diff mbox

[v3,2/8] spi: sun4i: add DMA support

Message ID 1407183002-29420-3-git-send-email-emilio@elopez.com.ar (mailing list archive)
State New, archived
Headers show

Commit Message

Emilio López Aug. 4, 2014, 8:09 p.m. UTC
This patch adds support for 64 byte or bigger transfers on the
sun4i SPI controller. Said transfers will be performed via DMA.

Signed-off-by: Emilio López <emilio@elopez.com.ar>
---

Changes from v2:
 * Fix commit message

Changes from v1:
 * remove 64 byte limitation on transfers
 * wrap stuff so it fits better in 80 cols

 drivers/spi/spi-sun4i.c | 155 ++++++++++++++++++++++++++++++++++++++++++++----
 1 file changed, 144 insertions(+), 11 deletions(-)

Comments

Maxime Ripard Aug. 5, 2014, 8:23 p.m. UTC | #1
Hi,

On Mon, Aug 04, 2014 at 05:09:56PM -0300, Emilio López wrote:
> +	if (sun4i_spi_can_dma(master, spi, tfr)) {
> +		dev_dbg(&sspi->master->dev, "Using DMA mode for transfer\n");
> +
> +		if (sspi->tx_buf) {
> +			desc_tx = dmaengine_prep_slave_sg(sspi->tx_dma_chan,
> +					tfr->tx_sg.sgl, tfr->tx_sg.nents,
> +					DMA_TO_DEVICE,
> +					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
> +			if (!desc_tx) {
> +				dev_err(&sspi->master->dev,
> +					"Couldn't prepare dma slave\n");
> +				return -EIO;
> +			}
> +
> +			dmaengine_submit(desc_tx);
> +		}
> +
> +		if (sspi->rx_buf) {
> +			desc_rx = dmaengine_prep_slave_sg(sspi->rx_dma_chan,
> +					tfr->rx_sg.sgl, tfr->rx_sg.nents,
> +					DMA_FROM_DEVICE,
> +					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
> +			if (!desc_rx) {
> +				dev_err(&sspi->master->dev,
> +					"Couldn't prepare dma slave\n");
> +				return -EIO;
> +			}
> +
> +			dmaengine_submit(desc_rx);
> +		}
> +
> +		/* Enable DMA requests */
> +		reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
> +		sun4i_spi_write(sspi, SUN4I_CTL_REG,
> +				reg | SUN4I_CTL_DMAMC_DEDICATED);
> +		sun4i_spi_write(sspi, SUN4I_DMA_CTL_REG,
> +				SUN4I_DMA_CTL_TF_NOT_FULL |
> +				SUN4I_DMA_CTL_RF_READY);
> +
> +		dma_async_issue_pending(sspi->rx_dma_chan);
> +		dma_async_issue_pending(sspi->tx_dma_chan);

I guess the DMA levels setup and the issue pending calls could be
moved to the if statements above about wether the RX and TX buffers
are here or not.

