@@ -357,11 +357,11 @@ create_vrf()
ip -netns ${ns} link set ${vrf} up
ip -netns ${ns} route add vrf ${vrf} unreachable default metric 8192
ip -netns ${ns} -6 route add vrf ${vrf} unreachable default metric 8192
ip -netns ${ns} addr add 127.0.0.1/8 dev ${vrf}
- ip -netns ${ns} -6 addr add ::1 dev ${vrf} nodad
+ ip -netns ${ns} -6 addr add ::1 dev ${vrf}
if [ "${addr}" != "-" ]; then
ip -netns ${ns} addr add dev ${vrf} ${addr}
fi
if [ "${addr6}" != "-" ]; then
ip -netns ${ns} -6 addr add dev ${vrf} ${addr6}
@@ -378,10 +378,11 @@ create_ns()
local ns=$1
local addr=$2
local addr6=$3
ip netns add ${ns}
+ ip netns exec ${ns} sysctl -wq net.ipv6.conf.{all,default}.accept_dad=0
ip -netns ${ns} link set lo up
if [ "${addr}" != "-" ]; then
ip -netns ${ns} addr add dev lo ${addr}
fi
@@ -490,12 +491,10 @@ setup()
# tell ns-B how to get to remote addresses of ns-A
ip -netns ${NSB} ro add ${NSA_LO_IP}/32 via ${NSA_IP} dev ${NSB_DEV}
ip -netns ${NSB} ro add ${NSA_LO_IP6}/128 via ${NSA_IP6} dev ${NSB_DEV}
set +e
-
- sleep 1
}
setup_lla_only()
{
# make sure we are starting with a clean slate
@@ -520,12 +519,10 @@ setup_lla_only()
create_vrf ${NSA} ${VRF} ${VRF_TABLE} "-" "-"
ip -netns ${NSA} link set dev ${NSA_DEV} vrf ${VRF}
ip -netns ${NSA} link set dev ${NSA_DEV2} vrf ${VRF}
set +e
-
- sleep 1
}
################################################################################
# IPv4
@@ -3014,11 +3011,11 @@ ipv6_udp_novrf()
sleep 1
run_cmd_nsb nettest -6 -D -r ${NSA_IP6}
log_test $? 0 "UDP in - LLA to GUA"
run_cmd_nsb ip -6 ro del ${NSA_IP6}/128 dev ${NSB_DEV}
- run_cmd_nsb ip -6 addr add ${NSB_IP6}/64 dev ${NSB_DEV} nodad
+ run_cmd_nsb ip -6 addr add ${NSB_IP6}/64 dev ${NSB_DEV}
}
ipv6_udp_vrf()
{
local a
@@ -3292,11 +3289,11 @@ ipv6_udp_vrf()
sleep 1
run_cmd_nsb nettest -6 -D -r ${NSA_IP6}
log_test $? 0 "UDP in - LLA to GUA"
run_cmd_nsb ip -6 ro del ${NSA_IP6}/128 dev ${NSB_DEV}
- run_cmd_nsb ip -6 addr add ${NSB_IP6}/64 dev ${NSB_DEV} nodad
+ run_cmd_nsb ip -6 addr add ${NSB_IP6}/64 dev ${NSB_DEV}
}
ipv6_udp()
{
# should not matter, but set to known state
@@ -3742,11 +3739,11 @@ use_case_br()
setup_cmd ip addr del dev ${NSA_DEV} ${NSA_IP}/24
setup_cmd ip -6 addr del dev ${NSA_DEV} ${NSA_IP6}/64
setup_cmd ip link add br0 type bridge
setup_cmd ip addr add dev br0 ${NSA_IP}/24
- setup_cmd ip -6 addr add dev br0 ${NSA_IP6}/64 nodad
+ setup_cmd ip -6 addr add dev br0 ${NSA_IP6}/64
setup_cmd ip li set ${NSA_DEV} master br0
setup_cmd ip li set ${NSA_DEV} up
setup_cmd ip li set br0 up
setup_cmd ip li set br0 vrf ${VRF}
@@ -3791,15 +3788,15 @@ use_case_br()
setup_cmd ip li set br0 nomaster
setup_cmd ip li add br0.100 link br0 type vlan id 100
setup_cmd ip li set br0.100 vrf ${VRF} up
setup_cmd ip addr add dev br0.100 172.16.101.1/24
- setup_cmd ip -6 addr add dev br0.100 2001:db8:101::1/64 nodad
+ setup_cmd ip -6 addr add dev br0.100 2001:db8:101::1/64
setup_cmd_nsb ip li add vlan100 link ${NSB_DEV} type vlan id 100
setup_cmd_nsb ip addr add dev vlan100 172.16.101.2/24
- setup_cmd_nsb ip -6 addr add dev vlan100 2001:db8:101::2/64 nodad
+ setup_cmd_nsb ip -6 addr add dev vlan100 2001:db8:101::2/64
setup_cmd_nsb ip li set vlan100 up
sleep 1
rmmod br_netfilter 2>/dev/null
Duplicate Address Detection makes ipv6 addresses unavailable for a short period after adding (average about 1 second). Adding sleep statements avoid this but since all addresses in the test environment are controlled from the same source we can just disable DAD for the entire namespace. Unlike sprinkling nodad to all ipv6 address additions this also skips DAD for link-local-addresses. Signed-off-by: Leonard Crestez <cdleonard@gmail.com> --- tools/testing/selftests/net/fcnal-test.sh | 17 +++++++---------- 1 file changed, 7 insertions(+), 10 deletions(-)