@@ -1632,4 +1632,10 @@ config SERIAL_ALTERA_UART_CONSOLE
help
Enable a Altera UART port to be the system console.
+config SERIAL_IFX6X60
+ tristate "SPI protocol driver for Infineon 6x60 modem (EXPERIMENTAL)"
+ depends on GPIOLIB && EXPERIMENTAL
+ help
+ Support for the IFX6x60 modem devices on Intel MID platforms.
+
endmenu
@@ -89,3 +89,4 @@ obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
obj-$(CONFIG_SERIAL_MRST_MAX3110) += mrst_max3110.o
obj-$(CONFIG_SERIAL_MFD_HSU) += mfd.o
obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
+obj-$(CONFIG_SERIAL_IFX6X60) += ifx6x60.o
new file mode 100644
@@ -0,0 +1,1402 @@
+/****************************************************************************
+ *
+ * Driver for the IFX 6x60 spi modem.
+ *
+ * Copyright (C) 2008 Option International
+ * Copyright (C) 2008 Filip Aben <f.aben@option.com>
+ * Denis Joseph Barrow <d.barow@option.com>
+ * Jan Dumon <j.dumon@option.com>
+ *
+ * Copyright (C) 2009, 2010 Intel Corp
+ * Russ Gorby <richardx.r.gorby@intel.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
+ * USA
+ *
+ * Driver modified by Intel from Option gtm501l_spi.c
+ *
+ * Notes
+ * o The driver currently assumes a single device only. If you need to
+ * change this then look for saved_ifx_dev and add a device lookup
+ * o The driver is intended to be big-endian safe but has never been
+ * tested that way (no suitable hardware). There are a couple of FIXME
+ * notes by areas that may need addressing
+ * o Some of the GPIO naming/setup assumptions may need revisiting if
+ * you need to use this driver for another platform.
+ *
+ *****************************************************************************/
+#include <linux/module.h>
+#include <linux/termios.h>
+#include <linux/tty.h>
+#include <linux/device.h>
+#include <linux/spi/spi.h>
+#include <linux/tty.h>
+#include <linux/kfifo.h>
+#include <linux/tty_flip.h>
+#include <linux/timer.h>
+#include <linux/serial.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+#include <linux/rfkill.h>
+#include <linux/fs.h>
+#include <linux/ip.h>
+#include <linux/dmapool.h>
+#include <linux/gpio.h>
+#include <linux/sched.h>
+#include <linux/time.h>
+#include <linux/wait.h>
+#include <linux/tty.h>
+#include <linux/pm.h>
+#include <linux/pm_runtime.h>
+#include <linux/spi/ifx_modem.h>
+
+#include "ifx6x60.h"
+
+#define IFX_SPI_MORE_MASK 0x10
+#define IFX_SPI_MORE_BIT 12 /* bit position in u16 */
+#define IFX_SPI_CTS_BIT 13 /* bit position in u16 */
+#define IFX_SPI_TTY_ID 0
+#define IFX_SPI_TIMEOUT_SEC 2
+#define IFX_SPI_HEADER_0 (-1)
+#define IFX_SPI_HEADER_F (-2)
+
+/* forward reference */
+static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev);
+
+/* local variables */
+static int spi_b16 = 1; /* 8 or 16 bit word length */
+static struct tty_driver *tty_drv;
+static struct ifx_spi_device *saved_ifx_dev;
+static struct lock_class_key ifx_spi_key;
+
+/* GPIO/GPE settings */
+
+/**
+ * mrdy_set_high - set MRDY GPIO
+ * @ifx: device we are controlling
+ *
+ */
+static inline void mrdy_set_high(struct ifx_spi_device *ifx)
