| Message ID | 1415267509-16653-1-git-send-email-padma.v@samsung.com (mailing list archive) |
|---|---|
| State | Accepted |
| Commit | bf77cba95f8c06bbf76869d3bdfb03e18a33e673 |
| Headers | show |
On Thu, Nov 06, 2014 at 03:21:49PM +0530, Padmavathi Venna wrote: > Exynos7 SPI controller supports only the auto Selection of > CS toggle mode and Exynos7 SoC includes six SPI controllers. > Add support for these changes in Exynos7 SPI controller driver. Could you give a bit more detail on what the "auto selection of CS toggle mode" is - in the diff it looks like it's not an existing mode. I'm a bit worried that it's not going to function well with devices that send more than one transfer per message. > Signed-off-by: Padmavathi Venna <padma.v@samsung.com> It's better if your signoff is using the same e-maill address as
Hi Mark, CCing Kukjin Kim. On 11/6/14, Mark Brown <broonie@kernel.org> wrote: > On Thu, Nov 06, 2014 at 03:21:49PM +0530, Padmavathi Venna wrote: >> Exynos7 SPI controller supports only the auto Selection of >> CS toggle mode and Exynos7 SoC includes six SPI controllers. >> Add support for these changes in Exynos7 SPI controller driver. > > Could you give a bit more detail on what the "auto selection of CS > toggle mode" is - in the diff it looks like it's not an existing mode. > I'm a bit worried that it's not going to function well with devices that > send more than one transfer per message. There is a bit AUTO_N_MANUAL(as per manual) in the spi CS_CFG register(as per manual, in the driver it is S3C64XX_SPI_SLAVE_SEL) to control the CS toggle mode either manually or automatically. If CS has to be controlled manually the AUTO_N_MANUAL should be set to 0 which the driver is doing in the s3c64xx_spi_transfer_one function by writing 0 in the S3C64XX_SPI_SLAVE_SEL. When it is handled manually NSSOUT as per the manual(in the driver it is S3C64XX_SPI_SLAVE_SIG_INACT) controls the level of CS which when set deactivates the signal and reset activates. CS can also be controlled automatically by setting AUTO_N_MANUAL to 1 in CS_CFG. When it is auto CS automatically toggles between packet to packet. NCS_TIME_COUNT in CS_CFG controls the inactive period. The driver by default uses manual mode. But on exynos7 the manual mode is removed. I tested the driver with wm5110 codec. > >> Signed-off-by: Padmavathi Venna <padma.v@samsung.com> > > It's better if your signoff is using the same e-maill address as ok. I will take care of this. > Thanks Padma -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Fri, Nov 07, 2014 at 02:01:57PM +0530, Padma Venkat wrote: > CS can also be controlled automatically by setting AUTO_N_MANUAL to 1 > in CS_CFG. When it is auto CS automatically toggles between packet to > packet. NCS_TIME_COUNT in CS_CFG controls the inactive period. The > driver by default uses manual mode. But on exynos7 the manual mode is > removed. OK, but what's a packet here? > I tested the driver with wm5110 codec. Did you try firmware downloads or something else that generates multiple transfers in a message? Normal register writes will use a single transfer so I'd expect them to just work.
Hi Mark, On 11/7/14, Mark Brown <broonie@kernel.org> wrote: > On Fri, Nov 07, 2014 at 02:01:57PM +0530, Padma Venkat wrote: > >> CS can also be controlled automatically by setting AUTO_N_MANUAL to 1 >> in CS_CFG. When it is auto CS automatically toggles between packet to >> packet. NCS_TIME_COUNT in CS_CFG controls the inactive period. The >> driver by default uses manual mode. But on exynos7 the manual mode is >> removed. > > OK, but what's a packet here? Packet is either 1 byte or 4 bytes size depends on width of the SPI channel. > >> I tested the driver with wm5110 codec. > > Did you try firmware downloads or something else that generates multiple > transfers in a message? Normal register writes will use a single > transfer so I'd expect them to just work. > OK. I don't have provision