> +	} else {
> +		dev_dbg(&sspi->master->dev, "Using PIO mode for transfer\n");
> +
> +		/* Disable DMA requests */
> +		reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
> +		sun4i_spi_write(sspi, SUN4I_CTL_REG,
> +				reg & ~SUN4I_CTL_DMAMC_DEDICATED);
> +		sun4i_spi_write(sspi, SUN4I_DMA_CTL_REG, 0);
> +
> +		/* Fill the TX FIFO */
> +		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
> +	}
> +
>  	/* Start the transfer */
>  	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
>  	sun4i_spi_write(sspi, SUN4I_CTL_REG, reg | SUN4I_CTL_XCH);
> @@ -286,7 +359,12 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
>  		goto out;
>  	}
>  
> -	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
> +	if (sun4i_spi_can_dma(master, spi, tfr) && desc_rx) {
> +		/* The receive transfer should be the last one to finish */
> +		dma_wait_for_async_tx(desc_rx);
> +	} else {
> +		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
> +	}
>  
>  out:
>  	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
> @@ -351,6 +429,7 @@ static int sun4i_spi_runtime_suspend(struct device *dev)
>  
>  static int sun4i_spi_probe(struct platform_device *pdev)
>  {
> +	struct dma_slave_config dma_sconfig;
>  	struct spi_master *master;
>  	struct sun4i_spi *sspi;
>  	struct resource	*res;
> @@ -386,7 +465,10 @@ static int sun4i_spi_probe(struct platform_device *pdev)
>  		goto err_free_master;
>  	}
>  
> +	init_completion(&sspi->done);
>  	sspi->master = master;
> +	master->can_dma = sun4i_spi_can_dma;
> +	master->prepare_message = sun4i_spi_prepare_message;
>  	master->set_cs = sun4i_spi_set_cs;
>  	master->transfer_one = sun4i_spi_transfer_one;
>  	master->num_chipselect = 4;
> @@ -409,7 +491,45 @@ static int sun4i_spi_probe(struct platform_device *pdev)
>  		goto err_free_master;
>  	}
>  
> -	init_completion(&sspi->done);
> +	sspi->tx_dma_chan = dma_request_slave_channel_reason(&pdev->dev, "tx");
> +	if (IS_ERR(sspi->tx_dma_chan)) {
> +		dev_err(&pdev->dev, "Unable to acquire DMA channel TX\n");
> +		ret = PTR_ERR(sspi->tx_dma_chan);
> +		goto err_free_master;
> +	}
> +
> +	dma_sconfig.direction = DMA_MEM_TO_DEV;
> +	dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> +	dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> +	dma_sconfig.dst_addr = res->start + SUN4I_TXDATA_REG;
> +	dma_sconfig.src_maxburst = 1;
> +	dma_sconfig.dst_maxburst = 1;
> +
> +	ret = dmaengine_slave_config(sspi->tx_dma_chan, &dma_sconfig);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Unable to configure TX DMA slave\n");
> +		goto err_tx_dma_release;
> +	}
> +
> +	sspi->rx_dma_chan = dma_request_slave_channel_reason(&pdev->dev, "rx");
> +	if (IS_ERR(sspi->rx_dma_chan)) {
> +		dev_err(&pdev->dev, "Unable to acquire DMA channel RX\n");
> +		ret = PTR_ERR(sspi->rx_dma_chan);
> +		goto err_tx_dma_release;
> +	}
> +
> +	dma_sconfig.direction = DMA_DEV_TO_MEM;
> +	dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> +	dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
> +	dma_sconfig.src_addr = res->start + SUN4I_RXDATA_REG;
> +	dma_sconfig.src_maxburst = 1;
> +	dma_sconfig.dst_maxburst = 1;
> +
> +	ret = dmaengine_slave_config(sspi->rx_dma_chan, &dma_sconfig);
> +	if (ret) {
> +		dev_err(&pdev->dev, "Unable to configure RX DMA slave\n");
> +		goto err_rx_dma_release;
> +	}
>  
>  	/*
>  	 * This wake-up/shutdown pattern is to be able to have the
> @@ -418,7 +538,7 @@ static int sun4i_spi_probe(struct platform_device *pdev)
>  	ret = sun4i_spi_runtime_resume(&pdev->dev);
>  	if (ret) {
>  		dev_err(&pdev->dev, "Couldn't resume the device\n");
> -		goto err_free_master;
> +		goto err_rx_dma_release;
>  	}
>  
>  	pm_runtime_set_active(&pdev->dev);
> @@ -436,6 +556,10 @@ static int sun4i_spi_probe(struct platform_device *pdev)
>  err_pm_disable:
>  	pm_runtime_disable(&pdev->dev);
>  	sun4i_spi_runtime_suspend(&pdev->dev);
> +err_rx_dma_release:
> +	dma_release_channel(sspi->rx_dma_chan);
> +err_tx_dma_release:
> +	dma_release_channel(sspi->tx_dma_chan);
>  err_free_master:
>  	spi_master_put(master);
>  	return ret;
> @@ -443,8 +567,17 @@ err_free_master:
>  
>  static int sun4i_spi_remove(struct platform_device *pdev)
>  {
> +	struct spi_master *master = platform_get_drvdata(pdev);
> +	struct sun4i_spi *sspi = spi_master_get_devdata(master);
> +
> +	if (pm_runtime_active(&pdev->dev))
> +		sun4i_spi_runtime_suspend(&pdev->dev);
> +

This doesn't really belong in this patch, please send a separate one.