+{
+ gpio_set_value(ifx->gpio.mrdy, 1);
+}
+
+/**
+ * mrdy_set_low - clear MRDY GPIO
+ * @ifx: device we are controlling
+ *
+ */
+static inline void mrdy_set_low(struct ifx_spi_device *ifx)
+{
+ gpio_set_value(ifx->gpio.mrdy, 0);
+}
+
+/**
+ * ifx_spi_power_state_set
+ * @ifx_dev: our SPI device
+ * @val: bits to set
+ *
+ * Set bit in power status and signal power system if status becomes non-0
+ */
+static void
+ifx_spi_power_state_set(struct ifx_spi_device *ifx_dev, unsigned char val)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&ifx_dev->power_lock, flags);
+
+ /*
+ * if power status is already non-0, just update, else
+ * tell power system
+ */
+ if (!ifx_dev->power_status)
+ pm_runtime_get(&ifx_dev->spi_dev->dev);
+ ifx_dev->power_status |= val;
+
+ spin_unlock_irqrestore(&ifx_dev->power_lock, flags);
+}
+
+/**
+ * ifx_spi_power_state_clear - clear power bit
+ * @ifx_dev: our SPI device
+ * @val: bits to clear
+ *
+ * clear bit in power status and signal power system if status becomes 0
+ */
+static void
+ifx_spi_power_state_clear(struct ifx_spi_device *ifx_dev, unsigned char val)
+{
+ unsigned long flags;
+
+ spin_lock_irqsave(&ifx_dev->power_lock, flags);
+
+ if (ifx_dev->power_status) {
+ ifx_dev->power_status &= ~val;
+ if (!ifx_dev->power_status)
+ pm_runtime_put(&ifx_dev->spi_dev->dev);
+ }
+
+ spin_unlock_irqrestore(&ifx_dev->power_lock, flags);
+}
+
+/**
+ * swap_buf
+ * @buf: our buffer
+ * @len : number of bytes (not words) in the buffer
+ * @end: end of buffer
+ *
+ * Swap the contents of a buffer into big endian format
+ */
+static inline void swap_buf(u16 *buf, int len, void *end)
+{
+ int n;
+
+ len = ((len + 1) >> 1);
+ if ((void *)&buf[len] > end) {
+ pr_err("swap_buf: swap exceeds boundary (%p > %p)!",
+ &buf[len], end);
+ return;
+ }
+ for (n = 0; n < len; n++) {
+ *buf = cpu_to_be16(*buf);
+ buf++;
+ }
+}
+
+/**
+ * mrdy_assert - assert MRDY line
+ * @ifx_dev: our SPI device
+ *
+ * Assert mrdy and set timer to wait for SRDY interrupt, if SRDY is low
+ * now.
+ *
+ * FIXME: Can SRDY even go high as we are running this code ?
+ */
+static void mrdy_assert(struct ifx_spi_device *ifx_dev)
+{
+ int val = gpio_get_value(ifx_dev->gpio.srdy);
+ if (!val) {
+ if (!test_and_set_bit(IFX_SPI_STATE_TIMER_PENDING,
+ &ifx_dev->flags)) {
+ ifx_dev->spi_timer.expires =
+ jiffies + IFX_SPI_TIMEOUT_SEC*HZ;
+ add_timer(&ifx_dev->spi_timer);
+
+ }
+ }
+ ifx_spi_power_state_set(ifx_dev, IFX_SPI_POWER_DATA_PENDING);
+ mrdy_set_high(ifx_dev);
+}
+
+/**
+ * ifx_spi_hangup - hang up an IFX device
+ * @ifx_dev: our SPI device
+ *
+ * Hang up the tty attached to the IFX device if one is currently
+ * open. If not take no action
+ */
+static void ifx_spi_ttyhangup(struct ifx_spi_device *ifx_dev)
+{
+ struct tty_port *pport = &ifx_dev->tty_port;
+ struct tty_struct *tty = tty_port_tty_get(pport);
+ if (tty) {
+ tty_hangup(tty);
+ tty_kref_put(tty);
+ }
+}
+
+/**
+ * ifx_spi_timeout - SPI timeout
+ * @arg: our SPI device
+ *
+ * The SPI has timed out: hang up the tty. Users will then see a hangup
+ * and error events.
