diff mbox series

[1/2] riscv: virt: Fix pcie memory ranges

Message ID 1542754831-25567-1-git-send-email-linux@roeck-us.net (mailing list archive)
State New, archived
Headers show
Series [1/2] riscv: virt: Fix pcie memory ranges | expand

Commit Message

Guenter Roeck Nov. 20, 2018, 11 p.m. UTC
- Provide separate maps for VIRT_PCIE_MMIO (32 bit) and
  VIRT_PCIE_MMIO_HIGH (64 bit)
- VIRT_PCIE_PIO is for IO ports, not for the physical address
- VIRT_PCIE_ECAM size reduced to size needed to cover 256 ports
- Use memmap[VIRT_PCIE_ECAM].size instead of memmap[VIRT_PCIE_ECAM].base
  to calculate the bus number range
- Use qemu_fdt_setprop_sized_cells() to create reg and ranges entries
- Fix parameters for gpex_pcie_init()
  (ECAM and MMIO addresses were swapped)

Signed-off-by: Guenter Roeck <linux@roeck-us.net>
---
This series applies on top of 
	https://patchwork.kernel.org/cover/10661699/

Tested with mmc:
    qemu-system-riscv64 -M virt -m 512M -no-reboot \
	-bios riscv64/bbl -kernel vmlinux \
	-netdev user,id=net0 -device virtio-net-device,netdev=net0 \
	-snapshot -device sdhci-pci -device sd-card,drive=d0 \
	-drive file=rootfs.ext2,format=raw,if=none,id=d0 \
	-append 'root=/dev/mmcblk0 rw rootwait panic=-1 console=ttyS0,115200' \
	-nographic -monitor none

and nvme:
    qemu-system-riscv64 -M virt -m 512M -no-reboot \
	-bios riscv64/bbl -kernel vmlinux \
	-netdev user,id=net0 -device virtio-net-device,netdev=net0 \
	-snapshot -device nvme,serial=foo,drive=d0 \
	-drive file=rootfs.ext2,if=none,format=raw,id=d0 \
	-append 'root=/dev/nvme0n1 rw rootwait panic=-1 console=ttyS0,115200' \
	-nographic -monitor none

 hw/riscv/virt.c         | 51 ++++++++++++++++++++++++++++++++-----------------
 include/hw/riscv/virt.h |  1 +
 2 files changed, 35 insertions(+), 17 deletions(-)

Comments

Alistair Francis Nov. 21, 2018, 12:43 a.m. UTC | #1
On Tue, Nov 20, 2018 at 3:01 PM Guenter Roeck <linux@roeck-us.net> wrote:
>
> - Provide separate maps for VIRT_PCIE_MMIO (32 bit) and
>   VIRT_PCIE_MMIO_HIGH (64 bit)
> - VIRT_PCIE_PIO is for IO ports, not for the physical address
> - VIRT_PCIE_ECAM size reduced to size needed to cover 256 ports
> - Use memmap[VIRT_PCIE_ECAM].size instead of memmap[VIRT_PCIE_ECAM].base
>   to calculate the bus number range
> - Use qemu_fdt_setprop_sized_cells() to create reg and ranges entries
> - Fix parameters for gpex_pcie_init()
>   (ECAM and MMIO addresses were swapped)
>
> Signed-off-by: Guenter Roeck <linux@roeck-us.net>

Hey Gunter,

Thanks for the patch! This was causing me all kinds of headaches.
Unfortunately I had managed to figure out the memory addresses thanks
to Bin Meng's help.

You can see the new tree here:
https://github.com/alistair23/qemu/tree/mainline/alistair/sifive_pcie.next

If you have anything you wan to add to that branch just let me know.

