@@ -46,12 +46,13 @@ config LAN743X
tristate "LAN743x support"
depends on PCI
depends on PTP_1588_CLOCK_OPTIONAL
- select PHYLIB
select FIXED_PHY
select CRC16
select CRC32
+ select PHYLINK
help
- Support for the Microchip LAN743x PCI Express Gigabit Ethernet chip
+ Support for the Microchip LAN743x and PCI11x1x families of PCI
+ Express Ethernet devices
To compile this driver as a module, choose M here. The module will be
called lan743x.
@@ -15,6 +15,7 @@
#include <linux/rtnetlink.h>
#include <linux/iopoll.h>
#include <linux/crc16.h>
+#include <linux/phylink.h>
#include "lan743x_main.h"
#include "lan743x_ethtool.h"
@@ -1077,26 +1078,7 @@ static int lan743x_sgmii_2_5G_mode_set(struct lan743x_adapter *adapter,
VR_MII_BAUD_RATE_1P25GBPS);
}
-static int lan743x_is_sgmii_2_5G_mode(struct lan743x_adapter *adapter,
- bool *status)
-{
- int ret;
-
- ret = lan743x_sgmii_read(adapter, MDIO_MMD_VEND2,
- VR_MII_GEN2_4_MPLL_CTRL1);
- if (ret < 0)
- return ret;
-
- if (ret == VR_MII_MPLL_MULTIPLIER_125 ||
- ret == VR_MII_MPLL_MULTIPLIER_50)
- *status = true;
- else
- *status = false;
-
- return 0;
-}
-
-static int lan743x_sgmii_aneg_update(struct lan743x_adapter *adapter)
+static int lan743x_serdes_clock_and_aneg_update(struct lan743x_adapter *adapter)
{
enum lan743x_sgmii_lsd lsd = adapter->sgmii_lsd;
int mii_ctrl;
@@ -1211,49 +1193,6 @@ static int lan743x_pcs_power_reset(struct lan743x_adapter *adapter)
return lan743x_pcs_seq_state(adapter, PCS_POWER_STATE_UP);
}
-static int lan743x_sgmii_config(struct lan743x_adapter *adapter)
-{
- struct net_device *netdev = adapter->netdev;
- struct phy_device *phydev = netdev->phydev;
- bool status;
- int ret;
-
- ret = lan743x_get_lsd(phydev->speed, phydev->duplex,
- phydev->master_slave_state);
- if (ret < 0) {
- netif_err(adapter, drv, adapter->netdev,
- "error %d link-speed-duplex(LSD) invalid\n", ret);
- return ret;
- }
-
- adapter->sgmii_lsd = ret;
- netif_dbg(adapter, drv, adapter->netdev,
- "Link Speed Duplex (lsd) : 0x%X\n", adapter->sgmii_lsd);
-
- ret = lan743x_sgmii_aneg_update(adapter);
- if (ret < 0) {
- netif_err(adapter, drv, adapter->netdev,
- "error %d SGMII cfg failed\n", ret);
- return ret;
- }
-
- ret = lan743x_is_sgmii_2_5G_mode(adapter, &status);
- if (ret < 0) {
- netif_err(adapter, drv, adapter->netdev,
- "error %d SGMII get mode failed\n", ret);
- return ret;
- }
-
- if (status)
- netif_dbg(adapter, drv, adapter->netdev,
- "SGMII 2.5G mode enable\n");
- else
- netif_dbg(adapter, drv, adapter->netdev,
- "SGMII 1G mode enable\n");
-
- return lan743x_pcs_power_reset(adapter);
-}
-
static void lan743x_mac_set_address(struct lan743x_adapter *adapter,
u8 *addr)
{
@@ -1407,103 +1346,11 @@ static int lan743x_phy_reset(struct lan743x_adapter *adapter)
50000, 1000000);
}
-static void lan743x_phy_update_flowcontrol(struct lan743x_adapter *adapter,
- u16 local_adv, u16 remote_adv)
-{
- struct lan743x_phy *phy = &adapter->phy;
- u8 cap;
-
- if (phy->fc_autoneg)