+ */
+static void ifx_spi_timeout(unsigned long arg)
+{
+ struct ifx_spi_device *ifx_dev = (struct ifx_spi_device *)arg;
+
+ dev_warn(&ifx_dev->spi_dev->dev, "*** SPI Timeout ***");
+ ifx_spi_ttyhangup(ifx_dev);
+ mrdy_set_low(ifx_dev);
+ clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
+}
+
+/* char/tty operations */
+
+/**
+ * ifx_spi_tiocmget - get modem lines
+ * @tty: our tty device
+ * @filp: file handle issuing the request
+ *
+ * Map the signal state into Linux modem flags and report the value
+ * in Linux terms
+ */
+static int ifx_spi_tiocmget(struct tty_struct *tty, struct file *filp)
+{
+ unsigned int value;
+ struct ifx_spi_device *ifx_dev = tty->driver_data;
+
+ value =
+ (test_bit(IFX_SPI_RTS, &ifx_dev->signal_state) ? TIOCM_RTS : 0) |
+ (test_bit(IFX_SPI_DTR, &ifx_dev->signal_state) ? TIOCM_DTR : 0) |
+ (test_bit(IFX_SPI_CTS, &ifx_dev->signal_state) ? TIOCM_CTS : 0) |
+ (test_bit(IFX_SPI_DSR, &ifx_dev->signal_state) ? TIOCM_DSR : 0) |
+ (test_bit(IFX_SPI_DCD, &ifx_dev->signal_state) ? TIOCM_CAR : 0) |
+ (test_bit(IFX_SPI_RI, &ifx_dev->signal_state) ? TIOCM_RNG : 0);
+ return value;
+}
+
+/**
+ * ifx_spi_tiocmset - set modem bits
+ * @tty: the tty structure
+ * @filp: file handle issuing the request
+ * @set: bits to set
+ * @clear: bits to clear
+ *
+ * The IFX6x60 only supports DTR and RTS. Set them accordingly
+ * and flag that an update to the modem is needed.
+ *
+ * FIXME: do we need to kick the tranfers when we do this ?
+ */
+static int ifx_spi_tiocmset(struct tty_struct *tty, struct file *filp,
+ unsigned int set, unsigned int clear)
+{
+ struct ifx_spi_device *ifx_dev = tty->driver_data;
+
+ if (set & TIOCM_RTS)
+ set_bit(IFX_SPI_RTS, &ifx_dev->signal_state);
+ if (set & TIOCM_DTR)
+ set_bit(IFX_SPI_DTR, &ifx_dev->signal_state);
+ if (clear & TIOCM_RTS)
+ clear_bit(IFX_SPI_RTS, &ifx_dev->signal_state);
+ if (clear & TIOCM_DTR)
+ clear_bit(IFX_SPI_DTR, &ifx_dev->signal_state);
+
+ set_bit(IFX_SPI_UPDATE, &ifx_dev->signal_state);
+ return 0;
+}
+
+/**
+ * ifx_spi_open - called on tty open
+ * @tty: our tty device
+ * @filp: file handle being associated with the tty
+ *
+ * Open the tty interface. We let the tty_port layer do all the work
+ * for us.
+ *
+ * FIXME: Remove single device assumption and saved_ifx_dev
+ */
+static int ifx_spi_open(struct tty_struct *tty, struct file *filp)
+{
+ return tty_port_open(&saved_ifx_dev->tty_port, tty, filp);
+}
+
+/**
+ * ifx_spi_close - called when our tty closes
+ * @tty: the tty being closed
+ * @filp: the file handle being closed
+ *
+ * Perform the close of the tty. We use the tty_port layer to do all
+ * our hard work.
+ */
+static void ifx_spi_close(struct tty_struct *tty, struct file *filp)
+{
+ struct ifx_spi_device *ifx_dev = tty->driver_data;
+ tty_port_close(&ifx_dev->tty_port, tty, filp);
+ /* FIXME: should we do an ifx_spi_reset here ? */
+}
+
+/**
+ * ifx_decode_spi_header - decode received header
+ * @buffer: the received data
+ * @length: decoded length
+ * @more: decoded more flag
+ * @received_cts: status of cts we received
+ *
+ * Note how received_cts is handled -- if header is all F it is left
+ * the same as it was, if header is all 0 it is set to 0 otherwise it is
+ * taken from the incoming header.
+ *
+ * FIXME: endianness
+ */
+static int ifx_spi_decode_spi_header(unsigned char *buffer, int *length,
+ unsigned char *more, unsigned char *received_cts)
+{
+ u16 h1;
+ u16 h2;
+ u16 *in_buffer = (u16 *)buffer;
+
+ h1 = *in_buffer;
+ h2 = *(in_buffer+1);
+
+ if (h1 == 0 && h2 == 0) {
+ *received_cts = 0;
+ return IFX_SPI_HEADER_0;
+ } else if (h1 == 0xffff && h2 == 0xffff) {
+ /* spi_slave_cts remains as it was */
+ return IFX_SPI_HEADER_F;
+ }
+
+ *length = h1 & 0xfff; /* upper bits of byte are flags */
+ *more = (buffer[1] >> IFX_SPI_MORE_BIT) & 1;
+ *received_cts = (buffer[3] >> IFX_SPI_CTS_BIT) & 1;
+ return 0;
+}
+
+/**
+ * ifx_setup_spi_header - set header fields
+ * @txbuffer: pointer to start of SPI buffer
+ * @tx_count: bytes
+ * @more: indicate if more to follow
+ *
+ * Format up an SPI header for a transfer
+ *
+ * FIXME: endianness?