Alistair

> ---
> This series applies on top of
>         https://patchwork.kernel.org/cover/10661699/
>
> Tested with mmc:
>     qemu-system-riscv64 -M virt -m 512M -no-reboot \
>         -bios riscv64/bbl -kernel vmlinux \
>         -netdev user,id=net0 -device virtio-net-device,netdev=net0 \
>         -snapshot -device sdhci-pci -device sd-card,drive=d0 \
>         -drive file=rootfs.ext2,format=raw,if=none,id=d0 \
>         -append 'root=/dev/mmcblk0 rw rootwait panic=-1 console=ttyS0,115200' \
>         -nographic -monitor none
>
> and nvme:
>     qemu-system-riscv64 -M virt -m 512M -no-reboot \
>         -bios riscv64/bbl -kernel vmlinux \
>         -netdev user,id=net0 -device virtio-net-device,netdev=net0 \
>         -snapshot -device nvme,serial=foo,drive=d0 \
>         -drive file=rootfs.ext2,if=none,format=raw,id=d0 \
>         -append 'root=/dev/nvme0n1 rw rootwait panic=-1 console=ttyS0,115200' \
>         -nographic -monitor none
>
>  hw/riscv/virt.c         | 51 ++++++++++++++++++++++++++++++++-----------------
>  include/hw/riscv/virt.h |  1 +
>  2 files changed, 35 insertions(+), 17 deletions(-)
>
> diff --git a/hw/riscv/virt.c b/hw/riscv/virt.c
> index 1aac5ca..675899d 100644
> --- a/hw/riscv/virt.c
> +++ b/hw/riscv/virt.c
> @@ -59,10 +59,10 @@ static const struct MemmapEntry {
>      [VIRT_UART0] =    { 0x10000000,      0x100 },
>      [VIRT_VIRTIO] =   { 0x10001000,     0x1000 },
>      [VIRT_DRAM] =     { 0x80000000,        0x0 },
> -    [VIRT_PCIE_MMIO] = { 0x2000000000, 0x4000000 },
> -    [VIRT_PCIE_PIO] = { 0x2010000, 0x40000000 },
> -    [VIRT_PCIE_ECAM] = { 0x40000000, 0x20000000 },
> -
> +    [VIRT_PCIE_MMIO] = { 0x40000000, 0x40000000 },
> +    [VIRT_PCIE_MMIO_HIGH] = { 0x2000000000, 0x4000000000 },
> +    [VIRT_PCIE_PIO] =  { 0x10002000,     0x1000 },
> +    [VIRT_PCIE_ECAM] = { 0x30000000, 0x10000000 },
>  };
>
>  #define INTERREUPT_MAP_WIDTH 7
> @@ -231,8 +231,7 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
>          g_free(nodename);
>      }
>
> -    nodename = g_strdup_printf("/pci@%lx",
> -        (long) memmap[VIRT_PCIE_MMIO].base);
> +    nodename = g_strdup_printf("/pcie@%" PRIx64, memmap[VIRT_PCIE_MMIO].base);
>      qemu_fdt_add_subnode(fdt, nodename);
>      qemu_fdt_setprop_cells(fdt, nodename, "#address-cells", 0x3);
>      qemu_fdt_setprop_cells(fdt, nodename, "#interrupt-cells", 0x1);
> @@ -242,16 +241,26 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
>      qemu_fdt_setprop_string(fdt, nodename, "device_type", "pci");
>      qemu_fdt_setprop_cell(fdt, nodename, "linux,pci-domain", 0);
>      qemu_fdt_setprop_cells(fdt, nodename, "bus-range", 0,
> -                           memmap[VIRT_PCIE_ECAM].base /
> +                           memmap[VIRT_PCIE_ECAM].size /
>                                 PCIE_MMCFG_SIZE_MIN - 1);
>      qemu_fdt_setprop(fdt, nodename, "dma-coherent", NULL, 0);
> -    qemu_fdt_setprop_cells(fdt, nodename, "reg", 0x20, 0,
> -                           0, memmap[VIRT_PCIE_ECAM].size);
> -    qemu_fdt_setprop_cells(fdt, nodename, "ranges",
> -                           memmap[VIRT_PCIE_PIO].base,
> -                               0, memmap[VIRT_PCIE_PIO].size,
> -                           0, memmap[VIRT_PCIE_MMIO].base,
> -                               0, memmap[VIRT_PCIE_MMIO].size);
> +    qemu_fdt_setprop_sized_cells(fdt, nodename, "reg",
> +                                 2, memmap[VIRT_PCIE_ECAM].base,
> +                                 2, memmap[VIRT_PCIE_ECAM].size);
> +
> +    qemu_fdt_setprop_sized_cells(fdt, nodename, "ranges",
> +                                 1, FDT_PCI_RANGE_IOPORT, 2, 0,
> +                                 2, memmap[VIRT_PCIE_PIO].base,
> +                                 2, memmap[VIRT_PCIE_PIO].size,
> +                                 1, FDT_PCI_RANGE_MMIO,
> +                                 2, memmap[VIRT_PCIE_MMIO].base,
> +                                 2, memmap[VIRT_PCIE_MMIO].base,
> +                                 2, memmap[VIRT_PCIE_MMIO].size,
> +                                 1, FDT_PCI_RANGE_MMIO_64BIT,
> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].size);
> +
>      qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
>      qemu_fdt_setprop_cells(fdt, nodename, "interrupts", PCIE_IRQ);
>      create_pcie_irq_map(fdt, nodename, plic_phandle);
> @@ -289,12 +298,13 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
>  static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
>                                            hwaddr ecam_base, hwaddr ecam_size,
>                                            hwaddr mmio_base, hwaddr mmio_size,
> +                                          hwaddr mmio_hbase, hwaddr mmio_hsize,
>                                            hwaddr pio_base,
>                                            DeviceState *plic, bool link_up)
>  {
>      DeviceState *dev;
>      MemoryRegion *ecam_alias, *ecam_reg;
> -    MemoryRegion *mmio_alias, *mmio_reg;
> +    MemoryRegion *mmio_alias, *mmio_halias, *mmio_reg;
>      qemu_irq irq;
>      int i;
>
> @@ -314,6 +324,11 @@ static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
>                               mmio_reg, mmio_base, mmio_size);
>      memory_region_add_subregion(get_system_memory(), mmio_base, mmio_alias);
>
> +    mmio_halias = g_new0(MemoryRegion, 1);
> +    memory_region_init_alias(mmio_halias, OBJECT(dev), "pcie-mmio-high",
> +                             mmio_reg, mmio_hbase, mmio_hsize);
> +    memory_region_add_subregion(get_system_memory(), mmio_hbase, mmio_halias);
> +
>      sysbus_mmio_map(SYS_BUS_DEVICE(dev), 2, pio_base);
>
>      for (i = 0; i < GPEX_NUM_IRQS; i++) {
> @@ -444,10 +459,12 @@ static void riscv_virt_board_init(MachineState *machine)
>      }
>
>      dev = gpex_pcie_init(system_memory,
> -                         memmap[VIRT_PCIE_MMIO].base,
> -                         memmap[VIRT_PCIE_MMIO].size,
>                           memmap[VIRT_PCIE_ECAM].base,
>                           memmap[VIRT_PCIE_ECAM].size,
> +                         memmap[VIRT_PCIE_MMIO].base,
> +                         memmap[VIRT_PCIE_MMIO].size,
> +                         memmap[VIRT_PCIE_MMIO_HIGH].base,
> +                         memmap[VIRT_PCIE_MMIO_HIGH].size,
>                           memmap[VIRT_PCIE_PIO].base,
>                           DEVICE(s->plic), true);
>      pci_bus = PCI_HOST_BRIDGE(dev)->bus;
> diff --git a/include/hw/riscv/virt.h b/include/hw/riscv/virt.h
> index dd4fedd..99caf09 100644
> --- a/include/hw/riscv/virt.h
> +++ b/include/hw/riscv/virt.h
> @@ -40,6 +40,7 @@ enum {
>      VIRT_VIRTIO,
>      VIRT_DRAM,
>      VIRT_PCIE_MMIO,
> +    VIRT_PCIE_MMIO_HIGH,
>      VIRT_PCIE_PIO,
>      VIRT_PCIE_ECAM
>  };
> --
> 2.7.4
>
>
Guenter Roeck Nov. 21, 2018, 1:54 a.m. UTC | #2
Hi Alistair,

On 11/20/18 4:43 PM, Alistair Francis wrote:
> On Tue, Nov 20, 2018 at 3:01 PM Guenter Roeck <linux@roeck-us.net> wrote:
>>
>> - Provide separate maps for VIRT_PCIE_MMIO (32 bit) and
>>    VIRT_PCIE_MMIO_HIGH (64 bit)
>> - VIRT_PCIE_PIO is for IO ports, not for the physical address
>> - VIRT_PCIE_ECAM size reduced to size needed to cover 256 ports
>> - Use memmap[VIRT_PCIE_ECAM].size instead of memmap[VIRT_PCIE_ECAM].base
>>    to calculate the bus number range
>> - Use qemu_fdt_setprop_sized_cells() to create reg and ranges entries
>> - Fix parameters for gpex_pcie_init()
>>    (ECAM and MMIO addresses were swapped)
>>
>> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
> 
> Hey Gunter,
> 
> Thanks for the patch! This was causing me all kinds of headaches.
> Unfortunately I had managed to figure out the memory addresses thanks
> to Bin Meng's help.
> 
No worries. I am not married to this series. I'll give your tree a try,
hopefully tonight.

> You can see the new tree here:
> https://github.com/alistair23/qemu/tree/mainline/alistair/sifive_pcie.next
> 
> If you have anything you wan to add to that branch just let me know.
> 

One possible addition might be a 64 bit address range. I don't know
if that is needed for some pcie devices. I do see that nvme instantiates
from the 64 bit region, but I don't know if that is mandatory or just the
preference.

I would also suggest to add "include usb.mak" to the defconfig file. With this,
it is possible to support the full range of usb devices. I am using it for
various boot tests.