Maxime
Mark Brown Aug. 7, 2014, 5:44 p.m. UTC | #2
On Mon, Aug 04, 2014 at 05:09:56PM -0300, Emilio López wrote:

> +static int sun4i_spi_prepare_message(struct spi_master *master,
> +				     struct spi_message *msg)
> +{
> +	struct sun4i_spi *sspi = spi_master_get_devdata(master);
> +
> +	master->dma_rx = sspi->rx_dma_chan;
> +	master->dma_tx = sspi->tx_dma_chan;
> +
> +	return 0;
> +}

Why is this being done per transfer rather than at probe time?
Emilio López Aug. 7, 2014, 8:37 p.m. UTC | #3
Hi Maxime,

El 05/08/14 a las 17:23, Maxime Ripard escibió:
> Hi,
>
> On Mon, Aug 04, 2014 at 05:09:56PM -0300, Emilio López wrote:
>> +	if (sun4i_spi_can_dma(master, spi, tfr)) {
>> +		dev_dbg(&sspi->master->dev, "Using DMA mode for transfer\n");
>> +
>> +		if (sspi->tx_buf) {
>> +			desc_tx = dmaengine_prep_slave_sg(sspi->tx_dma_chan,
>> +					tfr->tx_sg.sgl, tfr->tx_sg.nents,
>> +					DMA_TO_DEVICE,
>> +					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
>> +			if (!desc_tx) {
>> +				dev_err(&sspi->master->dev,
>> +					"Couldn't prepare dma slave\n");
>> +				return -EIO;
>> +			}
>> +
>> +			dmaengine_submit(desc_tx);
>> +		}
>> +
>> +		if (sspi->rx_buf) {
>> +			desc_rx = dmaengine_prep_slave_sg(sspi->rx_dma_chan,
>> +					tfr->rx_sg.sgl, tfr->rx_sg.nents,
>> +					DMA_FROM_DEVICE,
>> +					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
>> +			if (!desc_rx) {
>> +				dev_err(&sspi->master->dev,
>> +					"Couldn't prepare dma slave\n");
>> +				return -EIO;
>> +			}
>> +
>> +			dmaengine_submit(desc_rx);
>> +		}
>> +
>> +		/* Enable DMA requests */
>> +		reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
>> +		sun4i_spi_write(sspi, SUN4I_CTL_REG,
>> +				reg | SUN4I_CTL_DMAMC_DEDICATED);
>> +		sun4i_spi_write(sspi, SUN4I_DMA_CTL_REG,
>> +				SUN4I_DMA_CTL_TF_NOT_FULL |
>> +				SUN4I_DMA_CTL_RF_READY);
>> +
>> +		dma_async_issue_pending(sspi->rx_dma_chan);
>> +		dma_async_issue_pending(sspi->tx_dma_chan);
>
> I guess the DMA levels setup and the issue pending calls could be
> moved to the if statements above about wether the RX and TX buffers
> are here or not.

Ok, I'll do that.