+ */
+static void ifx_spi_setup_spi_header(unsigned char *txbuffer, int tx_count,
+ unsigned char more)
+{
+ *(u16 *)(txbuffer) = tx_count;
+ *(u16 *)(txbuffer+2) = IFX_SPI_PAYLOAD_SIZE;
+ txbuffer[1] |= (more << IFX_SPI_MORE_BIT) & IFX_SPI_MORE_MASK;
+}
+
+/**
+ * ifx_spi_wakeup_serial - SPI space made
+ * @port_data: our SPI device
+ *
+ * We have emptied the FIFO enough that we want to get more data
+ * queued into it. Poke the line discipline via tty_wakeup so that
+ * it will feed us more bits
+ */
+static void ifx_spi_wakeup_serial(struct ifx_spi_device *ifx_dev)
+{
+ struct tty_struct *tty;
+
+ tty = tty_port_tty_get(&ifx_dev->tty_port);
+ if (!tty)
+ return;
+ tty_wakeup(tty);
+ tty_kref_put(tty);
+}
+
+/**
+ * ifx_spi_prepare_tx_buffer - prepare transmit frame
+ * @ifx_dev: our SPI device
+ *
+ * The transmit buffr needs a header and various other bits of
+ * information followed by as much data as we can pull from the FIFO
+ * and transfer. This function formats up a suitable buffer in the
+ * ifx_dev->tx_buffer
+ *
+ * FIXME: performance - should we wake the tty when the queue is half
+ * empty ?
+ */
+static int ifx_spi_prepare_tx_buffer(struct ifx_spi_device *ifx_dev)
+{
+ int temp_count;
+ int queue_length;
+ int tx_count;
+ unsigned char *tx_buffer;
+
+ tx_buffer = ifx_dev->tx_buffer;
+ memset(tx_buffer, 0, IFX_SPI_TRANSFER_SIZE);
+
+ /* make room for required SPI header */
+ tx_buffer += IFX_SPI_HEADER_OVERHEAD;
+ tx_count = IFX_SPI_HEADER_OVERHEAD;
+
+ /* clear to signal no more data if this turns out to be the
+ * last buffer sent in a sequence */
+ ifx_dev->spi_more = 0;
+
+ /* if modem cts is set, just send empty buffer */
+ if (!ifx_dev->spi_slave_cts) {
+ /* see if there's tx data */
+ queue_length = kfifo_len(&ifx_dev->tx_fifo);
+ if (queue_length != 0) {
+ /* data to mux -- see if there's room for it */
+ temp_count = min(queue_length, IFX_SPI_PAYLOAD_SIZE);
+ temp_count = kfifo_out_locked(&ifx_dev->tx_fifo,
+ tx_buffer, temp_count,
+ &ifx_dev->fifo_lock);
+
+ /* update buffer pointer and data count in message */
+ tx_buffer += temp_count;
+ tx_count += temp_count;
+ if (temp_count == queue_length)
+ /* poke port to get more data */
+ ifx_spi_wakeup_serial(ifx_dev);
+ else /* more data in port, use next SPI message */
+ ifx_dev->spi_more = 1;
+ }
+ }
+ /* have data and info for header -- set up SPI header in buffer */
+ /* spi header needs payload size, not entire buffer size */
+ ifx_spi_setup_spi_header(ifx_dev->tx_buffer,
+ tx_count-IFX_SPI_HEADER_OVERHEAD,
+ ifx_dev->spi_more);
+ /* swap actual data in the buffer */
+ swap_buf((u16 *)(ifx_dev->tx_buffer), tx_count,
+ &ifx_dev->tx_buffer[IFX_SPI_TRANSFER_SIZE]);
+ return tx_count;
+}
+
+/**
+ * ifx_spi_write - line discipline write
+ * @tty: our tty device
+ * @buf: pointer to buffer to write (kernel space)
+ * @count: size of buffer
+ *
+ * Write the characters we have been given into the FIFO. If the device
+ * is not active then activate it, when the SRDY line is asserted back
+ * this will commence I/O
+ */
+static int ifx_spi_write(struct tty_struct *tty, const unsigned char *buf,
+ int count)
+{
+ struct ifx_spi_device *ifx_dev = tty->driver_data;
+ unsigned char *tmp_buf = (unsigned char *)buf;
+ int tx_count = kfifo_in_locked(&ifx_dev->tx_fifo, tmp_buf, count,
+ &ifx_dev->fifo_lock);
+ mrdy_assert(ifx_dev);
+ return tx_count;
+}
+
+/**
+ * ifx_spi_chars_in_buffer - line discipline helper
+ * @tty: our tty device
+ *
+ * Report how much data we can accept before we drop bytes. As we use
+ * a simple FIFO this is nice and easy.