to test on this board. I will try to test on older boards by disabling manual mode. Thanks padma -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Mark, On 11/10/14, Padma Venkat <padma.kvr@gmail.com> wrote: > Hi Mark, > > On 11/7/14, Mark Brown <broonie@kernel.org> wrote: >> On Fri, Nov 07, 2014 at 02:01:57PM +0530, Padma Venkat wrote: >> >>> CS can also be controlled automatically by setting AUTO_N_MANUAL to 1 >>> in CS_CFG. When it is auto CS automatically toggles between packet to >>> packet. NCS_TIME_COUNT in CS_CFG controls the inactive period. The >>> driver by default uses manual mode. But on exynos7 the manual mode is >>> removed. >> >> OK, but what's a packet here? > > Packet is either 1 byte or 4 bytes size depends on width of the SPI > channel. > >> >>> I tested the driver with wm5110 codec. >> >> Did you try firmware downloads or something else that generates multiple >> transfers in a message? Normal register writes will use a single >> transfer so I'd expect them to just work. >> > > OK. I don't have provision to test on this board. I will try to test > on older boards by disabling manual mode. > I tested on exynos5420 peach-pit by enabling auto mode. I used dd command to read 1MB data from spi flash and I compared the result with manual mode. Both are same. > Thanks > padma > -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Mark, >>>> CS can also be controlled automatically by setting AUTO_N_MANUAL to 1 >>>> in CS_CFG. When it is auto CS automatically toggles between packet to >>>> packet. NCS_TIME_COUNT in CS_CFG controls the inactive period. The >>>> driver by default uses manual mode. But on exynos7 the manual mode is >>>> removed. >>> >>> OK, but what's a packet here? >> >> Packet is either 1 byte or 4 bytes size depends on width of the SPI >> channel. >> >>> >>>> I tested the driver with wm5110 codec. >>> >>> Did you try firmware downloads or something else that generates multiple >>> transfers in a message? Normal register writes will use a single >>> transfer so I'd expect them to just work. >>> >> >> OK. I don't have provision to test on this board. I will try to test >> on older boards by disabling manual mode. >> > > I tested on exynos5420 peach-pit by enabling auto mode. I used dd > command to read 1MB data from spi flash and I compared the result with > manual mode. Both are same. I also tested this patch with Javier Martinez Canillas patches for enabling spidev nodes from http://www.spinics.net/lists/linux-samsung-soc/msg39057.html. I read 4MB flashdata from spi by enabling auto mode and compared the result. They look same. > >> Thanks >> padma >> > -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
Hi Mark, >>> OK. I don't have provision to test on this board. I will try to test >>> on older boards by disabling manual mode. >>> >> >> I tested on exynos5420 peach-pit by enabling auto mode. I used dd >> command to read 1MB data from spi flash and I compared the result with >> manual mode. Both are same. > > I also tested this patch with Javier Martinez Canillas patches for > enabling spidev nodes from > http://www.spinics.net/lists/linux-samsung-soc/msg39057.html. > > I read 4MB flashdata from spi by enabling auto mode and compared the > result. They look same. Do want some extra tests need to be done for this patch or is it okey? > >> >>> Thanks >>> padma >>> >> > -- To unsubscribe from this list: send the line "unsubscribe linux-spi" in the body of a message to majordomo@vger.kernel.org More majordomo info at http://vger.kernel.org/majordomo-info.html
On Thu, Nov 06, 2014 at 03:21:49PM +0530, Padmavathi Venna wrote: > Exynos7 SPI controller supports only the auto Selection of > CS toggle mode and Exynos7 SoC includes six SPI controllers. > Add support for these changes in Exynos7 SPI controller driver. Applied, thanks. It does seem like these controllers are getting more restricted in functionality which seems a bit of a shame.
