@@ -1687,6 +1687,136 @@ to control PoDL PSE Admin functions. This option is implementing
``IEEE 802.3-2018`` 30.15.1.2.1 acPoDLPSEAdminControl. See
``ETHTOOL_A_PODL_PSE_ADMIN_STATE`` for supported values.
+PLCA_GET_CFG
+============
+
+Gets PLCA RS attributes.
+
+Request contents:
+
+ ===================================== ====== ==========================
+ ``ETHTOOL_A_PLCA_HEADER`` nested request header
+ ===================================== ====== ==========================
+
+Kernel response contents:
+
+ ====================================== ====== =============================
+ ``ETHTOOL_A_PLCA_HEADER`` nested reply header
+ ``ETHTOOL_A_PLCA_VERSION`` u16 Supported PLCA management
+ interface standard/version
+ ``ETHTOOL_A_PLCA_ENABLED`` u8 PLCA Admin State
+ ``ETHTOOL_A_PLCA_NODE_ID`` u8 PLCA unique local node ID
+ ``ETHTOOL_A_PLCA_NODE_CNT`` u8 Number of PLCA nodes on the
+ netkork, including the
+ coordinator
+ ``ETHTOOL_A_PLCA_TO_TMR`` u8 Transmit Opportunity Timer
+ value in bit-times (BT)
+ ``ETHTOOL_A_PLCA_BURST_CNT`` u8 Number of additional packets
+ the node is allowed to send
+ within a single TO
+ ``ETHTOOL_A_PLCA_BURST_TMR`` u8 Time to wait for the MAC to
+ transmit a new frame before
+ terminating the burst
+ ====================================== ====== =============================
+
+When set, the optional ``ETHTOOL_A_PLCA_VERSION`` attribute indicates which
+standard and version the PLCA management interface complies to. When not set,
+the interface is vendor-specific and (possibly) supplied by the driver.
+The OPEN Alliance SIG specifies a standard register map for 10BASE-T1S PHYs
+embedding the PLCA Reconcialiation Sublayer. See "10BASE-T1S PLCA Management
+Registers" at https://www.opensig.org/about/specifications/. When this standard
+is supported, ETHTOOL_A_PLCA_VERSION is reported as 0Axx where 'xx' denotes the
+map version (see Table A.1.0 — IDVER bits assignment).
+
+When set, the optional ``ETHTOOL_A_PLCA_ENABLED`` attribute indicates the
+administrative state of the PLCA RS. When not set, the node operates in "plain"
+CSMA/CD mode. This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.1
+aPLCAAdminState / 30.16.1.2.1 acPLCAAdminControl.
+
+When set, the optional ``ETHTOOL_A_PLCA_NODE_ID`` attribute indicates the
+configured local node ID of the PHY. This ID determines which transmit
+opportunity (TO) is reseverd for the node to transmit into. This option is
+corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.4 aPLCALocalNodeID.
+
+When set, the optional ``ETHTOOL_A_PLCA_NODE_CNT`` attribute indicates the
+configured maximum number of PLCA nodes on the mixing-segment. This number
+determines the total number of transmit opportunities generated during a
+PLCA cycle. This attribute is relevant only for the PLCA coordinator, which is
+the node with aPLCALocalNodeID set to 0. Follower nodes ignore this setting.
+This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.3
+aPLCANodeCount.
+
+When set, the optional ``ETHTOOL_A_PLCA_TO_TMR`` attribute indicates the
+configured value of the transmit opportunity timer in bit-times. This value
+must be set equal across all nodes sharing the medium for PLCA to work
+correctly. This option is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.5
+aPLCATransmitOpportunityTimer.
+
+When set, the optional ``ETHTOOL_A_PLCA_BURST_CNT`` attribute indicates the
+configured number of extra packets that the node is allowed to send during a
+single transmit opportunity. By default, this attribute is 0, meaning that
+the node can only send a sigle frame per TO. When greater than 0, the PLCA RS
+keeps the TO after any transmission, waiting for the MAC to send a new frame
+for up to aPLCABurstTimer BTs. This can only happen a number of times per PLCA
+cycle up to the value of this parameter. After that, the burst is over and the
+normal counting of TOs resumes. This option is corresponding to
+``IEEE 802.3cg-2019`` 30.16.1.1.6 aPLCAMaxBurstCount.
