| Message ID | 1392109008-29941-1-git-send-email-geert@linux-m68k.org (mailing list archive) |
|---|---|
| State | Not Applicable |
| Headers | show |
Hi Morimoto-san, could you test this series as Geert does not have access to a bockw board? On Tue, Feb 11, 2014 at 09:56:47AM +0100, Geert Uytterhoeven wrote: > From: Geert Uytterhoeven <geert+renesas@linux-m68k.org> > > Binding documentation: > - Add future-proof "renesas,hspi-<soctype>" compatible values, > - Add "interrupt-parent", "#address-cells" and "#size-cells" properties, > - Add reference to pinctrl documentation, > - Add example bindings. > > r8a7778 and r8a7779 dtsi: > - Add "renesas,hspi-r8a7778" resp. "renesas,hspi-r8a7779" compatible > values, > - Correct reference to parent interrupt controller > (use "interrupt-parent" instead of "interrupt-controller"), > - Add missing "#address-cells" and "#size-cells" properties, which are > needed when populating the SPI buses. > > Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> > Cc: Mark Brown <broonie@linaro.org> > --- > Untested due to lack of hardware > > Documentation/devicetree/bindings/spi/sh-hspi.txt | 27 ++++++++++++++++++--- > arch/arm/boot/dts/r8a7778.dtsi | 18 +++++++++----- > arch/arm/boot/dts/r8a7779.dtsi | 18 +++++++++----- > 3 files changed, 48 insertions(+), 15 deletions(-) > > diff --git a/Documentation/devicetree/bindings/spi/sh-hspi.txt b/Documentation/devicetree/bindings/spi/sh-hspi.txt > index 30b57b1c8a13..d43080eb6b3a 100644 > --- a/Documentation/devicetree/bindings/spi/sh-hspi.txt > +++ b/Documentation/devicetree/bindings/spi/sh-hspi.txt > @@ -1,7 +1,28 @@ > Renesas HSPI. > > Required properties: > -- compatible : "renesas,hspi" > -- reg : Offset and length of the register set for the device > -- interrupts : interrupt line used by HSPI > +- compatible : "renesas,hspi-<soctype>", "renesas,hspi" as fallback. > + Examples of valid soctypes are "r8a7778" (R-Car M1), > + and "r8a7779" (R-Car H1) > +- reg : Offset and length of the register set for the device > +- interrupt-parent : The phandle for the interrupt controller that > + services interrupts for this device > +- interrupts : Interrupt specifier > +- #address-cells : Must be <1> > +- #size-cells : Must be <0> > + > +Pinctrl properties might be needed, too. See > +Documentation/devicetree/bindings/pinctrl/renesas,*. > + > +Example: > + > + hspi0: spi@fffc7000 { > + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; > + reg = <0xfffc7000 0x18>; > + interrupt-parent = <&gic>; > + interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > > diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi > index 85c5b3b99f5e..3c6fab5c9702 100644 > --- a/arch/arm/boot/dts/r8a7778.dtsi > +++ b/arch/arm/boot/dts/r8a7778.dtsi > @@ -204,26 +204,32 @@ > }; > > hspi0: spi@fffc7000 { > - compatible = "renesas,hspi"; > + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; > reg = <0xfffc7000 0x18>; > - interrupt-controller = <&gic>; > + interrupt-parent = <&gic>; > interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > status = "disabled"; > }; > > hspi1: spi@fffc8000 { > - compatible = "renesas,hspi"; > + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; > reg = <0xfffc8000 0x18>; > - interrupt-controller = <&gic>; > + interrupt-parent = <&gic>; > interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > status = "disabled"; > }; > > hspi2: spi@fffc6000 { > - compatible = "renesas,hspi"; > + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; > reg = <0xfffc6000 0x18>; > - interrupt-controller = <&gic>; > + interrupt-parent = <&gic>; > interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > status = "disabled"; > }; > }; > diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi > index d0561d4c7c46..8b1a336ee401 100644 > --- a/arch/arm/boot/dts/r8a7779.dtsi > +++ b/arch/arm/boot/dts/r8a7779.dtsi > @@ -256,26 +256,32 @@ > }; > > hspi0: spi@fffc7000 { > - compatible = "renesas,hspi"; > + compatible = "renesas,hspi-r8a7779", "renesas,hspi"; > reg = <0xfffc7000 0x18>; > - interrupt-controller = <&gic>; > + interrupt-parent = <&gic>; > interrupts = <0 73 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > status = "disabled"; > }; > > hspi1: spi@fffc8000 { > - compatible = "renesas,hspi"; > + compatible = "renesas,hspi-r8a7779", "renesas,hspi"; > reg = <0xfffc8000 0x18>; > - interrupt-controller = <&gic>; > + interrupt-parent = <&gic>; > interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > status = "disabled"; > }; > > hspi2: spi@fffc6000 { > - compatible = "renesas,hspi"; > + compatible = "renesas,hspi-r8a7779", "renesas,hspi"; > reg = <0xfffc6000 0x18>; > - interrupt-controller = <&gic>; > + interrupt-parent = <&gic>; > interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>; > + #address-cells = <1>; > + #size-cells = <0>; > status = "disabled"; > }; > }; > -- > 1.7.9.5 > -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Simon, Geert Cc Mark > could you test this series as Geert does not have access to a bockw board? > > On Tue, Feb 11, 2014 at 09:56:47AM +0100, Geert Uytterhoeven wrote: > > From: Geert Uytterhoeven <geert+renesas@linux-m68k.org> > > > > Binding documentation: > > - Add future-proof "renesas,hspi-<soctype>" compatible values, > > - Add "interrupt-parent", "#address-cells" and "#size-cells" properties, > > - Add reference to pinctrl documentation, > > - Add example bindings. > > > > r8a7778 and r8a7779 dtsi: > > - Add "renesas,hspi-r8a7778" resp. "renesas,hspi-r8a7779" compatible > > values, > > - Correct reference to parent interrupt controller > > (use "interrupt-parent" instead of "interrupt-controller"), > > - Add missing "#address-cells" and "#size-cells" properties, which are > > needed when populating the SPI buses. > > > > Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> > > Cc: Mark Brown <broonie@linaro.org> > > --- I tested this patch, and it works well. But there are some notes 1) m25p80 driver DT support seems strange ?? ${LINUX}/Documentation/devicetree/bindings/mtd/m25p80.txt has explain about DT of m25p80 driver, but, ${LINUX}/drivers/mtd/devices/m25p80.c doesn't have driver :: of_match_table. but, it is using of_property_read_bool() on probe. Is it out-of-tree support ?? I'm not sure, anyway, m25p80 driver didn't probe. So, I quick-hacked this issue in my local environment. 2) it needs Geert's this patch Subject: [PATCH] mtd: m25p80: add support for the Spansion s25fl008k chip Date: Tue, 11 Feb 2014 09:51:18 +0100 Kernel will hung-up without this patch For HSPI / BockW point of view Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Morimoto-san, On Thu, Feb 13, 2014 at 8:11 AM, Kuninori Morimoto <kuninori.morimoto.gx@gmail.com> wrote: >> could you test this series as Geert does not have access to a bockw board? >> >> On Tue, Feb 11, 2014 at 09:56:47AM +0100, Geert Uytterhoeven wrote: >> > From: Geert Uytterhoeven <geert+renesas@linux-m68k.org> >> > >> > Binding documentation: >> > - Add future-proof "renesas,hspi-<soctype>" compatible values, >> > - Add "interrupt-parent", "#address-cells" and "#size-cells" properties, >> > - Add reference to pinctrl documentation, >> > - Add example bindings. >> > >> > r8a7778 and r8a7779 dtsi: >> > - Add "renesas,hspi-r8a7778" resp. "renesas,hspi-r8a7779" compatible >> > values, >> > - Correct reference to parent interrupt controller >> > (use "interrupt-parent" instead of "interrupt-controller"), >> > - Add missing "#address-cells" and "#size-cells" properties, which are >> > needed when populating the SPI buses. >> > >> > Signed-off-by: Geert Uytterhoeven <geert+renesas@linux-m68k.org> >> > Cc: Mark Brown <broonie@linaro.org> >> > --- > > I tested this patch, and it works well. > But there are some notes > > 1) m25p80 driver DT support seems strange ?? > > ${LINUX}/Documentation/devicetree/bindings/mtd/m25p80.txt > has explain about DT of m25p80 driver, but, > ${LINUX}/drivers/mtd/devices/m25p80.c > doesn't have driver :: of_match_table. > but, it is using of_property_read_bool() on probe. > Is it out-of-tree support ?? I'm not sure, > anyway, m25p80 driver didn't probe. It probes based on the values in m25p_ids[]. See drivers/of/base.c:of_modalias_node(): * Based on the value of the compatible property, this routine will attempt * to choose an appropriate modalias value for a particular device tree node. * It does this by stripping the manufacturer prefix (as delimited by a ',') * from the first entry in the compatible list property. Which is used by drivers/spi/spi.c:of_register_spi_devices(). > So, I quick-hacked this issue in my local environment. Was there anything else you needed to do, besides adding support for s25fl008k to m25p80.c? > 2) it needs Geert's this patch > > Subject: [PATCH] mtd: m25p80: add support for the Spansion s25fl008k chip > Date: Tue, 11 Feb 2014 09:51:18 +0100 > > Kernel will hung-up without this patch Hang up? Not just ignoring the device? > For HSPI / BockW point of view > > Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Thanks! Gr{oetje,eeting}s, Geert -- Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org In personal conversations with