diff mbox

amba_pl022: Setup SPI configuration based on spi->mode

Message ID 1283446992-23764-1-git-send-email-wellsk40@gmail.com
State Superseded, archived
Headers show

Commit Message

wellsk40@gmail.com Sept. 2, 2010, 5:03 p.m. UTC
None
diff mbox

Patch

diff --git a/drivers/spi/amba-pl022.c b/drivers/spi/amba-pl022.c
index acd35d1..1be488a 100644
--- a/drivers/spi/amba-pl022.c
+++ b/drivers/spi/amba-pl022.c
@@ -1248,12 +1248,6 @@  static int destroy_queue(struct pl022 *pl022)
 static int verify_controller_parameters(struct pl022 *pl022,
 					struct pl022_config_chip *chip_info)
 {
-	if ((chip_info->lbm != LOOPBACK_ENABLED)
-	    && (chip_info->lbm != LOOPBACK_DISABLED)) {
-		dev_err(chip_info->dev,
-			"loopback Mode is configured incorrectly\n");
-		return -EINVAL;
-	}
 	if ((chip_info->iface < SSP_INTERFACE_MOTOROLA_SPI)
 	    || (chip_info->iface > SSP_INTERFACE_UNIDIRECTIONAL)) {
 		dev_err(chip_info->dev,
@@ -1279,24 +1273,6 @@  static int verify_controller_parameters(struct pl022 *pl022,
 			"cpsdvsr is configured incorrectly\n");
 		return -EINVAL;
 	}
-	if ((chip_info->endian_rx != SSP_RX_MSB)
-	    && (chip_info->endian_rx != SSP_RX_LSB)) {
-		dev_err(chip_info->dev,
-			"RX FIFO endianess is configured incorrectly\n");
-		return -EINVAL;
-	}
-	if ((chip_info->endian_tx != SSP_TX_MSB)
-	    && (chip_info->endian_tx != SSP_TX_LSB)) {
-		dev_err(chip_info->dev,
-			"TX FIFO endianess is configured incorrectly\n");
-		return -EINVAL;
-	}
-	if ((chip_info->data_size < SSP_DATA_BITS_4)
-	    || (chip_info->data_size > SSP_DATA_BITS_32)) {
-		dev_err(chip_info->dev,
-			"DATA Size is configured incorrectly\n");
-		return -EINVAL;
-	}
 	if ((chip_info->com_mode != INTERRUPT_TRANSFER)
 	    && (chip_info->com_mode != DMA_TRANSFER)
 	    && (chip_info->com_mode != POLLING_TRANSFER)) {
@@ -1316,20 +1292,6 @@  static int verify_controller_parameters(struct pl022 *pl022,
 			"TX FIFO Trigger Level is configured incorrectly\n");
 		return -EINVAL;
 	}
-	if (chip_info->iface == SSP_INTERFACE_MOTOROLA_SPI) {
-		if ((chip_info->clk_phase != SSP_CLK_FIRST_EDGE)
-		    && (chip_info->clk_phase != SSP_CLK_SECOND_EDGE)) {
-			dev_err(chip_info->dev,
-				"Clock Phase is configured incorrectly\n");
-			return -EINVAL;
-		}
-		if ((chip_info->clk_pol != SSP_CLK_POL_IDLE_LOW)
-		    && (chip_info->clk_pol != SSP_CLK_POL_IDLE_HIGH)) {
-			dev_err(chip_info->dev,
-				"Clock Polarity is configured incorrectly\n");
-			return -EINVAL;
-		}
-	}
 	if (chip_info->iface == SSP_INTERFACE_NATIONAL_MICROWIRE) {
 		if ((chip_info->ctrl_len < SSP_BITS_4)
 		    || (chip_info->ctrl_len > SSP_BITS_32)) {
@@ -1494,23 +1456,14 @@  static int process_dma_info(struct pl022_config_chip *chip_info,
  * controller hardware here, that is not done until the actual transfer
  * commence.
  */
-
-/* FIXME: JUST GUESSING the spi->mode bits understood by this driver */
-#define MODEBITS	(SPI_CPOL | SPI_CPHA | SPI_CS_HIGH \
-			| SPI_LSB_FIRST | SPI_LOOP)
-
 static int pl022_setup(struct spi_device *spi)
 {
 	struct pl022_config_chip *chip_info;
 	struct chip_data *chip;
 	int status = 0;
 	struct pl022 *pl022 = spi_master_get_devdata(spi->master);
-
-	if (spi->mode & ~MODEBITS) {
-		dev_dbg(&spi->dev, "unsupported mode bits %x\n",
-			spi->mode & ~MODEBITS);
-		return -EINVAL;
-	}
+	unsigned int bits = spi->bits_per_word;
+	u32 tmp;
 