Thanks,
Guenter

> Alistair
> 
>> ---
>> This series applies on top of
>>          https://patchwork.kernel.org/cover/10661699/
>>
>> Tested with mmc:
>>      qemu-system-riscv64 -M virt -m 512M -no-reboot \
>>          -bios riscv64/bbl -kernel vmlinux \
>>          -netdev user,id=net0 -device virtio-net-device,netdev=net0 \
>>          -snapshot -device sdhci-pci -device sd-card,drive=d0 \
>>          -drive file=rootfs.ext2,format=raw,if=none,id=d0 \
>>          -append 'root=/dev/mmcblk0 rw rootwait panic=-1 console=ttyS0,115200' \
>>          -nographic -monitor none
>>
>> and nvme:
>>      qemu-system-riscv64 -M virt -m 512M -no-reboot \
>>          -bios riscv64/bbl -kernel vmlinux \
>>          -netdev user,id=net0 -device virtio-net-device,netdev=net0 \
>>          -snapshot -device nvme,serial=foo,drive=d0 \
>>          -drive file=rootfs.ext2,if=none,format=raw,id=d0 \
>>          -append 'root=/dev/nvme0n1 rw rootwait panic=-1 console=ttyS0,115200' \
>>          -nographic -monitor none
>>
>>   hw/riscv/virt.c         | 51 ++++++++++++++++++++++++++++++++-----------------
>>   include/hw/riscv/virt.h |  1 +
>>   2 files changed, 35 insertions(+), 17 deletions(-)
>>
>> diff --git a/hw/riscv/virt.c b/hw/riscv/virt.c
>> index 1aac5ca..675899d 100644
>> --- a/hw/riscv/virt.c
>> +++ b/hw/riscv/virt.c
>> @@ -59,10 +59,10 @@ static const struct MemmapEntry {
>>       [VIRT_UART0] =    { 0x10000000,      0x100 },
>>       [VIRT_VIRTIO] =   { 0x10001000,     0x1000 },
>>       [VIRT_DRAM] =     { 0x80000000,        0x0 },
>> -    [VIRT_PCIE_MMIO] = { 0x2000000000, 0x4000000 },
>> -    [VIRT_PCIE_PIO] = { 0x2010000, 0x40000000 },
>> -    [VIRT_PCIE_ECAM] = { 0x40000000, 0x20000000 },
>> -
>> +    [VIRT_PCIE_MMIO] = { 0x40000000, 0x40000000 },
>> +    [VIRT_PCIE_MMIO_HIGH] = { 0x2000000000, 0x4000000000 },
>> +    [VIRT_PCIE_PIO] =  { 0x10002000,     0x1000 },
>> +    [VIRT_PCIE_ECAM] = { 0x30000000, 0x10000000 },
>>   };
>>
>>   #define INTERREUPT_MAP_WIDTH 7
>> @@ -231,8 +231,7 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
>>           g_free(nodename);
>>       }
>>
>> -    nodename = g_strdup_printf("/pci@%lx",
>> -        (long) memmap[VIRT_PCIE_MMIO].base);
>> +    nodename = g_strdup_printf("/pcie@%" PRIx64, memmap[VIRT_PCIE_MMIO].base);
>>       qemu_fdt_add_subnode(fdt, nodename);
>>       qemu_fdt_setprop_cells(fdt, nodename, "#address-cells", 0x3);
>>       qemu_fdt_setprop_cells(fdt, nodename, "#interrupt-cells", 0x1);
>> @@ -242,16 +241,26 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
>>       qemu_fdt_setprop_string(fdt, nodename, "device_type", "pci");
>>       qemu_fdt_setprop_cell(fdt, nodename, "linux,pci-domain", 0);
>>       qemu_fdt_setprop_cells(fdt, nodename, "bus-range", 0,
>> -                           memmap[VIRT_PCIE_ECAM].base /
>> +                           memmap[VIRT_PCIE_ECAM].size /
>>                                  PCIE_MMCFG_SIZE_MIN - 1);
>>       qemu_fdt_setprop(fdt, nodename, "dma-coherent", NULL, 0);
>> -    qemu_fdt_setprop_cells(fdt, nodename, "reg", 0x20, 0,
>> -                           0, memmap[VIRT_PCIE_ECAM].size);
>> -    qemu_fdt_setprop_cells(fdt, nodename, "ranges",
>> -                           memmap[VIRT_PCIE_PIO].base,
>> -                               0, memmap[VIRT_PCIE_PIO].size,
>> -                           0, memmap[VIRT_PCIE_MMIO].base,
>> -                               0, memmap[VIRT_PCIE_MMIO].size);
>> +    qemu_fdt_setprop_sized_cells(fdt, nodename, "reg",
>> +                                 2, memmap[VIRT_PCIE_ECAM].base,
>> +                                 2, memmap[VIRT_PCIE_ECAM].size);
>> +
>> +    qemu_fdt_setprop_sized_cells(fdt, nodename, "ranges",
>> +                                 1, FDT_PCI_RANGE_IOPORT, 2, 0,
>> +                                 2, memmap[VIRT_PCIE_PIO].base,
>> +                                 2, memmap[VIRT_PCIE_PIO].size,
>> +                                 1, FDT_PCI_RANGE_MMIO,
>> +                                 2, memmap[VIRT_PCIE_MMIO].base,
>> +                                 2, memmap[VIRT_PCIE_MMIO].base,
>> +                                 2, memmap[VIRT_PCIE_MMIO].size,
>> +                                 1, FDT_PCI_RANGE_MMIO_64BIT,
>> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
>> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
>> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].size);
>> +
>>       qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
>>       qemu_fdt_setprop_cells(fdt, nodename, "interrupts", PCIE_IRQ);
>>       create_pcie_irq_map(fdt, nodename, plic_phandle);
>> @@ -289,12 +298,13 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
>>   static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
>>                                             hwaddr ecam_base, hwaddr ecam_size,
>>                                             hwaddr mmio_base, hwaddr mmio_size,
>> +                                          hwaddr mmio_hbase, hwaddr mmio_hsize,
>>                                             hwaddr pio_base,
>>                                             DeviceState *plic, bool link_up)
>>   {
>>       DeviceState *dev;
>>       MemoryRegion *ecam_alias, *ecam_reg;
>> -    MemoryRegion *mmio_alias, *mmio_reg;
>> +    MemoryRegion *mmio_alias, *mmio_halias, *mmio_reg;
>>       qemu_irq irq;
>>       int i;
>>
>> @@ -314,6 +324,11 @@ static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
>>                                mmio_reg, mmio_base, mmio_size);
>>       memory_region_add_subregion(get_system_memory(), mmio_base, mmio_alias);
>>
>> +    mmio_halias = g_new0(MemoryRegion, 1);
>> +    memory_region_init_alias(mmio_halias, OBJECT(dev), "pcie-mmio-high",
>> +                             mmio_reg, mmio_hbase, mmio_hsize);
>> +    memory_region_add_subregion(get_system_memory(), mmio_hbase, mmio_halias);
>> +
>>       sysbus_mmio_map(SYS_BUS_DEVICE(dev), 2, pio_base);
>>
>>       for (i = 0; i < GPEX_NUM_IRQS; i++) {
>> @@ -444,10 +459,12 @@ static void riscv_virt_board_init(MachineState *machine)
>>       }
>>
>>       dev = gpex_pcie_init(system_memory,
>> -                         memmap[VIRT_PCIE_MMIO].base,
>> -                         memmap[VIRT_PCIE_MMIO].size,
>>                            memmap[VIRT_PCIE_ECAM].base,
>>                            memmap[VIRT_PCIE_ECAM].size,
>> +                         memmap[VIRT_PCIE_MMIO].base,
>> +                         memmap[VIRT_PCIE_MMIO].size,
>> +                         memmap[VIRT_PCIE_MMIO_HIGH].base,
>> +                         memmap[VIRT_PCIE_MMIO_HIGH].size,
>>                            memmap[VIRT_PCIE_PIO].base,
>>                            DEVICE(s->plic), true);
>>       pci_bus = PCI_HOST_BRIDGE(dev)->bus;
>> diff --git a/include/hw/riscv/virt.h b/include/hw/riscv/virt.h
>> index dd4fedd..99caf09 100644
>> --- a/include/hw/riscv/virt.h
>> +++ b/include/hw/riscv/virt.h
>> @@ -40,6 +40,7 @@ enum {
>>       VIRT_VIRTIO,
>>       VIRT_DRAM,
>>       VIRT_PCIE_MMIO,
>> +    VIRT_PCIE_MMIO_HIGH,
>>       VIRT_PCIE_PIO,
>>       VIRT_PCIE_ECAM
>>   };
>> --
>> 2.7.4
>>
>>
>
Guenter Roeck Nov. 21, 2018, 4:07 a.m. UTC | #3
Hi Alistair,

On 11/20/18 4:43 PM, Alistair Francis wrote:
> On Tue, Nov 20, 2018 at 3:01 PM Guenter Roeck <linux@roeck-us.net> wrote:
>>
>> - Provide separate maps for VIRT_PCIE_MMIO (32 bit) and
>>    VIRT_PCIE_MMIO_HIGH (64 bit)
>> - VIRT_PCIE_PIO is for IO ports, not for the physical address
>> - VIRT_PCIE_ECAM size reduced to size needed to cover 256 ports
>> - Use memmap[VIRT_PCIE_ECAM].size instead of memmap[VIRT_PCIE_ECAM].base
>>    to calculate the bus number range
>> - Use qemu_fdt_setprop_sized_cells() to create reg and ranges entries
>> - Fix parameters for gpex_pcie_init()
>>    (ECAM and MMIO addresses were swapped)
>>
>> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
> 
> Hey Gunter,
> 
> Thanks for the patch! This was causing me all kinds of headaches.
> Unfortunately I had managed to figure out the memory addresses thanks
> to Bin Meng's help.
> 
> You can see the new tree here:
> https://github.com/alistair23/qemu/tree/mainline/alistair/sifive_pcie.next
> 