>> +	} else {
>> +		dev_dbg(&sspi->master->dev, "Using PIO mode for transfer\n");
>> +
>> +		/* Disable DMA requests */
>> +		reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
>> +		sun4i_spi_write(sspi, SUN4I_CTL_REG,
>> +				reg & ~SUN4I_CTL_DMAMC_DEDICATED);
>> +		sun4i_spi_write(sspi, SUN4I_DMA_CTL_REG, 0);
>> +
>> +		/* Fill the TX FIFO */
>> +		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
>> +	}
>> +
>>   	/* Start the transfer */
>>   	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
>>   	sun4i_spi_write(sspi, SUN4I_CTL_REG, reg | SUN4I_CTL_XCH);
>> @@ -286,7 +359,12 @@ static int sun4i_spi_transfer_one(struct spi_master *master,
>>   		goto out;
>>   	}
>>
>> -	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
>> +	if (sun4i_spi_can_dma(master, spi, tfr) && desc_rx) {
>> +		/* The receive transfer should be the last one to finish */
>> +		dma_wait_for_async_tx(desc_rx);
>> +	} else {
>> +		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
>> +	}
>>
>>   out:
>>   	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
>> @@ -351,6 +429,7 @@ static int sun4i_spi_runtime_suspend(struct device *dev)
>>
>>   static int sun4i_spi_probe(struct platform_device *pdev)
>>   {
>> +	struct dma_slave_config dma_sconfig;
>>   	struct spi_master *master;
>>   	struct sun4i_spi *sspi;
>>   	struct resource	*res;
>> @@ -386,7 +465,10 @@ static int sun4i_spi_probe(struct platform_device *pdev)
>>   		goto err_free_master;
>>   	}
>>
>> +	init_completion(&sspi->done);
>>   	sspi->master = master;
>> +	master->can_dma = sun4i_spi_can_dma;
>> +	master->prepare_message = sun4i_spi_prepare_message;
>>   	master->set_cs = sun4i_spi_set_cs;
>>   	master->transfer_one = sun4i_spi_transfer_one;
>>   	master->num_chipselect = 4;
>> @@ -409,7 +491,45 @@ static int sun4i_spi_probe(struct platform_device *pdev)
>>   		goto err_free_master;
>>   	}
>>
>> -	init_completion(&sspi->done);
>> +	sspi->tx_dma_chan = dma_request_slave_channel_reason(&pdev->dev, "tx");
>> +	if (IS_ERR(sspi->tx_dma_chan)) {
>> +		dev_err(&pdev->dev, "Unable to acquire DMA channel TX\n");
>> +		ret = PTR_ERR(sspi->tx_dma_chan);
>> +		goto err_free_master;
>> +	}
>> +
>> +	dma_sconfig.direction = DMA_MEM_TO_DEV;
>> +	dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
>> +	dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
>> +	dma_sconfig.dst_addr = res->start + SUN4I_TXDATA_REG;
>> +	dma_sconfig.src_maxburst = 1;
>> +	dma_sconfig.dst_maxburst = 1;
>> +
>> +	ret = dmaengine_slave_config(sspi->tx_dma_chan, &dma_sconfig);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "Unable to configure TX DMA slave\n");
>> +		goto err_tx_dma_release;
>> +	}
>> +
>> +	sspi->rx_dma_chan = dma_request_slave_channel_reason(&pdev->dev, "rx");
>> +	if (IS_ERR(sspi->rx_dma_chan)) {
>> +		dev_err(&pdev->dev, "Unable to acquire DMA channel RX\n");
>> +		ret = PTR_ERR(sspi->rx_dma_chan);
>> +		goto err_tx_dma_release;
>> +	}
>> +
>> +	dma_sconfig.direction = DMA_DEV_TO_MEM;
>> +	dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
>> +	dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
>> +	dma_sconfig.src_addr = res->start + SUN4I_RXDATA_REG;
>> +	dma_sconfig.src_maxburst = 1;
>> +	dma_sconfig.dst_maxburst = 1;
>> +
>> +	ret = dmaengine_slave_config(sspi->rx_dma_chan, &dma_sconfig);
>> +	if (ret) {
>> +		dev_err(&pdev->dev, "Unable to configure RX DMA slave\n");
>> +		goto err_rx_dma_release;
>> +	}
>>
>>   	/*
>>   	 * This wake-up/shutdown pattern is to be able to have the
>> @@ -418,7 +538,7 @@ static int sun4i_spi_probe(struct platform_device *pdev)
>>   	ret = sun4i_spi_runtime_resume(&pdev->dev);
>>   	if (ret) {
>>   		dev_err(&pdev->dev, "Couldn't resume the device\n");
>> -		goto err_free_master;
>> +		goto err_rx_dma_release;
>>   	}
>>
>>   	pm_runtime_set_active(&pdev->dev);
>> @@ -436,6 +556,10 @@ static int sun4i_spi_probe(struct platform_device *pdev)
>>   err_pm_disable:
>>   	pm_runtime_disable(&pdev->dev);
>>   	sun4i_spi_runtime_suspend(&pdev->dev);
>> +err_rx_dma_release:
>> +	dma_release_channel(sspi->rx_dma_chan);
>> +err_tx_dma_release:
>> +	dma_release_channel(sspi->tx_dma_chan);
>>   err_free_master:
>>   	spi_master_put(master);
>>   	return ret;
>> @@ -443,8 +567,17 @@ err_free_master:
>>
>>   static int sun4i_spi_remove(struct platform_device *pdev)
>>   {
>> +	struct spi_master *master = platform_get_drvdata(pdev);
>> +	struct sun4i_spi *sspi = spi_master_get_devdata(master);
>> +
>> +	if (pm_runtime_active(&pdev->dev))
>> +		sun4i_spi_runtime_suspend(&pdev->dev);
>> +
>
> This doesn't really belong in this patch, please send a separate one.

