@@ -123,6 +123,13 @@ config SPI_BUTTERFLY
inexpensive battery powered microcontroller evaluation board.
This same cable can be used to flash new firmware.
+config SPI_CLPS711X
+ tristate "CLPS711X host SPI controller"
+ depends on ARCH_CLPS711X
+ help
+ This enables dedicated general purpose SPI/Microwire1-compatible
+ master mode interface (SSI1) for CLPS711X-based CPUs.
+
config SPI_COLDFIRE_QSPI
tristate "Freescale Coldfire QSPI controller"
depends on (M520x || M523x || M5249 || M525x || M527x || M528x || M532x)
@@ -19,6 +19,7 @@ obj-$(CONFIG_SPI_BFIN5XX) += spi-bfin5xx.o
obj-$(CONFIG_SPI_BFIN_SPORT) += spi-bfin-sport.o
obj-$(CONFIG_SPI_BITBANG) += spi-bitbang.o
obj-$(CONFIG_SPI_BUTTERFLY) += spi-butterfly.o
+obj-$(CONFIG_SPI_CLPS711X) += spi-clps711x.o
obj-$(CONFIG_SPI_COLDFIRE_QSPI) += spi-coldfire-qspi.o
obj-$(CONFIG_SPI_DAVINCI) += spi-davinci.o
obj-$(CONFIG_SPI_DESIGNWARE) += spi-dw.o
new file mode 100644
@@ -0,0 +1,296 @@
+/*
+ * CLPS711X SPI bus driver
+ *
+ * Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/init.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/platform_device.h>
+#include <linux/spi/spi.h>
+#include <linux/platform_data/spi-clps711x.h>
+
+#include <mach/hardware.h>
+
+#define DRIVER_NAME "spi-clps711x"
+
+struct spi_clps711x_data {
+ struct completion done;
+
+ struct clk *spi_clk;
+ u32 max_speed_hz;
+
+ u8 *tx_buf;
+ u8 *rx_buf;
+ int count;
+ int len;
+
+ int chipselect[0];
+};
+
+static int spi_clps711x_setup(struct spi_device *spi)
+{
+ struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
+
+ if (spi->bits_per_word != 8) {
+ dev_err(&spi->dev, "Unsupported master bus width %i\n",
+ spi->bits_per_word);
+ return -EINVAL;
+ }
+
+ /* We are expect that SPI-device is not selected */
+ gpio_direction_output(hw->chipselect[spi->chip_select],
+ !(spi->mode & SPI_CS_HIGH));
+
+ return 0;
+}
+
+static void spi_clps711x_setup_mode(struct spi_device *spi)
+{
+ /* Setup edge for transfer */
+ if (spi->mode & SPI_CPHA)
+ clps_writew(clps_readw(SYSCON3) | SYSCON3_ADCCKNSEN, SYSCON3);
+ else
+ clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCKNSEN, SYSCON3);
+}
+
+static int spi_clps711x_setup_xfer(struct spi_device *spi,
+ struct spi_transfer *xfer)
+{
+ u32 speed = xfer->speed_hz ? : spi->max_speed_hz;
+ u8 bpw = xfer->bits_per_word ? : spi->bits_per_word;
+ struct spi_clps711x_data *hw = spi_master_get_devdata(spi->master);
+
+ if (bpw != 8) {
+ dev_err(&spi->dev, "Unsupported master bus width %i\n", bpw);
+ return -EINVAL;
+ }
+
+ /* Setup SPI frequency divider */
+ if (!speed || (speed >= hw->max_speed_hz))
+ clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
+ SYSCON1_ADCKSEL(3), SYSCON1);
+ else if (speed >= (hw->max_speed_hz / 2))
+ clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
+ SYSCON1_ADCKSEL(2), SYSCON1);
+ else if (speed >= (hw->max_speed_hz / 8))
+ clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
+ SYSCON1_ADCKSEL(1), SYSCON1);
+ else
+ clps_writel((clps_readl(SYSCON1) & ~SYSCON1_ADCKSEL_MASK) |
+ SYSCON1_ADCKSEL(0), SYSCON1);