+ */
+static int ifx_spi_write_room(struct tty_struct *tty)
+{
+ struct ifx_spi_device *ifx_dev = tty->driver_data;
+ return IFX_SPI_FIFO_SIZE - kfifo_len(&ifx_dev->tx_fifo);
+}
+
+/**
+ * ifx_spi_chars_in_buffer - line discipline helper
+ * @tty: our tty device
+ *
+ * Report how many characters we have buffered. In our case this is the
+ * number of bytes sitting in our transmit FIFO.
+ */
+static int ifx_spi_chars_in_buffer(struct tty_struct *tty)
+{
+ struct ifx_spi_device *ifx_dev = tty->driver_data;
+ return kfifo_len(&ifx_dev->tx_fifo);
+}
+
+/**
+ * ifx_port_hangup
+ * @port: our tty port
+ *
+ * tty port hang up. Called when tty_hangup processing is invoked either
+ * by loss of carrier, or by software (eg vhangup). Serialized against
+ * activate/shutdown by the tty layer.
+ */
+static void ifx_spi_hangup(struct tty_struct *tty)
+{
+ struct ifx_spi_device *ifx_dev = tty->driver_data;
+ tty_port_hangup(&ifx_dev->tty_port);
+}
+
+/**
+ * ifx_port_activate
+ * @port: our tty port
+ *
+ * tty port activate method - called for first open. Serialized
+ * with hangup and shutdown by the tty layer.
+ */
+static int ifx_port_activate(struct tty_port *port, struct tty_struct *tty)
+{
+ struct ifx_spi_device *ifx_dev =
+ container_of(port, struct ifx_spi_device, tty_port);
+
+ /* clear any old data; can't do this in 'close' */
+ kfifo_reset(&ifx_dev->tx_fifo);
+
+ /* put port data into this tty */
+ tty->driver_data = ifx_dev;
+
+ /* allows flip string push from int context */
+ tty->low_latency = 1;
+
+ return 0;
+}
+
+/**
+ * ifx_port_shutdown
+ * @port: our tty port
+ *
+ * tty port shutdown method - called for last port close. Serialized
+ * with hangup and activate by the tty layer.
+ */
+static void ifx_port_shutdown(struct tty_port *port)
+{
+ struct ifx_spi_device *ifx_dev =
+ container_of(port, struct ifx_spi_device, tty_port);
+
+ mrdy_set_low(ifx_dev);
+ clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
+ tasklet_kill(&ifx_dev->io_work_tasklet);
+}
+
+static const struct tty_port_operations ifx_tty_port_ops = {
+ .activate = ifx_port_activate,
+ .shutdown = ifx_port_shutdown,
+};
+
+static const struct tty_operations ifx_spi_serial_ops = {
+ .open = ifx_spi_open,
+ .close = ifx_spi_close,
+ .write = ifx_spi_write,
+ .hangup = ifx_spi_hangup,
+ .write_room = ifx_spi_write_room,
+ .chars_in_buffer = ifx_spi_chars_in_buffer,
+ .tiocmget = ifx_spi_tiocmget,
+ .tiocmset = ifx_spi_tiocmset,
+};
+
+/**
+ * ifx_spi_insert_fip_string - queue received data
+ * @ifx_ser: our SPI device
+ * @chars: buffer we have received
+ * @size: number of chars reeived
+ *
+ * Queue bytes to the tty assuming the tty side is currently open. If
+ * not the discard the data.
