@@ -781,17 +781,6 @@ static int dp83822_of_init(struct phy_device *phydev)
struct device *dev = &phydev->mdio.dev;
const char *of_val;
- /* Signal detection for the PHY is only enabled if the FX_EN and the
- * SD_EN pins are strapped. Signal detection can only enabled if FX_EN
- * is strapped otherwise signal detection is disabled for the PHY.
- */
- if (dp83822->fx_enabled && dp83822->fx_sd_enable)
- dp83822->fx_signal_det_low = device_property_present(dev,
- "ti,link-loss-low");
- if (!dp83822->fx_enabled)
- dp83822->fx_enabled = device_property_present(dev,
- "ti,fiber-mode");
-
if (!device_property_read_string(dev, "ti,gpio2-clk-out", &of_val)) {
if (strcmp(of_val, "mac-if") == 0) {
dp83822->gpio2_clk_out = DP83822_CLK_SRC_MAC_IF;
@@ -884,6 +873,43 @@ static int dp83822_read_straps(struct phy_device *phydev)
return 0;
}
+static int dp83822_attach_port(struct phy_device *phydev, struct phy_port *port)
+{
+ struct dp83822_private *dp83822 = phydev->priv;
+ int ret;
+
+ if (port->mediums) {
+ if (phy_port_is_fiber(port) ||
+ port->mediums & BIT(ETHTOOL_LINK_MEDIUM_BASEX))
+ dp83822->fx_enabled = true;
+ } else {
+ ret = dp83822_read_straps(phydev);
+ if (ret)
+ return ret;
+
+#ifdef CONFIG_OF_MDIO
+ if (dp83822->fx_enabled && dp83822->fx_sd_enable)
+ dp83822->fx_signal_det_low =
+ device_property_present(dev, "ti,link-loss-low");
+ if (!dp83822->fx_enabled)
+ dp83822->fx_enabled =
+ device_property_present(dev, "ti,fiber-mode");
+#endif
+
+ if (dp83822->fx_enabled) {
+ port->lanes = 1;
+ port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASEF) |
+ BIT(ETHTOOL_LINK_MEDIUM_BASEX);
+ } else {
+ /* This PHY can only to 100BaseTX max, so on 2 lanes */
+ port->lanes = 2;
+ port->mediums = BIT(ETHTOOL_LINK_MEDIUM_BASET);
+ }
+ }
+
+ return 0;
+}
+
static int dp8382x_probe(struct phy_device *phydev)
{
struct dp83822_private *dp83822;
@@ -900,25 +926,13 @@ static int dp8382x_probe(struct phy_device *phydev)
static int dp83822_probe(struct phy_device *phydev)
{
- struct dp83822_private *dp83822;
int ret;
ret = dp8382x_probe(phydev);
if (ret)
return ret;
- dp83822 = phydev->priv;
-
- ret = dp83822_read_straps(phydev);
- if (ret)
- return ret;
-
- ret = dp83822_of_init(phydev);
- if (ret)
- return ret;
-
- if (dp83822->fx_enabled)
- phydev->port = PORT_FIBRE;
+ dp83822_of_init(phydev);
return 0;
}
@@ -1104,6 +1118,7 @@ static int dp83822_led_hw_control_get(struct phy_device *phydev, u8 index,
.led_hw_is_supported = dp83822_led_hw_is_supported, \
.led_hw_control_set = dp83822_led_hw_control_set, \
.led_hw_control_get = dp83822_led_hw_control_get, \
+ .attach_port = dp83822_attach_port \
}
#define DP83825_PHY_DRIVER(_id, _name) \
With the phy_port representation intrduced, we can use .attach_port to populate the port information based on either the straps or the ti,fiber-mode property. This allows simplifying the probe function and allow users to override the strapping configuration. Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com> --- RFC V2: Addressd a warning for an unused variable drivers/net/phy/dp83822.c | 63 ++++++++++++++++++++++++--------------- 1 file changed, 39 insertions(+), 24 deletions(-)