| Message ID | 20240913011635.1286027-1-quic_abchauha@quicinc.com (mailing list archive) |
|---|---|
| State | RFC |
| Delegated to: | Netdev Maintainers |
| Headers | show |
| Series | [RFC,net,v1] net: phy: aquantia: Set phy speed to 2.5gbps for AQR115c | expand |
Hi, On Thu, 12 Sep 2024 18:16:35 -0700 Abhishek Chauhan <quic_abchauha@quicinc.com> wrote: > Recently we observed that aquantia AQR115c always comes up in > 100Mbps mode. AQR115c aquantia chip supports max speed up to > 2.5Gbps. Today the AQR115c configuration is done through > aqr113c_config_init which internally calls aqr107_config_init. > aqr113c and aqr107 are both capable of 10Gbps. Whereas AQR115c > supprts max speed of 2.5Gbps only. > > Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c") > Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> > --- > drivers/net/phy/aquantia/aquantia_main.c | 7 +++++++ > 1 file changed, 7 insertions(+) > > diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c > index e982e9ce44a5..9afc041dbb64 100644 > --- a/drivers/net/phy/aquantia/aquantia_main.c > +++ b/drivers/net/phy/aquantia/aquantia_main.c > @@ -499,6 +499,12 @@ static int aqr107_config_init(struct phy_device *phydev) > if (!ret) > aqr107_chip_info(phydev); > > + /* AQR115c supports speed up to 2.5Gbps */ > + if (phydev->interface == PHY_INTERFACE_MODE_2500BASEX) { > + phy_set_max_speed(phydev, SPEED_2500); > + phydev->autoneg = AUTONEG_ENABLE; > + } > + If I get your commit log right, the code above will also apply for ASQR107, AQR113 and so on, don't you risk breaking these PHYs if they are in 2500BASEX mode at boot? Besides that, if the PHY switches between SGMII and 2500BASEX dynamically depending on the link speed, it could be that it's configured by default in SGMII, hence this check will be missed. Is the AQR115c in the same situation as AQR111 for example, where the PMA capabilities reported are incorrect ? If so, you can take the same approach as aqr111, which is to create a dedicated .config_init() callback for the AQR115c, which sets the max speed, then call aqr113c_config_init() from there ? Maxime
On 9/13/2024 1:01 AM, Maxime Chevallier wrote: > Hi, > > On Thu, 12 Sep 2024 18:16:35 -0700 > Abhishek Chauhan <quic_abchauha@quicinc.com> wrote: > >> Recently we observed that aquantia AQR115c always comes up in >> 100Mbps mode. AQR115c aquantia chip supports max speed up to >> 2.5Gbps. Today the AQR115c configuration is done through >> aqr113c_config_init which internally calls aqr107_config_init. >> aqr113c and aqr107 are both capable of 10Gbps. Whereas AQR115c >> supprts max speed of 2.5Gbps only. >> >> Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c") >> Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> >> --- >> drivers/net/phy/aquantia/aquantia_main.c | 7 +++++++ >> 1 file changed, 7 insertions(+) >> >> diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c >> index e982e9ce44a5..9afc041dbb64 100644 >> --- a/drivers/net/phy/aquantia/aquantia_main.c >> +++ b/drivers/net/phy/aquantia/aquantia_main.c >> @@ -499,6 +499,12 @@ static int aqr107_config_init(struct phy_device *phydev) >> if (!ret) >> aqr107_chip_info(phydev); >> >> + /* AQR115c supports speed up to 2.5Gbps */ >> + if (phydev->interface == PHY_INTERFACE_MODE_2500BASEX) { >> + phy_set_max_speed(phydev, SPEED_2500); >> + phydev->autoneg = AUTONEG_ENABLE; >> + } >> + > > If I get your commit log right, the code above will also apply for > ASQR107, AQR113 and so on, don't you risk breaking these PHYs if they > are in 2500BASEX mode at boot? > I was