Looks good. With your patch series applied on top of v3.1-rc2 and usb.mak
added to the build:

Building riscv:virt:defconfig:initrd ... running ....... passed
Building riscv:virt:defconfig:virtio-blk:rootfs ... running ....... passed
Building riscv:virt:defconfig:virtio:rootfs ... running ....... passed
Building riscv:virt:defconfig:virtio-pci:rootfs ... running ....... passed
Building riscv:virt:defconfig:mmc:rootfs ... running ....... passed
Building riscv:virt:defconfig:nvme:rootfs ... running ................... passed
Building riscv:virt:defconfig:usb-ohci:rootfs ... running ....... passed
Building riscv:virt:defconfig:usb-ehci:rootfs ... running ....... passed
Building riscv:virt:defconfig:usb-xhci:rootfs ... running ....... passed
Building riscv:virt:defconfig:usb-uas-ehci:rootfs ... running ....... passed
Building riscv:virt:defconfig:usb-uas-xhci:rootfs ... running ....... passed
Building riscv:virt:defconfig:scsi[53C810]:rootfs ... running ........ passed
Building riscv:virt:defconfig:scsi[53C895A]:rootfs ... running ........ passed
Building riscv:virt:defconfig:scsi[MEGASAS]:rootfs ... running ....... passed
Building riscv:virt:defconfig:scsi[MEGASAS2]:rootfs ... running ....... passed
Building riscv:virt:defconfig:scsi[FUSION]:rootfs ... running ....... passed
Building riscv:virt:defconfig:scsi[virtio]:rootfs ... running ....... passed
Building riscv:virt:defconfig:scsi[virtio-pci]:rootfs ... running ....... passed

Guenter
Alistair Francis Nov. 21, 2018, 4 p.m. UTC | #4
On Tue, Nov 20, 2018 at 5:54 PM Guenter Roeck <linux@roeck-us.net> wrote:
>
> Hi Alistair,
>
> On 11/20/18 4:43 PM, Alistair Francis wrote:
> > On Tue, Nov 20, 2018 at 3:01 PM Guenter Roeck <linux@roeck-us.net> wrote:
> >>
> >> - Provide separate maps for VIRT_PCIE_MMIO (32 bit) and
> >>    VIRT_PCIE_MMIO_HIGH (64 bit)
> >> - VIRT_PCIE_PIO is for IO ports, not for the physical address
> >> - VIRT_PCIE_ECAM size reduced to size needed to cover 256 ports
> >> - Use memmap[VIRT_PCIE_ECAM].size instead of memmap[VIRT_PCIE_ECAM].base
> >>    to calculate the bus number range
> >> - Use qemu_fdt_setprop_sized_cells() to create reg and ranges entries
> >> - Fix parameters for gpex_pcie_init()
> >>    (ECAM and MMIO addresses were swapped)
> >>
> >> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
> >
> > Hey Gunter,
> >
> > Thanks for the patch! This was causing me all kinds of headaches.
> > Unfortunately I had managed to figure out the memory addresses thanks
> > to Bin Meng's help.
> >
> No worries. I am not married to this series. I'll give your tree a try,
> hopefully tonight.
>
> > You can see the new tree here:
> > https://github.com/alistair23/qemu/tree/mainline/alistair/sifive_pcie.next
> >
> > If you have anything you wan to add to that branch just let me know.
> >
>
> One possible addition might be a 64 bit address range. I don't know
> if that is needed for some pcie devices. I do see that nvme instantiates
> from the 64 bit region, but I don't know if that is mandatory or just the
> preference.
>
> I would also suggest to add "include usb.mak" to the defconfig file. With this,
> it is possible to support the full range of usb devices. I am using it for
> various boot tests.

I agree that both of these would be nice. At the moment I am going to
leave them out as I just want this series merged and I suspect adding
more patches will slow the process down even more. Once it's in we can
look at 64-bit address ranges and adding USB support (something I am
also interested in).

