old mode 100755
new mode 100644
@@ -20,6 +20,7 @@
#include <linux/ioport.h>
#include <linux/module.h>
#include <linux/of.h>
+#include <linux/of_gpio.h>
#include <linux/platform_device.h>
#include <linux/platform_data/spi-mt65xx.h>
#include <linux/pm_runtime.h>
@@ -84,7 +85,8 @@ struct mtk_spi_compatible {
struct mtk_spi {
void __iomem *base;
u32 state;
- u32 pad_sel;
+ int pad_num;
+ u32 *pad_sel;
struct clk *parent_clk, *sel_clk, *spi_clk;
struct spi_transfer *cur_transfer;
u32 xfer_len;
@@ -188,7 +190,8 @@ static int mtk_spi_prepare_message(struct spi_master *master,
/* pad select */
if (mdata->dev_comp->need_pad_sel)
- writel(mdata->pad_sel, mdata->base + SPI_PAD_SEL_REG);
+ writel(mdata->pad_sel[spi->chip_select],
+ mdata->base + SPI_PAD_SEL_REG);
return 0;
}
@@ -407,6 +410,9 @@ static int mtk_spi_setup(struct spi_device *spi)
if (!spi->controller_data)
spi->controller_data = (void *)&mtk_default_chip_info;
+ if (mdata->dev_comp->need_pad_sel)
+ gpio_direction_output(spi->cs_gpio, !(spi->mode & SPI_CS_HIGH));
+
return 0;
}
@@ -481,7 +487,7 @@ static int mtk_spi_probe(struct platform_device *pdev)
struct mtk_spi *mdata;
const struct of_device_id *of_id;
struct resource *res;
- int irq, ret;
+ int i, irq, ret;
master = spi_alloc_master(&pdev->dev, sizeof(*mdata));
if (!master) {
@@ -512,21 +518,34 @@ static int mtk_spi_probe(struct platform_device *pdev)
master->flags = SPI_MASTER_MUST_TX;
if (mdata->dev_comp->need_pad_sel) {
- ret = of_property_read_u32(pdev->dev.of_node,
- "mediatek,pad-select",
- &mdata->pad_sel);
- if (ret) {
- dev_err(&pdev->dev, "failed to read pad select: %d\n",
- ret);
+ mdata->pad_num = of_property_count_u32_elems(
+ pdev->dev.of_node,
+ "mediatek,pad-select");
+ if (mdata->pad_num < 0) {
+ dev_err(&pdev->dev,
+ "No 'mediatek,pad-select' property\n");
+ ret = -EINVAL;
goto err_put_master;
}
- if (mdata->pad_sel > MT8173_SPI_MAX_PAD_SEL) {
- dev_err(&pdev->dev, "wrong pad-select: %u\n",
- mdata->pad_sel);
- ret = -EINVAL;
+ mdata->pad_sel = devm_kmalloc_array(&pdev->dev, mdata->pad_num,
+ sizeof(u32), GFP_KERNEL);
+ if (!mdata->pad_sel) {
+ ret = -ENOMEM;
goto err_put_master;
}
+
+ for (i = 0; i < mdata->pad_num; i++) {
+ of_property_read_u32_index(pdev->dev.of_node,
+ "mediatek,pad-select",
+ i, &mdata->pad_sel[i]);
+ if (mdata->pad_sel[i] > MT8173_SPI_MAX_PAD_SEL) {
+ dev_err(&pdev->dev, "wrong pad-sel[%d]: %u\n",
+ i, mdata->pad_sel[i]);
+ ret = -EINVAL;
+ goto err_put_master;
+ }
+ }
}
platform_set_drvdata(pdev, master);
@@ -604,6 +623,26 @@ static int mtk_spi_probe(struct platform_device *pdev)
goto err_put_master;
}
+ if (mdata->dev_comp->need_pad_sel) {
+ if (mdata->pad_num != master->num_chipselect) {
+ dev_err(&pdev->dev,
+ "pad_num does not match num_chipselect(%d != %d)\n",
+ mdata->pad_num, master->num_chipselect);
+ ret = -EINVAL;
+ goto err_put_master;
+ }
+
+ for (i = 0; i < master->num_chipselect; i++) {
+ ret = devm_gpio_request(&pdev->dev, master->cs_gpios[i],
+ dev_name(&pdev->dev));
+ if (ret) {
+ dev_err(&pdev->dev,
+ "can't get CS GPIO %i\n", i);
+ goto err_put_master;
+ }
+ }
+ }
+
return 0;
err_disable_clk:
mt8173 IC spi HW has 4 gpio group, it's possible to support max <= 4 slave devices, even mtk spi HW is not congruent to spi core. 1. When a device do a spi_message transfer, spi HW should know which pad-group this device is on, and then writes pad-select register. 2. Mtk pad-select register just selects which MISO pin HW will receive data. For example, pad-select=1(select spi1 pins), HW just receives data from spi1 MISO, but it still send waveform to all 4 group cs/clk/mosi. If cs pin in other groups is still spi mode, after spi1 is selected(by active cs pin), devices on other group will also be selected. Signed-off-by: Leilk Liu <leilk.liu@mediatek.com> --- drivers/spi/spi-mt65xx.c | 65 ++++++++++++++++++++++++++++++++++++++---------- 1 file changed, 52 insertions(+), 13 deletions(-) mode change 100755 => 100644 drivers/spi/spi-mt65xx.c