thinking of the same. That this might break something here for other Phy chip. As every phy shares the same config init. Hence the reason for RFC. > Besides that, if the PHY switches between SGMII and 2500BASEX > dynamically depending on the link speed, it could be that it's > configured by default in SGMII, hence this check will be missed. > > Is the AQR115c in the same situation as AQR111 for example, where the > PMA capabilities reported are incorrect ? If so, you can take the same > approach as aqr111, which is to create a dedicated .config_init() > callback for the AQR115c, which sets the max speed, then call > aqr113c_config_init() from there ? > I think the better way is to have AQR115c its own config_init which sets the max speed to 2.5Gbps and then call aqr113c_config_init . I will clean up the config_init and Thanks for the review comments. > Maxime
On Fri, Sep 13, 2024 at 09:12:13AM -0700, Abhishek Chauhan (ABC) wrote: > > > On 9/13/2024 1:01 AM, Maxime Chevallier wrote: > > Hi, > > > > On Thu, 12 Sep 2024 18:16:35 -0700 > > Abhishek Chauhan <quic_abchauha@quicinc.com> wrote: > > > >> Recently we observed that aquantia AQR115c always comes up in > >> 100Mbps mode. AQR115c aquantia chip supports max speed up to > >> 2.5Gbps. Today the AQR115c configuration is done through > >> aqr113c_config_init which internally calls aqr107_config_init. > >> aqr113c and aqr107 are both capable of 10Gbps. Whereas AQR115c > >> supprts max speed of 2.5Gbps only. > >> > >> Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c") > >> Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> > >> --- > >> drivers/net/phy/aquantia/aquantia_main.c | 7 +++++++ > >> 1 file changed, 7 insertions(+) > >> > >> diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c > >> index e982e9ce44a5..9afc041dbb64 100644 > >> --- a/drivers/net/phy/aquantia/aquantia_main.c > >> +++ b/drivers/net/phy/aquantia/aquantia_main.c > >> @@ -499,6 +499,12 @@ static int aqr107_config_init(struct phy_device *phydev) > >> if (!ret) > >> aqr107_chip_info(phydev); > >> > >> + /* AQR115c supports speed up to 2.5Gbps */ > >> + if (phydev->interface == PHY_INTERFACE_MODE_2500BASEX) { > >> + phy_set_max_speed(phydev, SPEED_2500); > >> + phydev->autoneg = AUTONEG_ENABLE; > >> + } > >> + > > > > If I get your commit log right, the code above will also apply for > > ASQR107, AQR113 and so on, don't you risk breaking these PHYs if they > > are in 2500BASEX mode at boot? > > > > I was thinking of the same. That this might break something here for other Phy chip. > As every phy shares the same config init. Hence the reason for RFC. > > > Besides that, if the PHY switches between SGMII and 2500BASEX > > dynamically depending on the link speed, it could be that it's > > configured by default in SGMII, hence this check will be missed. > > > > > I think the better way is to have AQR115c its own config_init which sets > the max speed to 2.5Gbps and then call aqr113c_config_init . phy_set_max_speed(phydev, SPEED_2500) is something a MAC does, not a PHY. It is a way for the MAC to say is supports less than the PHY. I would say the current aqcs109_config_init() is doing this wrong. > > Is the AQR115c in the same situation as AQR111 for example, where the > > PMA capabilities reported are incorrect ? This is the approach to follow. The PHY registers should report what it is actually capable of. But some aquantia PHYs get this wrong. Please check if this is also true for your PHY. Look at what genphy_c45_pma_read_abilities() is doing. You might need to implement a .get_feature callback for this PHY which first calls genphy_c45_pma_read_abilities() and then manually fixes up what the PHY gets wrong. Andrew