+ */
+static void ifx_spi_insert_flip_string(struct ifx_spi_device *ifx_dev,
+ unsigned char *chars, size_t size)
+{
+ struct tty_struct *tty = tty_port_tty_get(&ifx_dev->tty_port);
+ if (!tty)
+ return;
+ tty_insert_flip_string(tty, chars, size);
+ tty_flip_buffer_push(tty);
+ tty_kref_put(tty);
+}
+
+/**
+ * ifx_spi_complete - SPI transfer completed
+ * @ctx: our SPI device
+ *
+ * An SPI transfer has completed. Process any received data and kick off
+ * any further transmits we can commence.
+ */
+static void ifx_spi_complete(void *ctx)
+{
+ struct ifx_spi_device *ifx_dev = ctx;
+ struct tty_struct *tty;
+ struct tty_ldisc *ldisc = NULL;
+ int length;
+ int actual_length;
+ unsigned char more;
+ unsigned char cts;
+ int local_write_pending = 0;
+ int queue_length;
+ int srdy;
+ int decode_result;
+
+ mrdy_set_low(ifx_dev);
+
+ if (!ifx_dev->spi_msg.status) {
+ /* check header validity, get comm flags */
+ swap_buf((u16 *)ifx_dev->rx_buffer, IFX_SPI_HEADER_OVERHEAD,
+ &ifx_dev->rx_buffer[IFX_SPI_HEADER_OVERHEAD]);
+ decode_result = ifx_spi_decode_spi_header(ifx_dev->rx_buffer,
+ &length, &more, &cts);
+ if (decode_result == IFX_SPI_HEADER_0) {
+ dev_dbg(&ifx_dev->spi_dev->dev,
+ "ignore input: invalid header 0");
+ ifx_dev->spi_slave_cts = 0;
+ goto complete_exit;
+ } else if (decode_result == IFX_SPI_HEADER_F) {
+ dev_dbg(&ifx_dev->spi_dev->dev,
+ "ignore input: invalid header F");
+ goto complete_exit;
+ }
+
+ ifx_dev->spi_slave_cts = cts;
+
+ actual_length = min((unsigned int)length,
+ ifx_dev->spi_msg.actual_length);
+ swap_buf((u16 *)(ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD),
+ actual_length,
+ &ifx_dev->rx_buffer[IFX_SPI_TRANSFER_SIZE]);
+ ifx_spi_insert_flip_string(
+ ifx_dev,
+ ifx_dev->rx_buffer + IFX_SPI_HEADER_OVERHEAD,
+ (size_t)actual_length);
+ } else {
+ dev_dbg(&ifx_dev->spi_dev->dev, "SPI transfer error %d",
+ ifx_dev->spi_msg.status);
+ }
+
+complete_exit:
+ if (ifx_dev->write_pending) {
+ ifx_dev->write_pending = 0;
+ local_write_pending = 1;
+ }
+
+ clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &(ifx_dev->flags));
+
+ queue_length = kfifo_len(&ifx_dev->tx_fifo);
+ srdy = gpio_get_value(ifx_dev->gpio.srdy);
+ if (!srdy)
+ ifx_spi_power_state_clear(ifx_dev, IFX_SPI_POWER_SRDY);
+
+ /* schedule output if there is more to do */
+ if (test_and_clear_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags))
+ tasklet_schedule(&ifx_dev->io_work_tasklet);
+ else {
+ if (more || ifx_dev->spi_more || queue_length > 0 ||
+ local_write_pending) {
+ if (ifx_dev->spi_slave_cts) {
+ if (more)
+ mrdy_assert(ifx_dev);
+ } else
+ mrdy_assert(ifx_dev);
+ } else {
+ /*
+ * poke line discipline driver if any for more data
+ * may or may not get more data to write
+ * for now, say not busy
+ */
+ ifx_spi_power_state_clear(ifx_dev,
+ IFX_SPI_POWER_DATA_PENDING);
+ tty = tty_port_tty_get(&ifx_dev->tty_port);
+ if (tty) {
+ ldisc = tty_ldisc_ref(tty);
+ if (ldisc) {
+ ldisc->ops->write_wakeup(tty);
+ tty_ldisc_deref(ldisc);
+ }
+ tty_kref_put(tty);
+ }
+ }
+ }
+}
+
+/**
+ * ifx_spio_io - I/O tasklet
+ * @data: our SPI device
+ *
+ * Queue data for transmission if possible and then kick off the
+ * transfer.
