@@ -56,187 +56,6 @@ int ksz9477_change_mtu(struct ksz_device *dev, int port, int mtu)
REG_SW_MTU_MASK, frame_size);
}
-/**
- * ksz9477_handle_wake_reason - Handle wake reason on a specified port.
- * @dev: The device structure.
- * @port: The port number.
- *
- * This function reads the PME (Power Management Event) status register of a
- * specified port to determine the wake reason. If there is no wake event, it
- * returns early. Otherwise, it logs the wake reason which could be due to a
- * "Magic Packet", "Link Up", or "Energy Detect" event. The PME status register
- * is then cleared to acknowledge the handling of the wake event.
- *
- * Return: 0 on success, or an error code on failure.
- */
-static int ksz9477_handle_wake_reason(struct ksz_device *dev, int port)
-{
- u8 pme_status;
- int ret;
-
- ret = ksz_pread8(dev, port, REG_PORT_PME_STATUS, &pme_status);
- if (ret)
- return ret;
-
- if (!pme_status)
- return 0;
-
- dev_dbg(dev->dev, "Wake event on port %d due to:%s%s%s\n", port,
- pme_status & PME_WOL_MAGICPKT ? " \"Magic Packet\"" : "",
- pme_status & PME_WOL_LINKUP ? " \"Link Up\"" : "",
- pme_status & PME_WOL_ENERGY ? " \"Energy detect\"" : "");
-
- return ksz_pwrite8(dev, port, REG_PORT_PME_STATUS, pme_status);
-}
-
-/**
- * ksz9477_get_wol - Get Wake-on-LAN settings for a specified port.
- * @dev: The device structure.
- * @port: The port number.
- * @wol: Pointer to ethtool Wake-on-LAN settings structure.
- *
- * This function checks the PME Pin Control Register to see if PME Pin Output
- * Enable is set, indicating PME is enabled. If enabled, it sets the supported
- * and active WoL flags.
- */
-void ksz9477_get_wol(struct ksz_device *dev, int port,
- struct ethtool_wolinfo *wol)
-{
- u8 pme_ctrl;
- int ret;
-
- if (!dev->wakeup_source)
- return;
-
- wol->supported = WAKE_PHY;
-
- /* Check if the current MAC address on this port can be set
- * as global for WAKE_MAGIC support. The result may vary
- * dynamically based on other ports configurations.
- */
- if (ksz_is_port_mac_global_usable(dev->ds, port))
- wol->supported |= WAKE_MAGIC;
-
- ret = ksz_pread8(dev, port, REG_PORT_PME_CTRL, &pme_ctrl);
- if (ret)
- return;
-
- if (pme_ctrl & PME_WOL_MAGICPKT)
- wol->wolopts |= WAKE_MAGIC;
- if (pme_ctrl & (PME_WOL_LINKUP | PME_WOL_ENERGY))
- wol->wolopts |= WAKE_PHY;
-}
-
-/**
- * ksz9477_set_wol - Set Wake-on-LAN settings for a specified port.
- * @dev: The device structure.
- * @port: The port number.
- * @wol: Pointer to ethtool Wake-on-LAN settings structure.
- *
- * This function configures Wake-on-LAN (WoL) settings for a specified port.
- * It validates the provided WoL options, checks if PME is enabled via the
- * switch's PME Pin Control Register, clears any previous wake reasons,
- * and sets the Magic Packet flag in the port's PME control register if
- * specified.
- *
- * Return: 0 on success, or other error codes on failure.
- */
-int ksz9477_set_wol(struct ksz_device *dev, int port,
- struct ethtool_wolinfo *wol)
-{
- u8 pme_ctrl = 0, pme_ctrl_old = 0;
- bool magic_switched_off;
- bool magic_switched_on;
- int ret;
-
- if (wol->wolopts & ~(WAKE_PHY | WAKE_MAGIC))
- return -EINVAL;
-
- if (!dev->wakeup_source)
- return -EOPNOTSUPP;
-
- ret = ksz9477_handle_wake_reason(dev, port);
- if (ret)
- return ret;
-
- if (wol->wolopts & WAKE_MAGIC)
- pme_ctrl |= PME_WOL_MAGICPKT;
- if (wol->wolopts & WAKE_PHY)
- pme_ctrl |= PME_WOL_LINKUP | PME_WOL_ENERGY;
-
- ret = ksz_pread8(dev, port, REG_PORT_PME_CTRL, &pme_ctrl_old);
- if (ret)
- return ret;
-
- if (pme_ctrl_old == pme_ctrl)
- return 0;
-
- magic_switched_off = (pme_ctrl_old & PME_WOL_MAGICPKT) &&
- !(pme_ctrl & PME_WOL_MAGICPKT);
- magic_switched_on = !(pme_ctrl_old & PME_WOL_MAGICPKT) &&
- (pme_ctrl & PME_WOL_MAGICPKT);
-
- /* To keep reference count of MAC address, we should do this
- * operation only on change of WOL settings.