On 9/13/2024 9:35 AM, Andrew Lunn wrote: > On Fri, Sep 13, 2024 at 09:12:13AM -0700, Abhishek Chauhan (ABC) wrote: >> >> >> On 9/13/2024 1:01 AM, Maxime Chevallier wrote: >>> Hi, >>> >>> On Thu, 12 Sep 2024 18:16:35 -0700 >>> Abhishek Chauhan <quic_abchauha@quicinc.com> wrote: >>> >>>> Recently we observed that aquantia AQR115c always comes up in >>>> 100Mbps mode. AQR115c aquantia chip supports max speed up to >>>> 2.5Gbps. Today the AQR115c configuration is done through >>>> aqr113c_config_init which internally calls aqr107_config_init. >>>> aqr113c and aqr107 are both capable of 10Gbps. Whereas AQR115c >>>> supprts max speed of 2.5Gbps only. >>>> >>>> Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c") >>>> Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> >>>> --- >>>> drivers/net/phy/aquantia/aquantia_main.c | 7 +++++++ >>>> 1 file changed, 7 insertions(+) >>>> >>>> diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c >>>> index e982e9ce44a5..9afc041dbb64 100644 >>>> --- a/drivers/net/phy/aquantia/aquantia_main.c >>>> +++ b/drivers/net/phy/aquantia/aquantia_main.c >>>> @@ -499,6 +499,12 @@ static int aqr107_config_init(struct phy_device *phydev) >>>> if (!ret) >>>> aqr107_chip_info(phydev); >>>> >>>> + /* AQR115c supports speed up to 2.5Gbps */ >>>> + if (phydev->interface == PHY_INTERFACE_MODE_2500BASEX) { >>>> + phy_set_max_speed(phydev, SPEED_2500); >>>> + phydev->autoneg = AUTONEG_ENABLE; >>>> + } >>>> + >>> >>> If I get your commit log right, the code above will also apply for >>> ASQR107, AQR113 and so on, don't you risk breaking these PHYs if they >>> are in 2500BASEX mode at boot? >>> >> >> I was thinking of the same. That this might break something here for other Phy chip. >> As every phy shares the same config init. Hence the reason for RFC. >> >>> Besides that, if the PHY switches between SGMII and 2500BASEX >>> dynamically depending on the link speed, it could be that it's >>> configured by default in SGMII, hence this check will be missed. >>> >>> >> I think the better way is to have AQR115c its own config_init which sets >> the max speed to 2.5Gbps and then call aqr113c_config_init . > Noted! > phy_set_max_speed(phydev, SPEED_2500) is something a MAC does, not a > PHY. It is a way for the MAC to say is supports less than the PHY. I > would say the current aqcs109_config_init() is doing this wrong. > >>> Is the AQR115c in the same situation as AQR111 for example, where the >>> PMA capabilities reported are incorrect ? > > This is the approach to follow. The PHY registers should report what > it is actually capable of. But some aquantia PHYs get this > wrong. Please check if this is also true for your PHY. Look at what > genphy_c45_pma_read_abilities() is doing. > > You might need to implement a .get_feature callback for this PHY which > first calls genphy_c45_pma_read_abilities() and then manually fixes up > what the PHY gets wrong. > Thanks alot Andrew. I will get back to you with my analysis on AQR115c phy. Most likely the pma abilities are reported incorrectly. > Andrew