Alistair

>
> Thanks,
> Guenter
>
> > Alistair
> >
> >> ---
> >> This series applies on top of
> >>          https://patchwork.kernel.org/cover/10661699/
> >>
> >> Tested with mmc:
> >>      qemu-system-riscv64 -M virt -m 512M -no-reboot \
> >>          -bios riscv64/bbl -kernel vmlinux \
> >>          -netdev user,id=net0 -device virtio-net-device,netdev=net0 \
> >>          -snapshot -device sdhci-pci -device sd-card,drive=d0 \
> >>          -drive file=rootfs.ext2,format=raw,if=none,id=d0 \
> >>          -append 'root=/dev/mmcblk0 rw rootwait panic=-1 console=ttyS0,115200' \
> >>          -nographic -monitor none
> >>
> >> and nvme:
> >>      qemu-system-riscv64 -M virt -m 512M -no-reboot \
> >>          -bios riscv64/bbl -kernel vmlinux \
> >>          -netdev user,id=net0 -device virtio-net-device,netdev=net0 \
> >>          -snapshot -device nvme,serial=foo,drive=d0 \
> >>          -drive file=rootfs.ext2,if=none,format=raw,id=d0 \
> >>          -append 'root=/dev/nvme0n1 rw rootwait panic=-1 console=ttyS0,115200' \
> >>          -nographic -monitor none
> >>
> >>   hw/riscv/virt.c         | 51 ++++++++++++++++++++++++++++++++-----------------
> >>   include/hw/riscv/virt.h |  1 +
> >>   2 files changed, 35 insertions(+), 17 deletions(-)
> >>
> >> diff --git a/hw/riscv/virt.c b/hw/riscv/virt.c
> >> index 1aac5ca..675899d 100644
> >> --- a/hw/riscv/virt.c
> >> +++ b/hw/riscv/virt.c
> >> @@ -59,10 +59,10 @@ static const struct MemmapEntry {
> >>       [VIRT_UART0] =    { 0x10000000,      0x100 },
> >>       [VIRT_VIRTIO] =   { 0x10001000,     0x1000 },
> >>       [VIRT_DRAM] =     { 0x80000000,        0x0 },
> >> -    [VIRT_PCIE_MMIO] = { 0x2000000000, 0x4000000 },
> >> -    [VIRT_PCIE_PIO] = { 0x2010000, 0x40000000 },
> >> -    [VIRT_PCIE_ECAM] = { 0x40000000, 0x20000000 },
> >> -
> >> +    [VIRT_PCIE_MMIO] = { 0x40000000, 0x40000000 },
> >> +    [VIRT_PCIE_MMIO_HIGH] = { 0x2000000000, 0x4000000000 },
> >> +    [VIRT_PCIE_PIO] =  { 0x10002000,     0x1000 },
> >> +    [VIRT_PCIE_ECAM] = { 0x30000000, 0x10000000 },
> >>   };
> >>
> >>   #define INTERREUPT_MAP_WIDTH 7
> >> @@ -231,8 +231,7 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
> >>           g_free(nodename);
> >>       }
> >>
> >> -    nodename = g_strdup_printf("/pci@%lx",
> >> -        (long) memmap[VIRT_PCIE_MMIO].base);
> >> +    nodename = g_strdup_printf("/pcie@%" PRIx64, memmap[VIRT_PCIE_MMIO].base);
> >>       qemu_fdt_add_subnode(fdt, nodename);
> >>       qemu_fdt_setprop_cells(fdt, nodename, "#address-cells", 0x3);
> >>       qemu_fdt_setprop_cells(fdt, nodename, "#interrupt-cells", 0x1);
> >> @@ -242,16 +241,26 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
> >>       qemu_fdt_setprop_string(fdt, nodename, "device_type", "pci");
> >>       qemu_fdt_setprop_cell(fdt, nodename, "linux,pci-domain", 0);
> >>       qemu_fdt_setprop_cells(fdt, nodename, "bus-range", 0,
> >> -                           memmap[VIRT_PCIE_ECAM].base /
> >> +                           memmap[VIRT_PCIE_ECAM].size /
> >>                                  PCIE_MMCFG_SIZE_MIN - 1);
> >>       qemu_fdt_setprop(fdt, nodename, "dma-coherent", NULL, 0);
> >> -    qemu_fdt_setprop_cells(fdt, nodename, "reg", 0x20, 0,
> >> -                           0, memmap[VIRT_PCIE_ECAM].size);
> >> -    qemu_fdt_setprop_cells(fdt, nodename, "ranges",
> >> -                           memmap[VIRT_PCIE_PIO].base,
> >> -                               0, memmap[VIRT_PCIE_PIO].size,
> >> -                           0, memmap[VIRT_PCIE_MMIO].base,
> >> -                               0, memmap[VIRT_PCIE_MMIO].size);
> >> +    qemu_fdt_setprop_sized_cells(fdt, nodename, "reg",
> >> +                                 2, memmap[VIRT_PCIE_ECAM].base,
> >> +                                 2, memmap[VIRT_PCIE_ECAM].size);
> >> +
> >> +    qemu_fdt_setprop_sized_cells(fdt, nodename, "ranges",
> >> +                                 1, FDT_PCI_RANGE_IOPORT, 2, 0,
> >> +                                 2, memmap[VIRT_PCIE_PIO].base,
> >> +                                 2, memmap[VIRT_PCIE_PIO].size,
> >> +                                 1, FDT_PCI_RANGE_MMIO,
> >> +                                 2, memmap[VIRT_PCIE_MMIO].base,
> >> +                                 2, memmap[VIRT_PCIE_MMIO].base,
> >> +                                 2, memmap[VIRT_PCIE_MMIO].size,
> >> +                                 1, FDT_PCI_RANGE_MMIO_64BIT,
> >> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
> >> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
> >> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].size);
> >> +
> >>       qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
> >>       qemu_fdt_setprop_cells(fdt, nodename, "interrupts", PCIE_IRQ);
> >>       create_pcie_irq_map(fdt, nodename, plic_phandle);
> >> @@ -289,12 +298,13 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
> >>   static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
> >>                                             hwaddr ecam_base, hwaddr ecam_size,
> >>                                             hwaddr mmio_base, hwaddr mmio_size,
> >> +                                          hwaddr mmio_hbase, hwaddr mmio_hsize,
> >>                                             hwaddr pio_base,
> >>                                             DeviceState *plic, bool link_up)
> >>   {
> >>       DeviceState *dev;
> >>       MemoryRegion *ecam_alias, *ecam_reg;
> >> -    MemoryRegion *mmio_alias, *mmio_reg;
> >> +    MemoryRegion *mmio_alias, *mmio_halias, *mmio_reg;
> >>       qemu_irq irq;
> >>       int i;
> >>
> >> @@ -314,6 +324,11 @@ static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
> >>                                mmio_reg, mmio_base, mmio_size);
> >>       memory_region_add_subregion(get_system_memory(), mmio_base, mmio_alias);
> >>
> >> +    mmio_halias = g_new0(MemoryRegion, 1);
> >> +    memory_region_init_alias(mmio_halias, OBJECT(dev), "pcie-mmio-high",
> >> +                             mmio_reg, mmio_hbase, mmio_hsize);
> >> +    memory_region_add_subregion(get_system_memory(), mmio_hbase, mmio_halias);
> >> +
> >>       sysbus_mmio_map(SYS_BUS_DEVICE(dev), 2, pio_base);
> >>
> >>       for (i = 0; i < GPEX_NUM_IRQS; i++) {
> >> @@ -444,10 +459,12 @@ static void riscv_virt_board_init(MachineState *machine)
> >>       }
> >>
> >>       dev = gpex_pcie_init(system_memory,
> >> -                         memmap[VIRT_PCIE_MMIO].base,
> >> -                         memmap[VIRT_PCIE_MMIO].size,
> >>                            memmap[VIRT_PCIE_ECAM].base,
> >>                            memmap[VIRT_PCIE_ECAM].size,
> >> +                         memmap[VIRT_PCIE_MMIO].base,
> >> +                         memmap[VIRT_PCIE_MMIO].size,
> >> +                         memmap[VIRT_PCIE_MMIO_HIGH].base,
> >> +                         memmap[VIRT_PCIE_MMIO_HIGH].size,
> >>                            memmap[VIRT_PCIE_PIO].base,
> >>                            DEVICE(s->plic), true);
> >>       pci_bus = PCI_HOST_BRIDGE(dev)->bus;
> >> diff --git a/include/hw/riscv/virt.h b/include/hw/riscv/virt.h
> >> index dd4fedd..99caf09 100644
> >> --- a/include/hw/riscv/virt.h
> >> +++ b/include/hw/riscv/virt.h
> >> @@ -40,6 +40,7 @@ enum {
> >>       VIRT_VIRTIO,
> >>       VIRT_DRAM,
> >>       VIRT_PCIE_MMIO,
> >> +    VIRT_PCIE_MMIO_HIGH,
> >>       VIRT_PCIE_PIO,
> >>       VIRT_PCIE_ECAM
> >>   };
> >> --
> >> 2.7.4
> >>
> >>
> >
>
Alistair Francis Nov. 21, 2018, 4 p.m. UTC | #5
On Tue, Nov 20, 2018 at 8:08 PM Guenter Roeck <linux@roeck-us.net> wrote:
>
> Hi Alistair,
>
> On 11/20/18 4:43 PM, Alistair Francis wrote:
> > On Tue, Nov 20, 2018 at 3:01 PM Guenter Roeck <linux@roeck-us.net> wrote:
> >>
> >> - Provide separate maps for VIRT_PCIE_MMIO (32 bit) and
> >>    VIRT_PCIE_MMIO_HIGH (64 bit)
> >> - VIRT_PCIE_PIO is for IO ports, not for the physical address
> >> - VIRT_PCIE_ECAM size reduced to size needed to cover 256 ports
> >> - Use memmap[VIRT_PCIE_ECAM].size instead of memmap[VIRT_PCIE_ECAM].base
> >>    to calculate the bus number range
> >> - Use qemu_fdt_setprop_sized_cells() to create reg and ranges entries
> >> - Fix parameters for gpex_pcie_init()
> >>    (ECAM and MMIO addresses were swapped)
> >>
> >> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
> >
> > Hey Gunter,
> >
> > Thanks for the patch! This was causing me all kinds of headaches.
> > Unfortunately I had managed to figure out the memory addresses thanks
> > to Bin Meng's help.
> >
> > You can see the new tree here:
> > https://github.com/alistair23/qemu/tree/mainline/alistair/sifive_pcie.next
> >
>
> Looks good. With your patch series applied on top of v3.1-rc2 and usb.mak
> added to the build:
>
> Building riscv:virt:defconfig:initrd ... running ....... passed
> Building riscv:virt:defconfig:virtio-blk:rootfs ... running ....... passed
> Building riscv:virt:defconfig:virtio:rootfs ... running ....... passed
> Building riscv:virt:defconfig:virtio-pci:rootfs ... running ....... passed
> Building riscv:virt:defconfig:mmc:rootfs ... running ....... passed
> Building riscv:virt:defconfig:nvme:rootfs ... running ................... passed
> Building riscv:virt:defconfig:usb-ohci:rootfs ... running ....... passed
> Building riscv:virt:defconfig:usb-ehci:rootfs ... running ....... passed
> Building riscv:virt:defconfig:usb-xhci:rootfs ... running ....... passed
> Building riscv:virt:defconfig:usb-uas-ehci:rootfs ... running ....... passed
> Building riscv:virt:defconfig:usb-uas-xhci:rootfs ... running ....... passed
> Building riscv:virt:defconfig:scsi[53C810]:rootfs ... running ........ passed
> Building riscv:virt:defconfig:scsi[53C895A]:rootfs ... running ........ passed
> Building riscv:virt:defconfig:scsi[MEGASAS]:rootfs ... running ....... passed
> Building riscv:virt:defconfig:scsi[MEGASAS2]:rootfs ... running ....... passed
> Building riscv:virt:defconfig:scsi[FUSION]:rootfs ... running ....... passed
> Building riscv:virt:defconfig:scsi[virtio]:rootfs ... running ....... passed
> Building riscv:virt:defconfig:scsi[virtio-pci]:rootfs ... running ....... passed

