@@ -16,6 +16,10 @@ struct stmmac_pci_info {
static void loongson_default_data(struct pci_dev *pdev,
struct plat_stmmacenet_data *plat)
{
+ /* Get bus_id, this can be overloaded later */
+ plat->bus_id = (pci_domain_nr(pdev->bus) << 16) |
+ PCI_DEVID(pdev->bus->number, pdev->devfn);
+
plat->clk_csr = 2; /* clk_csr_i = 20-35MHz & MDC = clk_csr_i/16 */
plat->has_gmac = 1;
plat->force_sf_dma_mode = 1;
@@ -56,6 +60,9 @@ static int loongson_gmac_data(struct pci_dev *pdev,
plat->dma_cfg->pbl = 32;
plat->dma_cfg->pblx8 = true;
+ plat->clk_ref_rate = 125000000;
+ plat->clk_ptp_rate = 125000000;
+
return 0;
}
@@ -72,13 +79,6 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,
struct stmmac_resources res;
struct device_node *np;
- np = dev_of_node(&pdev->dev);
-
- if (!np) {
- pr_info("dwmac_loongson_pci: No OF node\n");
- return -ENODEV;
- }
-
plat = devm_kzalloc(&pdev->dev, sizeof(*plat), GFP_KERNEL);
if (!plat)
return -ENOMEM;
@@ -94,6 +94,7 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,
if (!plat->dma_cfg)
return -ENOMEM;
+ np = dev_of_node(&pdev->dev);
plat->mdio_node = of_get_child_by_name(np, "mdio");
if (plat->mdio_node) {
dev_info(&pdev->dev, "Found MDIO subnode\n");
@@ -125,42 +126,48 @@ static int loongson_dwmac_probe(struct pci_dev *pdev,
if (ret)
goto err_disable_device;
- bus_id = of_alias_get_id(np, "ethernet");
- if (bus_id >= 0)
- plat->bus_id = bus_id;
+ if (np) {
+ bus_id = of_alias_get_id(np, "ethernet");
+ if (bus_id >= 0)
+ plat->bus_id = bus_id;
- phy_mode = device_get_phy_mode(&pdev->dev);
- if (phy_mode < 0) {
- dev_err(&pdev->dev, "phy_mode not found\n");
- ret = phy_mode;
- goto err_disable_device;
+ phy_mode = device_get_phy_mode(&pdev->dev);
+ if (phy_mode < 0) {
+ dev_err(&pdev->dev, "phy_mode not found\n");
+ ret = phy_mode;
+ goto err_disable_device;
+ }
+ plat->phy_interface = phy_mode;
}
- plat->phy_interface = phy_mode;
pci_enable_msi(pdev);
memset(&res, 0, sizeof(res));
res.addr = pcim_iomap_table(pdev)[0];
-
- res.irq = of_irq_get_byname(np, "macirq");
- if (res.irq < 0) {
- dev_err(&pdev->dev, "IRQ macirq not found\n");
- ret = -ENODEV;
- goto err_disable_msi;
- }
-
- res.wol_irq = of_irq_get_byname(np, "eth_wake_irq");
- if (res.wol_irq < 0) {
- dev_info(&pdev->dev,
- "IRQ eth_wake_irq not found, using macirq\n");
- res.wol_irq = res.irq;
- }
-
- res.lpi_irq = of_irq_get_byname(np, "eth_lpi");
- if (res.lpi_irq < 0) {
- dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
- ret = -ENODEV;
- goto err_disable_msi;
+ if (np) {
+ res.irq = of_irq_get_byname(np, "macirq");
+ if (res.irq < 0) {
+ dev_err(&pdev->dev, "IRQ macirq not found\n");
+ ret = -ENODEV;
+ goto err_disable_msi;
+ }
+
+ res.wol_irq = of_irq_get_byname(np, "eth_wake_irq");
+ if (res.wol_irq < 0) {
+ dev_info(&pdev->dev,
+ "IRQ eth_wake_irq not found, using macirq\n");
+ res.wol_irq = res.irq;
+ }
+
+ res.lpi_irq = of_irq_get_byname(np, "eth_lpi");
+ if (res.lpi_irq < 0) {
+ dev_err(&pdev->dev, "IRQ eth_lpi not found\n");
+ ret = -ENODEV;
+ goto err_disable_msi;
+ }
+ } else {
+ res.irq = pdev->irq;
+ res.wol_irq = pdev->irq;
}
ret = stmmac_dvr_probe(&pdev->dev, plat, &res);
Current dwmac-loongson only support LS2K in the "probed with PCI and configured with DT" manner. Add LS7A support on which the devices are fully PCI (non-DT). Signed-off-by: Feiyang Chen <chenfeiyang@loongson.cn> --- .../ethernet/stmicro/stmmac/dwmac-loongson.c | 79 ++++++++++--------- 1 file changed, 43 insertions(+), 36 deletions(-)