Sure

Thanks!

Emilio
--
To unsubscribe from this list: send the line "unsubscribe linux-spi" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html
diff mbox

Patch

diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c
index 85204c9..e674100 100644
--- a/drivers/spi/spi-sun4i.c
+++ b/drivers/spi/spi-sun4i.c
@@ -14,6 +14,8 @@ 
 #include <linux/clk.h>
 #include <linux/delay.h>
 #include <linux/device.h>
+#include <linux/dmaengine.h>
+#include <linux/dma-mapping.h>
 #include <linux/interrupt.h>
 #include <linux/io.h>
 #include <linux/module.h>
@@ -34,6 +36,7 @@ 
 #define SUN4I_CTL_CPHA				BIT(2)
 #define SUN4I_CTL_CPOL				BIT(3)
 #define SUN4I_CTL_CS_ACTIVE_LOW			BIT(4)
+#define SUN4I_CTL_DMAMC_DEDICATED		BIT(5)
 #define SUN4I_CTL_LMTF				BIT(6)
 #define SUN4I_CTL_TF_RST			BIT(8)
 #define SUN4I_CTL_RF_RST			BIT(9)
@@ -51,6 +54,8 @@ 
 #define SUN4I_INT_STA_REG		0x10
 
 #define SUN4I_DMA_CTL_REG		0x14
+#define SUN4I_DMA_CTL_RF_READY			BIT(0)
+#define SUN4I_DMA_CTL_TF_NOT_FULL		BIT(10)
 
 #define SUN4I_WAIT_REG			0x18
 
@@ -84,6 +89,9 @@  struct sun4i_spi {
 	const u8		*tx_buf;
 	u8			*rx_buf;
 	int			len;
+
+	struct dma_chan		*rx_dma_chan;
+	struct dma_chan		*tx_dma_chan;
 };
 
 static inline u32 sun4i_spi_read(struct sun4i_spi *sspi, u32 reg)
@@ -130,6 +138,24 @@  static inline void sun4i_spi_fill_fifo(struct sun4i_spi *sspi, int len)
 	}
 }
 
+static bool sun4i_spi_can_dma(struct spi_master *master,
+			      struct spi_device *spi,
+			      struct spi_transfer *tfr)
+{
+	return tfr->len >= SUN4I_FIFO_DEPTH;
+}
+
+static int sun4i_spi_prepare_message(struct spi_master *master,
+				     struct spi_message *msg)
+{
+	struct sun4i_spi *sspi = spi_master_get_devdata(master);
+
+	master->dma_rx = sspi->rx_dma_chan;
+	master->dma_tx = sspi->tx_dma_chan;
+
+	return 0;
+}
+
 static void sun4i_spi_set_cs(struct spi_device *spi, bool enable)
 {
 	struct sun4i_spi *sspi = spi_master_get_devdata(spi->master);
@@ -169,15 +195,12 @@  static int sun4i_spi_transfer_one(struct spi_master *master,
 				  struct spi_transfer *tfr)
 {
 	struct sun4i_spi *sspi = spi_master_get_devdata(master);
+	struct dma_async_tx_descriptor *desc_tx = NULL, *desc_rx = NULL;
 	unsigned int mclk_rate, div, timeout;
 	unsigned int tx_len = 0;
 	int ret = 0;
 	u32 reg;
 
-	/* We don't support transfer larger than the FIFO */
-	if (tfr->len > SUN4I_FIFO_DEPTH)
-		return -EINVAL;
-
 	reinit_completion(&sspi->done);
 	sspi->tx_buf = tfr->tx_buf;
 	sspi->rx_buf = tfr->rx_buf;
@@ -186,7 +209,6 @@  static int sun4i_spi_transfer_one(struct spi_master *master,
 	/* Clear pending interrupts */
 	sun4i_spi_write(sspi, SUN4I_INT_STA_REG, ~0);
 