+ */
+static void ifx_spi_io(unsigned long data)
+{
+ int retval;
+ struct ifx_spi_device *ifx_dev = (struct ifx_spi_device *) data;
+
+ if (!test_and_set_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags)) {
+ if (ifx_dev->gpio.unack_srdy_int_nb > 0)
+ ifx_dev->gpio.unack_srdy_int_nb--;
+
+ ifx_spi_prepare_tx_buffer(ifx_dev);
+
+ spi_message_init(&ifx_dev->spi_msg);
+ INIT_LIST_HEAD(&ifx_dev->spi_msg.queue);
+
+ ifx_dev->spi_msg.context = ifx_dev;
+ ifx_dev->spi_msg.complete = ifx_spi_complete;
+
+ /* set up our spi transfer */
+ /* note len is BYTES, not transfers */
+ ifx_dev->spi_xfer.len = IFX_SPI_TRANSFER_SIZE;
+ ifx_dev->spi_xfer.cs_change = 0;
+ ifx_dev->spi_xfer.speed_hz = 12500000;
+ /* ifx_dev->spi_xfer.speed_hz = 390625; */
+ ifx_dev->spi_xfer.bits_per_word = spi_b16 ? 16 : 8;
+
+ ifx_dev->spi_xfer.tx_buf = ifx_dev->tx_buffer;
+ ifx_dev->spi_xfer.rx_buf = ifx_dev->rx_buffer;
+
+ /*
+ * setup dma pointers
+ */
+ if (ifx_dev->is_6160) {
+ ifx_dev->spi_msg.is_dma_mapped = 1;
+ ifx_dev->tx_dma = ifx_dev->tx_bus;
+ ifx_dev->rx_dma = ifx_dev->rx_bus;
+ ifx_dev->spi_xfer.tx_dma = ifx_dev->tx_dma;
+ ifx_dev->spi_xfer.rx_dma = ifx_dev->rx_dma;
+ } else {
+ ifx_dev->spi_msg.is_dma_mapped = 0;
+ ifx_dev->tx_dma = (dma_addr_t)0;
+ ifx_dev->rx_dma = (dma_addr_t)0;
+ ifx_dev->spi_xfer.tx_dma = (dma_addr_t)0;
+ ifx_dev->spi_xfer.rx_dma = (dma_addr_t)0;
+ }
+
+ spi_message_add_tail(&ifx_dev->spi_xfer, &ifx_dev->spi_msg);
+
+ /* Assert MRDY. This may have already been done by the write
+ * routine.
+ */
+ mrdy_assert(ifx_dev);
+
+ retval = spi_async(ifx_dev->spi_dev, &ifx_dev->spi_msg);
+ if (retval) {
+ clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS,
+ &ifx_dev->flags);
+ tasklet_schedule(&ifx_dev->io_work_tasklet);
+ return;
+ }
+ } else
+ ifx_dev->write_pending = 1;
+}
+
+/**
+ * ifx_spi_free_port - free up the tty side
+ * @ifx_dev: IFX device going away
+ *
+ * Unregister and free up a port when the device goes away
+ */
+static void ifx_spi_free_port(struct ifx_spi_device *ifx_dev)
+{
+ if (ifx_dev->tty_dev)
+ tty_unregister_device(tty_drv, ifx_dev->minor);
+ kfifo_free(&ifx_dev->tx_fifo);
+}
+
+/**
+ * ifx_spi_create_port - create a new port
+ * @ifx_dev: our spi device
+ *
+ * Allocate and initialise the tty port that goes with this interface
+ * and add it to the tty layer so that it can be opened.