technical people, I call myself a hacker. But when I'm talking to journalists I just say "programmer" or something like that. -- Linus Torvalds -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Geert CC Simon Thank you for your help > * Based on the value of the compatible property, this routine will attempt > * to choose an appropriate modalias value for a particular device tree node. > * It does this by stripping the manufacturer prefix (as delimited by a ',') > * from the first entry in the compatible list property. > > Which is used by drivers/spi/spi.c:of_register_spi_devices(). > > > So, I quick-hacked this issue in my local environment. > > Was there anything else you needed to do, besides adding support for > s25fl008k to m25p80.c? I re-tested cleanly this patch. Yes, indeed, my local-hack was not needed. It was my fault. > > 2) it needs Geert's this patch > > > > Subject: [PATCH] mtd: m25p80: add support for the Spansion s25fl008k chip > > Date: Tue, 11 Feb 2014 09:51:18 +0100 > > > > Kernel will hung-up without this patch > > Hang up? Not just ignoring the device? It works without Hang-up in my re-test now. My previous test seems something wrong. Thank you Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com> Best regards --- Kuninori Morimoto -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
diff --git a/Documentation/devicetree/bindings/spi/sh-hspi.txt b/Documentation/devicetree/bindings/spi/sh-hspi.txt index 30b57b1c8a13..d43080eb6b3a 100644 --- a/Documentation/devicetree/bindings/spi/sh-hspi.txt +++ b/Documentation/devicetree/bindings/spi/sh-hspi.txt @@ -1,7 +1,28 @@ Renesas HSPI. Required properties: -- compatible : "renesas,hspi" -- reg : Offset and length of the register set for the device -- interrupts : interrupt line used by HSPI +- compatible : "renesas,hspi-<soctype>", "renesas,hspi" as fallback. + Examples of valid soctypes are "r8a7778" (R-Car M1), + and "r8a7779" (R-Car H1) +- reg : Offset and length of the register set for the device +- interrupt-parent : The phandle for the interrupt controller that + services interrupts for this device +- interrupts : Interrupt specifier +- #address-cells : Must be <1> +- #size-cells : Must be <0> + +Pinctrl properties might be needed, too. See +Documentation/devicetree/bindings/pinctrl/renesas,*. + +Example: + + hspi0: spi@fffc7000 { + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; + reg = <0xfffc7000 0x18>; + interrupt-parent = <&gic>; + interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; diff --git a/arch/arm/boot/dts/r8a7778.dtsi b/arch/arm/boot/dts/r8a7778.dtsi index 85c5b3b99f5e..3c6fab5c9702 100644 --- a/arch/arm/boot/dts/r8a7778.dtsi +++ b/arch/arm/boot/dts/r8a7778.dtsi @@ -204,26 +204,32 @@ }; hspi0: spi@fffc7000 { - compatible = "renesas,hspi"; + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; reg = <0xfffc7000 0x18>; - interrupt-controller = <&gic>; + interrupt-parent = <&gic>; interrupts = <0 63 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; hspi1: spi@fffc8000 { - compatible = "renesas,hspi"; + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; reg = <0xfffc8000 0x18>; - interrupt-controller = <&gic>; + interrupt-parent = <&gic>; interrupts = <0 84 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; hspi2: spi@fffc6000 { - compatible = "renesas,hspi"; + compatible = "renesas,hspi-r8a7778", "renesas,hspi"; reg = <0xfffc6000 0x18>; - interrupt-controller = <&gic>; + interrupt-parent = <&gic>; interrupts = <0 85 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/r8a7779.dtsi b/arch/arm/boot/dts/r8a7779.dtsi index d0561d4c7c46..8b1a336ee401 100644 --- a/arch/arm/boot/dts/r8a7779.dtsi +++ b/arch/arm/boot/dts/r8a7779.dtsi @@ -256,26 +256,32 @@ }; hspi0: spi@fffc7000 { - compatible = "renesas,hspi"; + compatible = "renesas,hspi-r8a7779", "renesas,hspi"; reg = <0xfffc7000 0x18>; - interrupt-controller = <&gic>; + interrupt-parent = <&gic>; interrupts = <0 73 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; hspi1: spi@fffc8000 { - compatible = "renesas,hspi"; + compatible = "renesas,hspi-r8a7779", "renesas,hspi"; reg = <0xfffc8000 0x18>; - interrupt-controller = <&gic>; + interrupt-parent = <&gic>; interrupts = <0 74 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; hspi2: spi@fffc6000 { - compatible = "renesas,hspi"; + compatible = "renesas,hspi-r8a7779", "renesas,hspi"; reg = <0xfffc6000 0x18>; - interrupt-controller = <&gic>; + interrupt-parent = <&gic>; interrupts = <0 75 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; status = "disabled"; }; };