2} "tx_hi") + + # Assamble the mausezahn command based on the test parameters + # For the testis with ipv4 or ipv6, use icmp response packets, + # to avoid interaction with the system, to keep packet counters + # clean. + if [ ${ip_v6} -eq 0 ]; then + local ip="-a ${h1_mac} -b ${h2_mac} -A ${H1_IPV4} \ + -B ${H2_IPV4} -t icmp unreach,code=1,dscp=${dscp}" + else + local ip="-6 -a ${h1_mac} -b ${h2_mac} -A ${H1_IPV6} \ + -B ${H2_IPV6} -t icmp6 type=1,code=0,dscp=${dscp}" + fi + + if [ ${have_vlan} -eq 1 ]; then + local vlan_pcp_opt="-Q ${vlan_pcp}:0" + else + local vlan_pcp_opt="" + fi + $MZ ${h1} ${ip} -c ${PING_COUNT} -d 10msec ${vlan_pcp_opt} + + # Wait until the switch packet counters are updated + sleep 6 + + local swp1_stats=$(ip -s -j link show dev ${swp1}) + local swp2_stats=$(ip -s -j link show dev ${swp2}) + + local swp1_rx_packets_after=$(extract_network_stat "$swp1_stats" \ + '.[0].stats64.rx.packets') + local swp1_rx_bytes_after=$(extract_network_stat "$swp1_stats" \ + '.[0].stats64.rx.bytes') + local swp2_tx_packets_after=$(extract_network_stat "$swp2_stats" \ + '.[0].stats64.tx.packets') + local swp2_tx_bytes_after=$(extract_network_stat "$swp2_stats" \ + '.[0].stats64.tx.bytes') + + local swp1_rx_packets_diff=$((${swp1_rx_packets_after} - \ + ${swp1_rx_packets_before})) + local swp2_tx_packets_diff=$((${swp2_tx_packets_after} - \ + ${swp2_tx_packets_before})) + + local swp1_rx_hi_after=$(ethtool_stats_get ${swp1} "rx_hi") + local swp2_tx_hi_after=$(ethtool_stats_get ${swp2} "tx_hi") + + # Test if any packets were received on swp1, we will rx before and after + if [ ${swp1_rx_packets_diff} -lt ${PING_COUNT} ]; then + echo "Not expected amount of received packets on ${swp1}" + echo "before ${swp1_rx_packets_before} after ${swp1_rx_packets_after}" + RET=1 + fi + + # Test if any packets were transmitted on swp2, we will tx before and after + if [ ${swp2_tx_packets_diff} -lt ${PING_COUNT} ]; then + echo "Not expected amount of transmitted packets on ${swp2}" + echo "before ${swp2_tx_packets_before} after ${swp2_tx_packets_after}" + RET=1 + fi + + # tx/rx_hi counted in bytes. So, we need to compare the difference in bytes + local swp1_rx_bytes_diff=$(($swp1_rx_bytes_after - $swp1_rx_bytes_before)) + local swp2_tx_bytes_diff=$(($swp2_tx_bytes_after - $swp2_tx_bytes_before)) + local swp1_rx_hi_diff=$(($swp1_rx_hi_after - $swp1_rx_hi_before)) + local swp2_tx_hi_diff=$(($swp2_tx_hi_after - $swp2_tx_hi_before)) + + if [ ${expect_rx_high_prio} -eq 1 ]; then + swp1_rx_hi_diff=$((${swp1_rx_hi_diff} - \ + ${swp1_rx_packets_diff} * ${ETH_FCS_LEN})) + if [ ${swp1_rx_hi_diff} -ne ${swp1_rx_bytes_diff} ]; then + echo "Not expected amount of high priority packets received on ${swp1}" + echo "RX hi diff: ${swp1_rx_hi_diff}, expected RX bytes diff: ${swp1_rx_bytes_diff}" + RET=1 + fi + else + if [ ${swp1_rx_hi_diff} -ne 0 ]; then + echo "Unexpected amount of high priority packets received on ${swp1}" + echo "RX hi diff: ${swp1_rx_hi_diff}, expected 0" + RET=1 + fi + fi + + if [ ${expect_tx_high_prio} -eq 1 ]; then + swp2_tx_hi_diff=$((${swp2_tx_hi_diff} - \ + ${swp2_tx_packets_diff} * ${ETH_FCS_LEN})) + if [ ${swp2_tx_hi_diff} -ne ${swp2_tx_bytes_diff} ]; then + echo "Not expected amount of high priority packets transmitted on ${swp2}" + echo "TX hi diff: ${swp2_tx_hi_diff}, expected TX bytes diff: ${swp2_tx_bytes_diff}" + RET=1 + fi + else + if [ ${swp2_tx_hi_diff} -ne 0 ]; then + echo "Unexpected amount of high priority packets transmitted on ${swp2}" + echo "TX hi diff: ${swp2_tx_hi_diff}, expected 0" + RET=1 + fi + fi + + log_test "${test_name}" +} + +run_test_dscp() +{ + # IPv4 test + run_test "$1" "$2" "$3" "$4" "$5" 0 0 0 0 + # IPv6 test + run_test "$1" "$2" "$3" "$4" "$5" 0 0 0 1 +} + +run_test_dscp_pcp() +{ + # IPv4 test + run_test "$1" "$2" "$3" "$4" "$5" 1 "$6" "$7" 0 + # IPv6 test + run_test "$1" "$2" "$3" "$4" "$5" 1 "$6" "$7" 1 +} + +port_default_prio_get() +{ + local if_name=$1 + local prio + + prio="$(dcb -j app show dev ${if_name} default-prio | \ + jq '.default_prio[]')" + if [ -z "${prio}" ]; then + prio=0 + fi + + echo ${prio} +} + +test_port_default() +{ + local orig_apptrust=$(port_get_default_apptrust ${swp1}) + local orig_prio=$(port_default_prio_get ${swp1}) + local apptrust_order="" + + RET=0 + + # Make sure no other priority sources will interfere with the test + set_apptrust_order ${swp1} "${apptrust_order}" + + for val in $(seq 0 7); do + dcb app replace dev ${swp1} default-prio ${val} + if [ $val -ne $(port_default_prio_get ${swp1}) ]; then + RET=1 + break + fi + + run_test_dscp "Port-default QoS classification, prio: ${val}" \ + "${apptrust_order}" ${val} 0 0 + done + + set_apptrust_order ${swp1} "${orig_apptrust}" + if [[ "$orig_apptrust" != "$(port_get_default_apptrust ${swp1})" ]]; then + RET=1 + fi + + dcb app replace dev ${swp1} default-prio ${orig_prio} + if [ $orig_prio -ne $(port_default_prio_get ${swp1}) ]; then + RET=1 + fi + + log_test "Port-default QoS classification" +} + +port_get_default_apptrust() +{ + local if_name=$1 + + dcb -j apptrust show dev ${if_name} | jq -r '.order[]' | \ + tr '\n' ' ' | xargs +} + +test_port_apptrust() +{ + local original_dscp_prios_swp1=$(get_dscp_prios ${swp1}) + local orig_apptrust=$(port_get_default_apptrust ${swp1}) + local orig_port_prio=$(port_default_prio_get ${swp1}) + local order_variants=("pcp dscp" "dscp" "pcp") + local apptrust_order + local port_prio + local dscp_prio + local pcp_prio + local dscp + local pcp + + RET=0 + + # First, test if apptrust configuration as taken by the kernel + for order in "${order_variants[@]}"; do + set_apptrust_order ${swp1} "${order}" + if [[ "$order" != "$(port_get_default_apptrust ${swp1})" ]]; then + RET=1 + break + fi + done + + log_test "Apptrust, supported variants" + + # To test if the apptrust configuration is working as expected, we need + # to set DSCP priorities for the switch port. + init_dscp_prios "${swp1}" "${original_dscp_prios_swp1}" + + # Start with a simple test where all apptrust sources are disabled + # default port priority is 0, DSCP priority is mapped to 7. + # No high priority packets should be received or transmitted. + port_prio=0 + dscp_prio=7 + dscp=4 + + dcb app replace dev ${swp1} default-prio ${port_prio} + dcb app replace dev ${swp1} dscp-prio ${dscp}:${dscp_prio} + + apptrust_order="" + set_apptrust_order ${swp1} "${apptrust_order}" + # Test with apptrust sources disabled, Packets should get port default + # priority which is 0 + run_test_dscp "Apptrust, all disabled. DSCP-prio ${dscp}:${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} + + apptrust_order="pcp" + set_apptrust_order ${swp1} "${apptrust_order}" + # If PCP is enabled, packets should get PCP priority, which is not + # set in this test (no VLAN tags are present in the packet). No high + # priority packets should be received or transmitted. + run_test_dscp "Apptrust, PCP enabled. DSCP-prio ${dscp}:${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} + + apptrust_order="dscp" + set_apptrust_order ${swp1} "${apptrust_order}" + # If DSCP is enabled, packets should get DSCP priority which is set to 7 + # in this test. High priority packets should be received and transmitted. + run_test_dscp "Apptrust, DSCP