+
+When set, the optional ``ETHTOOL_A_PLCA_BURST_TMR`` attribute indicates how
+many bit-times the PLCA RS waits for the MAC to initiate a new transmission
+when aPLCAMaxBurstCount is greater than 0. If the MAC fails to send a new
+frame within this time, the burst ends and the counting of TOs resumes.
+Otherwise, the new frame is sent as part of the current burst. This option
+is corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.7 aPLCABurstTimer.
+
+PLCA_SET_CFG
+============
+
+Sets PLCA RS parameters.
+
+Request contents:
+
+ ====================================== ====== =============================
+ ``ETHTOOL_A_PLCA_HEADER`` nested request header
+ ``ETHTOOL_A_PLCA_ENABLED`` u8 PLCA Admin State
+ ``ETHTOOL_A_PLCA_NODE_ID`` u8 PLCA unique local node ID
+ ``ETHTOOL_A_PLCA_NODE_CNT`` u8 Number of PLCA nodes on the
+ netkork, including the
+ coordinator
+ ``ETHTOOL_A_PLCA_TO_TMR`` u8 Transmit Opportunity Timer
+ value in bit-times (BT)
+ ``ETHTOOL_A_PLCA_BURST_CNT`` u8 Number of additional packets
+ the node is allowed to send
+ within a single TO
+ ``ETHTOOL_A_PLCA_BURST_TMR`` u8 Time to wait for the MAC to
+ transmit a new frame before
+ terminating the burst
+ ====================================== ====== =============================
+
+For a description of each attribute, see ``PLCA_GET_CFG``.
+
+PLCA_GET_STATUS
+===============
+
+Gets PLCA RS status information.
+
+Request contents:
+
+ ===================================== ====== ==========================
+ ``ETHTOOL_A_PLCA_HEADER`` nested request header
+ ===================================== ====== ==========================
+
+Kernel response contents:
+
+ ====================================== ====== =============================
+ ``ETHTOOL_A_PLCA_HEADER`` nested reply header
+ ``ETHTOOL_A_PLCA_STATUS`` u8 PLCA RS operational status
+ ====================================== ====== =============================
+
+When set, the ``ETHTOOL_A_PLCA_STATUS`` attribute indicates whether the node is
+detecting the presence of the BEACON on the network. This flag is
+corresponding to ``IEEE 802.3cg-2019`` 30.16.1.1.2 aPLCAStatus.
+
Request translation
===================
@@ -1788,4 +1918,7 @@ are netlink only.
n/a ``ETHTOOL_MSG_PHC_VCLOCKS_GET``
n/a ``ETHTOOL_MSG_MODULE_GET``
n/a ``ETHTOOL_MSG_MODULE_SET``
+ n/a ``ETHTOOL_MSG_PLCA_GET_CFG``
+ n/a ``ETHTOOL_MSG_PLCA_SET_CFG``
+ n/a ``ETHTOOL_MSG_PLCA_GET_STATUS``
=================================== =====================================
@@ -13,7 +13,7 @@
*/
const char *phy_speed_to_str(int speed)
{
- BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 99,
+ BUILD_BUG_ON_MSG(__ETHTOOL_LINK_MODE_MASK_NBITS != 102,
"Enum ethtool_link_mode_bit_indices and phylib are out of sync. "
"If a speed or mode has been added please update phy_speed_to_str "
"and the PHY settings array.\n");
@@ -260,6 +260,9 @@ static const struct phy_setting settings[] = {
PHY_SETTING( 10, FULL, 10baseT_Full ),
PHY_SETTING( 10, HALF, 10baseT_Half ),