-
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
 
 	/* Reset FIFOs */
@@ -269,12 +291,63 @@  static int sun4i_spi_transfer_one(struct spi_master *master,
 	sun4i_spi_write(sspi, SUN4I_BURST_CNT_REG, SUN4I_BURST_CNT(tfr->len));
 	sun4i_spi_write(sspi, SUN4I_XMIT_CNT_REG, SUN4I_XMIT_CNT(tx_len));
 
-	/* Fill the TX FIFO */
-	sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
-
 	/* Enable the interrupts */
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, SUN4I_INT_CTL_TC);
 
+	if (sun4i_spi_can_dma(master, spi, tfr)) {
+		dev_dbg(&sspi->master->dev, "Using DMA mode for transfer\n");
+
+		if (sspi->tx_buf) {
+			desc_tx = dmaengine_prep_slave_sg(sspi->tx_dma_chan,
+					tfr->tx_sg.sgl, tfr->tx_sg.nents,
+					DMA_TO_DEVICE,
+					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+			if (!desc_tx) {
+				dev_err(&sspi->master->dev,
+					"Couldn't prepare dma slave\n");
+				return -EIO;
+			}
+
+			dmaengine_submit(desc_tx);
+		}
+
+		if (sspi->rx_buf) {
+			desc_rx = dmaengine_prep_slave_sg(sspi->rx_dma_chan,
+					tfr->rx_sg.sgl, tfr->rx_sg.nents,
+					DMA_FROM_DEVICE,
+					DMA_PREP_INTERRUPT | DMA_CTRL_ACK);
+			if (!desc_rx) {
+				dev_err(&sspi->master->dev,
+					"Couldn't prepare dma slave\n");
+				return -EIO;
+			}
+
+			dmaengine_submit(desc_rx);
+		}
+
+		/* Enable DMA requests */
+		reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
+		sun4i_spi_write(sspi, SUN4I_CTL_REG,
+				reg | SUN4I_CTL_DMAMC_DEDICATED);
+		sun4i_spi_write(sspi, SUN4I_DMA_CTL_REG,
+				SUN4I_DMA_CTL_TF_NOT_FULL |
+				SUN4I_DMA_CTL_RF_READY);
+
+		dma_async_issue_pending(sspi->rx_dma_chan);
+		dma_async_issue_pending(sspi->tx_dma_chan);
+	} else {
+		dev_dbg(&sspi->master->dev, "Using PIO mode for transfer\n");
+
+		/* Disable DMA requests */
+		reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
+		sun4i_spi_write(sspi, SUN4I_CTL_REG,
+				reg & ~SUN4I_CTL_DMAMC_DEDICATED);
+		sun4i_spi_write(sspi, SUN4I_DMA_CTL_REG, 0);
+
+		/* Fill the TX FIFO */
+		sun4i_spi_fill_fifo(sspi, SUN4I_FIFO_DEPTH);
+	}
+
 	/* Start the transfer */
 	reg = sun4i_spi_read(sspi, SUN4I_CTL_REG);
 	sun4i_spi_write(sspi, SUN4I_CTL_REG, reg | SUN4I_CTL_XCH);
@@ -286,7 +359,12 @@  static int sun4i_spi_transfer_one(struct spi_master *master,
 		goto out;
 	}
 
-	sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+	if (sun4i_spi_can_dma(master, spi, tfr) && desc_rx) {
+		/* The receive transfer should be the last one to finish */
+		dma_wait_for_async_tx(desc_rx);
+	} else {
+		sun4i_spi_drain_fifo(sspi, SUN4I_FIFO_DEPTH);
+	}
 
 out:
 	sun4i_spi_write(sspi, SUN4I_INT_CTL_REG, 0);
@@ -351,6 +429,7 @@  static int sun4i_spi_runtime_suspend(struct device *dev)
 
 static int sun4i_spi_probe(struct platform_device *pdev)
 {
+	struct dma_slave_config dma_sconfig;
 	struct spi_master *master;
 	struct sun4i_spi *sspi;
 	struct resource	*res;
@@ -386,7 +465,10 @@  static int sun4i_spi_probe(struct platform_device *pdev)
 		goto err_free_master;
 	}
 
