diff mbox series

[2/9] net: ethernet: mtk_eth_soc: set MDIO bus clock frequency

Message ID a613b66b4872b5f3f09544138d03d5326a8f6f8b.1675407169.git.daniel@makrotopia.org (mailing list archive)
State Superseded
Delegated to: Netdev Maintainers
Headers show
Series net: ethernet: mtk_eth_soc: various enhancements | expand

Checks

Context Check Description
netdev/tree_selection success Guessing tree name failed - patch did not apply

Commit Message

Daniel Golle Feb. 3, 2023, 7:01 a.m. UTC
Set MDIO bus clock frequency and allow setting a custom maximum
frequency from device tree.

Signed-off-by: Daniel Golle <daniel@makrotopia.org>
---
 drivers/net/ethernet/mediatek/mtk_eth_soc.c | 25 +++++++++++++++++++++
 drivers/net/ethernet/mediatek/mtk_eth_soc.h |  5 +++++
 2 files changed, 30 insertions(+)

Comments

Andrew Lunn Feb. 3, 2023, 2:06 p.m. UTC | #1
>  static int mtk_mdio_init(struct mtk_eth *eth)
>  {
>  	struct device_node *mii_np;
> +	int clk = 25000000, max_clk = 2500000, divider = 1;
>  	int ret;
> +	u32 val;

Reverse Christmas tree please.

> +
> +	if (!of_property_read_u32(mii_np, "clock-frequency", &val))
> +		max_clk = val;
> +
> +	while (clk / divider > max_clk) {
> +		if (divider >= 63)
> +			break;
> +
> +		divider++;
> +	};

Please add some range checks here. Return -EINVAL if val > max_clock.
Also, if divider = 63 indicating the requested clock is too slow.

> +
> +	val = mtk_r32(eth, MTK_PPSC);
> +	val |= PPSC_MDC_TURBO;
> +	mtk_w32(eth, val, MTK_PPSC);
> +
> +	/* Configure MDC Divider */
> +	val = mtk_r32(eth, MTK_PPSC);
> +	val &= ~PPSC_MDC_CFG;
> +	val |= FIELD_PREP(PPSC_MDC_CFG, divider);
> +	mtk_w32(eth, val, MTK_PPSC);

Can these two writes to MTK_PPSC be combined into one? 

val |= FIELD_PREP(PPSC_MDC_CFG, divider) | PPSC_MDC_TURBO;

    Andrew
Vladimir Oltean Feb. 3, 2023, 9:48 p.m. UTC | #2
On Fri, Feb 03, 2023 at 07:01:01AM +0000, Daniel Golle wrote:
> Set MDIO bus clock frequency and allow setting a custom maximum
> frequency from device tree.
> 
> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
> ---
>  drivers/net/ethernet/mediatek/mtk_eth_soc.c | 25 +++++++++++++++++++++
>  drivers/net/ethernet/mediatek/mtk_eth_soc.h |  5 +++++
>  2 files changed, 30 insertions(+)
> 
> diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
> index a44ffff48c7b..9050423821dc 100644
> --- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
> +++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
> @@ -790,7 +790,9 @@ static const struct phylink_mac_ops mtk_phylink_ops = {
>  static int mtk_mdio_init(struct mtk_eth *eth)
>  {
>  	struct device_node *mii_np;
> +	int clk = 25000000, max_clk = 2500000, divider = 1;

Would be good if constant values (clk) weren't put in variables.

>  	int ret;
> +	u32 val;
>  
>  	mii_np = of_get_child_by_name(eth->dev->of_node, "mdio-bus");
>  	if (!mii_np) {
> @@ -818,6 +820,29 @@ static int mtk_mdio_init(struct mtk_eth *eth)
>  	eth->mii_bus->parent = eth->dev;
>  
>  	snprintf(eth->mii_bus->id, MII_BUS_ID_SIZE, "%pOFn", mii_np);
> +
> +	if (!of_property_read_u32(mii_np, "clock-frequency", &val))
> +		max_clk = val;

Checking for valid range? There should also probably be a dt-bindings
patch for this.

> +
> +	while (clk / divider > max_clk) {
> +		if (divider >= 63)
> +			break;
> +
> +		divider++;
> +	};

uhm, "divider = min(DIV_ROUND_UP(25000000, max_clk), 63);"? I don't
think the compiler is smart enough to optimize away this loop.

> +
> +	val = mtk_r32(eth, MTK_PPSC);
> +	val |= PPSC_MDC_TURBO;
> +	mtk_w32(eth, val, MTK_PPSC);

What does "TURBO" do and why do you set it unconditionally?