+
+ return 0;
+}
+
+static int spi_clps711x_transfer_one_message(struct spi_master *master,
+ struct spi_message *msg)
+{
+ struct spi_clps711x_data *hw = spi_master_get_devdata(master);
+ struct spi_transfer *xfer;
+ int status = 0, cs = hw->chipselect[msg->spi->chip_select];
+ u32 data;
+
+ spi_clps711x_setup_mode(msg->spi);
+
+ list_for_each_entry(xfer, &msg->transfers, transfer_list) {
+ if (spi_clps711x_setup_xfer(msg->spi, xfer)) {
+ status = -EINVAL;
+ goto out_xfr;
+ }
+
+ gpio_set_value(cs, !!(msg->spi->mode & SPI_CS_HIGH));
+
+ INIT_COMPLETION(hw->done);
+
+ hw->count = 0;
+ hw->len = xfer->len;
+ hw->tx_buf = (u8 *)xfer->tx_buf;
+ hw->rx_buf = (u8 *)xfer->rx_buf;
+
+ /* Initiate transfer */
+ data = hw->tx_buf ? hw->tx_buf[hw->count] : 0;
+ clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
+
+ wait_for_completion(&hw->done);
+
+ if (xfer->delay_usecs)
+ udelay(xfer->delay_usecs);
+
+ if (xfer->cs_change ||
+ list_is_last(&xfer->transfer_list, &msg->transfers))
+ gpio_set_value(cs, !(msg->spi->mode & SPI_CS_HIGH));
+
+ msg->actual_length += xfer->len;
+ }
+
+out_xfr:
+ msg->status = status;
+ spi_finalize_current_message(master);
+
+ return 0;
+}
+
+static irqreturn_t spi_clps711x_isr(int irq, void *dev_id)
+{
+ struct spi_clps711x_data *hw = (struct spi_clps711x_data *)dev_id;
+ u32 data;
+
+ /* Handle RX */
+ data = clps_readb(SYNCIO);
+ if (hw->rx_buf)
+ hw->rx_buf[hw->count] = (u8)data;
+
+ hw->count++;
+
+ /* Handle TX */
+ if (hw->count < hw->len) {
+ data = hw->tx_buf ? hw->tx_buf[hw->count] : 0;
+ clps_writel(data | SYNCIO_FRMLEN(8) | SYNCIO_TXFRMEN, SYNCIO);
+ } else
+ complete(&hw->done);
+
+ return IRQ_HANDLED;
+}
+
+static int __devinit spi_clps711x_probe(struct platform_device *pdev)
+{
+ int i, ret;
+ struct spi_master *master;
+ struct spi_clps711x_data *hw;
+ struct spi_clps711x_pdata *pdata = dev_get_platdata(&pdev->dev);
+
+ if (!pdata) {
+ dev_err(&pdev->dev, "No platform data supplied\n");
+ return -EINVAL;
+ }
+
+ if (pdata->num_chipselect < 1) {
+ dev_err(&pdev->dev, "At least one CS must be defined\n");
+ return -EINVAL;
+ }
+
+ master = spi_alloc_master(&pdev->dev,
+ sizeof(struct spi_clps711x_data) +
+ sizeof(int) * pdata->num_chipselect);
+ if (!master) {
+ dev_err(&pdev->dev, "SPI allocating memory error\n");
+ return -ENOMEM;
+ }
+
+ master->bus_num = pdev->id;
+ master->mode_bits = SPI_CPHA | SPI_CS_HIGH;
+ master->num_chipselect = pdata->num_chipselect;
+ master->setup = spi_clps711x_setup;
+ master->transfer_one_message = spi_clps711x_transfer_one_message;
+
+ hw = spi_master_get_devdata(master);
+
+ for (i = 0; i < master->num_chipselect; i++) {
+ hw->chipselect[i] = pdata->chipselect[i];
+ if (!gpio_is_valid(hw->chipselect[i])) {
+ dev_err(&pdev->dev, "Invalid CS GPIO %i\n", i);
+ ret = -EINVAL;
+ goto err_out;
+ }
+ if (gpio_request(hw->chipselect[i], DRIVER_NAME)) {
+ dev_err(&pdev->dev, "Can't get CS GPIO %i\n", i);
+ ret = -EINVAL;
+ goto err_out;
+ }
+ }
+
+ hw->spi_clk = devm_clk_get(&pdev->dev, "spi");
+ if (IS_ERR(hw->spi_clk)) {