- */
- if (magic_switched_on) {
- ret = ksz_switch_macaddr_get(dev->ds, port, NULL);
- if (ret)
- return ret;
- } else if (magic_switched_off) {
- ksz_switch_macaddr_put(dev->ds);
- }
-
- ret = ksz_pwrite8(dev, port, REG_PORT_PME_CTRL, pme_ctrl);
- if (ret) {
- if (magic_switched_on)
- ksz_switch_macaddr_put(dev->ds);
- return ret;
- }
-
- return 0;
-}
-
-/**
- * ksz9477_wol_pre_shutdown - Prepares the switch device for shutdown while
- * considering Wake-on-LAN (WoL) settings.
- * @dev: The switch device structure.
- * @wol_enabled: Pointer to a boolean which will be set to true if WoL is
- * enabled on any port.
- *
- * This function prepares the switch device for a safe shutdown while taking
- * into account the Wake-on-LAN (WoL) settings on the user ports. It updates
- * the wol_enabled flag accordingly to reflect whether WoL is active on any
- * port.
- */
-void ksz9477_wol_pre_shutdown(struct ksz_device *dev, bool *wol_enabled)
-{
- struct dsa_port *dp;
- int ret;
-
- *wol_enabled = false;
-
- if (!dev->wakeup_source)
- return;
-
- dsa_switch_for_each_user_port(dp, dev->ds) {
- u8 pme_ctrl = 0;
-
- ret = ksz_pread8(dev, dp->index, REG_PORT_PME_CTRL, &pme_ctrl);
- if (!ret && pme_ctrl)
- *wol_enabled = true;
-
- /* make sure there are no pending wake events which would
- * prevent the device from going to sleep/shutdown.
- */
- ksz9477_handle_wake_reason(dev, dp->index);
- }
-
- /* Now we are save to enable PME pin. */
- if (*wol_enabled)
- ksz_write8(dev, REG_SW_PME_CTRL, PME_ENABLE);
-}
-
static int ksz9477_wait_vlan_ctrl_ready(struct ksz_device *dev)
{
unsigned int val;
@@ -3740,6 +3740,44 @@ static void ksz_get_wol(struct dsa_switch *ds, int port,
dev->dev_ops->get_wol(dev, port, wol);
}
+/**
+ * ksz9477_get_wol - Get Wake-on-LAN settings for a specified port.
+ * @dev: The device structure.
+ * @port: The port number.
+ * @wol: Pointer to ethtool Wake-on-LAN settings structure.
+ *
+ * This function checks the PME Pin Control Register to see if PME Pin Output
+ * Enable is set, indicating PME is enabled. If enabled, it sets the supported
+ * and active WoL flags.
+ */
+void ksz9477_get_wol(struct ksz_device *dev, int port,
+ struct ethtool_wolinfo *wol)
+{
+ u8 pme_ctrl;
+ int ret;
+
+ if (!dev->wakeup_source)
+ return;
+
+ wol->supported = WAKE_PHY;
+
+ /* Check if the current MAC address on this port can be set
+ * as global for WAKE_MAGIC support. The result may vary
+ * dynamically based on other ports configurations.
+ */
+ if (ksz_is_port_mac_global_usable(dev->ds, port))
+ wol->supported |= WAKE_MAGIC;
+
+ ret = ksz_pread8(dev, port, REG_PORT_PME_CTRL, &pme_ctrl);
+ if (ret)
+ return;
+
+ if (pme_ctrl & PME_WOL_MAGICPKT)
+ wol->wolopts |= WAKE_MAGIC;
+ if (pme_ctrl & (PME_WOL_LINKUP | PME_WOL_ENERGY))
+ wol->wolopts |= WAKE_PHY;
+}
+
static int ksz_set_wol(struct dsa_switch *ds, int port,
struct ethtool_wolinfo *wol)
{
@@ -3751,6 +3789,149 @@ static int ksz_set_wol(struct dsa_switch *ds, int port,
return -EOPNOTSUPP;
}
+/**
+ * ksz9477_set_wol - Set Wake-on-LAN settings for a specified port.
+ * @dev: The device structure.
+ * @port: The port number.
+ * @wol: Pointer to ethtool Wake-on-LAN settings structure.
+ *
+ * This function configures Wake-on-LAN (WoL) settings for a specified port.
+ * It validates the provided WoL options, checks if PME is enabled via the
+ * switch's PME Pin Control Register, clears any previous wake reasons,
+ * and sets the Magic Packet flag in the port's PME control register if
+ * specified.
+ *
+ * Return: 0 on success, or other error codes on failure.