> +
> +	/* Configure MDC Divider */
> +	val = mtk_r32(eth, MTK_PPSC);
> +	val &= ~PPSC_MDC_CFG;
> +	val |= FIELD_PREP(PPSC_MDC_CFG, divider);
> +	mtk_w32(eth, val, MTK_PPSC);
> +
> +	dev_dbg(eth->dev, "MDC is running on %d Hz\n", clk / divider);
> +
>  	ret = of_mdiobus_register(eth->mii_bus, mii_np);
>  
>  err_put_node:
> diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.h b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
> index 7230dcb29315..724815ae18a0 100644
> --- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h
> +++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
> @@ -363,6 +363,11 @@
>  #define RX_DMA_VTAG_V2		BIT(0)
>  #define RX_DMA_L4_VALID_V2	BIT(2)
>  
> +/* PHY Polling and SMI Master Control registers */
> +#define MTK_PPSC		0x10000
> +#define PPSC_MDC_CFG		GENMASK(29, 24)
> +#define PPSC_MDC_TURBO		BIT(20)
> +
>  /* PHY Indirect Access Control registers */
>  #define MTK_PHY_IAC		0x10004
>  #define PHY_IAC_ACCESS		BIT(31)
> -- 
> 2.39.1
>
Andrew Lunn Feb. 3, 2023, 10:15 p.m. UTC | #3
> Checking for valid range? There should also probably be a dt-bindings
> patch for this.

This is a common mdio property in mdio.yaml. So there should not be
any need for a driver specific dt-binding.

    Andrew
Vladimir Oltean Feb. 3, 2023, 10:26 p.m. UTC | #4
On Fri, Feb 03, 2023 at 11:15:15PM +0100, Andrew Lunn wrote:
> > Checking for valid range? There should also probably be a dt-bindings
> > patch for this.
> 
> This is a common mdio property in mdio.yaml. So there should not be
> any need for a driver specific dt-binding.

I meant it would probably be informative if the dt schema for this MDIO
controller had a "default: $val", "minimum: $val" and "maximum: $val".
diff mbox series

Patch

diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.c b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
index a44ffff48c7b..9050423821dc 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.c
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.c
@@ -790,7 +790,9 @@  static const struct phylink_mac_ops mtk_phylink_ops = {
 static int mtk_mdio_init(struct mtk_eth *eth)
 {
 	struct device_node *mii_np;
+	int clk = 25000000, max_clk = 2500000, divider = 1;
 	int ret;
+	u32 val;
 
 	mii_np = of_get_child_by_name(eth->dev->of_node, "mdio-bus");
 	if (!mii_np) {
@@ -818,6 +820,29 @@  static int mtk_mdio_init(struct mtk_eth *eth)
 	eth->mii_bus->parent = eth->dev;
 
 	snprintf(eth->mii_bus->id, MII_BUS_ID_SIZE, "%pOFn", mii_np);
+
+	if (!of_property_read_u32(mii_np, "clock-frequency", &val))
+		max_clk = val;
+
+	while (clk / divider > max_clk) {
+		if (divider >= 63)
+			break;
+
+		divider++;
+	};
+
+	val = mtk_r32(eth, MTK_PPSC);
+	val |= PPSC_MDC_TURBO;
+	mtk_w32(eth, val, MTK_PPSC);
+
+	/* Configure MDC Divider */
+	val = mtk_r32(eth, MTK_PPSC);
+	val &= ~PPSC_MDC_CFG;
+	val |= FIELD_PREP(PPSC_MDC_CFG, divider);
+	mtk_w32(eth, val, MTK_PPSC);
+
+	dev_dbg(eth->dev, "MDC is running on %d Hz\n", clk / divider);
+
 	ret = of_mdiobus_register(eth->mii_bus, mii_np);
 
 err_put_node:
diff --git a/drivers/net/ethernet/mediatek/mtk_eth_soc.h b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
index 7230dcb29315..724815ae18a0 100644
--- a/drivers/net/ethernet/mediatek/mtk_eth_soc.h
+++ b/drivers/net/ethernet/mediatek/mtk_eth_soc.h
@@ -363,6 +363,11 @@ 
 #define RX_DMA_VTAG_V2		BIT(0)
 #define RX_DMA_L4_VALID_V2	BIT(2)
 
+/* PHY Polling and SMI Master Control registers */
+#define MTK_PPSC		0x10000
+#define PPSC_MDC_CFG		GENMASK(29, 24)
+#define PPSC_MDC_TURBO		BIT(20)
+
 /* PHY Indirect Access Control registers */
 #define MTK_PHY_IAC		0x10004
 #define PHY_IAC_ACCESS		BIT(31)