enabled. DSCP-prio ${dscp}:${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} + + apptrust_order="pcp dscp" + set_apptrust_order ${swp1} "${apptrust_order}" + # If PCP and DSCP are enabled, PCP would have higher apptrust priority + # so packets should get PCP priority. But in this test VLAN PCP is not + # set, so it should get DSCP priority which is set to 7. High priority + # packets should be received and transmitted. + run_test_dscp "Apptrust, PCP and DSCP are enabled. DSCP-prio ${dscp}:${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} + + # If VLAN PCP is set, it should have higher apptrust priority than DSCP + # so packets should get VLAN PCP priority. Send packets with VLAN PCP + # set to 0, DSCP set to 7. Packets should get VLAN PCP priority. + # No high priority packets should be transmitted. Due to nature of the + # switch, high priority packets will be received. + pcp_prio=0 + pcp=0 + run_test_dscp_pcp "Apptrust, PCP and DSCP are enabled. PCP ${pcp_prio}, DSCP-prio ${dscp}:${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} ${pcp_prio} ${pcp} + + # If VLAN PCP is set to 7, it should have higher apptrust priority than + # DSCP so packets should get VLAN PCP priority. Send packets with VLAN + # PCP set to 7, DSCP set to 7. Packets should get VLAN PCP priority. + # High priority packets should be received and transmitted. + pcp_prio=7 + pcp=7 + run_test_dscp_pcp "Apptrust, PCP and DSCP are enabled. PCP ${pcp_prio}, DSCP-prio ${dscp}:${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} ${pcp_prio} ${pcp} + # Now make sure that the switch is able to handle the case where DSCP + # priority is set to 0 and PCP priority is set to 7. Packets should get + # PCP priority. High priority packets should be received and transmitted. + dscp_prio=0 + dcb app replace dev ${swp1} dscp-prio ${dscp}:${dscp_prio} + run_test_dscp_pcp "Apptrust, PCP and DSCP are enabled. PCP ${pcp_prio}, DSCP-prio ${dscp}:${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} ${pcp_prio} ${pcp} + # If both VLAN PCP and DSCP are set to 0, packets should get 0 priority. + # No high priority packets should be received or transmitted. + pcp_prio=0 + pcp=0 + run_test_dscp_pcp "Apptrust, PCP and DSCP are enabled. PCP ${pcp_prio}, DSCP-prio ${dscp}:${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} ${pcp_prio} ${pcp} + + # Restore original priorities + if ! restore_priorities "${swp1}" "${original_dscp_prios_swp1}"; then + RET=1 + fi + + set_apptrust_order ${swp1} "${orig_apptrust}" + if [ "$orig_apptrust" != "$(port_get_default_apptrust ${swp1})" ]; then + RET=1 + fi + + dcb app replace dev ${swp1} default-prio ${orig_port_prio} + if [ $orig_port_prio -ne $(port_default_prio_get ${swp1}) ]; then + RET=1 + fi + + log_test "Apptrust, restore original settings" +} + +# Function to get current DSCP priorities +get_dscp_prios() { + local if_name=$1 + dcb -j app show dev ${if_name} | jq -c '.dscp_prio' +} + +# Function to set a specific DSCP priority on a device +replace_dscp_prio() { + local if_name=$1 + local dscp=$2 + local prio=$3 + dcb app replace dev ${if_name} dscp-prio ${dscp}:${prio} +} + +# Function to compare DSCP maps +compare_dscp_maps() { + local old_json=$1 + local new_json=$2 + local dscp=$3 + local prio=$4 + + # Create a modified old_json with the expected change for comparison + local modified_old_json=$(echo "$old_json" | + jq --argjson dscp $dscp --argjson prio $prio \ + 'map(if .