Awesome! Can I add your tested by tag?

Alistair

>
> Guenter
Guenter Roeck Nov. 21, 2018, 7:04 p.m. UTC | #6
On Wed, Nov 21, 2018 at 08:00:45AM -0800, Alistair Francis wrote:
> On Tue, Nov 20, 2018 at 8:08 PM Guenter Roeck <linux@roeck-us.net> wrote:
> >
> > Hi Alistair,
> >
> > On 11/20/18 4:43 PM, Alistair Francis wrote:
> > > On Tue, Nov 20, 2018 at 3:01 PM Guenter Roeck <linux@roeck-us.net> wrote:
> > >>
> > >> - Provide separate maps for VIRT_PCIE_MMIO (32 bit) and
> > >>    VIRT_PCIE_MMIO_HIGH (64 bit)
> > >> - VIRT_PCIE_PIO is for IO ports, not for the physical address
> > >> - VIRT_PCIE_ECAM size reduced to size needed to cover 256 ports
> > >> - Use memmap[VIRT_PCIE_ECAM].size instead of memmap[VIRT_PCIE_ECAM].base
> > >>    to calculate the bus number range
> > >> - Use qemu_fdt_setprop_sized_cells() to create reg and ranges entries
> > >> - Fix parameters for gpex_pcie_init()
> > >>    (ECAM and MMIO addresses were swapped)
> > >>
> > >> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
> > >
> > > Hey Gunter,
> > >
> > > Thanks for the patch! This was causing me all kinds of headaches.
> > > Unfortunately I had managed to figure out the memory addresses thanks
> > > to Bin Meng's help.
> > >
> > > You can see the new tree here:
> > > https://github.com/alistair23/qemu/tree/mainline/alistair/sifive_pcie.next
> > >
> >
> > Looks good. With your patch series applied on top of v3.1-rc2 and usb.mak
> > added to the build:
> >
> > Building riscv:virt:defconfig:initrd ... running ....... passed
> > Building riscv:virt:defconfig:virtio-blk:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:virtio:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:virtio-pci:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:mmc:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:nvme:rootfs ... running ................... passed
> > Building riscv:virt:defconfig:usb-ohci:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:usb-ehci:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:usb-xhci:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:usb-uas-ehci:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:usb-uas-xhci:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:scsi[53C810]:rootfs ... running ........ passed
> > Building riscv:virt:defconfig:scsi[53C895A]:rootfs ... running ........ passed
> > Building riscv:virt:defconfig:scsi[MEGASAS]:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:scsi[MEGASAS2]:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:scsi[FUSION]:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:scsi[virtio]:rootfs ... running ....... passed
> > Building riscv:virt:defconfig:scsi[virtio-pci]:rootfs ... running ....... passed
> 
> Awesome! Can I add your tested by tag?
> 
Sure, go ahead.

Guenter

> Alistair
> 
> >
> > Guenter
Guenter Roeck Nov. 21, 2018, 7:05 p.m. UTC | #7
On Wed, Nov 21, 2018 at 08:00:08AM -0800, Alistair Francis wrote:
> On Tue, Nov 20, 2018 at 5:54 PM Guenter Roeck <linux@roeck-us.net> wrote:
> >
> > Hi Alistair,
> >
> > On 11/20/18 4:43 PM, Alistair Francis wrote:
> > > On Tue, Nov 20, 2018 at 3:01 PM Guenter Roeck <linux@roeck-us.net> wrote:
> > >>
> > >> - Provide separate maps for VIRT_PCIE_MMIO (32 bit) and
> > >>    VIRT_PCIE_MMIO_HIGH (64 bit)
> > >> - VIRT_PCIE_PIO is for IO ports, not for the physical address
> > >> - VIRT_PCIE_ECAM size reduced to size needed to cover 256 ports
> > >> - Use memmap[VIRT_PCIE_ECAM].size instead of memmap[VIRT_PCIE_ECAM].base
> > >>    to calculate the bus number range
> > >> - Use qemu_fdt_setprop_sized_cells() to create reg and ranges entries
> > >> - Fix parameters for gpex_pcie_init()
> > >>    (ECAM and MMIO addresses were swapped)
> > >>
> > >> Signed-off-by: Guenter Roeck <linux@roeck-us.net>
> > >
> > > Hey Gunter,
> > >
> > > Thanks for the patch! This was causing me all kinds of headaches.
> > > Unfortunately I had managed to figure out the memory addresses thanks
> > > to Bin Meng's help.
> > >
> > No worries. I am not married to this series. I'll give your tree a try,
> > hopefully tonight.
> >
> > > You can see the new tree here:
> > > https://github.com/alistair23/qemu/tree/mainline/alistair/sifive_pcie.next
> > >
> > > If you have anything you wan to add to that branch just let me know.
> > >
> >
> > One possible addition might be a 64 bit address range. I don't know
> > if that is needed for some pcie devices. I do see that nvme instantiates
> > from the 64 bit region, but I don't know if that is mandatory or just the
> > preference.
> >
> > I would also suggest to add "include usb.mak" to the defconfig file. With this,
> > it is possible to support the full range of usb devices. I am using it for
> > various boot tests.
> 
> I agree that both of these would be nice. At the moment I am going to
> leave them out as I just want this series merged and I suspect adding
> more patches will slow the process down even more. Once it's in we can
> look at 64-bit address ranges and adding USB support (something I am
> also interested in).
> 
Makes sense.