PHY_SETTING( 10, FULL, 10baseT1L_Full ),
+ PHY_SETTING( 10, FULL, 10baseT1S_Full ),
+ PHY_SETTING( 10, HALF, 10baseT1S_Half ),
+ PHY_SETTING( 10, HALF, 10baseT1S_P2MP_Half ),
};
#undef PHY_SETTING
@@ -241,12 +241,16 @@ void phylink_caps_to_linkmodes(unsigned long *linkmodes, unsigned long caps)
if (caps & MAC_ASYM_PAUSE)
__set_bit(ETHTOOL_LINK_MODE_Asym_Pause_BIT, linkmodes);
- if (caps & MAC_10HD)
+ if (caps & MAC_10HD) {
__set_bit(ETHTOOL_LINK_MODE_10baseT_Half_BIT, linkmodes);
+ __set_bit(ETHTOOL_LINK_MODE_10baseT1S_Half_BIT, linkmodes);
+ __set_bit(ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT, linkmodes);
+ }
if (caps & MAC_10FD) {
__set_bit(ETHTOOL_LINK_MODE_10baseT_Full_BIT, linkmodes);
__set_bit(ETHTOOL_LINK_MODE_10baseT1L_Full_BIT, linkmodes);
+ __set_bit(ETHTOOL_LINK_MODE_10baseT1S_Full_BIT, linkmodes);
}
if (caps & MAC_100HD) {
@@ -1741,6 +1741,9 @@ enum ethtool_link_mode_bit_indices {
ETHTOOL_LINK_MODE_800000baseDR8_2_Full_BIT = 96,
ETHTOOL_LINK_MODE_800000baseSR8_Full_BIT = 97,
ETHTOOL_LINK_MODE_800000baseVR8_Full_BIT = 98,
+ ETHTOOL_LINK_MODE_10baseT1S_Full_BIT = 99,
+ ETHTOOL_LINK_MODE_10baseT1S_Half_BIT = 100,
+ ETHTOOL_LINK_MODE_10baseT1S_P2MP_Half_BIT = 101,
/* must be last entry */
__ETHTOOL_LINK_MODE_MASK_NBITS
@@ -208,6 +208,9 @@ const char link_mode_names[][ETH_GSTRING_LEN] = {
__DEFINE_LINK_MODE_NAME(800000, DR8_2, Full),
__DEFINE_LINK_MODE_NAME(800000, SR8, Full),
__DEFINE_LINK_MODE_NAME(800000, VR8, Full),
+ __DEFINE_LINK_MODE_NAME(10, T1S, Full),
+ __DEFINE_LINK_MODE_NAME(10, T1S, Half),
+ __DEFINE_LINK_MODE_NAME(10, T1S_P2MP, Half),
};
static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
@@ -244,6 +247,8 @@ static_assert(ARRAY_SIZE(link_mode_names) == __ETHTOOL_LINK_MODE_MASK_NBITS);
#define __LINK_MODE_LANES_X 1
#define __LINK_MODE_LANES_FX 1
#define __LINK_MODE_LANES_T1L 1
+#define __LINK_MODE_LANES_T1S 1
+#define __LINK_MODE_LANES_T1S_P2MP 1
#define __LINK_MODE_LANES_VR8 8
#define __LINK_MODE_LANES_DR8_2 8
@@ -366,6 +371,9 @@ const struct link_mode_info link_mode_params[] = {
__DEFINE_LINK_MODE_PARAMS(800000, DR8_2, Full),
__DEFINE_LINK_MODE_PARAMS(800000, SR8, Full),
__DEFINE_LINK_MODE_PARAMS(800000, VR8, Full),
+ __DEFINE_LINK_MODE_PARAMS(10, T1S, Full),
+ __DEFINE_LINK_MODE_PARAMS(10, T1S, Half),
+ __DEFINE_LINK_MODE_PARAMS(10, T1S_P2MP, Half),
};
static_assert(ARRAY_SIZE(link_mode_params) == __ETHTOOL_LINK_MODE_MASK_NBITS);
This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S Ethernet PHY. According to the specifications, the 10BASE-T1S supports Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or Point-To-Multipoint (AKA Multi-Drop) Hal-Duplex operations. Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com> --- Documentation/networking/ethtool-netlink.rst | 133 +++++++++++++++++++ drivers/net/phy/phy-core.c | 5 +- drivers/net/phy/phylink.c | 6 +- include/uapi/linux/ethtool.h | 3 + net/ethtool/common.c | 8 ++ 5 files changed, 153 insertions(+), 2 deletions(-)