| Message ID | 20240505164549.65644-6-linux@fw-web.de (mailing list archive) |
|---|---|
| State | Superseded |
| Headers | show |
| Series | Add Bananapi R3 Mini | expand |
| Context | Check | Description |
|---|---|---|
| netdev/tree_selection | success | Not a local patch |
On 05/05/2024 18:45, Frank Wunderlich wrote: > From: Frank Wunderlich <frank-w@public-files.de> > > Add device Tree for Bananapi R3 Mini SBC. > > Co-developed-by: Eric Woudstra <ericwouds@gmail.com> > Signed-off-by: Eric Woudstra <ericwouds@gmail.com> > Co-developed-by: Tianling Shen <cnsztl@gmail.com> > Signed-off-by: Tianling Shen <cnsztl@gmail.com> > Signed-off-by: Frank Wunderlich <frank-w@public-files.de> > --- > arch/arm64/boot/dts/mediatek/Makefile | 1 + > .../mediatek/mt7986a-bananapi-bpi-r3-mini.dts | 486 ++++++++++++++++++ > 2 files changed, 487 insertions(+) > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile > index 37b4ca3a87c9..1763b001ab06 100644 > --- a/arch/arm64/boot/dts/mediatek/Makefile > +++ b/arch/arm64/boot/dts/mediatek/Makefile > @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > new file mode 100644 > index 000000000000..c764b4dc4752 > --- /dev/null > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > @@ -0,0 +1,486 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +/* > + * Copyright (C) 2021 MediaTek Inc. > + * Authors: Frank Wunderlich <frank-w@public-files.de> > + * Eric Woudstra <ericwouds@gmail.com> > + * Tianling Shen <cnsztl@immortalwrt.org> > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/mt65xx.h> > + > +#include "mt7986a.dtsi" > + > +/ { > + model = "Bananapi BPI-R3 Mini"; > + chassis-type = "embedded"; > + compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a"; > + > + aliases { > + serial0 = &uart0; > + ethernet0 = &gmac0; > + ethernet1 = &gmac1; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + dcin: regulator-12vd { Please use name for all fixed regulators which matches current format recommendation: 'regulator-[0-9]+v[0-9]+' https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git/commit/?id=b6d4b3500d57370f5b3abf0701c9166b384db976 > + compatible = "regulator-fixed"; > + regulator-name = "12vd"; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + fan: pwm-fan { > + compatible = "pwm-fan"; > + #cooling-cells = <2>; > + /* cooling level (0, 1, 2) - pwm inverted */ > + cooling-levels = <255 96 0>; > + pwms = <&pwm 0 10000>; > + status = "okay"; Why? Where is it disabled? > + }; > + > + reg_1p8v: regulator-1p8v { Please use name for all fixed regulators which matches current format recommendation: 'regulator-[0-9]+v[0-9]+' https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git/commit/?id=b6d4b3500d57370f5b3abf0701c9166b384db976 In other places as well. Best regards, Krzysztof
Il 05/05/24 18:45, Frank Wunderlich ha scritto: > From: Frank Wunderlich <frank-w@public-files.de> > > Add device Tree for Bananapi R3 Mini SBC. > > Co-developed-by: Eric Woudstra <ericwouds@gmail.com> > Signed-off-by: Eric Woudstra <ericwouds@gmail.com> > Co-developed-by: Tianling Shen <cnsztl@gmail.com> > Signed-off-by: Tianling Shen <cnsztl@gmail.com> > Signed-off-by: Frank Wunderlich <frank-w@public-files.de> > --- > arch/arm64/boot/dts/mediatek/Makefile | 1 + > .../mediatek/mt7986a-bananapi-bpi-r3-mini.dts | 486 ++++++++++++++++++ > 2 files changed, 487 insertions(+) > create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > > diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile > index 37b4ca3a87c9..1763b001ab06 100644 > --- a/arch/arm64/boot/dts/mediatek/Makefile > +++ b/arch/arm64/boot/dts/mediatek/Makefile > @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb > +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo > dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo > diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > new file mode 100644 > index 000000000000..c764b4dc4752 > --- /dev/null > +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > @@ -0,0 +1,486 @@ > +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > +/* > + * Copyright (C) 2021 MediaTek Inc. > + * Authors: Frank Wunderlich <frank-w@public-files.de> > + * Eric Woudstra <ericwouds@gmail.com> > + * Tianling Shen <cnsztl@immortalwrt.org> > + */ > + > +/dts-v1/; > + > +#include <dt-bindings/gpio/gpio.h> > +#include <dt-bindings/input/input.h> > +#include <dt-bindings/leds/common.h> > +#include <dt-bindings/pinctrl/mt65xx.h> > + > +#include "mt7986a.dtsi" > + > +/ { > + model = "Bananapi BPI-R3 Mini"; > + chassis-type = "embedded"; > + compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a"; > + > + aliases { > + serial0 = &uart0; > + ethernet0 = &gmac0; > + ethernet1 = &gmac1; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + dcin: regulator-12vd { > + compatible = "regulator-fixed"; > + regulator-name = "12vd"; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + regulator-boot-on; > + regulator-always-on; > + }; > + > + fan: pwm-fan { > + compatible = "pwm-fan"; > + #cooling-cells = <2>; > + /* cooling level (0, 1, 2) - pwm inverted */ > + cooling-levels = <255 96 0>; Did you try to actually invert the PWM? Look for PWM_POLARITY_INVERTED ;-) > + pwms = <&pwm 0 10000>; > + status = "okay"; > + }; > + > + reg_1p8v: regulator-1p8v { > + compatible = "regulator-fixed"; > + regulator-name = "1.8vd"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-boot-on; > + regulator-always-on; > + vin-supply = <&dcin>; > + }; > + > + reg_3p3v: regulator-3p3v { > + compatible = "regulator-fixed"; > + regulator-name = "3.3vd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-boot-on; > + regulator-always-on; > + vin-supply = <&dcin>; > + }; > + > + usb_vbus: regulator-usb-vbus { > + compatible = "regulator-fixed"; > + regulator-name = "usb_vbus"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpios = <&pio 20 GPIO_ACTIVE_LOW>; > + regulator-boot-on; > + }; > + > + en8811_a: regulator-phy1 { > + compatible = "regulator-fixed"; > + regulator-name = "phy1"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&pio 16 GPIO_ACTIVE_LOW>; > + regulator-always-on; > + }; > + > + en8811_b: regulator-phy2 { > + compatible = "regulator-fixed"; > + regulator-name = "phy2"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + gpio = <&pio 17 GPIO_ACTIVE_LOW>; > + regulator-always-on; > + }; > + > + leds { > + compatible = "gpio-leds"; > + > + green_led: led-0 { > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_POWER; > + gpios = <&pio 19 GPIO_ACTIVE_HIGH>; > + default-state = "on"; > + }; > + }; > + > + gpio-keys { > + compatible = "gpio-keys"; > + > + reset-key { > + label = "reset"; > + linux,code = <KEY_RESTART>; > + gpios = <&pio 7 GPIO_ACTIVE_LOW>; > + }; > + }; > + > +}; > + > +&cpu_thermal { > + cooling-maps { > + map0 { > + /* active: set fan to cooling level 2 */ > + cooling-device = <&fan 2 2>; > + trip = <&cpu_trip_active_high>; > + }; > + > + map1 { > + /* active: set fan to cooling level 1 */ > + cooling-device = <&fan 1 1>; > + trip = <&cpu_trip_active_med>; > + }; > + > + map2 { > + /* active: set fan to cooling level 0 */ > + cooling-device = <&fan 0 0>; > + trip = <&cpu_trip_active_low>; > + }; > + }; > +}; > + > +&crypto { > + status = "okay"; > +}; > + > +ð { > + status = "okay"; > + > + gmac0: mac@0 { > + compatible = "mediatek,eth-mac"; > + reg = <0>; > + phy-mode = "2500base-x"; > + phy-handle = <&phy14>; > + }; > + > + gmac1: mac@1 { > + compatible = "mediatek,eth-mac"; > + reg = <1>; > + phy-mode = "2500base-x"; > + phy-handle = <&phy15>; > + }; > + > + mdio: mdio-bus { > + #address-cells = <1>; > + #size-cells = <0>; > + }; > +}; > + > +&mmc0 { > + pinctrl-names = "default", "state_uhs"; > + pinctrl-0 = <&mmc0_pins_default>; > + pinctrl-1 = <&mmc0_pins_uhs>; > + vmmc-supply = <®_3p3v>; > + vqmmc-supply = <®_1p8v>; > +}; > + > + > +&i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&i2c_pins>; > + status = "okay"; > + > + /* MAC Address EEPROM */ > + eeprom@50 { > + compatible = "atmel,24c02"; > + reg = <0x50>; > + > + address-width = <8>; > + pagesize = <8>; > + size = <256>; > + }; > +}; > + > +&mdio { You can just move all this stuff to where you declare the mdio-bus.... > + #address-cells = <1>; > + #size-cells = <0>; > + > + phy14: ethernet-phy@14 { I say that this is `phy0: ethernet-phy@14` - because this is the first PHY on this board. > + reg = <14>; Uhm.. doesn't this require the ethernet-phy-id03a2.a411 compatible? > + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; > + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; > + reset-assert-us = <10000>; > + reset-deassert-us = <20000>; > + phy-mode = "2500base-x"; > + full-duplex; > + pause; > + airoha,pnswap-rx; > + > + leds { > + #address-cells = <1>; > + #size-cells = <0>; > + > + led@0 { /* en8811_a_gpio5 */ > + reg = <0>; > + color = <LED_COLOR_ID_YELLOW>; > + function = LED_FUNCTION_LAN; > + function-enumerator = <1>; Why aren't you simply using a label? > + default-state = "keep"; > + linux,default-trigger = "netdev"; > + }; > + led@1 { /* en8811_a_gpio4 */ > + reg = <1>; > + color = <LED_COLOR_ID_GREEN>; > + function = LED_FUNCTION_LAN; > + function-enumerator = <2>; > + default-state = "keep"; > + linux,default-trigger = "netdev"; > + }; > + }; > + }; > + > + phy15: ethernet-phy@15 { > + reg = <15>; Same here. Cheers, Angelo
Hi Thanks for review. Am 6. Mai 2024 14:48:59 MESZ schrieb AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>: >Il 05/05/24 18:45, Frank Wunderlich ha scritto: >> From: Frank Wunderlich <frank-w@public-files.de> >> >> Add device Tree for Bananapi R3 Mini SBC. >> >> Co-developed-by: Eric Woudstra <ericwouds@gmail.com> >> Signed-off-by: Eric Woudstra <ericwouds@gmail.com> >> Co-developed-by: Tianling Shen <cnsztl@gmail.com> >> Signed-off-by: Tianling Shen <cnsztl@gmail.com> >> Signed-off-by: Frank Wunderlich <frank-w@public-files.de> >> --- >> arch/arm64/boot/dts/mediatek/Makefile | 1 + >> .../mediatek/mt7986a-bananapi-bpi-r3-mini.dts | 486 ++++++++++++++++++ >> 2 files changed, 487 insertions(+) >> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts >> >> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile >> index 37b4ca3a87c9..1763b001ab06 100644 >> --- a/arch/arm64/boot/dts/mediatek/Makefile >> +++ b/arch/arm64/boot/dts/mediatek/Makefile >> @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo >> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts >> new file mode 100644 >> index 000000000000..c764b4dc4752 >> --- /dev/null >> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts >> @@ -0,0 +1,486 @@ >> +// SPDX-License-Identifier: (GPL-2.0 OR MIT) >> +/* >> + * Copyright (C) 2021 MediaTek Inc. >> + * Authors: Frank Wunderlich <frank-w@public-files.de> >> + * Eric Woudstra <ericwouds@gmail.com> >> + * Tianling Shen <cnsztl@immortalwrt.org> >> + */ >> + >> +/dts-v1/; >> + >> +#include <dt-bindings/gpio/gpio.h> >> +#include <dt-bindings/input/input.h> >> +#include <dt-bindings/leds/common.h> >> +#include <dt-bindings/pinctrl/mt65xx.h> >> + >> +#include "mt7986a.dtsi" >> + >> +/ { >> + model = "Bananapi BPI-R3 Mini"; >> + chassis-type = "embedded"; >> + compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a"; >> + >> + aliases { >> + serial0 = &uart0; >> + ethernet0 = &gmac0; >> + ethernet1 = &gmac1; >> + }; >> + >> + chosen { >> + stdout-path = "serial0:115200n8"; >> + }; >> + >> + dcin: regulator-12vd { >> + compatible = "regulator-fixed"; >> + regulator-name = "12vd"; >> + regulator-min-microvolt = <12000000>; >> + regulator-max-microvolt = <12000000>; >> + regulator-boot-on; >> + regulator-always-on; >> + }; >> + >> + fan: pwm-fan { >> + compatible = "pwm-fan"; >> + #cooling-cells = <2>; >> + /* cooling level (0, 1, 2) - pwm inverted */ >> + cooling-levels = <255 96 0>; > >Did you try to actually invert the PWM? > >Look for PWM_POLARITY_INVERTED ;-) Mtk pwm driver does not support it https://elixir.bootlin.com/linux/latest/source/drivers/pwm/pwm-mediatek.c#L211 >> + pwms = <&pwm 0 10000>; >> + status = "okay"; >> + }; >> + >> + reg_1p8v: regulator-1p8v { >> + compatible = "regulator-fixed"; >> + regulator-name = "1.8vd"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-boot-on; >> + regulator-always-on; >> + vin-supply = <&dcin>; >> + }; >> + >> + reg_3p3v: regulator-3p3v { >> + compatible = "regulator-fixed"; >> + regulator-name = "3.3vd"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-boot-on; >> + regulator-always-on; >> + vin-supply = <&dcin>; >> + }; >> + >> + usb_vbus: regulator-usb-vbus { >> + compatible = "regulator-fixed"; >> + regulator-name = "usb_vbus"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + gpios = <&pio 20 GPIO_ACTIVE_LOW>; >> + regulator-boot-on; >> + }; >> + >> + en8811_a: regulator-phy1 { >> + compatible = "regulator-fixed"; >> + regulator-name = "phy1"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + gpio = <&pio 16 GPIO_ACTIVE_LOW>; >> + regulator-always-on; >> + }; >> + >> + en8811_b: regulator-phy2 { >> + compatible = "regulator-fixed"; >> + regulator-name = "phy2"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + gpio = <&pio 17 GPIO_ACTIVE_LOW>; >> + regulator-always-on; >> + }; >> + >> + leds { >> + compatible = "gpio-leds"; >> + >> + green_led: led-0 { >> + color = <LED_COLOR_ID_GREEN>; >> + function = LED_FUNCTION_POWER; >> + gpios = <&pio 19 GPIO_ACTIVE_HIGH>; >> + default-state = "on"; >> + }; >> + }; >> + >> + gpio-keys { >> + compatible = "gpio-keys"; >> + >> + reset-key { >> + label = "reset"; >> + linux,code = <KEY_RESTART>; >> + gpios = <&pio 7 GPIO_ACTIVE_LOW>; >> + }; >> + }; >> + >> +}; >> + >> +&cpu_thermal { >> + cooling-maps { >> + map0 { >> + /* active: set fan to cooling level 2 */ >> + cooling-device = <&fan 2 2>; >> + trip = <&cpu_trip_active_high>; >> + }; >> + >> + map1 { >> + /* active: set fan to cooling level 1 */ >> + cooling-device = <&fan 1 1>; >> + trip = <&cpu_trip_active_med>; >> + }; >> + >> + map2 { >> + /* active: set fan to cooling level 0 */ >> + cooling-device = <&fan 0 0>; >> + trip = <&cpu_trip_active_low>; >> + }; >> + }; >> +}; >> + >> +&crypto { >> + status = "okay"; >> +}; >> + >> +ð { >> + status = "okay"; >> + >> + gmac0: mac@0 { >> + compatible = "mediatek,eth-mac"; >> + reg = <0>; >> + phy-mode = "2500base-x"; >> + phy-handle = <&phy14>; >> + }; >> + >> + gmac1: mac@1 { >> + compatible = "mediatek,eth-mac"; >> + reg = <1>; >> + phy-mode = "2500base-x"; >> + phy-handle = <&phy15>; >> + }; >> + >> + mdio: mdio-bus { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + }; >> +}; >> + >> +&mmc0 { >> + pinctrl-names = "default", "state_uhs"; >> + pinctrl-0 = <&mmc0_pins_default>; >> + pinctrl-1 = <&mmc0_pins_uhs>; >> + vmmc-supply = <®_3p3v>; >> + vqmmc-supply = <®_1p8v>; >> +}; >> + >> + >> +&i2c0 { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&i2c_pins>; >> + status = "okay"; >> + >> + /* MAC Address EEPROM */ >> + eeprom@50 { >> + compatible = "atmel,24c02"; >> + reg = <0x50>; >> + >> + address-width = <8>; >> + pagesize = <8>; >> + size = <256>; >> + }; >> +}; >> + >> +&mdio { > >You can just move all this stuff to where you declare the mdio-bus.... Ok,see these 2 lines are already above,so can be dropped here. >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + phy14: ethernet-phy@14 { > >I say that this is `phy0: ethernet-phy@14` - because this is the first PHY on this >board. Ok,i change this and phy15 >> + reg = <14>; > >Uhm.. doesn't this require the ethernet-phy-id03a2.a411 compatible? I can add it,but worked without it. There was a discussion about that and result was we don't need it in board dts,maybe add compatible in binding example. https://patchwork.kernel.org/project/netdevbpf/patch/20240206194751.1901802-2-ericwouds@gmail.com/#25703356 >> + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; >> + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; >> + reset-assert-us = <10000>; >> + reset-deassert-us = <20000>; >> + phy-mode = "2500base-x"; >> + full-duplex; >> + pause; >> + airoha,pnswap-rx; >> + >> + leds { >> + #address-cells = <1>; >> + #size-cells = <0>; >> + >> + led@0 { /* en8811_a_gpio5 */ >> + reg = <0>; >> + color = <LED_COLOR_ID_YELLOW>; >> + function = LED_FUNCTION_LAN; >> + function-enumerator = <1>; > >Why aren't you simply using a label? You mean the comment? I can add it of course like for regulators. >> + default-state = "keep"; >> + linux,default-trigger = "netdev"; >> + }; >> + led@1 { /* en8811_a_gpio4 */ >> + reg = <1>; >> + color = <LED_COLOR_ID_GREEN>; >> + function = LED_FUNCTION_LAN; >> + function-enumerator = <2>; >> + default-state = "keep"; >> + linux,default-trigger = "netdev"; >> + }; >> + }; >> + }; >> + >> + phy15: ethernet-phy@15 { >> + reg = <15>; > >Same here. > >Cheers, >Angelo > regards Frank