Thanks,
Guenter

> Alistair
> 
> >
> > Thanks,
> > Guenter
> >
> > > Alistair
> > >
> > >> ---
> > >> This series applies on top of
> > >>          https://patchwork.kernel.org/cover/10661699/
> > >>
> > >> Tested with mmc:
> > >>      qemu-system-riscv64 -M virt -m 512M -no-reboot \
> > >>          -bios riscv64/bbl -kernel vmlinux \
> > >>          -netdev user,id=net0 -device virtio-net-device,netdev=net0 \
> > >>          -snapshot -device sdhci-pci -device sd-card,drive=d0 \
> > >>          -drive file=rootfs.ext2,format=raw,if=none,id=d0 \
> > >>          -append 'root=/dev/mmcblk0 rw rootwait panic=-1 console=ttyS0,115200' \
> > >>          -nographic -monitor none
> > >>
> > >> and nvme:
> > >>      qemu-system-riscv64 -M virt -m 512M -no-reboot \
> > >>          -bios riscv64/bbl -kernel vmlinux \
> > >>          -netdev user,id=net0 -device virtio-net-device,netdev=net0 \
> > >>          -snapshot -device nvme,serial=foo,drive=d0 \
> > >>          -drive file=rootfs.ext2,if=none,format=raw,id=d0 \
> > >>          -append 'root=/dev/nvme0n1 rw rootwait panic=-1 console=ttyS0,115200' \
> > >>          -nographic -monitor none
> > >>
> > >>   hw/riscv/virt.c         | 51 ++++++++++++++++++++++++++++++++-----------------
> > >>   include/hw/riscv/virt.h |  1 +
> > >>   2 files changed, 35 insertions(+), 17 deletions(-)
> > >>
> > >> diff --git a/hw/riscv/virt.c b/hw/riscv/virt.c
> > >> index 1aac5ca..675899d 100644
> > >> --- a/hw/riscv/virt.c
> > >> +++ b/hw/riscv/virt.c
> > >> @@ -59,10 +59,10 @@ static const struct MemmapEntry {
> > >>       [VIRT_UART0] =    { 0x10000000,      0x100 },
> > >>       [VIRT_VIRTIO] =   { 0x10001000,     0x1000 },
> > >>       [VIRT_DRAM] =     { 0x80000000,        0x0 },
> > >> -    [VIRT_PCIE_MMIO] = { 0x2000000000, 0x4000000 },
> > >> -    [VIRT_PCIE_PIO] = { 0x2010000, 0x40000000 },
> > >> -    [VIRT_PCIE_ECAM] = { 0x40000000, 0x20000000 },
> > >> -
> > >> +    [VIRT_PCIE_MMIO] = { 0x40000000, 0x40000000 },
> > >> +    [VIRT_PCIE_MMIO_HIGH] = { 0x2000000000, 0x4000000000 },
> > >> +    [VIRT_PCIE_PIO] =  { 0x10002000,     0x1000 },
> > >> +    [VIRT_PCIE_ECAM] = { 0x30000000, 0x10000000 },
> > >>   };
> > >>
> > >>   #define INTERREUPT_MAP_WIDTH 7
> > >> @@ -231,8 +231,7 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
> > >>           g_free(nodename);
> > >>       }
> > >>
> > >> -    nodename = g_strdup_printf("/pci@%lx",
> > >> -        (long) memmap[VIRT_PCIE_MMIO].base);
> > >> +    nodename = g_strdup_printf("/pcie@%" PRIx64, memmap[VIRT_PCIE_MMIO].base);
> > >>       qemu_fdt_add_subnode(fdt, nodename);
> > >>       qemu_fdt_setprop_cells(fdt, nodename, "#address-cells", 0x3);
> > >>       qemu_fdt_setprop_cells(fdt, nodename, "#interrupt-cells", 0x1);
> > >> @@ -242,16 +241,26 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
> > >>       qemu_fdt_setprop_string(fdt, nodename, "device_type", "pci");
> > >>       qemu_fdt_setprop_cell(fdt, nodename, "linux,pci-domain", 0);
> > >>       qemu_fdt_setprop_cells(fdt, nodename, "bus-range", 0,
> > >> -                           memmap[VIRT_PCIE_ECAM].base /
> > >> +                           memmap[VIRT_PCIE_ECAM].size /
> > >>                                  PCIE_MMCFG_SIZE_MIN - 1);
> > >>       qemu_fdt_setprop(fdt, nodename, "dma-coherent", NULL, 0);
> > >> -    qemu_fdt_setprop_cells(fdt, nodename, "reg", 0x20, 0,
> > >> -                           0, memmap[VIRT_PCIE_ECAM].size);
> > >> -    qemu_fdt_setprop_cells(fdt, nodename, "ranges",
> > >> -                           memmap[VIRT_PCIE_PIO].base,
> > >> -                               0, memmap[VIRT_PCIE_PIO].size,
> > >> -                           0, memmap[VIRT_PCIE_MMIO].base,
> > >> -                               0, memmap[VIRT_PCIE_MMIO].size);
> > >> +    qemu_fdt_setprop_sized_cells(fdt, nodename, "reg",
> > >> +                                 2, memmap[VIRT_PCIE_ECAM].base,
> > >> +                                 2, memmap[VIRT_PCIE_ECAM].size);
> > >> +
> > >> +    qemu_fdt_setprop_sized_cells(fdt, nodename, "ranges",
> > >> +                                 1, FDT_PCI_RANGE_IOPORT, 2, 0,
> > >> +                                 2, memmap[VIRT_PCIE_PIO].base,
> > >> +                                 2, memmap[VIRT_PCIE_PIO].size,
> > >> +                                 1, FDT_PCI_RANGE_MMIO,
> > >> +                                 2, memmap[VIRT_PCIE_MMIO].base,
> > >> +                                 2, memmap[VIRT_PCIE_MMIO].base,
> > >> +                                 2, memmap[VIRT_PCIE_MMIO].size,
> > >> +                                 1, FDT_PCI_RANGE_MMIO_64BIT,
> > >> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
> > >> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
> > >> +                                 2, memmap[VIRT_PCIE_MMIO_HIGH].size);
> > >> +
> > >>       qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
> > >>       qemu_fdt_setprop_cells(fdt, nodename, "interrupts", PCIE_IRQ);
> > >>       create_pcie_irq_map(fdt, nodename, plic_phandle);
> > >> @@ -289,12 +298,13 @@ static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
> > >>   static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
> > >>                                             hwaddr ecam_base, hwaddr ecam_size,
> > >>                                             hwaddr mmio_base, hwaddr mmio_size,
> > >> +                                          hwaddr mmio_hbase, hwaddr mmio_hsize,
> > >>                                             hwaddr pio_base,
> > >>                                             DeviceState *plic, bool link_up)
> > >>   {
> > >>       DeviceState *dev;
> > >>       MemoryRegion *ecam_alias, *ecam_reg;
> > >> -    MemoryRegion *mmio_alias, *mmio_reg;
> > >> +    MemoryRegion *mmio_alias, *mmio_halias, *mmio_reg;
> > >>       qemu_irq irq;
> > >>       int i;
> > >>
> > >> @@ -314,6 +324,11 @@ static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
> > >>                                mmio_reg, mmio_base, mmio_size);
> > >>       memory_region_add_subregion(get_system_memory(), mmio_base, mmio_alias);
> > >>
> > >> +    mmio_halias = g_new0(MemoryRegion, 1);
> > >> +    memory_region_init_alias(mmio_halias, OBJECT(dev), "pcie-mmio-high",
> > >> +                             mmio_reg, mmio_hbase, mmio_hsize);
> > >> +    memory_region_add_subregion(get_system_memory(), mmio_hbase, mmio_halias);
> > >> +
> > >>       sysbus_mmio_map(SYS_BUS_DEVICE(dev), 2, pio_base);
> > >>
> > >>       for (i = 0; i < GPEX_NUM_IRQS; i++) {
> > >> @@ -444,10 +459,12 @@ static void riscv_virt_board_init(MachineState *machine)
> > >>       }
> > >>
> > >>       dev = gpex_pcie_init(system_memory,
> > >> -                         memmap[VIRT_PCIE_MMIO].base,
> > >> -                         memmap[VIRT_PCIE_MMIO].size,
> > >>                            memmap[VIRT_PCIE_ECAM].base,
> > >>                            memmap[VIRT_PCIE_ECAM].size,
> > >> +                         memmap[VIRT_PCIE_MMIO].base,
> > >> +                         memmap[VIRT_PCIE_MMIO].size,
> > >> +                         memmap[VIRT_PCIE_MMIO_HIGH].base,
> > >> +                         memmap[VIRT_PCIE_MMIO_HIGH].size,
> > >>                            memmap[VIRT_PCIE_PIO].base,
> > >>                            DEVICE(s->plic), true);
> > >>       pci_bus = PCI_HOST_BRIDGE(dev)->bus;
> > >> diff --git a/include/hw/riscv/virt.h b/include/hw/riscv/virt.h
> > >> index dd4fedd..99caf09 100644
> > >> --- a/include/hw/riscv/virt.h
> > >> +++ b/include/hw/riscv/virt.h
> > >> @@ -40,6 +40,7 @@ enum {
> > >>       VIRT_VIRTIO,
> > >>       VIRT_DRAM,
> > >>       VIRT_PCIE_MMIO,
> > >> +    VIRT_PCIE_MMIO_HIGH,
> > >>       VIRT_PCIE_PIO,
> > >>       VIRT_PCIE_ECAM
> > >>   };
> > >> --
> > >> 2.7.4
> > >>
> > >>
> > >
> >
diff mbox series