 	if (!spi->max_speed_hz)
 		return -EINVAL;
@@ -1555,18 +1508,12 @@  static int pl022_setup(struct spi_device *spi)
 		 * Set controller data default values:
 		 * Polling is supported by default
 		 */
-		chip_info->lbm = LOOPBACK_DISABLED;
 		chip_info->com_mode = POLLING_TRANSFER;
 		chip_info->iface = SSP_INTERFACE_MOTOROLA_SPI;
 		chip_info->hierarchy = SSP_SLAVE;
 		chip_info->slave_tx_disable = DO_NOT_DRIVE_TX;
-		chip_info->endian_tx = SSP_TX_LSB;
-		chip_info->endian_rx = SSP_RX_LSB;
-		chip_info->data_size = SSP_DATA_BITS_12;
 		chip_info->rx_lev_trig = SSP_RX_1_OR_MORE_ELEM;
 		chip_info->tx_lev_trig = SSP_TX_1_OR_MORE_EMPTY_LOC;
-		chip_info->clk_phase = SSP_CLK_SECOND_EDGE;
-		chip_info->clk_pol = SSP_CLK_POL_IDLE_LOW;
 		chip_info->ctrl_len = SSP_BITS_8;
 		chip_info->wait_state = SSP_MWIRE_WAIT_ZERO;
 		chip_info->duplex = SSP_MICROWIRE_CHANNEL_FULL_DUPLEX;
@@ -1601,12 +1548,16 @@  static int pl022_setup(struct spi_device *spi)
 	chip->xfer_type = chip_info->com_mode;
 	chip->cs_control = chip_info->cs_control;
 
-	if (chip_info->data_size <= 8) {
-		dev_dbg(&spi->dev, "1 <= n <=8 bits per word\n");
+	if (bits <= 3) {
+		/* PL022 doesn't support less than 4-bits */
+		status = -ENOTSUPP;
+		goto err_config_params;
+	} else if (bits <= 8) {
+		dev_dbg(&spi->dev, "4 <= n <=8 bits per word\n");
 		chip->n_bytes = 1;
 		chip->read = READING_U8;
 		chip->write = WRITING_U8;
-	} else if (chip_info->data_size <= 16) {
+	} else if (bits <= 16) {
 		dev_dbg(&spi->dev, "9 <= n <= 16 bits per word\n");
 		chip->n_bytes = 2;
 		chip->read = READING_U16;
@@ -1623,6 +1574,7 @@  static int pl022_setup(struct spi_device *spi)
 			dev_err(&spi->dev,
 				"a standard pl022 can only handle "
 				"1 <= n <= 16 bit words\n");
+			status = -ENOTSUPP;
 			goto err_config_params;
 		}
 	}
@@ -1656,6 +1608,8 @@  static int pl022_setup(struct spi_device *spi)
 