On Mon, May 06, 2024 at 06:00:30PM +0200, Frank Wunderlich wrote: > Hi > > Thanks for review. > > Am 6. Mai 2024 14:48:59 MESZ schrieb AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>: > >Il 05/05/24 18:45, Frank Wunderlich ha scritto: > >> From: Frank Wunderlich <frank-w@public-files.de> > >> > >> Add device Tree for Bananapi R3 Mini SBC. > >> > >> Co-developed-by: Eric Woudstra <ericwouds@gmail.com> > >> Signed-off-by: Eric Woudstra <ericwouds@gmail.com> > >> Co-developed-by: Tianling Shen <cnsztl@gmail.com> > >> Signed-off-by: Tianling Shen <cnsztl@gmail.com> > >> Signed-off-by: Frank Wunderlich <frank-w@public-files.de> > >> --- > >> arch/arm64/boot/dts/mediatek/Makefile | 1 + > >> .../mediatek/mt7986a-bananapi-bpi-r3-mini.dts | 486 ++++++++++++++++++ > >> 2 files changed, 487 insertions(+) > >> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > >> > >> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile > >> index 37b4ca3a87c9..1763b001ab06 100644 > >> --- a/arch/arm64/boot/dts/mediatek/Makefile > >> +++ b/arch/arm64/boot/dts/mediatek/Makefile > >> @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb > >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb > >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb > >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb > >> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb > >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo > >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo > >> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo > >> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > >> new file mode 100644 > >> index 000000000000..c764b4dc4752 > >> --- /dev/null > >> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts > >> @@ -0,0 +1,486 @@ > >> +// SPDX-License-Identifier: (GPL-2.0 OR MIT) > >> +/* > >> + * Copyright (C) 2021 MediaTek Inc. > >> + * Authors: Frank Wunderlich <frank-w@public-files.de> > >> + * Eric Woudstra <ericwouds@gmail.com> > >> + * Tianling Shen <cnsztl@immortalwrt.org> > >> + */ > >> + > >> +/dts-v1/; > >> + > >> +#include <dt-bindings/gpio/gpio.h> > >> +#include <dt-bindings/input/input.h> > >> +#include <dt-bindings/leds/common.h> > >> +#include <dt-bindings/pinctrl/mt65xx.h> > >> + > >> +#include "mt7986a.dtsi" > >> + > >> +/ { > >> + model = "Bananapi BPI-R3 Mini"; > >> + chassis-type = "embedded"; > >> + compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a"; > >> + > >> + aliases { > >> + serial0 = &uart0; > >> + ethernet0 = &gmac0; > >> + ethernet1 = &gmac1; > >> + }; > >> + > >> + chosen { > >> + stdout-path = "serial0:115200n8"; > >> + }; > >> + > >> + dcin: regulator-12vd { > >> + compatible = "regulator-fixed"; > >> + regulator-name = "12vd"; > >> + regulator-min-microvolt = <12000000>; > >> + regulator-max-microvolt = <12000000>; > >> + regulator-boot-on; > >> + regulator-always-on; > >> + }; > >> + > >> + fan: pwm-fan { > >> + compatible = "pwm-fan"; > >> + #cooling-cells = <2>; > >> + /* cooling level (0, 1, 2) - pwm inverted */ > >> + cooling-levels = <255 96 0>; > > > >Did you try to actually invert the PWM? > > > >Look for PWM_POLARITY_INVERTED ;-) > > Mtk pwm driver does not support it > > https://elixir.bootlin.com/linux/latest/source/drivers/pwm/pwm-mediatek.c#L211 > > >> + pwms = <&pwm 0 10000>; > >> + status = "okay"; > >> + }; > >> + > >> + reg_1p8v: regulator-1p8v { > >> + compatible = "regulator-fixed"; > >> + regulator-name = "1.8vd"; > >> + regulator-min-microvolt = <1800000>; > >> + regulator-max-microvolt = <1800000>; > >> + regulator-boot-on; > >> + regulator-always-on; > >> + vin-supply = <&dcin>; > >> + }; > >> + > >> + reg_3p3v: regulator-3p3v { > >> + compatible = "regulator-fixed"; > >> + regulator-name = "3.3vd"; > >> + regulator-min-microvolt = <3300000>; > >> + regulator-max-microvolt = <3300000>; > >> + regulator-boot-on; > >> + regulator-always-on; > >> + vin-supply = <&dcin>; > >> + }; > >> + > >> + usb_vbus: regulator-usb-vbus { > >> + compatible = "regulator-fixed"; > >> + regulator-name = "usb_vbus"; > >> + regulator-min-microvolt = <5000000>; > >> + regulator-max-microvolt = <5000000>; > >> + gpios = <&pio 20 GPIO_ACTIVE_LOW>; > >> + regulator-boot-on; > >> + }; > >> + > >> + en8811_a: regulator-phy1 { > >> + compatible = "regulator-fixed"; > >> + regulator-name = "phy1"; > >> + regulator-min-microvolt = <3300000>; > >> + regulator-max-microvolt = <3300000>; > >> + gpio = <&pio 16 GPIO_ACTIVE_LOW>; > >> + regulator-always-on; > >> + }; > >> + > >> + en8811_b: regulator-phy2 { > >> + compatible = "regulator-fixed"; > >> + regulator-name = "phy2"; > >> + regulator-min-microvolt = <3300000>; > >> + regulator-max-microvolt = <3300000>; > >> + gpio = <&pio 17 GPIO_ACTIVE_LOW>; > >> + regulator-always-on; > >> + }; > >> + > >> + leds { > >> + compatible = "gpio-leds"; > >> + > >> + green_led: led-0 { > >> + color = <LED_COLOR_ID_GREEN>; > >> + function = LED_FUNCTION_POWER; > >> + gpios = <&pio 19 GPIO_ACTIVE_HIGH>; > >> + default-state = "on"; > >> + }; > >> + }; > >> + > >> + gpio-keys { > >> + compatible = "gpio-keys"; > >> + > >> + reset-key { > >> + label = "reset"; > >> + linux,code = <KEY_RESTART>; > >> + gpios = <&pio 7 GPIO_ACTIVE_LOW>; > >> + }; > >> + }; > >> + > >> +}; > >> + > >> +&cpu_thermal { > >> + cooling-maps { > >> + map0 { > >> + /* active: set fan to cooling level 2 */ > >> + cooling-device = <&fan 2 2>; > >> + trip = <&cpu_trip_active_high>; > >> + }; > >> + > >> + map1 { > >> + /* active: set fan to cooling level 1 */ > >> + cooling-device = <&fan 1 1>; > >> + trip = <&cpu_trip_active_med>; > >> + }; > >> + > >> + map2 { > >> + /* active: set fan to cooling level 0 */ > >> + cooling-device = <&fan 0 0>; > >> + trip = <&cpu_trip_active_low>; > >> + }; > >> + }; > >> +}; > >> + > >> +&crypto { > >> + status = "okay"; > >> +}; > >> + > >> +ð { > >> + status = "okay"; > >> + > >> + gmac0: mac@0 { > >> + compatible = "mediatek,eth-mac"; > >> + reg = <0>; > >> + phy-mode = "2500base-x"; > >> + phy-handle = <&phy14>; > >> + }; > >> + > >> + gmac1: mac@1 { > >> + compatible = "mediatek,eth-mac"; > >> + reg = <1>; > >> + phy-mode = "2500base-x"; > >> + phy-handle = <&phy15>; > >> + }; > >> + > >> + mdio: mdio-bus { > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + }; > >> +}; > >> + > >> +&mmc0 { > >> + pinctrl-names = "default", "state_uhs"; > >> + pinctrl-0 = <&mmc0_pins_default>; > >> + pinctrl-1 = <&mmc0_pins_uhs>; > >> + vmmc-supply = <®_3p3v>; > >> + vqmmc-supply = <®_1p8v>; > >> +}; > >> + > >> + > >> +&i2c0 { > >> + pinctrl-names = "default"; > >> + pinctrl-0 = <&i2c_pins>; > >> + status = "okay"; > >> + > >> + /* MAC Address EEPROM */ > >> + eeprom@50 { > >> + compatible = "atmel,24c02"; > >> + reg = <0x50>; > >> + > >> + address-width = <8>; > >> + pagesize = <8>; > >> + size = <256>; > >> + }; > >> +}; > >> + > >> +&mdio { > > > >You can just move all this stuff to where you declare the mdio-bus.... > > Ok,see these 2 lines are already above,so can be dropped here. > > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + > >> + phy14: ethernet-phy@14 { > > > >I say that this is `phy0: ethernet-phy@14` - because this is the first PHY on this > >board. > > Ok,i change this and phy15 > > >> + reg = <14>; > > > >Uhm.. doesn't this require the ethernet-phy-id03a2.a411 compatible? > > I can add it,but worked without it. > > There was a discussion about that and result was we don't need it in board dts,maybe add compatible in binding example. > > https://patchwork.kernel.org/project/netdevbpf/patch/20240206194751.1901802-2-ericwouds@gmail.com/#25703356 I confirm that setting the PHY ID in DT is **not** needed. The PHY probes fine and it's possible to read the PHY ID even before firmware has been loaded. > > >> + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; > >> + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; > >> + reset-assert-us = <10000>; > >> + reset-deassert-us = <20000>; > >> + phy-mode = "2500base-x"; > >> + full-duplex; > >> + pause; > >> + airoha,pnswap-rx; > >> + > >> + leds { > >> + #address-cells = <1>; > >> + #size-cells = <0>; > >> + > >> + led@0 { /* en8811_a_gpio5 */ > >> + reg = <0>; > >> + color = <LED_COLOR_ID_YELLOW>; > >> + function = LED_FUNCTION_LAN; > >> + function-enumerator = <1>; > > > >Why aren't you simply using a label? > > You mean the comment? I can add it of course like for regulators. > > >> + default-state = "keep"; > >> + linux,default-trigger = "netdev"; Using linux,default-trigger = "netdev" will NOT work as intended, see also the reply to your other patch where you are adding netdev trigger to dt-bindings. If you do this, it will seemingly work, but if you check /sys/class/leds/foo/hw_control it will always be 0, and hardware offloading will hence never be used. Please just set the LED trigger in userspace for now. > >> + }; > >> + led@1 { /* en8811_a_gpio4 */ > >> + reg = <1>; > >> + color = <LED_COLOR_ID_GREEN>; > >> + function = LED_FUNCTION_LAN; > >> + function-enumerator = <2>; > >> + default-state = "keep"; > >> + linux,default-trigger = "netdev"; > >> + }; > >> + }; > >> + }; > >> + > >> + phy15: ethernet-phy@15 { > >> + reg = <15>; > > > >Same here. > > > >Cheers, > >Angelo > > > > > regards Frank >
Hi Thanks for review > Gesendet: Montag, 06. Mai 2024 um 10:20 Uhr > Von: "Krzysztof Kozlowski" <krzysztof.kozlowski@linaro.org> > An: "Frank Wunderlich" <linux@fw-web.de>, "Rob Herring" <robh@kernel.org>, "Krzysztof Kozlowski" > > + dcin: regulator-12vd { > > Please use name for all fixed regulators which matches current format > recommendation: 'regulator-[0-9]+v[0-9]+' > > https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git/commit/?id=b6d4b3500d57370f5b3abf0701c9166b384db976 > > > + compatible = "regulator-fixed"; > > + regulator-name = "12vd"; > > + regulator-min-microvolt = <12000000>; > > + regulator-max-microvolt = <12000000>; > > + regulator-boot-on; > > + regulator-always-on; > > + }; > > + > > + fan: pwm-fan { > > + compatible = "pwm-fan"; > > + #cooling-cells = <2>; > > + /* cooling level (0, 1, 2) - pwm inverted */ > > + cooling-levels = <255 96 0>; > > + pwms = <&pwm 0 10000>; > > + status = "okay"; > > Why? Where is it disabled? you're right, i'll drop it > > + }; > > + > > + reg_1p8v: regulator-1p8v { > > Please use name for all fixed regulators which matches current format > recommendation: 'regulator-[0-9]+v[0-9]+' > > https://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator.git/commit/?id=b6d4b3500d57370f5b3abf0701c9166b384db976 > > In other places as well. ok i change it like this (label doesn't matter, right?): dcin: regulator-12v { reg_1p8v: regulator-1v8 { reg_3p3v: regulator-3v3 { usb_vbus: regulator-5v { > Best regards, > Krzysztof regards Frank
Il 06/05/24 18:00, Frank Wunderlich ha scritto: > Hi > > Thanks for review. > > Am 6. Mai 2024 14:48:59 MESZ schrieb AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>: >> Il 05/05/24 18:45, Frank Wunderlich ha scritto: >>> From: Frank Wunderlich <frank-w@public-files.de> >>> >>> Add device Tree for Bananapi R3 Mini SBC. >>> >>> Co-developed-by: Eric Woudstra <ericwouds@gmail.com> >>> Signed-off-by: Eric Woudstra <ericwouds@gmail.com> >>> Co-developed-by: Tianling Shen <cnsztl@gmail.com> >>> Signed-off-by: Tianling Shen <cnsztl@gmail.com> >>> Signed-off-by: Frank Wunderlich <frank-w@public-files.de> >>> --- >>> arch/arm64/boot/dts/mediatek/Makefile | 1 + >>> .../mediatek/mt7986a-bananapi-bpi-r3-mini.dts | 486 ++++++++++++++++++ >>> 2 files changed, 487 insertions(+) >>> create mode 100644 arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts >>> >>> diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile >>> index 37b4ca3a87c9..1763b001ab06 100644 >>> --- a/arch/arm64/boot/dts/mediatek/Makefile >>> +++ b/arch/arm64/boot/dts/mediatek/Makefile >>> @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb >>> +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo >>> dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo >>> diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts >>> new file mode 100644 >>> index 000000000000..c764b4dc4752 >>> --- /dev/null >>> +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts >>> @@ -0,0 +1,486 @@ >>> +// SPDX-License-Identifier: (GPL-2.0 OR MIT) >>> +/* >>> + * Copyright (C) 2021 MediaTek Inc. >>> + * Authors: Frank Wunderlich <frank-w@public-files.de> >>> + * Eric Woudstra <ericwouds@gmail.com> >>> + * Tianling Shen <cnsztl@immortalwrt.org> >>> + */ >>> + >>> +/dts-v1/; >>> + >>> +#include <dt-bindings/gpio/gpio.h> >>> +#include <dt-bindings/input/input.h> >>> +#include <dt-bindings/leds/common.h> >>> +#include <dt-bindings/pinctrl/mt65xx.h> >>> + >>> +#include "mt7986a.dtsi" >>> + >>> +/ { >>> + model = "Bananapi BPI-R3 Mini"; >>> + chassis-type = "embedded"; >>> + compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a"; >>> + >>> + aliases { >>> + serial0 = &uart0; >>> + ethernet0 = &gmac0; >>> + ethernet1 = &gmac1; >>> + }; >>> + >>> + chosen { >>> + stdout-path = "serial0:115200n8"; >>> + }; >>> + >>> + dcin: regulator-12vd { >>> + compatible = "regulator-fixed"; >>> + regulator-name = "12vd"; >>> + regulator-min-microvolt = <12000000>; >>> + regulator-max-microvolt = <12000000>; >>> + regulator-boot-on; >>> + regulator-always-on; >>> + }; >>> + >>> + fan: pwm-fan { >>> + compatible = "pwm-fan"; >>> + #cooling-cells = <2>; >>> + /* cooling level (0, 1, 2) - pwm inverted */ >>> + cooling-levels = <255 96 0>; >> >> Did you try to actually invert the PWM? >> >> Look for PWM_POLARITY_INVERTED ;-) > > Mtk pwm driver does not support it > > https://elixir.bootlin.com/linux/latest/source/drivers/pwm/pwm-mediatek.c#L211 > You're right, sorry - I confused the general purpose PWM controller with the rather specific DISP_PWM controller (which does support polarity inversion). It's good - but I'd appreciate if you can please add a comment stating that the PWM values are inverted in SW because the controller does *not* support polarity inversion... so that next time someone looks at this will immediately understand what's going on and why :-) >>> + pwms = <&pwm 0 10000>; >>> + status = "okay"; >>> + }; >>> + >>> + reg_1p8v: regulator-1p8v { >>> + compatible = "regulator-fixed"; >>> + regulator-name = "1.8vd"; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-boot-on; >>> + regulator-always-on; >>> + vin-supply = <&dcin>; >>> + }; >>> + >>> + reg_3p3v: regulator-3p3v { >>> + compatible = "regulator-fixed"; >>> + regulator-name = "3.3vd"; >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + regulator-boot-on; >>> + regulator-always-on; >>> + vin-supply = <&dcin>; >>> + }; >>> + >>> + usb_vbus: regulator-usb-vbus { >>> + compatible = "regulator-fixed"; >>> + regulator-name = "usb_vbus"; >>> + regulator-min-microvolt = <5000000>; >>> + regulator-max-microvolt = <5000000>; >>> + gpios = <&pio 20 GPIO_ACTIVE_LOW>; >>> + regulator-boot-on; >>> + }; >>> + >>> + en8811_a: regulator-phy1 { >>> + compatible = "regulator-fixed"; >>> + regulator-name = "phy1"; >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + gpio = <&pio 16 GPIO_ACTIVE_LOW>; >>> + regulator-always-on; >>> + }; >>> + >>> + en8811_b: regulator-phy2 { >>> + compatible = "regulator-fixed"; >>> + regulator-name = "phy2"; >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + gpio = <&pio 17 GPIO_ACTIVE_LOW>; >>> + regulator-always-on; >>> + }; >>> + >>> + leds { >>> + compatible = "gpio-leds"; >>> + >>> + green_led: led-0 { >>> + color = <LED_COLOR_ID_GREEN>; >>> + function = LED_FUNCTION_POWER; >>> + gpios = <&pio 19 GPIO_ACTIVE_HIGH>; >>> + default-state = "on"; >>> + }; >>> + }; >>> + >>> + gpio-keys { >>> + compatible = "gpio-keys"; >>> + >>> + reset-key { >>> + label = "reset"; >>> + linux,code = <KEY_RESTART>; >>> + gpios = <&pio 7 GPIO_ACTIVE_LOW>; >>> + }; >>> + }; >>> + >>> +}; >>> + >>> +&cpu_thermal { >>> + cooling-maps { >>> + map0 { >>> + /* active: set fan to cooling level 2 */ >>> + cooling-device = <&fan 2 2>; >>> + trip = <&cpu_trip_active_high>; >>> + }; >>> + >>> + map1 { >>> + /* active: set fan to cooling level 1 */ >>> + cooling-device = <&fan 1 1>; >>> + trip = <&cpu_trip_active_med>; >>> + }; >>> + >>> + map2 { >>> + /* active: set fan to cooling level 0 */ >>> + cooling-device = <&fan 0 0>; >>> + trip = <&cpu_trip_active_low>; >>> + }; >>> + }; >>> +}; >>> + >>> +&crypto { >>> + status = "okay"; >>> +}; >>> + >>> +ð { >>> + status = "okay"; >>> + >>> + gmac0: mac@0 { >>> + compatible = "mediatek,eth-mac"; >>> + reg = <0>; >>> + phy-mode = "2500base-x"; >>> + phy-handle = <&phy14>; >>> + }; >>> + >>> + gmac1: mac@1 { >>> + compatible = "mediatek,eth-mac"; >>> + reg = <1>; >>> + phy-mode = "2500base-x"; >>> + phy-handle = <&phy15>; >>> + }; >>> + >>> + mdio: mdio-bus { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + }; >>> +}; >>> + >>> +&mmc0 { >>> + pinctrl-names = "default", "state_uhs"; >>> + pinctrl-0 = <&mmc0_pins_default>; >>> + pinctrl-1 = <&mmc0_pins_uhs>; >>> + vmmc-supply = <®_3p3v>; >>> + vqmmc-supply = <®_1p8v>; >>> +}; >>> + >>> + >>> +&i2c0 { >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&i2c_pins>; >>> + status = "okay"; >>> + >>> + /* MAC Address EEPROM */ >>> + eeprom@50 { >>> + compatible = "atmel,24c02"; >>> + reg = <0x50>; >>> + >>> + address-width = <8>; >>> + pagesize = <8>; >>> + size = <256>; >>> + }; >>> +}; >>> + >>> +&mdio { >> >> You can just move all this stuff to where you declare the mdio-bus.... > > Ok,see these 2 lines are already above,so can be dropped here. > >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + phy14: ethernet-phy@14 { >> >> I say that this is `phy0: ethernet-phy@14` - because this is the first PHY on this >> board. > > Ok,i change this and phy15 > >>> + reg = <14>; >> >> Uhm.. doesn't this require the ethernet-phy-id03a2.a411 compatible? > > I can add it,but worked without it. > > There was a discussion about that and result was we don't need it in board dts,maybe add compatible in binding example. > > https://patchwork.kernel.org/project/netdevbpf/patch/20240206194751.1901802-2-ericwouds@gmail.com/#25703356 > Ah, okay. Leave it then. >>> + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; >>> + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; >>> + reset-assert-us = <10000>; >>> + reset-deassert-us = <20000>; >>> + phy-mode = "2500base-x"; >>> + full-duplex; >>> + pause; >>> + airoha,pnswap-rx; >>> + >>> + leds { >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + >>> + led@0 { /* en8811_a_gpio5 */ >>> + reg = <0>; >>> + color = <LED_COLOR_ID_YELLOW>; >>> + function = LED_FUNCTION_LAN; >>> + function-enumerator = <1>; >> >> Why aren't you simply using a label? > > You mean the comment? I can add it of course like for regulators. > I mean in place of the function-enumerator... that's practically used to distinguish between instances, it's not too common to see it, and usually "label" replaces exactly that - just that, instead of a different number, it gets a different name with no (usually) meaningless numbers :-) Cheers! >>> + default-state = "keep"; >>> + linux,default-trigger = "netdev"; >>> + }; >>> + led@1 { /* en8811_a_gpio4 */ >>> + reg = <1>; >>> + color = <LED_COLOR_ID_GREEN>; >>> + function = LED_FUNCTION_LAN; >>> + function-enumerator = <2>; >>> + default-state = "keep"; >>> + linux,default-trigger = "netdev"; >>> + }; >>> + }; >>> + }; >>> + >>> + phy15: ethernet-phy@15 { >>> + reg = <15>; >> >> Same here. >> >> Cheers, >> Angelo >> > > > regards Frank
Hi > Gesendet: Dienstag, 07. Mai 2024 um 15:35 Uhr > Von: "AngeloGioacchino Del Regno" <angelogioacchino.delregno@collabora.com> > > Il 06/05/24 18:00, Frank Wunderlich ha scritto: > >>> + fan: pwm-fan { > >>> + compatible = "pwm-fan"; > >>> + #cooling-cells = <2>; > >>> + /* cooling level (0, 1, 2) - pwm inverted */ > >>> + cooling-levels = <255 96 0>; > >> > >> Did you try to actually invert the PWM? > >> > >> Look for PWM_POLARITY_INVERTED ;-) > > > > Mtk pwm driver does not support it > > > > https://elixir.bootlin.com/linux/latest/source/drivers/pwm/pwm-mediatek.c#L211 > > > > You're right, sorry - I confused the general purpose PWM controller with the > rather specific DISP_PWM controller (which does support polarity inversion). > > It's good - but I'd appreciate if you can please add a comment stating that > the PWM values are inverted in SW because the controller does *not* support > polarity inversion... so that next time someone looks at this will immediately > understand what's going on and why :-) so i would change comment like this: /* cooling level (0, 1, 2) * signal is inverted on board * mtk pwm driver does not support * PWM_POLARITY_INVERTED */ > >>> + pwms = <&pwm 0 10000>; > >>> + status = "okay"; > >>> + }; > >>> + > >>> + phy14: ethernet-phy@14 { ... > >>> + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; > >>> + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; > >>> + reset-assert-us = <10000>; > >>> + reset-deassert-us = <20000>; > >>> + phy-mode = "2500base-x"; > >>> + full-duplex; > >>> + pause; > >>> + airoha,pnswap-rx; > >>> + > >>> + leds { > >>> + #address-cells = <1>; > >>> + #size-cells = <0>; > >>> + > >>> + led@0 { /* en8811_a_gpio5 */ > >>> + reg = <0>; > >>> + color = <LED_COLOR_ID_YELLOW>; > >>> + function = LED_FUNCTION_LAN; > >>> + function-enumerator = <1>; > >> > >> Why aren't you simply using a label? > > > > You mean the comment? I can add it of course like for regulators. > > > > I mean in place of the function-enumerator... that's practically used to > distinguish between instances, it's not too common to see it, and usually > "label" replaces exactly that - just that, instead of a different number, > it gets a different name with no (usually) meaningless numbers :-) as far as i understand using label also makes "function" property useless, after discussing this with eric i would drop both on all 4 places by labels like these: label = "yellow-lan"; label = "green-lan"; ... not sure if we should drop color property too... > >>> + default-state = "keep"; > >>> + linux,default-trigger = "netdev"; > >>> + }; > >>> + led@1 { /* en8811_a_gpio4 */ > >>> + reg = <1>; > >>> + color = <LED_COLOR_ID_GREEN>; > >>> + function = LED_FUNCTION_LAN; > >>> + function-enumerator = <2>; > >>> + default-state = "keep"; > >>> + linux,default-trigger = "netdev"; > >>> + }; > >>> + }; > >>> + }; > >>> + > >>> + phy15: ethernet-phy@15 { > >>> + reg = <15>; > >> > >> Same here. > >> > >> Cheers, > >> Angelo regards Frank
