@@ -153,6 +153,7 @@ enum mode_type {GQSPI_MODE_IO, GQSPI_MODE_DMA};
* @dma_rx_bytes: Remaining bytes to receive by DMA mode
* @dma_addr: DMA address after mapping the kernel buffer
* @genfifoentry: Used for storing the genfifoentry instruction.
+ * @isinstr: To determine whether the transfer is instruction
* @mode: Defines the mode in which QSPI is operating
*/
struct zynqmp_qspi {
@@ -170,6 +171,7 @@ struct zynqmp_qspi {
u32 dma_rx_bytes;
dma_addr_t dma_addr;
u32 genfifoentry;
+ bool isinstr;
enum mode_type mode;
};
@@ -404,11 +406,24 @@ static void zynqmp_qspi_chipselect(struct spi_device *qspi, bool is_high)
u32 genfifoentry = 0x0, statusreg;
genfifoentry |= GQSPI_GENFIFO_MODE_SPI;
+
+
+ if (qspi->master->flags & SPI_MASTER_BOTH_CS) {
+ zynqmp_gqspi_selectslave(xqspi,
+ GQSPI_SELECT_FLASH_CS_BOTH,
+ GQSPI_SELECT_FLASH_BUS_BOTH);
+ } else {
+ zynqmp_gqspi_selectslave(xqspi,
+ GQSPI_SELECT_FLASH_CS_LOWER,
+ GQSPI_SELECT_FLASH_BUS_LOWER);
+ }
+
genfifoentry |= xqspi->genfifobus;
if (!is_high) {
genfifoentry |= xqspi->genfifocs;
genfifoentry |= GQSPI_GENFIFO_CS_SETUP;
+ xqspi->isinstr = true;
} else {
genfifoentry |= GQSPI_GENFIFO_CS_HOLD;
}
@@ -665,6 +680,7 @@ static irqreturn_t zynqmp_qspi_irq(int irq, void *dev_id)
if ((xqspi->bytes_to_receive == 0) && (xqspi->bytes_to_transfer == 0)
&& ((status & GQSPI_IRQ_MASK) == GQSPI_IRQ_MASK)) {
zynqmp_gqspi_write(xqspi, GQSPI_IDR_OFST, GQSPI_ISR_IDR_MASK);
+ xqspi->isinstr = false;
spi_finalize_current_transfer(master);
ret = IRQ_HANDLED;
}
@@ -828,6 +844,9 @@ static int zynqmp_qspi_start_transfer(struct spi_master *master,
genfifoentry |= xqspi->genfifocs;
genfifoentry |= xqspi->genfifobus;
+ if ((!xqspi->isinstr) && (master->flags & SPI_MASTER_DATA_STRIPE))
+ genfifoentry |= GQSPI_GENFIFO_STRIPE;
+
zynqmp_qspi_txrxsetup(xqspi, transfer, &genfifoentry);
if (xqspi->mode == GQSPI_MODE_DMA)
@@ -980,6 +999,7 @@ static int zynqmp_qspi_probe(struct platform_device *pdev)
struct zynqmp_qspi *xqspi;
struct resource *res;
struct device *dev = &pdev->dev;
+ u32 num_cs;
master = spi_alloc_master(&pdev->dev, sizeof(*xqspi));
if (!master)
@@ -1040,7 +1060,11 @@ static int zynqmp_qspi_probe(struct platform_device *pdev)
goto clk_dis_all;
}
- master->num_chipselect = GQSPI_DEFAULT_NUM_CS;
+ ret = of_property_read_u32(pdev->dev.of_node, "num-cs", &num_cs);
+ if (ret < 0)
+ master->num_chipselect = GQSPI_DEFAULT_NUM_CS;
+ else
+ master->num_chipselect = num_cs;
master->setup = zynqmp_qspi_setup;
master->set_cs = zynqmp_qspi_chipselect;
This patch adds support of dual parallel mode configuration for Zynq Ultrascale+ MPSoC GQSPI controller driver. Signed-off-by: Naga Sureshkumar Relli <nagasure@xilinx.com> --- Changes for v4: - No changes Changes for v3: - No change Changes for v2: - No change --- drivers/spi/spi-zynqmp-gqspi.c | 26 +++++++++++++++++++++++++- 1 file changed, 25 insertions(+), 1 deletion(-)