new file mode 100644
@@ -0,0 +1,41 @@
+/*
+ * SPI driver definitions for the CPLD chip on the Mikrotik RB4xx boards
+ *
+ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * This file was based on the patches for Linux 2.6.27.39 published by
+ * MikroTik for their RouterBoard 4xx series devices.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#define CPLD_GPIO_nLED1 0
+#define CPLD_GPIO_nLED2 1
+#define CPLD_GPIO_nLED3 2
+#define CPLD_GPIO_nLED4 3
+#define CPLD_GPIO_FAN 4
+#define CPLD_GPIO_ALE 5
+#define CPLD_GPIO_CLE 6
+#define CPLD_GPIO_nCE 7
+#define CPLD_GPIO_nLED5 8
+
+#define CPLD_NUM_GPIOS 9
+
+#define CPLD_CFG_nLED1 BIT(CPLD_GPIO_nLED1)
+#define CPLD_CFG_nLED2 BIT(CPLD_GPIO_nLED2)
+#define CPLD_CFG_nLED3 BIT(CPLD_GPIO_nLED3)
+#define CPLD_CFG_nLED4 BIT(CPLD_GPIO_nLED4)
+#define CPLD_CFG_FAN BIT(CPLD_GPIO_FAN)
+#define CPLD_CFG_ALE BIT(CPLD_GPIO_ALE)
+#define CPLD_CFG_CLE BIT(CPLD_GPIO_CLE)
+#define CPLD_CFG_nCE BIT(CPLD_GPIO_nCE)
+#define CPLD_CFG_nLED5 BIT(CPLD_GPIO_nLED5)
+
+struct rb4xx_cpld_platform_data {
+ unsigned gpio_base;
+};
+
+extern int rb4xx_cpld_read(unsigned char *rx_buf, unsigned cnt);
+extern int rb4xx_cpld_write(const unsigned char *buf, unsigned count);
@@ -435,6 +435,14 @@ config SPI_RB4XX
help
SPI controller driver for the Mikrotik RB4xx series boards.
+config SPI_RB4XX_CPLD
+ tristate "MikroTik RB4XX CPLD driver"
+ depends on ATH79_MACH_RB4XX
+ help
+ SPI driver for the Xilinx CPLD chip present on the MikroTik
+ RB4xx boards. It controls CPU access to the NAND flash and
+ user LEDs.
+
config SPI_RSPI
tristate "Renesas RSPI/QSPI controller"
depends on SUPERH || ARCH_SHMOBILE || COMPILE_TEST
@@ -67,6 +67,7 @@ obj-$(CONFIG_SPI_PXA2XX_PCI) += spi-pxa2xx-pci.o
obj-$(CONFIG_SPI_QUP) += spi-qup.o
obj-$(CONFIG_SPI_ROCKCHIP) += spi-rockchip.o
obj-$(CONFIG_SPI_RB4XX) += spi-rb4xx.o
+obj-$(CONFIG_SPI_RB4XX_CPLD) += spi-rb4xx-cpld.o
obj-$(CONFIG_SPI_RSPI) += spi-rspi.o
obj-$(CONFIG_SPI_S3C24XX) += spi-s3c24xx-hw.o
spi-s3c24xx-hw-y := spi-s3c24xx.o
new file mode 100644
@@ -0,0 +1,326 @@
+/*
+ * SPI driver for the CPLD chip on the Mikrotik RB4xx boards
+ *
+ * Copyright (C) 2010 Gabor Juhos <juhosg@openwrt.org>
+ *
+ * This file was based on the patches for Linux 2.6.27.39 published by
+ * MikroTik for their RouterBoard 4xx series devices.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published
+ * by the Free Software Foundation.