- cap = mii_resolve_flowctrl_fdx(local_adv, remote_adv);
- else
- cap = phy->fc_request_control;
-
- lan743x_mac_flow_ctrl_set_enables(adapter,
- cap & FLOW_CTRL_TX,
- cap & FLOW_CTRL_RX);
-}
-
static int lan743x_phy_init(struct lan743x_adapter *adapter)
{
return lan743x_phy_reset(adapter);
}
-static void lan743x_phy_link_status_change(struct net_device *netdev)
-{
- struct lan743x_adapter *adapter = netdev_priv(netdev);
- struct phy_device *phydev = netdev->phydev;
- u32 data;
-
- phy_print_status(phydev);
- if (phydev->state == PHY_RUNNING) {
- int remote_advertisement = 0;
- int local_advertisement = 0;
-
- data = lan743x_csr_read(adapter, MAC_CR);
-
- /* set duplex mode */
- if (phydev->duplex)
- data |= MAC_CR_DPX_;
- else
- data &= ~MAC_CR_DPX_;
-
- /* set bus speed */
- switch (phydev->speed) {
- case SPEED_10:
- data &= ~MAC_CR_CFG_H_;
- data &= ~MAC_CR_CFG_L_;
- break;
- case SPEED_100:
- data &= ~MAC_CR_CFG_H_;
- data |= MAC_CR_CFG_L_;
- break;
- case SPEED_1000:
- data |= MAC_CR_CFG_H_;
- data &= ~MAC_CR_CFG_L_;
- break;
- case SPEED_2500:
- data |= MAC_CR_CFG_H_;
- data |= MAC_CR_CFG_L_;
- break;
- }
- lan743x_csr_write(adapter, MAC_CR, data);
-
- local_advertisement =
- linkmode_adv_to_mii_adv_t(phydev->advertising);
- remote_advertisement =
- linkmode_adv_to_mii_adv_t(phydev->lp_advertising);
-
- lan743x_phy_update_flowcontrol(adapter, local_advertisement,
- remote_advertisement);
- lan743x_ptp_update_latency(adapter, phydev->speed);
- if (phydev->interface == PHY_INTERFACE_MODE_SGMII ||
- phydev->interface == PHY_INTERFACE_MODE_1000BASEX ||
- phydev->interface == PHY_INTERFACE_MODE_2500BASEX)
- lan743x_sgmii_config(adapter);
-
- data = lan743x_csr_read(adapter, MAC_CR);
- if (phydev->enable_tx_lpi)
- data |= MAC_CR_EEE_EN_;
- else
- data &= ~MAC_CR_EEE_EN_;
- lan743x_csr_write(adapter, MAC_CR, data);
- }
-}
-
-static void lan743x_phy_close(struct lan743x_adapter *adapter)
-{
- struct net_device *netdev = adapter->netdev;
- struct phy_device *phydev = netdev->phydev;
-
- phy_stop(netdev->phydev);
- phy_disconnect(netdev->phydev);
-
- /* using phydev here as phy_disconnect NULLs netdev->phydev */
- if (phy_is_pseudo_fixed_link(phydev))
- fixed_phy_unregister(phydev);
-
-}
-
static void lan743x_phy_interface_select(struct lan743x_adapter *adapter)
{
u32 id_rev;
@@ -1520,65 +1367,9 @@ static void lan743x_phy_interface_select(struct lan743x_adapter *adapter)
adapter->phy_interface = PHY_INTERFACE_MODE_MII;
else
adapter->phy_interface = PHY_INTERFACE_MODE_RGMII;
-}
-
-static int lan743x_phy_open(struct lan743x_adapter *adapter)
-{
- struct net_device *netdev = adapter->netdev;
- struct lan743x_phy *phy = &adapter->phy;
- struct fixed_phy_status fphy_status = {
- .link = 1,
- .speed = SPEED_1000,
- .duplex = DUPLEX_FULL,
- };
- struct phy_device *phydev;
- int ret = -EIO;
-
- /* try devicetree phy, or fixed link */
- phydev = of_phy_get_and_connect(netdev, adapter->pdev->dev.of_node,