[0] == $dscp then [$dscp, $prio] else . end)' | + tr -d " \n") + + # Compare new_json with the modified_old_json + if [[ "$modified_old_json" == "$new_json" ]]; then + return 0 + else + return 1 + fi +} + +# Function to set DSCP priorities +set_and_verify_dscp() { + local port=$1 + local dscp=$2 + local new_prio=$3 + + local old_prios=$(get_dscp_prios $port) + + replace_dscp_prio "$port" $dscp $new_prio + + # Fetch current settings and compare + local current_prios=$(get_dscp_prios $port) + if ! compare_dscp_maps "$old_prios" "$current_prios" $dscp $new_prio; then + echo "Error: Unintended changes detected in DSCP map for $port after setting DSCP $dscp to $new_prio." + return 1 + fi + return 0 +} + +# Function to restore original priorities +restore_priorities() { + local port=$1 + local original_prios=$2 + + echo "Removing test artifacts for $port" + local current_prios=$(get_dscp_prios $port) + local prio_str=$(echo "$current_prios" | + jq -r 'map("\(.[0]):\(.[1])") | join(" ")') + dcb app del dev $port dscp-prio $prio_str + + echo "Restoring original DSCP priorities for $port" + local restore_str=$(echo "$original_prios" | + jq -r 'map("\(.[0]):\(.[1])") | join(" ")') + dcb app add dev $port dscp-prio $restore_str + + local current_prios=$(get_dscp_prios $port) + if [[ "$original_prios" != "$current_prios" ]]; then + echo "Error: Failed to restore original DSCP priorities for $port" + return 1 + fi + return 0 +} + +# Initialize DSCP priorities. Set them to predictable values for testing. +init_dscp_prios() { + local port=$1 + local original_prios=$2 + + echo "Removing any existing DSCP priority mappins for $port" + local prio_str=$(echo "$original_prios" | + jq -r 'map("\(.[0]):\(.[1])") | join(" ")') + dcb app del dev $port dscp-prio $prio_str + + # Initialize DSCP priorities list + local dscp_prios="" + for dscp in {0..63}; do + dscp_prios+=("$dscp:0") + done + + echo "Setting initial DSCP priorities map to 0 for $port" + dcb app add dev $port dscp-prio ${dscp_prios[@]} +} + +# Main function to test global DSCP map across specified ports +test_global_dscp_map() { + local ports=("$swp1" "$swp2") + local original_dscp_prios_port0=$(get_dscp_prios ${ports[0]}) + local orig_apptrust=$(port_get_default_apptrust ${swp1}) + local orig_port_prio=$(port_default_prio_get ${swp1}) + local apptrust_order="dscp" + local port_prio=0 + local dscp_prio + local dscp + + RET=0 + + set_apptrust_order ${swp1} "${apptrust_order}" + dcb app replace dev ${swp1} default-prio ${port_prio} + + # Initialize DSCP priorities + init_dscp_prios "${ports[0]}" "$original_dscp_prios_port0" + + # Loop over each DSCP index + for dscp in {0..63}; do + # and test each Internal Priority value + for dscp_prio in {0..7}; do + # do it for each port. This is to test if the global DSCP map + # is accessible from all ports. + for port in "${ports[@]}"; do + if ! set_and_verify_dscp "$port" $dscp $dscp_prio; then + RET=1 + fi + done + + # Test if the DSCP priority is correctly applied to the packets + run_test_dscp "DSCP (${dscp}) QoS classification, prio: ${dscp_prio}" \ + "${apptrust_order}" ${port_prio} ${dscp_prio} ${dscp} + if [ ${RET} -eq 1 ]; then + break + fi + done + done + + # Restore original priorities + if ! restore_priorities "${ports[0]}" "${original_dscp_prios_port0}"; then + RET=1 + fi + + set_apptrust_order ${swp1} "${orig_apptrust}" + if [[ "$orig_apptrust" != "$(port_get_default_apptrust ${swp1})" ]]; then + RET=1 + fi + + dcb app replace dev ${swp1} default-prio ${orig_port_prio} + if [ $orig_port_prio -ne $(port_default_prio_get ${swp1}) ]; then + RET=1 + fi + + log_test "DSCP global map" +} + +trap cleanup EXIT + +ALL_TESTS=" + test_port_default + test_port_apptrust + test_global_dscp_map +" + +setup_prepare +setup_wait +tests_run + +exit $EXIT_STATUS