+ */
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/device.h>
+#include <linux/bitops.h>
+#include <linux/spi/spi.h>
+#include <linux/gpio.h>
+#include <linux/slab.h>
+
+#include <asm/mach-ath79/rb4xx_cpld.h>
+
+#define DRV_NAME "spi-rb4xx-cpld"
+#define DRV_DESC "RB4xx CPLD driver"
+#define DRV_VERSION "0.1.0"
+
+#define CPLD_CMD_WRITE_NAND 0x08 /* send cmd, n x send data, send idle */
+#define CPLD_CMD_WRITE_CFG 0x09 /* send cmd, n x send cfg */
+#define CPLD_CMD_READ_NAND 0x0a /* send cmd, send idle, n x read data */
+#define CPLD_CMD_READ_FAST 0x0b /* send cmd, 4 x idle, n x read data */
+#define CPLD_CMD_LED5_ON 0x0c /* send cmd */
+#define CPLD_CMD_LED5_OFF 0x0d /* send cmd */
+
+struct rb4xx_cpld {
+ struct spi_device *spi;
+ struct mutex lock;
+ struct gpio_chip chip;
+ unsigned int config;
+};
+
+static struct rb4xx_cpld *rb4xx_cpld;
+
+static inline struct rb4xx_cpld *gpio_to_cpld(struct gpio_chip *chip)
+{
+ return container_of(chip, struct rb4xx_cpld, chip);
+}
+
+static int rb4xx_cpld_write_cmd(struct rb4xx_cpld *cpld, unsigned char cmd)
+{
+ struct spi_transfer t[1];
+ struct spi_message m;
+ unsigned char tx_buf[1];
+ int err;
+
+ spi_message_init(&m);
+ memset(&t, 0, sizeof(t));
+
+ t[0].tx_buf = tx_buf;
+ t[0].len = sizeof(tx_buf);
+ spi_message_add_tail(&t[0], &m);
+
+ tx_buf[0] = cmd;
+
+ err = spi_sync(cpld->spi, &m);
+ return err;
+}
+
+static int rb4xx_cpld_write_cfg(struct rb4xx_cpld *cpld, unsigned char config)
+{
+ struct spi_transfer t[1];
+ struct spi_message m;
+ unsigned char cmd[2];
+ int err;
+
+ spi_message_init(&m);
+ memset(&t, 0, sizeof(t));
+
+ t[0].tx_buf = cmd;
+ t[0].len = sizeof(cmd);
+ spi_message_add_tail(&t[0], &m);
+
+ cmd[0] = CPLD_CMD_WRITE_CFG;
+ cmd[1] = config;
+
+ err = spi_sync(cpld->spi, &m);
+ return err;
+}
+
+static int __rb4xx_cpld_change_cfg(struct rb4xx_cpld *cpld, unsigned mask,
+ unsigned value)
+{
+ unsigned int config;
+ int err;
+
+ config = cpld->config & ~mask;
+ config |= value;
+
+ if ((cpld->config ^ config) & 0xff) {
+ err = rb4xx_cpld_write_cfg(cpld, config);
+ if (err)
+ return err;
+ }
+
+ if ((cpld->config ^ config) & CPLD_CFG_nLED5) {
+ err = rb4xx_cpld_write_cmd(cpld, (value) ? CPLD_CMD_LED5_ON :
+ CPLD_CMD_LED5_OFF);
+ if (err)
+ return err;
+ }
+
+ cpld->config = config;
+ return 0;
+}
+
+int rb4xx_cpld_read(unsigned char *rx_buf, unsigned count)
+{
+ static const unsigned char cmd[2] = { CPLD_CMD_READ_NAND, 0 };
+ struct spi_transfer t[2] = {
+ {
+ .tx_buf = &cmd,
+ .len = 2,
+ }, {
+ .tx_buf = NULL,
+ .rx_buf = rx_buf,
+ .len = count,
+ },
+ };
+ struct spi_message m;
+
+ if (rb4xx_cpld == NULL)
+ return -ENODEV;
+
+ spi_message_init(&m);
+ spi_message_add_tail(&t[0], &m);
+ spi_message_add_tail(&t[1], &m);
+ return spi_sync(rb4xx_cpld->spi, &m);
+}
+EXPORT_SYMBOL_GPL(rb4xx_cpld_read);
+
+int rb4xx_cpld_write(const unsigned char *buf, unsigned count)
+{
+ static const unsigned char cmd = CPLD_CMD_WRITE_NAND;
+ struct spi_transfer t[3] = {
+ {
+ .tx_buf = &cmd,
+ .len = 1,
+ }, {
+ .tx_buf = buf,
+ .len = count,
+ .fast_write = 1,
+ }, {
+ .len = 1,
+ .fast_write = 1,
+ },
+ };
+ struct spi_message m;
+
+ if (rb4xx_cpld == NULL)
+ return -ENODEV;
+
+ spi_message_init(&m);
+ spi_message_add_tail(&t[0], &m);
+ spi_message_add_tail(&t[1], &m);
+ spi_message_add_tail(&t[2], &m);
+ return spi_sync(rb4xx_cpld->spi, &m);
+}
+EXPORT_SYMBOL_GPL(rb4xx_cpld_write);
+
+static int rb4xx_cpld_gpio_get(struct gpio_chip *chip, unsigned offset)
+{
+ struct rb4xx_cpld *cpld = gpio_to_cpld(chip);
+ int ret;
+
+ mutex_lock(&cpld->lock);
+ ret = (cpld->config >> offset) & 1;
+ mutex_unlock(&cpld->lock);
+
+ return ret;