On Fri, Sep 13, 2024 at 06:35:17PM +0200, Andrew Lunn wrote: > On Fri, Sep 13, 2024 at 09:12:13AM -0700, Abhishek Chauhan (ABC) wrote: > > On 9/13/2024 1:01 AM, Maxime Chevallier wrote: > > > Hi, > > > > > > On Thu, 12 Sep 2024 18:16:35 -0700 > > > Abhishek Chauhan <quic_abchauha@quicinc.com> wrote: > > > > > >> Recently we observed that aquantia AQR115c always comes up in > > >> 100Mbps mode. AQR115c aquantia chip supports max speed up to > > >> 2.5Gbps. Today the AQR115c configuration is done through > > >> aqr113c_config_init which internally calls aqr107_config_init. > > >> aqr113c and aqr107 are both capable of 10Gbps. Whereas AQR115c > > >> supprts max speed of 2.5Gbps only. > > >> > > >> Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c") > > >> Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> > > >> --- > > >> drivers/net/phy/aquantia/aquantia_main.c | 7 +++++++ > > >> 1 file changed, 7 insertions(+) > > >> > > >> diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c > > >> index e982e9ce44a5..9afc041dbb64 100644 > > >> --- a/drivers/net/phy/aquantia/aquantia_main.c > > >> +++ b/drivers/net/phy/aquantia/aquantia_main.c > > >> @@ -499,6 +499,12 @@ static int aqr107_config_init(struct phy_device *phydev) > > >> if (!ret) > > >> aqr107_chip_info(phydev); > > >> > > >> + /* AQR115c supports speed up to 2.5Gbps */ > > >> + if (phydev->interface == PHY_INTERFACE_MODE_2500BASEX) { > > >> + phy_set_max_speed(phydev, SPEED_2500); > > >> + phydev->autoneg = AUTONEG_ENABLE; > > >> + } > > >> + > > > > > > If I get your commit log right, the code above will also apply for > > > ASQR107, AQR113 and so on, don't you risk breaking these PHYs if they > > > are in 2500BASEX mode at boot? > > > > > > > I was thinking of the same. That this might break something here for other Phy chip. > > As every phy shares the same config init. Hence the reason for RFC. > > > > > Besides that, if the PHY switches between SGMII and 2500BASEX > > > dynamically depending on the link speed, it could be that it's > > > configured by default in SGMII, hence this check will be missed. > > > > > > > > I think the better way is to have AQR115c its own config_init which sets > > the max speed to 2.5Gbps and then call aqr113c_config_init . > > phy_set_max_speed(phydev, SPEED_2500) is something a MAC does, not a > PHY. It is a way for the MAC to say is supports less than the PHY. I > would say the current aqcs109_config_init() is doing this wrong. Agreed on two points: 1) phy_set_max_speed() is documented as a function that the MAC will call. 2) calling phy_set_max_speed() in .config_init() is way too late for phylink. .config_init() is called from phy_init_hw(), which happens after the PHY has been attached. However, phylink needs to know what the PHY supports _before_ that, especially for any PHY that is on a SFP, so it can determine what interface to use for the PHY. So, as Andrew says, the current aqcs109_config_init(), and it seems aqr111_config_init() are both broken. The PHY driver needs to indicate to phylib what is supported by the PHY no later than the .get_features() method. Thanks.
On 9/17/2024 2:31 AM, Russell King (Oracle) wrote: > On Fri, Sep 13, 2024 at 06:35:17PM +0200, Andrew Lunn wrote: >> On Fri, Sep 13, 2024 at 09:12:13AM -0700, Abhishek Chauhan (ABC) wrote: >>> On 9/13/2024 1:01 AM, Maxime Chevallier wrote: >>>> Hi, >>>> >>>> On Thu, 12 Sep 2024 18:16:35 -0700 >>>> Abhishek Chauhan <quic_abchauha@quicinc.com> wrote: >>>> >>>>> Recently we observed that aquantia AQR115c always comes up in >>>>> 100Mbps mode. AQR115c aquantia chip supports max speed up to >>>>> 2.5Gbps. Today the AQR115c configuration is done through >>>>> aqr113c_config_init which internally calls aqr107_config_init. >>>>> aqr113c and aqr107 are both capable of 10Gbps. Whereas AQR115c >>>>> supprts max speed of 2.5Gbps