- lan743x_phy_link_status_change);
-
- if (!phydev) {
- /* try internal phy */
- phydev = phy_find_first(adapter->mdiobus);
- if (!phydev) {
- if ((adapter->csr.id_rev & ID_REV_ID_MASK_) ==
- ID_REV_ID_LAN7431_) {
- phydev = fixed_phy_register(PHY_POLL,
- &fphy_status, NULL);
- if (IS_ERR(phydev)) {
- netdev_err(netdev, "No PHY/fixed_PHY found\n");
- return PTR_ERR(phydev);
- }
- } else {
- goto return_error;
- }
- }
- lan743x_phy_interface_select(adapter);
-
- ret = phy_connect_direct(netdev, phydev,
- lan743x_phy_link_status_change,
- adapter->phy_interface);
- if (ret)
- goto return_error;
- }
-
- /* MAC doesn't support 1000T Half */
- phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
-
- /* support both flow controls */
- phy_support_asym_pause(phydev);
- phy->fc_request_control = (FLOW_CTRL_RX | FLOW_CTRL_TX);
- phy->fc_autoneg = phydev->autoneg;
-
- phy_start(phydev);
- phy_start_aneg(phydev);
- phy_attached_info(phydev);
- return 0;
-
-return_error:
- return ret;
+ netif_dbg(adapter, drv, adapter->netdev,
+ "selected phy interface: 0x%X\n", adapter->phy_interface);
}
static void lan743x_rfe_open(struct lan743x_adapter *adapter)
@@ -3079,6 +2870,350 @@ static int lan743x_rx_open(struct lan743x_rx *rx)
return ret;
}
+static int lan743x_phylink_sgmii_config(struct lan743x_adapter *adapter)
+{
+ u32 sgmii_ctl;
+ int ret;
+
+ ret = lan743x_get_lsd(SPEED_1000, DUPLEX_FULL,
+ MASTER_SLAVE_STATE_MASTER);
+ if (ret < 0) {
+ netif_err(adapter, drv, adapter->netdev,
+ "error %d link-speed-duplex(LSD) invalid\n", ret);
+ return ret;
+ }
+
+ adapter->sgmii_lsd = ret;
+ netif_dbg(adapter, drv, adapter->netdev,
+ "Link Speed Duplex (lsd) : 0x%X\n", adapter->sgmii_lsd);
+
+ /* LINK_STATUS_SOURCE from the External PHY via SGMII */
+ sgmii_ctl = lan743x_csr_read(adapter, SGMII_CTL);
+ sgmii_ctl &= ~SGMII_CTL_LINK_STATUS_SOURCE_;
+ lan743x_csr_write(adapter, SGMII_CTL, sgmii_ctl);
+
+ ret = lan743x_serdes_clock_and_aneg_update(adapter);
+ if (ret < 0) {
+ netif_err(adapter, drv, adapter->netdev,
+ "error %d sgmii aneg update failed\n", ret);
+ return ret;
+ }
+
+ return lan743x_pcs_power_reset(adapter);
+}
+
+static int lan743x_phylink_1000basex_config(struct lan743x_adapter *adapter)
+{
+ u32 sgmii_ctl;
+ int ret;
+
+ ret = lan743x_get_lsd(SPEED_1000, DUPLEX_FULL,
+ MASTER_SLAVE_STATE_MASTER);
+ if (ret < 0) {
+ netif_err(adapter, drv, adapter->netdev,
+ "error %d link-speed-duplex(LSD) invalid\n", ret);
+ return ret;
+ }
+
+ adapter->sgmii_lsd = ret;
+ netif_dbg(adapter, drv, adapter->netdev,
+ "Link Speed Duplex (lsd) : 0x%X\n", adapter->sgmii_lsd);
+
+ /* LINK_STATUS_SOURCE from 1000BASE-X PCS link status */
+ sgmii_ctl = lan743x_csr_read(adapter, SGMII_CTL);
+ sgmii_ctl |= SGMII_CTL_LINK_STATUS_SOURCE_;
+ lan743x_csr_write(adapter, SGMII_CTL, sgmii_ctl);
+
+ ret = lan743x_serdes_clock_and_aneg_update(adapter);
+ if (ret < 0) {
+ netif_err(adapter, drv, adapter->netdev,