+ */
+int ksz9477_set_wol(struct ksz_device *dev, int port,
+ struct ethtool_wolinfo *wol)
+{
+ u8 pme_ctrl = 0, pme_ctrl_old = 0;
+ bool magic_switched_off;
+ bool magic_switched_on;
+ int ret;
+
+ if (wol->wolopts & ~(WAKE_PHY | WAKE_MAGIC))
+ return -EINVAL;
+
+ if (!dev->wakeup_source)
+ return -EOPNOTSUPP;
+
+ ret = ksz9477_handle_wake_reason(dev, port);
+ if (ret)
+ return ret;
+
+ if (wol->wolopts & WAKE_MAGIC)
+ pme_ctrl |= PME_WOL_MAGICPKT;
+ if (wol->wolopts & WAKE_PHY)
+ pme_ctrl |= PME_WOL_LINKUP | PME_WOL_ENERGY;
+
+ ret = ksz_pread8(dev, port, REG_PORT_PME_CTRL, &pme_ctrl_old);
+ if (ret)
+ return ret;
+
+ if (pme_ctrl_old == pme_ctrl)
+ return 0;
+
+ magic_switched_off = (pme_ctrl_old & PME_WOL_MAGICPKT) &&
+ !(pme_ctrl & PME_WOL_MAGICPKT);
+ magic_switched_on = !(pme_ctrl_old & PME_WOL_MAGICPKT) &&
+ (pme_ctrl & PME_WOL_MAGICPKT);
+
+ /* To keep reference count of MAC address, we should do this
+ * operation only on change of WOL settings.
+ */
+ if (magic_switched_on) {
+ ret = ksz_switch_macaddr_get(dev->ds, port, NULL);
+ if (ret)
+ return ret;
+ } else if (magic_switched_off) {
+ ksz_switch_macaddr_put(dev->ds);
+ }
+
+ ret = ksz_pwrite8(dev, port, REG_PORT_PME_CTRL, pme_ctrl);
+ if (ret) {
+ if (magic_switched_on)
+ ksz_switch_macaddr_put(dev->ds);
+ return ret;
+ }
+
+ return 0;
+}
+
+/**
+ * ksz9477_handle_wake_reason - Handle wake reason on a specified port.
+ * @dev: The device structure.
+ * @port: The port number.
+ *
+ * This function reads the PME (Power Management Event) status register of a
+ * specified port to determine the wake reason. If there is no wake event, it
+ * returns early. Otherwise, it logs the wake reason which could be due to a
+ * "Magic Packet", "Link Up", or "Energy Detect" event. The PME status register
+ * is then cleared to acknowledge the handling of the wake event.
+ *
+ * Return: 0 on success, or an error code on failure.
+ */
+static int ksz9477_handle_wake_reason(struct ksz_device *dev, int port)
+{
+ u8 pme_status;
+ int ret;
+
+ ret = ksz_pread8(dev, port, REG_PORT_PME_STATUS, &pme_status);
+ if (ret)
+ return ret;
+
+ if (!pme_status)
+ return 0;
+
+ dev_dbg(dev->dev, "Wake event on port %d due to:%s%s%s\n", port,
+ pme_status & PME_WOL_MAGICPKT ? " \"Magic Packet\"" : "",
+ pme_status & PME_WOL_LINKUP ? " \"Link Up\"" : "",
+ pme_status & PME_WOL_ENERGY ? " \"Energy detect\"" : "");
+
+ return ksz_pwrite8(dev, port, REG_PORT_PME_STATUS, pme_status);
+}
+
+/**
+ * ksz9477_wol_pre_shutdown - Prepares the switch device for shutdown while
+ * considering Wake-on-LAN (WoL) settings.
+ * @dev: The switch device structure.
+ * @wol_enabled: Pointer to a boolean which will be set to true if WoL is
+ * enabled on any port.
+ *
+ * This function prepares the switch device for a safe shutdown while taking
+ * into account the Wake-on-LAN (WoL) settings on the user ports. It updates
+ * the wol_enabled flag accordingly to reflect whether WoL is active on any
+ * port.
+ */
+void ksz9477_wol_pre_shutdown(struct ksz_device *dev, bool *wol_enabled)
+{
+ struct dsa_port *dp;
+ int ret;
+
+ *wol_enabled = false;
+
+ if (!dev->wakeup_source)
+ return;
+
+ dsa_switch_for_each_user_port(dp, dev->ds) {
+ u8 pme_ctrl = 0;
+
+ ret = ksz_pread8(dev, dp->index, REG_PORT_PME_CTRL, &pme_ctrl);
+ if (!ret && pme_ctrl)
+ *wol_enabled = true;
+
+ /* make sure there are no pending wake events which would
+ * prevent the device from going to sleep/shutdown.
+ */
+ ksz9477_handle_wake_reason(dev, dp->index);
+ }
+
+ /* Now we are save to enable PME pin. */
+ if (*wol_enabled)
+ ksz_write8(dev, REG_SW_PME_CTRL, PME_ENABLE);
+}
+
static int ksz_port_set_mac_address(struct dsa_switch *ds, int port,
const unsigned char *addr)
{