+}
+
+static void rb4xx_cpld_gpio_set(struct gpio_chip *chip, unsigned offset,
+ int value)
+{
+ struct rb4xx_cpld *cpld = gpio_to_cpld(chip);
+
+ mutex_lock(&cpld->lock);
+ __rb4xx_cpld_change_cfg(cpld, (1 << offset), !!value << offset);
+ mutex_unlock(&cpld->lock);
+}
+
+static int rb4xx_cpld_gpio_direction_input(struct gpio_chip *chip,
+ unsigned offset)
+{
+ return -EOPNOTSUPP;
+}
+
+static int rb4xx_cpld_gpio_direction_output(struct gpio_chip *chip,
+ unsigned offset,
+ int value)
+{
+ struct rb4xx_cpld *cpld = gpio_to_cpld(chip);
+ int ret;
+
+ mutex_lock(&cpld->lock);
+ ret = __rb4xx_cpld_change_cfg(cpld, (1 << offset), !!value << offset);
+ mutex_unlock(&cpld->lock);
+
+ return ret;
+}
+
+static int rb4xx_cpld_gpio_init(struct rb4xx_cpld *cpld, unsigned int base)
+{
+ int err;
+
+ /* init config */
+ cpld->config = CPLD_CFG_nLED1 | CPLD_CFG_nLED2 | CPLD_CFG_nLED3 |
+ CPLD_CFG_nLED4 | CPLD_CFG_nLED5;
+ rb4xx_cpld_write_cfg(cpld, cpld->config);
+
+ /* setup GPIO chip */
+ cpld->chip.label = DRV_NAME;
+
+ cpld->chip.get = rb4xx_cpld_gpio_get;
+ cpld->chip.set = rb4xx_cpld_gpio_set;
+ cpld->chip.direction_input = rb4xx_cpld_gpio_direction_input;
+ cpld->chip.direction_output = rb4xx_cpld_gpio_direction_output;
+
+ cpld->chip.base = base;
+ cpld->chip.ngpio = CPLD_NUM_GPIOS;
+ cpld->chip.can_sleep = 1;
+ cpld->chip.dev = &cpld->spi->dev;
+ cpld->chip.owner = THIS_MODULE;
+
+ err = gpiochip_add(&cpld->chip);
+ if (err)
+ dev_err(&cpld->spi->dev, "adding GPIO chip failed, err=%d\n",
+ err);
+
+ return err;
+}
+
+static int rb4xx_cpld_probe(struct spi_device *spi)
+{
+ struct rb4xx_cpld *cpld;
+ struct rb4xx_cpld_platform_data *pdata;
+ int err;
+
+ pdata = spi->dev.platform_data;
+ if (!pdata) {
+ dev_dbg(&spi->dev, "no platform data\n");
+ return -EINVAL;
+ }
+
+ cpld = kzalloc(sizeof(*cpld), GFP_KERNEL);
+ if (!cpld)
+ return -ENOMEM;
+
+ mutex_init(&cpld->lock);
+ cpld->spi = spi_dev_get(spi);
+ dev_set_drvdata(&spi->dev, cpld);
+
+ spi->mode = SPI_MODE_0;
+ spi->bits_per_word = 8;
+ err = spi_setup(spi);
+ if (err) {
+ dev_err(&spi->dev, "spi_setup failed, err=%d\n", err);
+ goto err_drvdata;
+ }
+
+ err = rb4xx_cpld_gpio_init(cpld, pdata->gpio_base);
+ if (err)
+ goto err_drvdata;
+
+ rb4xx_cpld = cpld;
+
+ return 0;
+
+err_drvdata:
+ dev_set_drvdata(&spi->dev, NULL);
+ kfree(cpld);
+
+ return err;
+}
+
+static int rb4xx_cpld_remove(struct spi_device *spi)
+{
+ struct rb4xx_cpld *cpld;
+
+ rb4xx_cpld = NULL;
+ cpld = dev_get_drvdata(&spi->dev);
+ dev_set_drvdata(&spi->dev, NULL);
+ kfree(cpld);
+
+ return 0;
+}
+
+static struct spi_driver rb4xx_cpld_driver = {
+ .driver = {
+ .name = DRV_NAME,
+ .bus = &spi_bus_type,
+ .owner = THIS_MODULE,
+ },
+ .probe = rb4xx_cpld_probe,
+ .remove = rb4xx_cpld_remove,
+};
+
+static int __init rb4xx_cpld_init(void)
+{
+ return spi_register_driver(&rb4xx_cpld_driver);
+}
+module_init(rb4xx_cpld_init);
+
+static void __exit rb4xx_cpld_exit(void)
+{
+ spi_unregister_driver(&rb4xx_cpld_driver);
+}
+module_exit(rb4xx_cpld_exit);
+
+MODULE_DESCRIPTION(DRV_DESC);
+MODULE_VERSION(DRV_VERSION);
+MODULE_AUTHOR("Gabor Juhos <juhosg@openwrt.org>");
+MODULE_LICENSE("GPL v2");
The CPLD is connected to the NAND flash chip and five LEDs. Access to those devices goes via this driver. Signed-off-by: Bert Vermeulen <bert@biot.com> --- arch/mips/include/asm/mach-ath79/rb4xx_cpld.h | 41 ++++ drivers/spi/Kconfig | 8 + drivers/spi/Makefile | 1 + drivers/spi/spi-rb4xx-cpld.c | 326 ++++++++++++++++++++++++++ 4 files changed, 376 insertions(+) create mode 100644 arch/mips/include/asm/mach-ath79/rb4xx_cpld.h create mode 100644 drivers/spi/spi-rb4xx-cpld.c