+ "error %d 1000basex aneg update failed\n", ret);
+ return ret;
+ }
+
+ return lan743x_pcs_power_reset(adapter);
+}
+
+static int lan743x_phylink_2500basex_config(struct lan743x_adapter *adapter)
+{
+ u32 sgmii_ctl;
+ int ret;
+
+ ret = lan743x_get_lsd(SPEED_2500, DUPLEX_FULL,
+ MASTER_SLAVE_STATE_MASTER);
+ if (ret < 0) {
+ netif_err(adapter, drv, adapter->netdev,
+ "error %d link-speed-duplex(LSD) invalid\n", ret);
+ return ret;
+ }
+
+ adapter->sgmii_lsd = ret;
+ netif_dbg(adapter, drv, adapter->netdev,
+ "Link Speed Duplex (lsd) : 0x%X\n", adapter->sgmii_lsd);
+
+ /* LINK_STATUS_SOURCE from 2500BASE-X PCS link status */
+ sgmii_ctl = lan743x_csr_read(adapter, SGMII_CTL);
+ sgmii_ctl |= SGMII_CTL_LINK_STATUS_SOURCE_;
+ lan743x_csr_write(adapter, SGMII_CTL, sgmii_ctl);
+
+ ret = lan743x_serdes_clock_and_aneg_update(adapter);
+ if (ret < 0) {
+ netif_err(adapter, drv, adapter->netdev,
+ "error %d 2500basex aneg update failed\n", ret);
+ return ret;
+ }
+
+ return lan743x_pcs_power_reset(adapter);
+}
+
+static void lan743x_phylink_mac_config(struct phylink_config *config,
+ unsigned int link_an_mode,
+ const struct phylink_link_state *state)
+{
+ struct net_device *netdev = to_net_dev(config->dev);
+ struct lan743x_adapter *adapter = netdev_priv(netdev);
+ int ret;
+
+ switch (state->interface) {
+ case PHY_INTERFACE_MODE_2500BASEX:
+ ret = lan743x_phylink_2500basex_config(adapter);
+ if (ret < 0)
+ netif_err(adapter, drv, adapter->netdev,
+ "2500BASEX config failed. Error %d\n", ret);
+ else
+ netif_dbg(adapter, drv, adapter->netdev,
+ "2500BASEX mode selected and configured\n");
+ break;
+ case PHY_INTERFACE_MODE_1000BASEX:
+ ret = lan743x_phylink_1000basex_config(adapter);
+ if (ret < 0)
+ netif_err(adapter, drv, adapter->netdev,
+ "1000BASEX config failed. Error %d\n", ret);
+ else
+ netif_dbg(adapter, drv, adapter->netdev,
+ "1000BASEX mode selected and configured\n");
+ break;
+ case PHY_INTERFACE_MODE_SGMII:
+ ret = lan743x_phylink_sgmii_config(adapter);
+ if (ret < 0)
+ netif_err(adapter, drv, adapter->netdev,
+ "SGMII config failed. Error %d\n", ret);
+ else
+ netif_dbg(adapter, drv, adapter->netdev,
+ "SGMII mode selected and configured\n");
+ break;
+ default:
+ netif_dbg(adapter, drv, adapter->netdev,
+ "RGMII/GMII/MII(0x%X) mode enable\n", state->interface);
+ break;
+ }
+}
+
+static void lan743x_phylink_mac_link_down(struct phylink_config *config,
+ unsigned int link_an_mode,
+ phy_interface_t interface)
+{
+ netif_tx_stop_all_queues(to_net_dev(config->dev));
+}
+
+static void lan743x_phylink_mac_link_up(struct phylink_config *config,
+ struct phy_device *phydev,
+ unsigned int link_an_mode,
+ phy_interface_t interface,
+ int speed, int duplex,
+ bool tx_pause, bool rx_pause)
+{
+ struct net_device *netdev = to_net_dev(config->dev);
+ struct lan743x_adapter *adapter = netdev_priv(netdev);
+ int mac_cr;
+ u8 cap;
+
+ mac_cr = lan743x_csr_read(adapter, MAC_CR);
+ /* Pre-initialize register bits.