+	init_completion(&sspi->done);
 	sspi->master = master;
+	master->can_dma = sun4i_spi_can_dma;
+	master->prepare_message = sun4i_spi_prepare_message;
 	master->set_cs = sun4i_spi_set_cs;
 	master->transfer_one = sun4i_spi_transfer_one;
 	master->num_chipselect = 4;
@@ -409,7 +491,45 @@  static int sun4i_spi_probe(struct platform_device *pdev)
 		goto err_free_master;
 	}
 
-	init_completion(&sspi->done);
+	sspi->tx_dma_chan = dma_request_slave_channel_reason(&pdev->dev, "tx");
+	if (IS_ERR(sspi->tx_dma_chan)) {
+		dev_err(&pdev->dev, "Unable to acquire DMA channel TX\n");
+		ret = PTR_ERR(sspi->tx_dma_chan);
+		goto err_free_master;
+	}
+
+	dma_sconfig.direction = DMA_MEM_TO_DEV;
+	dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	dma_sconfig.dst_addr = res->start + SUN4I_TXDATA_REG;
+	dma_sconfig.src_maxburst = 1;
+	dma_sconfig.dst_maxburst = 1;
+
+	ret = dmaengine_slave_config(sspi->tx_dma_chan, &dma_sconfig);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to configure TX DMA slave\n");
+		goto err_tx_dma_release;
+	}
+
+	sspi->rx_dma_chan = dma_request_slave_channel_reason(&pdev->dev, "rx");
+	if (IS_ERR(sspi->rx_dma_chan)) {
+		dev_err(&pdev->dev, "Unable to acquire DMA channel RX\n");
+		ret = PTR_ERR(sspi->rx_dma_chan);
+		goto err_tx_dma_release;
+	}
+
+	dma_sconfig.direction = DMA_DEV_TO_MEM;
+	dma_sconfig.src_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	dma_sconfig.dst_addr_width = DMA_SLAVE_BUSWIDTH_1_BYTE;
+	dma_sconfig.src_addr = res->start + SUN4I_RXDATA_REG;
+	dma_sconfig.src_maxburst = 1;
+	dma_sconfig.dst_maxburst = 1;
+
+	ret = dmaengine_slave_config(sspi->rx_dma_chan, &dma_sconfig);
+	if (ret) {
+		dev_err(&pdev->dev, "Unable to configure RX DMA slave\n");
+		goto err_rx_dma_release;
+	}
 
 	/*
 	 * This wake-up/shutdown pattern is to be able to have the
@@ -418,7 +538,7 @@  static int sun4i_spi_probe(struct platform_device *pdev)
 	ret = sun4i_spi_runtime_resume(&pdev->dev);
 	if (ret) {
 		dev_err(&pdev->dev, "Couldn't resume the device\n");
-		goto err_free_master;
+		goto err_rx_dma_release;
 	}
 
 	pm_runtime_set_active(&pdev->dev);
@@ -436,6 +556,10 @@  static int sun4i_spi_probe(struct platform_device *pdev)
 err_pm_disable:
 	pm_runtime_disable(&pdev->dev);
 	sun4i_spi_runtime_suspend(&pdev->dev);
+err_rx_dma_release:
+	dma_release_channel(sspi->rx_dma_chan);
+err_tx_dma_release:
+	dma_release_channel(sspi->tx_dma_chan);
 err_free_master:
 	spi_master_put(master);
 	return ret;
@@ -443,8 +567,17 @@  err_free_master:
 
 static int sun4i_spi_remove(struct platform_device *pdev)
 {
+	struct spi_master *master = platform_get_drvdata(pdev);
+	struct sun4i_spi *sspi = spi_master_get_devdata(master);
+
+	if (pm_runtime_active(&pdev->dev))
+		sun4i_spi_runtime_suspend(&pdev->dev);
+
 	pm_runtime_disable(&pdev->dev);
 
+	dma_release_channel(sspi->rx_dma_chan);
+	dma_release_channel(sspi->tx_dma_chan);
+
 	return 0;
 }