Il 08/05/24 20:25, Frank Wunderlich ha scritto: > Hi > >> Gesendet: Dienstag, 07. Mai 2024 um 15:35 Uhr >> Von: "AngeloGioacchino Del Regno" <angelogioacchino.delregno@collabora.com> >> >> Il 06/05/24 18:00, Frank Wunderlich ha scritto: > >>>>> + fan: pwm-fan { >>>>> + compatible = "pwm-fan"; >>>>> + #cooling-cells = <2>; >>>>> + /* cooling level (0, 1, 2) - pwm inverted */ >>>>> + cooling-levels = <255 96 0>; >>>> >>>> Did you try to actually invert the PWM? >>>> >>>> Look for PWM_POLARITY_INVERTED ;-) >>> >>> Mtk pwm driver does not support it >>> >>> https://elixir.bootlin.com/linux/latest/source/drivers/pwm/pwm-mediatek.c#L211 >>> >> >> You're right, sorry - I confused the general purpose PWM controller with the >> rather specific DISP_PWM controller (which does support polarity inversion). >> >> It's good - but I'd appreciate if you can please add a comment stating that >> the PWM values are inverted in SW because the controller does *not* support >> polarity inversion... so that next time someone looks at this will immediately >> understand what's going on and why :-) > > so i would change comment like this: > > /* cooling level (0, 1, 2) > * signal is inverted on board > * mtk pwm driver does not support > * PWM_POLARITY_INVERTED */ > There you go: /* * The signal is inverted on this board and the general purpose * PWM HW IP in this SoC does not support polarity inversion. */ /* Cooling level < 0 1 2> */ cooling-levels = <255 96 0>; >>>>> + pwms = <&pwm 0 10000>; >>>>> + status = "okay"; >>>>> + }; >>>>> + >>>>> + phy14: ethernet-phy@14 { > ... >>>>> + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; >>>>> + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; >>>>> + reset-assert-us = <10000>; >>>>> + reset-deassert-us = <20000>; >>>>> + phy-mode = "2500base-x"; >>>>> + full-duplex; >>>>> + pause; >>>>> + airoha,pnswap-rx; >>>>> + >>>>> + leds { >>>>> + #address-cells = <1>; >>>>> + #size-cells = <0>; >>>>> + >>>>> + led@0 { /* en8811_a_gpio5 */ >>>>> + reg = <0>; >>>>> + color = <LED_COLOR_ID_YELLOW>; >>>>> + function = LED_FUNCTION_LAN; >>>>> + function-enumerator = <1>; >>>> >>>> Why aren't you simply using a label? >>> >>> You mean the comment? I can add it of course like for regulators. >>> >> >> I mean in place of the function-enumerator... that's practically used to >> distinguish between instances, it's not too common to see it, and usually >> "label" replaces exactly that - just that, instead of a different number, >> it gets a different name with no (usually) meaningless numbers :-) > > as far as i understand using label also makes "function" property useless, after discussing > this with eric i would drop both on all 4 places by labels like these: > > label = "yellow-lan"; > label = "green-lan"; > ... > > not sure if we should drop color property too... > I'm looking at the leds binding (leds/common.yaml) right now. My suggestion of using 'label' was actually wrong - and your devicetree was actually right!!! (apart from the default-trigger that may not work) Infact, the documentation says, in brief: - function-enumerator is ignored if label is present - function doesn't say that gets ignored - color doesn't say that gets ignored - label says: - If not present -> get string from node name - function-enumerator ignored - This property is deprecated ...but the 'label' binding does not say 'deprecated: true', which is something that must be fixed! So, I'm sorry for the confusion, the noise and the useless loss of time around this - you can keep the LED nodes as they are, and that's a lesson for the future me reviewing another node like this one. P.S.: This shouldn't have been a RFC, as the patches are more than RFC quality!!! Cheers, Angelo >>>>> + default-state = "keep"; >>>>> + linux,default-trigger = "netdev"; >>>>> + }; >>>>> + led@1 { /* en8811_a_gpio4 */ >>>>> + reg = <1>; >>>>> + color = <LED_COLOR_ID_GREEN>; >>>>> + function = LED_FUNCTION_LAN; >>>>> + function-enumerator = <2>; >>>>> + default-state = "keep"; >>>>> + linux,default-trigger = "netdev"; >>>>> + }; >>>>> + }; >>>>> + }; >>>>> + >>>>> + phy15: ethernet-phy@15 { >>>>> + reg = <15>; >>>> >>>> Same here. >>>> >>>> Cheers, >>>> Angelo > > regards Frank
Am 9. Mai 2024 12:10:59 MESZ schrieb AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>: >Il 08/05/24 20:25, Frank Wunderlich ha scritto: >> Hi >> >>> Gesendet: Dienstag, 07. Mai 2024 um 15:35 Uhr >>> Von: "AngeloGioacchino Del Regno" <angelogioacchino.delregno@collabora.com> >>> >>> Il 06/05/24 18:00, Frank Wunderlich ha scritto: >> >>>>>> + fan: pwm-fan { >>>>>> + compatible = "pwm-fan"; >>>>>> + #cooling-cells = <2>; >>>>>> + /* cooling level (0, 1, 2) - pwm inverted */ >>>>>> + cooling-levels = <255 96 0>; >>>>> >>>>> Did you try to actually invert the PWM? >>>>> >>>>> Look for PWM_POLARITY_INVERTED ;-) >>>> >>>> Mtk pwm driver does not support it >>>> >>>> https://elixir.bootlin.com/linux/latest/source/drivers/pwm/pwm-mediatek.c#L211 >>>> >>> >>> You're right, sorry - I confused the general purpose PWM controller with the >>> rather specific DISP_PWM controller (which does support polarity inversion). >>> >>> It's good - but I'd appreciate if you can please add a comment stating that >>> the PWM values are inverted in SW because the controller does *not* support >>> polarity inversion... so that next time someone looks at this will immediately >>> understand what's going on and why :-) >> >> so i would change comment like this: >> >> /* cooling level (0, 1, 2) >> * signal is inverted on board >> * mtk pwm driver does not support >> * PWM_POLARITY_INVERTED */ >> > >There you go: > >/* > * The signal is inverted on this board and the general purpose > * PWM HW IP in this SoC does not support polarity inversion. > */ >/* Cooling level < 0 1 2> */ >cooling-levels = <255 96 0>; Thanks for clearing structure of the comment,but imho actually it is a driver issue (for all mtk SoC). Not sure it is really a hardware limitation. So i would change this to "... and the PWM driver does not support polarity inversion." >>>>>> + pwms = <&pwm 0 10000>; >>>>>> + status = "okay"; >>>>>> + }; >>>>>> + >>>>>> + phy14: ethernet-phy@14 { >> ... >>>>>> + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; >>>>>> + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; >>>>>> + reset-assert-us = <10000>; >>>>>> + reset-deassert-us = <20000>; >>>>>> + phy-mode = "2500base-x"; >>>>>> + full-duplex; >>>>>> + pause; >>>>>> + airoha,pnswap-rx; >>>>>> + >>>>>> + leds { >>>>>> + #address-cells = <1>; >>>>>> + #size-cells = <0>; >>>>>> + >>>>>> + led@0 { /* en8811_a_gpio5 */ >>>>>> + reg = <0>; >>>>>> + color = <LED_COLOR_ID_YELLOW>; >>>>>> + function = LED_FUNCTION_LAN; >>>>>> + function-enumerator = <1>; >>>>> >>>>> Why aren't you simply using a label? >>>> >>>> You mean the comment? I can add it of course like for regulators. >>>> >>> >>> I mean in place of the function-enumerator... that's practically used to >>> distinguish between instances, it's not too common to see it, and usually >>> "label" replaces exactly that - just that, instead of a different number, >>> it gets a different name with no (usually) meaningless numbers :-) >> >> as far as i understand using label also makes "function" property useless, after discussing >> this with eric i would drop both on all 4 places by labels like these: >> >> label = "yellow-lan"; >> label = "green-lan"; >> ... >> >> not sure if we should drop color property too... >> > >I'm looking at the leds binding (leds/common.yaml) right now. > >My suggestion of using 'label' was actually wrong - and your devicetree was >actually right!!! (apart from the default-trigger that may not work) > >Infact, the documentation says, in brief: > >- function-enumerator is ignored if label is present >- function doesn't say that gets ignored >- color doesn't say that gets ignored >- label says: > - If not present -> get string from node name > - function-enumerator ignored > - This property is deprecated > >...but the 'label' binding does not say 'deprecated: true', which is something >that must be fixed! Ok,i can try to add the property to binding (independ of this series). Imho label was cleaner than function and function-enumerator... >So, I'm sorry for the confusion, the noise and the useless loss of time around >this - you can keep the LED nodes as they are, and that's a lesson for the future >me reviewing another node like this one. Don't worry, we are all humas...i missed looking in linux-next for the other binding-patches. >P.S.: This shouldn't have been a RFC, as the patches are more than RFC quality!!! I sent it as RFC because i had not expected to be merged before next is closed. >Cheers, >Angelo > >>>>>> + default-state = "keep"; >>>>>> + linux,default-trigger = "netdev"; >>>>>> + }; >>>>>> + led@1 { /* en8811_a_gpio4 */ >>>>>> + reg = <1>; >>>>>> + color = <LED_COLOR_ID_GREEN>; >>>>>> + function = LED_FUNCTION_LAN; >>>>>> + function-enumerator = <2>; >>>>>> + default-state = "keep"; >>>>>> + linux,default-trigger = "netdev"; >>>>>> + }; >>>>>> + }; >>>>>> + }; >>>>>> + >>>>>> + phy15: ethernet-phy@15 { >>>>>> + reg = <15>; regards Frank