+ * Resulting value corresponds to SPEED_10
+ */
+ mac_cr &= ~(MAC_CR_CFG_H_ | MAC_CR_CFG_L_);
+ if (speed == SPEED_2500)
+ mac_cr |= MAC_CR_CFG_H_ | MAC_CR_CFG_L_;
+ else if (speed == SPEED_1000)
+ mac_cr |= MAC_CR_CFG_H_;
+ else if (speed == SPEED_100)
+ mac_cr |= MAC_CR_CFG_L_;
+
+ lan743x_csr_write(adapter, MAC_CR, mac_cr);
+
+ lan743x_ptp_update_latency(adapter, speed);
+
+ /* Flow Control operation */
+ cap = 0;
+ if (tx_pause)
+ cap |= FLOW_CTRL_TX;
+ if (rx_pause)
+ cap |= FLOW_CTRL_RX;
+
+ lan743x_mac_flow_ctrl_set_enables(adapter,
+ cap & FLOW_CTRL_TX,
+ cap & FLOW_CTRL_RX);
+
+ netif_tx_wake_all_queues(netdev);
+}
+
+static const struct phylink_mac_ops lan743x_phylink_mac_ops = {
+ .mac_config = lan743x_phylink_mac_config,
+ .mac_link_down = lan743x_phylink_mac_link_down,
+ .mac_link_up = lan743x_phylink_mac_link_up,
+};
+
+static struct {
+ unsigned long mask;
+ int speed;
+ int duplex;
+} lan743x_mac_caps_params[] = {
+ { MAC_2500FD, SPEED_2500, DUPLEX_FULL },
+ { MAC_1000FD, SPEED_1000, DUPLEX_FULL },
+ { MAC_100FD, SPEED_100, DUPLEX_FULL },
+ { MAC_10FD, SPEED_10, DUPLEX_FULL },
+ { MAC_100HD, SPEED_100, DUPLEX_HALF },
+ { MAC_10HD, SPEED_10, DUPLEX_HALF },
+};
+
+static int lan743x_find_max_speed(unsigned long caps, int *speed, int *duplex)
+{
+ int i;
+
+ *speed = SPEED_UNKNOWN;
+ *duplex = DUPLEX_UNKNOWN;
+ for (i = 0; i < ARRAY_SIZE(lan743x_mac_caps_params); i++) {
+ if (caps & lan743x_mac_caps_params[i].mask) {
+ *speed = lan743x_mac_caps_params[i].speed;
+ *duplex = lan743x_mac_caps_params[i].duplex;
+ break;
+ }
+ }
+
+ return *speed == SPEED_UNKNOWN ? -EINVAL : 0;
+}
+
+static int lan743x_phylink_create(struct lan743x_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct phylink *pl;
+
+ adapter->phylink_config.dev = &netdev->dev;
+ adapter->phylink_config.type = PHYLINK_NETDEV;
+ adapter->phylink_config.mac_managed_pm = false;
+
+ adapter->phylink_config.mac_capabilities = MAC_ASYM_PAUSE |
+ MAC_SYM_PAUSE | MAC_10 | MAC_100 | MAC_1000FD;
+
+ lan743x_phy_interface_select(adapter);
+
+ switch (adapter->phy_interface) {
+ case PHY_INTERFACE_MODE_SGMII:
+ __set_bit(PHY_INTERFACE_MODE_SGMII,
+ adapter->phylink_config.supported_interfaces);
+ __set_bit(PHY_INTERFACE_MODE_1000BASEX,
+ adapter->phylink_config.supported_interfaces);
+ __set_bit(PHY_INTERFACE_MODE_2500BASEX,
+ adapter->phylink_config.supported_interfaces);
+ adapter->phylink_config.mac_capabilities |= MAC_2500FD;
+ break;
+ case PHY_INTERFACE_MODE_GMII:
+ __set_bit(PHY_INTERFACE_MODE_GMII,
+ adapter->phylink_config.supported_interfaces);
+ break;
+ case PHY_INTERFACE_MODE_MII:
+ __set_bit(PHY_INTERFACE_MODE_MII,
+ adapter->phylink_config.supported_interfaces);
+ break;
+ default:
+ phy_interface_set_rgmii(adapter->phylink_config.supported_interfaces);
+ }
+
+ pl = phylink_create(&adapter->phylink_config, NULL,
+ adapter->phy_interface, &lan743x_phylink_mac_ops);
+
+ if (IS_ERR(pl)) {
+ netdev_err(netdev, "Could not create phylink (%pe)\n", pl);
+ return PTR_ERR(pl);
+ }
+
+ adapter->phylink = pl;