diff --git a/Documentation/devicetree/bindings/spi/spi-samsung.txt b/Documentation/devicetree/bindings/spi/spi-samsung.txt index 1e8a857..6dbdeb3 100644 --- a/Documentation/devicetree/bindings/spi/spi-samsung.txt +++ b/Documentation/devicetree/bindings/spi/spi-samsung.txt @@ -9,7 +9,7 @@ Required SoC Specific Properties: - samsung,s3c2443-spi: for s3c2443, s3c2416 and s3c2450 platforms - samsung,s3c6410-spi: for s3c6410 platforms - samsung,s5pv210-spi: for s5pv210 and s5pc110 platforms - - samsung,exynos4210-spi: for exynos4 and exynos5 platforms + - samsung,exynos7-spi: for exynos7 platforms - reg: physical base address of the controller and length of memory mapped region. diff --git a/drivers/spi/Kconfig b/drivers/spi/Kconfig index 84e7c9e..de2d33d 100644 --- a/drivers/spi/Kconfig +++ b/drivers/spi/Kconfig @@ -444,7 +444,7 @@ config SPI_S3C24XX_FIQ config SPI_S3C64XX tristate "Samsung S3C64XX series type SPI" - depends on PLAT_SAMSUNG + depends on (PLAT_SAMSUNG || ARCH_EXYNOS) select S3C64XX_PL080 if ARCH_S3C64XX help SPI driver for Samsung S3C64XX and newer SoCs. diff --git a/drivers/spi/spi-s3c64xx.c b/drivers/spi/spi-s3c64xx.c index 480133e..59e07cf 100644 --- a/drivers/spi/spi-s3c64xx.c +++ b/drivers/spi/spi-s3c64xx.c @@ -33,8 +33,9 @@ #include <linux/platform_data/spi-s3c64xx.h> -#define MAX_SPI_PORTS 3 +#define MAX_SPI_PORTS 6 #define S3C64XX_SPI_QUIRK_POLL (1 << 0) +#define S3C64XX_SPI_QUIRK_CS_AUTO (1 << 1) /* Registers and bit-fields */ @@ -78,6 +79,7 @@ #define S3C64XX_SPI_SLAVE_AUTO (1<<1) #define S3C64XX_SPI_SLAVE_SIG_INACT (1<<0) +#define S3C64XX_SPI_SLAVE_NSC_CNT_2 (2<<4) #define S3C64XX_SPI_INT_TRAILING_EN (1<<6) #define S3C64XX_SPI_INT_RX_OVERRUN_EN (1<<5) @@ -717,7 +719,12 @@ static int s3c64xx_spi_transfer_one(struct spi_master *master, enable_datapath(sdd, spi, xfer, use_dma); /* Start the signals */ - writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL); + if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO)) + writel(0, sdd->regs + S3C64XX_SPI_SLAVE_SEL); + else + writel(readl(sdd->regs + S3C64XX_SPI_SLAVE_SEL) + | S3C64XX_SPI_SLAVE_AUTO | S3C64XX_SPI_SLAVE_NSC_CNT_2, + sdd->regs + S3C64XX_SPI_SLAVE_SEL); spin_unlock_irqrestore(&sdd->lock, flags); @@ -866,13 +873,15 @@ static int s3c64xx_spi_setup(struct spi_device *spi) } pm_runtime_put(&sdd->pdev->dev); - writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL); + if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO)) + writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL); return 0; setup_exit: pm_runtime_put(&sdd->pdev->dev); /* setup() returns with device de-selected */ - writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL); + if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO)) + writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL); if (gpio_is_valid(spi->cs_gpio)) gpio_free(spi->cs_gpio); @@ -946,7 +955,8 @@ static void s3c64xx_spi_hwinit(struct s3c64xx_spi_driver_data *sdd, int channel) sdd->cur_speed = 0; - writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL); + if (!(sdd->port_conf->quirks & S3C64XX_SPI_QUIRK_CS_AUTO)) + writel(S3C64XX_SPI_SLAVE_SIG_INACT, sdd->regs + S3C64XX_SPI_SLAVE_SEL); /* Disable Interrupts - we use Polling if not DMA mode */ writel(0, regs + S3C64XX_SPI_INT_EN); @@ -1341,6 +1351,15 @@ static struct s3c64xx_spi_port_config exynos5440_spi_port_config = { .quirks = S3C64XX_SPI_QUIRK_POLL, }; +static struct s3c64xx_spi_port_config exynos7_spi_port_config = { + .fifo_lvl_mask = { 0x1ff, 0x7F, 0x7F, 0x7F, 0x7F, 0x1ff}, + .rx_lvl_offset = 15, + .tx_st_done = 25, + .high_speed = true, + .clk_from_cmu = true, + .quirks = S3C64XX_SPI_QUIRK_CS_AUTO, +}; + static struct platform_device_id s3c64xx_spi_driver_ids[] = { { .name = "s3c2443-spi", @@ -1374,6 +1393,9 @@ static const struct of_device_id s3c64xx_spi_dt_match[] = { { .compatible = "samsung,exynos5440-spi", .data = (void *)&exynos5440_spi_port_config, }, + { .compatible = "samsung,exynos7-spi", + .data = (void *)&exynos7_spi_port_config, + }, { }, }; MODULE_DEVICE_TABLE(of, s3c64xx_spi_dt_match);
Exynos7 SPI controller supports only the auto Selection of CS toggle mode and Exynos7 SoC includes six SPI controllers. Add support for these changes in Exynos7 SPI controller driver. Signed-off-by: Padmavathi Venna <padma.v@samsung.com> --- .../devicetree/bindings/spi/spi-samsung.txt | 2 +- drivers/spi/Kconfig | 2 +- drivers/spi/spi-s3c64xx.c | 32 ++++++++++++++++--- 3 files changed, 29 insertions(+), 7 deletions(-)