only. >>>>> >>>>> Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c") >>>>> Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> >>>>> --- >>>>> drivers/net/phy/aquantia/aquantia_main.c | 7 +++++++ >>>>> 1 file changed, 7 insertions(+) >>>>> >>>>> diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c >>>>> index e982e9ce44a5..9afc041dbb64 100644 >>>>> --- a/drivers/net/phy/aquantia/aquantia_main.c >>>>> +++ b/drivers/net/phy/aquantia/aquantia_main.c >>>>> @@ -499,6 +499,12 @@ static int aqr107_config_init(struct phy_device *phydev) >>>>> if (!ret) >>>>> aqr107_chip_info(phydev); >>>>> >>>>> + /* AQR115c supports speed up to 2.5Gbps */ >>>>> + if (phydev->interface == PHY_INTERFACE_MODE_2500BASEX) { >>>>> + phy_set_max_speed(phydev, SPEED_2500); >>>>> + phydev->autoneg = AUTONEG_ENABLE; >>>>> + } >>>>> + >>>> >>>> If I get your commit log right, the code above will also apply for >>>> ASQR107, AQR113 and so on, don't you risk breaking these PHYs if they >>>> are in 2500BASEX mode at boot? >>>> >>> >>> I was thinking of the same. That this might break something here for other Phy chip. >>> As every phy shares the same config init. Hence the reason for RFC. >>> >>>> Besides that, if the PHY switches between SGMII and 2500BASEX >>>> dynamically depending on the link speed, it could be that it's >>>> configured by default in SGMII, hence this check will be missed. >>>> >>>> >>> I think the better way is to have AQR115c its own config_init which sets >>> the max speed to 2.5Gbps and then call aqr113c_config_init . >> >> phy_set_max_speed(phydev, SPEED_2500) is something a MAC does, not a >> PHY. It is a way for the MAC to say is supports less than the PHY. I >> would say the current aqcs109_config_init() is doing this wrong. > > Agreed on two points: > > 1) phy_set_max_speed() is documented as a function that the MAC will > call. > > 2) calling phy_set_max_speed() in .config_init() is way too late for > phylink. .config_init() is called from phy_init_hw(), which happens > after the PHY has been attached. However, phylink needs to know what > the PHY supports _before_ that, especially for any PHY that is on a > SFP, so it can determine what interface to use for the PHY. > > So, as Andrew says, the current aqcs109_config_init(), and it seems > aqr111_config_init() are both broken. > > The PHY driver needs to indicate to phylib what is supported by the > PHY no later than the .get_features() method. > Noted!. Makes sense. thanks for your review, Russell. We are in the process of figuring out what the phy chip is reporting as its features. Once done i will raise a clean patch for upstream review. > Thanks. >
On 9/17/2024 1:57 PM, Abhishek Chauhan (ABC) wrote: > > > On 9/17/2024 2:31 AM, Russell King (Oracle) wrote: >> On Fri, Sep 13, 2024 at 06:35:17PM +0200, Andrew Lunn wrote: >>> On Fri, Sep 13, 2024 at 09:12:13AM -0700, Abhishek Chauhan (ABC) wrote: >>>> On 9/13/2024 1:01 AM, Maxime Chevallier wrote: >>>>> Hi, >>>>> >>>>> On Thu, 12 Sep 2024 18:16:35 -0700 >>>>> Abhishek Chauhan <quic_abchauha@quicinc.com> wrote: >>>>> >>>>>> Recently we observed that aquantia AQR115c always comes up in >>>>>> 100Mbps mode. AQR115c aquantia chip supports max speed up to >>>>>> 2.5Gbps. Today the AQR115c configuration is done through >>>>>> aqr113c_config_init which internally calls aqr107_config_init. >>>>>> aqr113c and aqr107 are both capable of 10Gbps. Whereas AQR115c >>>>>> supprts max speed of 2.5Gbps only. >>>>>> >>>>>> Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c") >>>>>> Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> >>>>>> --- >>>>>> drivers/net/phy/aquantia/aquantia_main.c | 7 +++++++ >>>>>> 1 file changed, 7 insertions(+) >>>>>> >>>>>> diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c >>>>>> index e982e9ce44a5..9afc041dbb64 100644 >>>>>> --- a/drivers/net/phy/aquantia/aquantia_main.c >>>>>> +++ b/drivers/net/phy/aquantia/aquantia_main.c >>>>>> @@ -499,6 +499,12 @@ static int aqr107_config_init(struct phy_device *phydev) >>>>>> if (!ret) >>>>>> aqr107_chip_info(phydev); >>>>>> >>>>>> + /* AQR115c supports speed up to 2.5Gbps */ >>>>>> + if (phydev->interface == PHY_INTERFACE_MODE_2500BASEX) { >>>>>> + phy_set_max_speed(phydev, SPEED_2500); >>>>>> + phydev->autoneg = AUTONEG_ENABLE; >>>>>> + } >>>>>> + >>>>> >>>>> If I get your commit log right, the code above will also apply for >>>>> ASQR107, AQR113 and so on, don't you risk breaking these PHYs if they >>>>> are in 2500BASEX mode at boot? >>>>> >>>> >>>> I was thinking of the same. That this might break something here for other Phy chip. >>>> As every phy shares the same config init. Hence the reason for RFC. >>>> >>>>> Besides that, if the PHY switches between SGMII and 2500BASEX >>>>> dynamically depending on the link speed, it could be that it's >>>>> configured by default in SGMII, hence this check will be missed. >>>>> >>>>> >>>> I think the better way is to have AQR115c its own config_init which sets >>>> the max speed to 2.5Gbps and then call aqr113c_config_init . >>> >>> phy_set_max_speed(phydev, SPEED_2500) is something a MAC does, not a >>> PHY. It is a way for the MAC to say is supports less than the PHY. I >>> would say the current aqcs109_config_init() is doing this wrong. >> >> Agreed on two points: >> >> 1) phy_set_max_speed() is documented as a function that the MAC will >> call. >> >> 2) calling phy_set_max_speed() in .config_init() is way too late for >> phylink. .config_init() is called from phy_init_hw(), which happens >> after the PHY has been attached. However, phylink needs to know what >> the PHY supports _before_ that, especially for any PHY that is on a >> SFP, so it can determine what interface to use for the PHY. >> >> So, as Andrew says, the current aqcs109_config_init(), and it seems >> aqr111_config_init() are both broken. >> >> The PHY driver needs to indicate to phylib what is supported by the >> PHY no later than the .get_features() method. >> > > Noted!. Makes sense. thanks for your review, Russell. > We are in the process of figuring out what the phy chip is reporting as > its features. Once done i will raise a clean patch for upstream review. > Russell and Andrew we added prints and understood what the phy is reporting as part of the genphy_c45_pma_read_abilities [ 12.041576] MDIO_STAT2: 0xb301 [ 12.050722] MDIO_PMA_EXTABLE: 0x40fc From the PMA extensible register we see that the phy is reporting that it supports #define MDIO_PMA_EXTABLE_10GBT 0x0004 /* 10GBASE-T ability */ #define MDIO_PMA_EXTABLE_10GBKX4 0x0008 /* 10GBASE-KX4 ability */ #define MDIO_PMA_EXTABLE_10GBKR 0x0010 /* 10GBASE-KR ability */ #define MDIO_PMA_EXTABLE_1000BT 0x0020 /* 1000BASE-T ability */ #define MDIO_PMA_EXTABLE_1000BKX 0x0040 /* 1000BASE-KX ability */ #define MDIO_PMA_EXTABLE_100BTX 0x0080 /* 100BASE-TX ability */ #define MDIO_PMA_EXTABLE_NBT 0x4000 /* 2.5/5GBASE-T ability */ [ 12.060265] MDIO_PMA_NG_EXTABLE: 0x3 /* 2.5G/5G Extended abilities register. */ #define MDIO_PMA_NG_EXTABLE_2_5GBT 0x0001 /* 2.5GBASET ability */ #define MDIO_PMA_NG_EXTABLE_5GBT 0x0002 /* 5GBASET ability */ I feel that the phy here is incorrectly reporting all these abilities as AQR115c supports