+ netdev_dbg(netdev, "lan743x phylink created");
+
+ return 0;
+}
+
+static bool lan743x_phy_handle_exists(struct device_node *dn)
+{
+ dn = of_parse_phandle(dn, "phy-handle", 0);
+ of_node_put(dn);
+ return dn != NULL;
+}
+
+static int lan743x_phylink_connect(struct lan743x_adapter *adapter)
+{
+ struct device_node *dn = adapter->pdev->dev.of_node;
+ struct net_device *dev = adapter->netdev;
+ struct phy_device *phydev;
+ int ret;
+
+ if (dn)
+ ret = phylink_of_phy_connect(adapter->phylink, dn, 0);
+
+ if (!dn || (ret && !lan743x_phy_handle_exists(dn))) {
+ phydev = phy_find_first(adapter->mdiobus);
+ if (phydev) {
+ /* attach the mac to the phy */
+ ret = phylink_connect_phy(adapter->phylink, phydev);
+ } else if (((adapter->csr.id_rev & ID_REV_ID_MASK_) ==
+ ID_REV_ID_LAN7431_) || adapter->is_pci11x1x) {
+ struct phylink_link_state state;
+ unsigned long caps;
+
+ caps = adapter->phylink_config.mac_capabilities;
+ ret = lan743x_find_max_speed(caps, &state.speed,
+ &state.duplex);
+ if (ret) {
+ netdev_err(dev, "find unknown speed (%d)\n",
+ ret);
+ return ret;
+ }
+
+ ret = phylink_set_fixed_link(adapter->phylink, &state);
+ if (ret) {
+ netdev_err(dev, "Could not set fixed link\n");
+ return ret;
+ }
+ } else {
+ netdev_err(dev, "no PHY found\n");
+ return -ENXIO;
+ }
+ }
+
+ if (ret) {
+ netdev_err(dev, "Could not attach PHY (%d)\n", ret);
+ return ret;
+ }
+
+ phylink_start(adapter->phylink);
+
+ return 0;
+}
+
+static void lan743x_phylink_disconnect(struct lan743x_adapter *adapter)
+{
+ struct net_device *netdev = adapter->netdev;
+ struct phy_device *phydev = netdev->phydev;
+
+ phylink_stop(adapter->phylink);
+ phylink_disconnect_phy(adapter->phylink);
+
+ if (phydev)
+ if (phy_is_pseudo_fixed_link(phydev))
+ fixed_phy_unregister(phydev);
+}
+
static int lan743x_netdev_close(struct net_device *netdev)
{
struct lan743x_adapter *adapter = netdev_priv(netdev);
@@ -3092,7 +3227,7 @@ static int lan743x_netdev_close(struct net_device *netdev)
lan743x_ptp_close(adapter);
- lan743x_phy_close(adapter);
+ lan743x_phylink_disconnect(adapter);
lan743x_mac_close(adapter);
@@ -3115,13 +3250,13 @@ static int lan743x_netdev_open(struct net_device *netdev)
if (ret)
goto close_intr;
- ret = lan743x_phy_open(adapter);
+ ret = lan743x_phylink_connect(adapter);
if (ret)
goto close_mac;
ret = lan743x_ptp_open(adapter);
if (ret)
- goto close_phy;
+ goto close_mac;
lan743x_rfe_open(adapter);
@@ -3161,9 +3296,8 @@ static int lan743x_netdev_open(struct net_device *netdev)
lan743x_rx_close(&adapter->rx[index]);
}
lan743x_ptp_close(adapter);
-
-close_phy:
- lan743x_phy_close(adapter);
+ if (adapter->phylink)
+ lan743x_phylink_disconnect(adapter);
close_mac:
lan743x_mac_close(adapter);
@@ -3192,11 +3326,14 @@ static netdev_tx_t lan743x_netdev_xmit_frame(struct sk_buff *skb,
static int lan743x_netdev_ioctl(struct net_device *netdev,
struct ifreq *ifr, int cmd)
{
+ struct lan743x_adapter *adapter = netdev_priv(netdev);
+
if (!netif_running(netdev))
return -EINVAL;
if (cmd == SIOCSHWTSTAMP)
return lan743x_ptp_ioctl(netdev, ifr, cmd);