+ dev_err(&pdev->dev, "Can't get clocks\n");
+ ret = PTR_ERR(hw->spi_clk);
+ goto err_out;
+ }
+ hw->max_speed_hz = clk_get_rate(hw->spi_clk);
+
+ init_completion(&hw->done);
+ platform_set_drvdata(pdev, master);
+
+ /* Disable extended mode due hardware problems */
+ clps_writew(clps_readw(SYSCON3) & ~SYSCON3_ADCCON, SYSCON3);
+
+ /* Clear possible pending interrupt */
+ clps_readl(SYNCIO);
+
+ ret = devm_request_irq(&pdev->dev, IRQ_SSEOTI, spi_clps711x_isr, 0,
+ dev_name(&pdev->dev), hw);
+ if (ret) {
+ dev_err(&pdev->dev, "Can't request IRQ\n");
+ clk_put(hw->spi_clk);
+ goto clk_out;
+ }
+
+ ret = spi_register_master(master);
+ if (!ret) {
+ dev_info(&pdev->dev,
+ "SPI bus driver initialized. Master clock %u Hz\n",
+ hw->max_speed_hz);
+ return 0;
+ }
+
+ dev_err(&pdev->dev, "Failed to register master\n");
+ devm_free_irq(&pdev->dev, IRQ_SSEOTI, hw);
+
+clk_out:
+ devm_clk_put(&pdev->dev, hw->spi_clk);
+
+err_out:
+ while (--i >= 0)
+ if (gpio_is_valid(hw->chipselect[i]))
+ gpio_free(hw->chipselect[i]);
+
+ platform_set_drvdata(pdev, NULL);
+ spi_master_put(master);
+ kfree(master);
+
+ return ret;
+}
+
+static int __devexit spi_clps711x_remove(struct platform_device *pdev)
+{
+ int i;
+ struct spi_master *master = platform_get_drvdata(pdev);
+ struct spi_clps711x_data *hw = spi_master_get_devdata(master);
+
+ devm_free_irq(&pdev->dev, IRQ_SSEOTI, hw);
+
+ for (i = 0; i < master->num_chipselect; i++)
+ if (gpio_is_valid(hw->chipselect[i]))
+ gpio_free(hw->chipselect[i]);
+
+ devm_clk_put(&pdev->dev, hw->spi_clk);
+ platform_set_drvdata(pdev, NULL);
+ spi_unregister_master(master);
+ kfree(master);
+
+ return 0;
+}
+
+static struct platform_driver clps711x_spi_driver = {
+ .driver = {
+ .name = DRIVER_NAME,
+ .owner = THIS_MODULE,
+ },
+ .probe = spi_clps711x_probe,
+ .remove = __devexit_p(spi_clps711x_remove),
+};
+module_platform_driver(clps711x_spi_driver);
+
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Alexander Shiyan <shc_work@mail.ru>");
+MODULE_DESCRIPTION("CLPS711X SPI bus driver");
new file mode 100644
@@ -0,0 +1,21 @@
+/*
+ * CLPS711X SPI bus driver definitions
+ *
+ * Copyright (C) 2012 Alexander Shiyan <shc_work@mail.ru>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ */
+
+#ifndef ____LINUX_PLATFORM_DATA_SPI_CLPS711X_H
+#define ____LINUX_PLATFORM_DATA_SPI_CLPS711X_H
+
+/* Board specific platform_data */
+struct spi_clps711x_pdata {
+ int *chipselect; /* Array of GPIO-numbers */
+ int num_chipselect; /* Total count of GPIOs */
+};
+
+#endif
This patch add new driver for CLPS711X SPI master controller. Due to platform limitations driver supports only 8 bit transfer mode. Chip select control is handled via GPIO. Signed-off-by: Alexander Shiyan <shc_work@mail.ru> --- drivers/spi/Kconfig | 7 + drivers/spi/Makefile | 1 + drivers/spi/spi-clps711x.c | 296 ++++++++++++++++++++++++++++ include/linux/platform_data/spi-clps711x.h | 21 ++ 4 files changed, 325 insertions(+), 0 deletions(-) create mode 100644 drivers/spi/spi-clps711x.c create mode 100644 include/linux/platform_data/spi-clps711x.h