speeds only upto 2.5Gbps https://www.marvell.com/content/dam/marvell/en/public-collateral/transceivers/marvell-phys-transceivers-aqrate-gen4-product-brief.pdf AQR115C / AQR115 Single port, 2.5Gbps / 1Gbps / 100Mbps / 10Mbps 7 x 7 mm / 7 x 11 mm I feel like get_features for AQR115c is reporting wrong modes and hence the link is coming up and is negotiated at 100Mbps. (Misbehavior from AQR115c) From the MAC perspective we have ensure our max capabilities are 2.5 Gbps by setting the below from stmmac driver phylink_limit_mac_speed(config, 2500); I am thinking of solving this problem by having custom .get_features in the AQR115c driver to only set supported speeds upto 2.5gbps let me know what you think ? >> Thanks. >>
> Russell and Andrew > > we added prints and understood what the phy is reporting as part of the > genphy_c45_pma_read_abilities > > [ 12.041576] MDIO_STAT2: 0xb301 > > > [ 12.050722] MDIO_PMA_EXTABLE: 0x40fc > > >From the PMA extensible register we see that the phy is reporting that it supports > > #define MDIO_PMA_EXTABLE_10GBT 0x0004 /* 10GBASE-T ability */ > #define MDIO_PMA_EXTABLE_10GBKX4 0x0008 /* 10GBASE-KX4 ability */ > #define MDIO_PMA_EXTABLE_10GBKR 0x0010 /* 10GBASE-KR ability */ > #define MDIO_PMA_EXTABLE_1000BT 0x0020 /* 1000BASE-T ability */ > #define MDIO_PMA_EXTABLE_1000BKX 0x0040 /* 1000BASE-KX ability */ > #define MDIO_PMA_EXTABLE_100BTX 0x0080 /* 100BASE-TX ability */ > #define MDIO_PMA_EXTABLE_NBT 0x4000 /* 2.5/5GBASE-T ability */ > > [ 12.060265] MDIO_PMA_NG_EXTABLE: 0x3 > > /* 2.5G/5G Extended abilities register. */ > #define MDIO_PMA_NG_EXTABLE_2_5GBT 0x0001 /* 2.5GBASET ability */ > #define MDIO_PMA_NG_EXTABLE_5GBT 0x0002 /* 5GBASET ability */ > > I feel that the phy here is incorrectly reporting all these abilities as > AQR115c supports speeds only upto 2.5Gbps > https://www.marvell.com/content/dam/marvell/en/public-collateral/transceivers/marvell-phys-transceivers-aqrate-gen4-product-brief.pdf > > AQR115C / AQR115 Single port, 2.5Gbps / 1Gbps / 100Mbps / 10Mbps 7 x 7 mm / 7 x 11 mm One things to check. Are you sure you have the correct firmware? Many of the registers which the standards say should be Read Only can be influenced by the firmware. So the wrong firmware, or provisioning taken from another device could result in the wrong capabilities being set. You might want to report this issue to Marvell, but my guess would be, they don't care. I would guess the vendor driver ignores these registers and simply uses the product ID to determine what the device actually supports. > I am thinking of solving this problem by having > custom .get_features in the AQR115c driver to only set supported speeds > upto 2.5gbps Yes, that is the correct solution. It would also be good if you could, in a separate patch, change the aqcs109_config_init() to not call phy_set_max_speed() and add a custom .get_features. Andrew
On 9/18/2024 2:45 PM, Andrew Lunn wrote: >> Russell and Andrew >> >> we added prints and understood what the phy is reporting as part of the >> genphy_c45_pma_read_abilities >> >> [ 12.041576] MDIO_STAT2: 0xb301 >> >> >> [ 12.050722] MDIO_PMA_EXTABLE: 0x40fc >> >> >From the PMA extensible register we see that the phy is reporting that it supports >> >> #define MDIO_PMA_EXTABLE_10GBT 0x0004 /* 10GBASE-T ability */ >> #define MDIO_PMA_EXTABLE_10GBKX4 0x0008 /* 10GBASE-KX4 ability */ >> #define MDIO_PMA_EXTABLE_10GBKR 0x0010 /* 10GBASE-KR ability */ >> #define MDIO_PMA_EXTABLE_1000BT 0x0020 /* 1000BASE-T ability */ >> #define MDIO_PMA_EXTABLE_1000BKX 0x0040 /* 1000BASE-KX ability */ >> #define MDIO_PMA_EXTABLE_100BTX 0x0080 /* 100BASE-TX ability */ >> #define MDIO_PMA_EXTABLE_NBT 0x4000 /* 2.5/5GBASE-T ability */ >> >> [ 12.060265] MDIO_PMA_NG_EXTABLE: 0x3 >> >> /* 2.5G/5G Extended abilities register. */ >> #define MDIO_PMA_NG_EXTABLE_2_5GBT 0x0001 /* 2.5GBASET ability */ >> #define MDIO_PMA_NG_EXTABLE_5GBT 0x0002 /* 5GBASET ability */ >> >> I feel that the phy here is incorrectly reporting all these abilities as >> AQR115c supports speeds only upto 2.5Gbps >> https://www.marvell.com/content/dam/marvell/en/public-collateral/transceivers/marvell-phys-transceivers-aqrate-gen4-product-brief.pdf >> >> AQR115C / AQR115 Single port, 2.5Gbps / 1Gbps / 100Mbps / 10Mbps 7 x 7 mm / 7 x 11 mm > > One things to check. Are you sure you have the correct firmware? Many > of the registers which the standards say should be Read Only can be > influenced by the firmware. So the wrong firmware, or provisioning > taken from another device could result in the wrong capabilities being > set. > I did check with the hardware team and the firmware loaded is AQR-G4_v5.6.7-AQR_Marvell_NoSwap_XFI2500SGMII_ID44842_VER1922.cld Only Marvell folks can tell me what is inside the FW. Let me double check with Marvell on this and ask them why is the phy reporting all these PMA capabilities. > You might want to report this issue to Marvell, but my guess would be, > they don't care. I would guess the vendor driver ignores these > registers and simply uses the product ID to determine what the device > actually supports. > >> I am thinking of solving this problem by having >> custom .get_features in the AQR115c driver to only set supported speeds >> upto 2.5gbps > > Yes, that is the correct solution. > It would also be good if you could, in a separate patch, change the > aqcs109_config_init() to not call phy_set_max_speed() and add a custom > .get_features. Let me raise this patch in a day or two for upstream review after testing it out locally on AQR115c > > Andrew
diff --git a/drivers/net/phy/aquantia/aquantia_main.c b/drivers/net/phy/aquantia/aquantia_main.c index e982e9ce44a5..9afc041dbb64 100644 --- a/drivers/net/phy/aquantia/aquantia_main.c +++ b/drivers/net/phy/aquantia/aquantia_main.c @@ -499,6 +499,12 @@ static int aqr107_config_init(struct phy_device *phydev) if (!ret) aqr107_chip_info(phydev); + /* AQR115c supports speed up to 2.5Gbps */ + if (phydev->interface == PHY_INTERFACE_MODE_2500BASEX) { + phy_set_max_speed(phydev, SPEED_2500); + phydev->autoneg = AUTONEG_ENABLE; + } + ret = aqr107_set_downshift(phydev, MDIO_AN_VEND_PROV_DOWNSHIFT_DFLT); if (ret) return ret; @@ -1036,6 +1042,7 @@ static struct phy_driver aqr_driver[] = { .get_sset_count = aqr107_get_sset_count, .get_strings = aqr107_get_strings, .get_stats = aqr107_get_stats, + .get_features = genphy_c45_pma_read_abilities, .link_change_notify = aqr107_link_change_notify, .led_brightness_set = aqr_phy_led_brightness_set, .led_hw_is_supported = aqr_phy_led_hw_is_supported,
Recently we observed that aquantia AQR115c always comes up in 100Mbps mode. AQR115c aquantia chip supports max speed up to 2.5Gbps. Today the AQR115c configuration is done through aqr113c_config_init which internally calls aqr107_config_init. aqr113c and aqr107 are both capable of 10Gbps. Whereas AQR115c supprts max speed of 2.5Gbps only. Fixes: 0ebc581f8a4b ("net: phy: aquantia: add support for aqr115c") Signed-off-by: Abhishek Chauhan <quic_abchauha@quicinc.com> --- drivers/net/phy/aquantia/aquantia_main.c | 7 +++++++ 1 file changed, 7 insertions(+)