- return phy_mii_ioctl(netdev->phydev, ifr, cmd);
+
+ return phylink_mii_ioctl(adapter->phylink, ifr, cmd);
}
static void lan743x_netdev_set_multicast(struct net_device *netdev)
@@ -3301,10 +3438,17 @@ static void lan743x_mdiobus_cleanup(struct lan743x_adapter *adapter)
mdiobus_unregister(adapter->mdiobus);
}
+static void lan743x_destroy_phylink(struct lan743x_adapter *adapter)
+{
+ phylink_destroy(adapter->phylink);
+ adapter->phylink = NULL;
+}
+
static void lan743x_full_cleanup(struct lan743x_adapter *adapter)
{
unregister_netdev(adapter->netdev);
+ lan743x_destroy_phylink(adapter);
lan743x_mdiobus_cleanup(adapter);
lan743x_hardware_cleanup(adapter);
lan743x_pci_cleanup(adapter);
@@ -3518,14 +3662,21 @@ static int lan743x_pcidev_probe(struct pci_dev *pdev,
NETIF_F_HW_CSUM | NETIF_F_RXCSUM;
adapter->netdev->hw_features = adapter->netdev->features;
- /* carrier off reporting is important to ethtool even BEFORE open */
- netif_carrier_off(netdev);
+ ret = lan743x_phylink_create(adapter);
+ if (ret < 0) {
+ netif_err(adapter, probe, netdev,
+ "failed to setup phylink (%d)\n", ret);
+ goto cleanup_mdiobus;
+ }
ret = register_netdev(adapter->netdev);
if (ret < 0)
- goto cleanup_mdiobus;
+ goto cleanup_phylink;
return 0;
+cleanup_phylink:
+ lan743x_destroy_phylink(adapter);
+
cleanup_mdiobus:
lan743x_mdiobus_cleanup(adapter);
@@ -3781,6 +3932,7 @@ static int lan743x_pm_resume(struct device *dev)
MAC_WK_SRC_WK_FR_SAVED_;
lan743x_csr_write(adapter, MAC_WK_SRC, data);
+ rtnl_lock();
/* open netdev when netdev is at running state while resume.
* For instance, it is true when system wakesup after pm-suspend
* However, it is false when system wakes up after suspend GUI menu
@@ -3789,6 +3941,7 @@ static int lan743x_pm_resume(struct device *dev)
lan743x_netdev_open(netdev);
netif_device_attach(netdev);
+ rtnl_unlock();
return 0;
}
@@ -5,6 +5,7 @@
#define _LAN743X_H
#include <linux/phy.h>
+#include <linux/phylink.h>
#include "lan743x_ptp.h"
#define DRIVER_AUTHOR "Bryan Whitehead <Bryan.Whitehead@microchip.com>"
@@ -1083,6 +1084,8 @@ struct lan743x_adapter {
u32 flags;
u32 hw_cfg;
phy_interface_t phy_interface;
+ struct phylink *phylink;
+ struct phylink_config phylink_config;
};
#define LAN743X_COMPONENT_FLAG_RX(channel) BIT(20 + (channel))
Migrate phy support from phylib to phylink. Signed-off-by: Raju Lakkaraju <Raju.Lakkaraju@microchip.com> --- Change List: ============ V3 -> V4: - Add the Fixed-link by include the Russell King patch - Change lan743x_phylink_create( ) argument from netdev to adapter V2 -> V3: - Remove the unwanted parens in each of these if() sub-blocks - Replace "to_net_dev(config->dev)" with "netdev". - Add GMII_ID/RGMII_TXID/RGMII_RXID in supported_interfaces - Fix the lan743x_phy_handle_exists( ) return type V1 -> V2: - Split the PHYLINK and SFP changes in 2 different patch series drivers/net/ethernet/microchip/Kconfig | 5 +- drivers/net/ethernet/microchip/lan743x_main.c | 599 +++++++++++------- drivers/net/ethernet/microchip/lan743x_main.h | 3 + 3 files changed, 382 insertions(+), 225 deletions(-)