Patch

diff --git a/hw/riscv/virt.c b/hw/riscv/virt.c
index 1aac5ca..675899d 100644
--- a/hw/riscv/virt.c
+++ b/hw/riscv/virt.c
@@ -59,10 +59,10 @@  static const struct MemmapEntry {
     [VIRT_UART0] =    { 0x10000000,      0x100 },
     [VIRT_VIRTIO] =   { 0x10001000,     0x1000 },
     [VIRT_DRAM] =     { 0x80000000,        0x0 },
-    [VIRT_PCIE_MMIO] = { 0x2000000000, 0x4000000 },
-    [VIRT_PCIE_PIO] = { 0x2010000, 0x40000000 },
-    [VIRT_PCIE_ECAM] = { 0x40000000, 0x20000000 },
-
+    [VIRT_PCIE_MMIO] = { 0x40000000, 0x40000000 },
+    [VIRT_PCIE_MMIO_HIGH] = { 0x2000000000, 0x4000000000 },
+    [VIRT_PCIE_PIO] =  { 0x10002000,     0x1000 },
+    [VIRT_PCIE_ECAM] = { 0x30000000, 0x10000000 },
 };
 
 #define INTERREUPT_MAP_WIDTH 7
@@ -231,8 +231,7 @@  static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
         g_free(nodename);
     }
 
-    nodename = g_strdup_printf("/pci@%lx",
-        (long) memmap[VIRT_PCIE_MMIO].base);
+    nodename = g_strdup_printf("/pcie@%" PRIx64, memmap[VIRT_PCIE_MMIO].base);
     qemu_fdt_add_subnode(fdt, nodename);
     qemu_fdt_setprop_cells(fdt, nodename, "#address-cells", 0x3);
     qemu_fdt_setprop_cells(fdt, nodename, "#interrupt-cells", 0x1);
@@ -242,16 +241,26 @@  static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
     qemu_fdt_setprop_string(fdt, nodename, "device_type", "pci");
     qemu_fdt_setprop_cell(fdt, nodename, "linux,pci-domain", 0);
     qemu_fdt_setprop_cells(fdt, nodename, "bus-range", 0,
-                           memmap[VIRT_PCIE_ECAM].base /
+                           memmap[VIRT_PCIE_ECAM].size /
                                PCIE_MMCFG_SIZE_MIN - 1);
     qemu_fdt_setprop(fdt, nodename, "dma-coherent", NULL, 0);
-    qemu_fdt_setprop_cells(fdt, nodename, "reg", 0x20, 0,
-                           0, memmap[VIRT_PCIE_ECAM].size);
-    qemu_fdt_setprop_cells(fdt, nodename, "ranges",
-                           memmap[VIRT_PCIE_PIO].base,
-                               0, memmap[VIRT_PCIE_PIO].size,
-                           0, memmap[VIRT_PCIE_MMIO].base,
-                               0, memmap[VIRT_PCIE_MMIO].size);
+    qemu_fdt_setprop_sized_cells(fdt, nodename, "reg",
+                                 2, memmap[VIRT_PCIE_ECAM].base,
+                                 2, memmap[VIRT_PCIE_ECAM].size);
+
+    qemu_fdt_setprop_sized_cells(fdt, nodename, "ranges",
+                                 1, FDT_PCI_RANGE_IOPORT, 2, 0,
+                                 2, memmap[VIRT_PCIE_PIO].base,
+                                 2, memmap[VIRT_PCIE_PIO].size,
+                                 1, FDT_PCI_RANGE_MMIO,
+                                 2, memmap[VIRT_PCIE_MMIO].base,
+                                 2, memmap[VIRT_PCIE_MMIO].base,
+                                 2, memmap[VIRT_PCIE_MMIO].size,
+                                 1, FDT_PCI_RANGE_MMIO_64BIT,
+                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
+                                 2, memmap[VIRT_PCIE_MMIO_HIGH].base,
+                                 2, memmap[VIRT_PCIE_MMIO_HIGH].size);
+
     qemu_fdt_setprop_cells(fdt, nodename, "interrupt-parent", plic_phandle);
     qemu_fdt_setprop_cells(fdt, nodename, "interrupts", PCIE_IRQ);
     create_pcie_irq_map(fdt, nodename, plic_phandle);
@@ -289,12 +298,13 @@  static void *create_fdt(RISCVVirtState *s, const struct MemmapEntry *memmap,
 static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
                                           hwaddr ecam_base, hwaddr ecam_size,
                                           hwaddr mmio_base, hwaddr mmio_size,
+                                          hwaddr mmio_hbase, hwaddr mmio_hsize,
                                           hwaddr pio_base,
                                           DeviceState *plic, bool link_up)
 {
     DeviceState *dev;
     MemoryRegion *ecam_alias, *ecam_reg;
-    MemoryRegion *mmio_alias, *mmio_reg;
+    MemoryRegion *mmio_alias, *mmio_halias, *mmio_reg;
     qemu_irq irq;
     int i;
 
@@ -314,6 +324,11 @@  static inline DeviceState *gpex_pcie_init(MemoryRegion *sys_mem,
                              mmio_reg, mmio_base, mmio_size);
     memory_region_add_subregion(get_system_memory(), mmio_base, mmio_alias);
 
+    mmio_halias = g_new0(MemoryRegion, 1);
+    memory_region_init_alias(mmio_halias, OBJECT(dev), "pcie-mmio-high",
+                             mmio_reg, mmio_hbase, mmio_hsize);
+    memory_region_add_subregion(get_system_memory(), mmio_hbase, mmio_halias);
+
     sysbus_mmio_map(SYS_BUS_DEVICE(dev), 2, pio_base);
 
     for (i = 0; i < GPEX_NUM_IRQS; i++) {
@@ -444,10 +459,12 @@  static void riscv_virt_board_init(MachineState *machine)
     }
 
     dev = gpex_pcie_init(system_memory,
-                         memmap[VIRT_PCIE_MMIO].base,
-                         memmap[VIRT_PCIE_MMIO].size,
                          memmap[VIRT_PCIE_ECAM].base,
                          memmap[VIRT_PCIE_ECAM].size,
+                         memmap[VIRT_PCIE_MMIO].base,
+                         memmap[VIRT_PCIE_MMIO].size,
+                         memmap[VIRT_PCIE_MMIO_HIGH].base,
+                         memmap[VIRT_PCIE_MMIO_HIGH].size,
                          memmap[VIRT_PCIE_PIO].base,
                          DEVICE(s->plic), true);
     pci_bus = PCI_HOST_BRIDGE(dev)->bus;
diff --git a/include/hw/riscv/virt.h b/include/hw/riscv/virt.h
index dd4fedd..99caf09 100644
--- a/include/hw/riscv/virt.h
+++ b/include/hw/riscv/virt.h
@@ -40,6 +40,7 @@  enum {
     VIRT_VIRTIO,
     VIRT_DRAM,
     VIRT_PCIE_MMIO,
+    VIRT_PCIE_MMIO_HIGH,
     VIRT_PCIE_PIO,
     VIRT_PCIE_ECAM
 };