Il 09/05/24 12:30, Frank Wunderlich ha scritto: > Am 9. Mai 2024 12:10:59 MESZ schrieb AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>: >> Il 08/05/24 20:25, Frank Wunderlich ha scritto: >>> Hi >>> >>>> Gesendet: Dienstag, 07. Mai 2024 um 15:35 Uhr >>>> Von: "AngeloGioacchino Del Regno" <angelogioacchino.delregno@collabora.com> >>>> >>>> Il 06/05/24 18:00, Frank Wunderlich ha scritto: >>> >>>>>>> + fan: pwm-fan { >>>>>>> + compatible = "pwm-fan"; >>>>>>> + #cooling-cells = <2>; >>>>>>> + /* cooling level (0, 1, 2) - pwm inverted */ >>>>>>> + cooling-levels = <255 96 0>; >>>>>> >>>>>> Did you try to actually invert the PWM? >>>>>> >>>>>> Look for PWM_POLARITY_INVERTED ;-) >>>>> >>>>> Mtk pwm driver does not support it >>>>> >>>>> https://elixir.bootlin.com/linux/latest/source/drivers/pwm/pwm-mediatek.c#L211 >>>>> >>>> >>>> You're right, sorry - I confused the general purpose PWM controller with the >>>> rather specific DISP_PWM controller (which does support polarity inversion). >>>> >>>> It's good - but I'd appreciate if you can please add a comment stating that >>>> the PWM values are inverted in SW because the controller does *not* support >>>> polarity inversion... so that next time someone looks at this will immediately >>>> understand what's going on and why :-) >>> >>> so i would change comment like this: >>> >>> /* cooling level (0, 1, 2) >>> * signal is inverted on board >>> * mtk pwm driver does not support >>> * PWM_POLARITY_INVERTED */ >>> >> >> There you go: >> >> /* >> * The signal is inverted on this board and the general purpose >> * PWM HW IP in this SoC does not support polarity inversion. >> */ >> /* Cooling level < 0 1 2> */ >> cooling-levels = <255 96 0>; > > Thanks for clearing structure of the comment,but imho actually it is a driver issue (for all mtk SoC). Not sure it is really a hardware limitation. So i would change this to "... and the PWM driver does not support polarity inversion." > >>>>>>> + pwms = <&pwm 0 10000>; >>>>>>> + status = "okay"; >>>>>>> + }; >>>>>>> + >>>>>>> + phy14: ethernet-phy@14 { >>> ... >>>>>>> + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; >>>>>>> + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; >>>>>>> + reset-assert-us = <10000>; >>>>>>> + reset-deassert-us = <20000>; >>>>>>> + phy-mode = "2500base-x"; >>>>>>> + full-duplex; >>>>>>> + pause; >>>>>>> + airoha,pnswap-rx; >>>>>>> + >>>>>>> + leds { >>>>>>> + #address-cells = <1>; >>>>>>> + #size-cells = <0>; >>>>>>> + >>>>>>> + led@0 { /* en8811_a_gpio5 */ >>>>>>> + reg = <0>; >>>>>>> + color = <LED_COLOR_ID_YELLOW>; >>>>>>> + function = LED_FUNCTION_LAN; >>>>>>> + function-enumerator = <1>; >>>>>> >>>>>> Why aren't you simply using a label? >>>>> >>>>> You mean the comment? I can add it of course like for regulators. >>>>> >>>> >>>> I mean in place of the function-enumerator... that's practically used to >>>> distinguish between instances, it's not too common to see it, and usually >>>> "label" replaces exactly that - just that, instead of a different number, >>>> it gets a different name with no (usually) meaningless numbers :-) >>> >>> as far as i understand using label also makes "function" property useless, after discussing >>> this with eric i would drop both on all 4 places by labels like these: >>> >>> label = "yellow-lan"; >>> label = "green-lan"; >>> ... >>> >>> not sure if we should drop color property too... >>> >> >> I'm looking at the leds binding (leds/common.yaml) right now. >> >> My suggestion of using 'label' was actually wrong - and your devicetree was >> actually right!!! (apart from the default-trigger that may not work) >> >> Infact, the documentation says, in brief: >> >> - function-enumerator is ignored if label is present >> - function doesn't say that gets ignored >> - color doesn't say that gets ignored >> - label says: >> - If not present -> get string from node name >> - function-enumerator ignored >> - This property is deprecated >> >> ...but the 'label' binding does not say 'deprecated: true', which is something >> that must be fixed! > > Ok,i can try to add the property to binding (independ of this series). Imho label was cleaner than function and function-enumerator... > Oh I sort of agree with you, I liked the label more, as it's more consistent with everything else... but oh well. :-) >> So, I'm sorry for the confusion, the noise and the useless loss of time around >> this - you can keep the LED nodes as they are, and that's a lesson for the future >> me reviewing another node like this one. > > Don't worry, we are all humas...i missed looking in linux-next for the other binding-patches. > >> P.S.: This shouldn't have been a RFC, as the patches are more than RFC quality!!! > > I sent it as RFC because i had not expected to be merged before next is closed. > Ah at least from my side, no worries... when I see RFC I generally expect to see "dubious/head-scratching stuff", not "sub-optimal timing to send a patch" :-P Cheers! Angelo >> >>>>>>> + default-state = "keep"; >>>>>>> + linux,default-trigger = "netdev"; >>>>>>> + }; >>>>>>> + led@1 { /* en8811_a_gpio4 */ >>>>>>> + reg = <1>; >>>>>>> + color = <LED_COLOR_ID_GREEN>; >>>>>>> + function = LED_FUNCTION_LAN; >>>>>>> + function-enumerator = <2>; >>>>>>> + default-state = "keep"; >>>>>>> + linux,default-trigger = "netdev"; >>>>>>> + }; >>>>>>> + }; >>>>>>> + }; >>>>>>> + >>>>>>> + phy15: ethernet-phy@15 { >>>>>>> + reg = <15>; > > > regards Frank
diff --git a/arch/arm64/boot/dts/mediatek/Makefile b/arch/arm64/boot/dts/mediatek/Makefile index 37b4ca3a87c9..1763b001ab06 100644 --- a/arch/arm64/boot/dts/mediatek/Makefile +++ b/arch/arm64/boot/dts/mediatek/Makefile @@ -11,6 +11,7 @@ dtb-$(CONFIG_ARCH_MEDIATEK) += mt7622-bananapi-bpi-r64.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7981b-xiaomi-ax3000t.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-acelink-ew-7886cax.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3.dtb +dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-mini.dtb dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-emmc.dtbo dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nand.dtbo dtb-$(CONFIG_ARCH_MEDIATEK) += mt7986a-bananapi-bpi-r3-nor.dtbo diff --git a/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts new file mode 100644 index 000000000000..c764b4dc4752 --- /dev/null +++ b/arch/arm64/boot/dts/mediatek/mt7986a-bananapi-bpi-r3-mini.dts @@ -0,0 +1,486 @@ +// SPDX-License-Identifier: (GPL-2.0 OR MIT) +/* + * Copyright (C) 2021 MediaTek Inc. + * Authors: Frank Wunderlich <frank-w@public-files.de> + * Eric Woudstra <ericwouds@gmail.com> + * Tianling Shen <cnsztl@immortalwrt.org> + */ + +/dts-v1/; + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/input/input.h> +#include <dt-bindings/leds/common.h> +#include <dt-bindings/pinctrl/mt65xx.h> + +#include "mt7986a.dtsi" + +/ { + model = "Bananapi BPI-R3 Mini"; + chassis-type = "embedded"; + compatible = "bananapi,bpi-r3mini", "mediatek,mt7986a"; + + aliases { + serial0 = &uart0; + ethernet0 = &gmac0; + ethernet1 = &gmac1; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + dcin: regulator-12vd { + compatible = "regulator-fixed"; + regulator-name = "12vd"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + regulator-boot-on; + regulator-always-on; + }; + + fan: pwm-fan { + compatible = "pwm-fan"; + #cooling-cells = <2>; + /* cooling level (0, 1, 2) - pwm inverted */ + cooling-levels = <255 96 0>; + pwms = <&pwm 0 10000>; + status = "okay"; + }; + + reg_1p8v: regulator-1p8v { + compatible = "regulator-fixed"; + regulator-name = "1.8vd"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <&dcin>; + }; + + reg_3p3v: regulator-3p3v { + compatible = "regulator-fixed"; + regulator-name = "3.3vd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-boot-on; + regulator-always-on; + vin-supply = <&dcin>; + }; + + usb_vbus: regulator-usb-vbus { + compatible = "regulator-fixed"; + regulator-name = "usb_vbus"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpios = <&pio 20 GPIO_ACTIVE_LOW>; + regulator-boot-on; + }; + + en8811_a: regulator-phy1 { + compatible = "regulator-fixed"; + regulator-name = "phy1"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 16 GPIO_ACTIVE_LOW>; + regulator-always-on; + }; + + en8811_b: regulator-phy2 { + compatible = "regulator-fixed"; + regulator-name = "phy2"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + gpio = <&pio 17 GPIO_ACTIVE_LOW>; + regulator-always-on; + }; + + leds { + compatible = "gpio-leds"; + + green_led: led-0 { + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_POWER; + gpios = <&pio 19 GPIO_ACTIVE_HIGH>; + default-state = "on"; + }; + }; + + gpio-keys { + compatible = "gpio-keys"; + + reset-key { + label = "reset"; + linux,code = <KEY_RESTART>; + gpios = <&pio 7 GPIO_ACTIVE_LOW>; + }; + }; + +}; + +&cpu_thermal { + cooling-maps { + map0 { + /* active: set fan to cooling level 2 */ + cooling-device = <&fan 2 2>; + trip = <&cpu_trip_active_high>; + }; + + map1 { + /* active: set fan to cooling level 1 */ + cooling-device = <&fan 1 1>; + trip = <&cpu_trip_active_med>; + }; + + map2 { + /* active: set fan to cooling level 0 */ + cooling-device = <&fan 0 0>; + trip = <&cpu_trip_active_low>; + }; + }; +}; + +&crypto { + status = "okay"; +}; + +ð { + status = "okay"; + + gmac0: mac@0 { + compatible = "mediatek,eth-mac"; + reg = <0>; + phy-mode = "2500base-x"; + phy-handle = <&phy14>; + }; + + gmac1: mac@1 { + compatible = "mediatek,eth-mac"; + reg = <1>; + phy-mode = "2500base-x"; + phy-handle = <&phy15>; + }; + + mdio: mdio-bus { + #address-cells = <1>; + #size-cells = <0>; + }; +}; + +&mmc0 { + pinctrl-names = "default", "state_uhs"; + pinctrl-0 = <&mmc0_pins_default>; + pinctrl-1 = <&mmc0_pins_uhs>; + vmmc-supply = <®_3p3v>; + vqmmc-supply = <®_1p8v>; +}; + + +&i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&i2c_pins>; + status = "okay"; + + /* MAC Address EEPROM */ + eeprom@50 { + compatible = "atmel,24c02"; + reg = <0x50>; + + address-width = <8>; + pagesize = <8>; + size = <256>; + }; +}; + +&mdio { + #address-cells = <1>; + #size-cells = <0>; + + phy14: ethernet-phy@14 { + reg = <14>; + interrupts-extended = <&pio 48 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&pio 49 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <20000>; + phy-mode = "2500base-x"; + full-duplex; + pause; + airoha,pnswap-rx; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@0 { /* en8811_a_gpio5 */ + reg = <0>; + color = <LED_COLOR_ID_YELLOW>; + function = LED_FUNCTION_LAN; + function-enumerator = <1>; + default-state = "keep"; + linux,default-trigger = "netdev"; + }; + led@1 { /* en8811_a_gpio4 */ + reg = <1>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_LAN; + function-enumerator = <2>; + default-state = "keep"; + linux,default-trigger = "netdev"; + }; + }; + }; + + phy15: ethernet-phy@15 { + reg = <15>; + interrupts-extended = <&pio 46 IRQ_TYPE_EDGE_FALLING>; + reset-gpios = <&pio 47 GPIO_ACTIVE_LOW>; + reset-assert-us = <10000>; + reset-deassert-us = <20000>; + phy-mode = "2500base-x"; + full-duplex; + pause; + airoha,pnswap-rx; + + leds { + #address-cells = <1>; + #size-cells = <0>; + + led@0 { /* en8811_b_gpio5 */ + reg = <0>; + color = <LED_COLOR_ID_YELLOW>; + function = LED_FUNCTION_WAN; + function-enumerator = <1>; + default-state = "keep"; + linux,default-trigger = "netdev"; + }; + led@1 { /* en8811_b_gpio4 */ + reg = <1>; + color = <LED_COLOR_ID_GREEN>; + function = LED_FUNCTION_WAN; + function-enumerator = <2>; + default-state = "keep"; + linux,default-trigger = "netdev"; + }; + }; + }; +}; + +&pcie { + pinctrl-names = "default"; + pinctrl-0 = <&pcie_pins>; + status = "okay"; +}; + +&pcie_phy { + status = "okay"; +}; + +&pio { + i2c_pins: i2c-pins { + mux { + function = "i2c"; + groups = "i2c"; + }; + }; + + mmc0_pins_default: mmc0-pins { + mux { + function = "emmc"; + groups = "emmc_51"; + }; + conf-cmd-dat { + pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", + "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", + "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; + input-enable; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + conf-clk { + pins = "EMMC_CK"; + drive-strength = <6>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-ds { + pins = "EMMC_DSL"; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-rst { + pins = "EMMC_RSTB"; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + }; + + mmc0_pins_uhs: mmc0-uhs-pins { + mux { + function = "emmc"; + groups = "emmc_51"; + }; + conf-cmd-dat { + pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", + "EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", + "EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; + input-enable; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + conf-clk { + pins = "EMMC_CK"; + drive-strength = <6>; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-ds { + pins = "EMMC_DSL"; + bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ + }; + conf-rst { + pins = "EMMC_RSTB"; + drive-strength = <4>; + bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ + }; + }; + + pcie_pins: pcie-pins { + mux { + function = "pcie"; + groups = "pcie_clk", "pcie_wake", "pcie_pereset"; + }; + }; + + pwm_pins: pwm-pins { + mux { + function = "pwm"; + groups = "pwm0"; + }; + }; + + spi_flash_pins: spi-flash-pins { + mux { + function = "spi"; + groups = "spi0", "spi0_wp_hold"; + }; + }; + + usb_ngff_pins: usb-ngff-pins { + ngff-gnss-off-conf { + pins = "GPIO_6"; + drive-strength = <8>; + mediatek,pull-up-adv = <1>; + }; + ngff-pe-rst-conf { + pins = "GPIO_7"; + drive-strength = <8>; + mediatek,pull-up-adv = <1>; + }; + ngff-wwan-off-conf { + pins = "GPIO_8"; + drive-strength = <8>; + mediatek,pull-up-adv = <1>; + }; + ngff-pwr-off-conf { + pins = "GPIO_9"; + drive-strength = <8>; + mediatek,pull-up-adv = <1>; + }; + ngff-rst-conf { + pins = "GPIO_10"; + drive-strength = <8>; + mediatek,pull-up-adv = <1>; + }; + ngff-coex-conf { + pins = "SPI1_CS"; + drive-strength = <8>; + mediatek,pull-up-adv = <1>; + }; + }; + + wf_2g_5g_pins: wf-2g-5g-pins { + mux { + function = "wifi"; + groups = "wf_2g", "wf_5g"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + wf_dbdc_pins: wf-dbdc-pins { + mux { + function = "wifi"; + groups = "wf_dbdc"; + }; + conf { + pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", + "WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", + "WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", + "WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", + "WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", + "WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", + "WF1_TOP_CLK", "WF1_TOP_DATA"; + drive-strength = <4>; + }; + }; + + wf_led_pins: wf-led-pins { + mux { + function = "led"; + groups = "wifi_led"; + }; + }; +}; + +&pwm { + pinctrl-names = "default"; + pinctrl-0 = <&pwm_pins>; + status = "okay"; +}; + +&spi0 { + pinctrl-names = "default"; + pinctrl-0 = <&spi_flash_pins>; + status = "okay"; +}; + +&ssusb { + pinctrl-names = "default"; + pinctrl-0 = <&usb_ngff_pins>; + vusb33-supply = <®_3p3v>; + vbus-supply = <&usb_vbus>; + status = "okay"; +}; + +&trng { + status = "okay"; +}; + +&uart0 { + status = "okay"; +}; + +&usb_phy { + status = "okay"; +}; + +&watchdog { + status = "okay"; +}; + +&wifi { + status = "okay"; + pinctrl-names = "default", "dbdc"; + pinctrl-0 = <&wf_2g_5g_pins>, <&wf_led_pins>; + pinctrl-1 = <&wf_dbdc_pins>, <&wf_led_pins>; + + led { + led-active-low; + }; +}; +