 	/* Special setup for the ST micro extended control registers */
 	if (pl022->vendor->extended_cr) {
+		u32 etx;
+
 		if (pl022->vendor->pl023) {
 			/* These bits are only in the PL023 */
 			SSP_WRITE_BITS(chip->cr1, chip_info->clkdelay,
@@ -1671,29 +1625,51 @@  static int pl022_setup(struct spi_device *spi)
 			SSP_WRITE_BITS(chip->cr1, chip_info->wait_state,
 				       SSP_CR1_MASK_MWAIT_ST, 6);
 		}
-		SSP_WRITE_BITS(chip->cr0, chip_info->data_size,
+		SSP_WRITE_BITS(chip->cr0, bits - 1,
 			       SSP_CR0_MASK_DSS_ST, 0);
-		SSP_WRITE_BITS(chip->cr1, chip_info->endian_rx,
-			       SSP_CR1_MASK_RENDN_ST, 4);
-		SSP_WRITE_BITS(chip->cr1, chip_info->endian_tx,
-			       SSP_CR1_MASK_TENDN_ST, 5);
+
+		if (spi->mode & SPI_LSB_FIRST) {
+			tmp = SSP_RX_LSB;
+			etx = SSP_TX_LSB;
+		} else {
+			tmp = SSP_RX_MSB;
+			etx = SSP_TX_MSB;
+		}
+		SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_RENDN_ST, 4);
+		SSP_WRITE_BITS(chip->cr1, etx, SSP_CR1_MASK_TENDN_ST, 5);
 		SSP_WRITE_BITS(chip->cr1, chip_info->rx_lev_trig,
 			       SSP_CR1_MASK_RXIFLSEL_ST, 7);
 		SSP_WRITE_BITS(chip->cr1, chip_info->tx_lev_trig,
 			       SSP_CR1_MASK_TXIFLSEL_ST, 10);
 	} else {
-		SSP_WRITE_BITS(chip->cr0, chip_info->data_size,
+		SSP_WRITE_BITS(chip->cr0, bits - 1,
 			       SSP_CR0_MASK_DSS, 0);
 		SSP_WRITE_BITS(chip->cr0, chip_info->iface,
 			       SSP_CR0_MASK_FRF, 4);
 	}
+
 	/* Stuff that is common for all versions */
-	SSP_WRITE_BITS(chip->cr0, chip_info->clk_pol, SSP_CR0_MASK_SPO, 6);
-	SSP_WRITE_BITS(chip->cr0, chip_info->clk_phase, SSP_CR0_MASK_SPH, 7);
+	if (spi->mode & SPI_CPOL)
+		tmp = SSP_CLK_POL_IDLE_HIGH;
+	else
+		tmp = SSP_CLK_POL_IDLE_LOW;
+	SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPO, 6);
+
+	if (spi->mode & SPI_CPHA)
+		tmp = SSP_CLK_SECOND_EDGE;
+	else
+		tmp = SSP_CLK_FIRST_EDGE;
+	SSP_WRITE_BITS(chip->cr0, tmp, SSP_CR0_MASK_SPH, 6);
+
 	SSP_WRITE_BITS(chip->cr0, chip_info->clk_freq.scr, SSP_CR0_MASK_SCR, 8);
 	/* Loopback is available on all versions except PL023 */
-	if (!pl022->vendor->pl023)
-		SSP_WRITE_BITS(chip->cr1, chip_info->lbm, SSP_CR1_MASK_LBM, 0);
+	if (!pl022->vendor->pl023) {
+		if (spi->mode & SPI_LOOP)
+			tmp = LOOPBACK_ENABLED;
+		else
+			tmp = LOOPBACK_DISABLED;
+		SSP_WRITE_BITS(chip->cr1, tmp, SSP_CR1_MASK_LBM, 0);
+	}
 	SSP_WRITE_BITS(chip->cr1, SSP_DISABLED, SSP_CR1_MASK_SSE, 1);
 	SSP_WRITE_BITS(chip->cr1, chip_info->hierarchy, SSP_CR1_MASK_MS, 2);
 	SSP_WRITE_BITS(chip->cr1, chip_info->slave_tx_disable, SSP_CR1_MASK_SOD, 3);
@@ -1702,6 +1678,7 @@  static int pl022_setup(struct spi_device *spi)
 	spi_set_ctldata(spi, chip);
 	return status;
  err_config_params:
+	spi_set_ctldata(spi, NULL);
  err_first_setup:
 	kfree(chip);
 	return status;
@@ -1764,6 +1741,14 @@  pl022_probe(struct amba_device *adev, struct amba_id *id)
 	master->setup = pl022_setup;
 	master->transfer = pl022_transfer;
 
+	/*
+	 * Supports mode 0-3, loopback, and active low CS. Transfers are
+	 * always MS bit first on the original pl022.
+	 */
+	master->mode_bits = SPI_CPOL | SPI_CPHA | SPI_CS_HIGH | SPI_LOOP;
+	if (pl022->vendor->extended_cr)
+		master->mode_bits |= SPI_LSB_FIRST;
+
 	dev_dbg(&adev->dev, "BUSNO: %d\n", master->bus_num);
 
 	status = amba_request_regions(adev, NULL);