+ */
+static int ifx_spi_create_port(struct ifx_spi_device *ifx_dev)
+{
+ int ret = 0;
+ struct tty_port *pport = &ifx_dev->tty_port;
+
+ spin_lock_init(&ifx_dev->fifo_lock);
+ lockdep_set_class_and_subclass(&ifx_dev->fifo_lock,
+ &ifx_spi_key, 0);
+
+ if (kfifo_alloc(&ifx_dev->tx_fifo, IFX_SPI_FIFO_SIZE, GFP_KERNEL)) {
+ ret = -ENOMEM;
+ goto error_ret;
+ }
+
+ pport->ops = &ifx_tty_port_ops;
+ tty_port_init(pport);
+ ifx_dev->minor = IFX_SPI_TTY_ID;
+ ifx_dev->tty_dev = tty_register_device(tty_drv, ifx_dev->minor,
+ &ifx_dev->spi_dev->dev);
+ if (IS_ERR(ifx_dev->tty_dev)) {
+ dev_dbg(&ifx_dev->spi_dev->dev,
+ "%s: registering tty device failed", __func__);
+ ret = PTR_ERR(ifx_dev->tty_dev);
+ goto error_ret;
+ }
+ return 0;
+
+error_ret:
+ ifx_spi_free_port(ifx_dev);
+ return ret;
+}
+
+/**
+ * ifx_spi_handle_srdy - handle SRDY
+ * @ifx_dev: device asserting SRDY
+ *
+ * Check our device state and see what we need to kick off when SRDY
+ * is asserted. This usually means killing the timer and firing off the
+ * I/O processing.
+ */
+static void ifx_spi_handle_srdy(struct ifx_spi_device *ifx_dev)
+{
+ if (test_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags)) {
+ del_timer_sync(&ifx_dev->spi_timer);
+ clear_bit(IFX_SPI_STATE_TIMER_PENDING, &ifx_dev->flags);
+ }
+
+ ifx_spi_power_state_set(ifx_dev, IFX_SPI_POWER_SRDY);
+
+ if (!test_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags))
+ tasklet_schedule(&ifx_dev->io_work_tasklet);
+ else
+ set_bit(IFX_SPI_STATE_IO_READY, &ifx_dev->flags);
+}
+
+/**
+ * ifx_spi_srdy_interrupt - SRDY asserted
+ * @irq: our IRQ number
+ * @dev: our ifx device
+ *
+ * The modem asserted SRDY. Handle the srdy event
+ */
+static irqreturn_t ifx_spi_srdy_interrupt(int irq, void *dev)
+{
+ struct ifx_spi_device *ifx_dev = dev;
+ ifx_dev->gpio.unack_srdy_int_nb++;
+ ifx_spi_handle_srdy(ifx_dev);
+ return IRQ_HANDLED;
+}
+
+/**
+ * ifx_spi_reset_interrupt - Modem has changed reset state
+ * @irq: interrupt number
+ * @dev: our device pointer
+ *
+ * The modem has either entered or left reset state. Check the GPIO
+ * line to see which.
+ *
+ * FIXME: review locking on MR_INPROGRESS versus
+ * parallel unsolicited reset/solicited reset
+ */
+static irqreturn_t ifx_spi_reset_interrupt(int irq, void *dev)
+{
+ struct ifx_spi_device *ifx_dev = dev;
+ int val = gpio_get_value(ifx_dev->gpio.reset_out);
+ int solreset = test_bit(MR_START, &ifx_dev->mdm_reset_state);
+
+ if (val == 0) {
+ /* entered reset */
+ set_bit(MR_INPROGRESS, &ifx_dev->mdm_reset_state);
+ if (!solreset) {
+ /* unsolicited reset */
+ ifx_spi_ttyhangup(ifx_dev);
+ }
+ } else {
+ /* exited reset */
+ clear_bit(MR_INPROGRESS, &ifx_dev->mdm_reset_state);
+ if (solreset) {
+ set_bit(MR_COMPLETE, &ifx_dev->mdm_reset_state);
+ wake_up(&ifx_dev->mdm_reset_wait);
+ }
+ }
+ return IRQ_HANDLED;
+}
+
+/**
+ * ifx_spi_free_device - free device
+ * @ifx_dev: device to free
+ *
+ * Free the IFX device
+ */
+static void ifx_spi_free_device(struct ifx_spi_device *ifx_dev)
+{
+ ifx_spi_free_port(ifx_dev);
+ dma_free_coherent(&ifx_dev->spi_dev->dev,
+ IFX_SPI_TRANSFER_SIZE,
+ ifx_dev->tx_buffer,
+ ifx_dev->tx_bus);
+ dma_free_coherent(&ifx_dev->spi_dev->dev,
+ IFX_SPI_TRANSFER_SIZE,
+ ifx_dev->rx_buffer,
+ ifx_dev->rx_bus);
+}
+
+/**
+ * ifx_spi_reset - reset modem
+ * @ifx_dev: modem to reset
+ *
+ * Perform a reset on the modem
+ */
+static int ifx_spi_reset(struct ifx_spi_device *ifx_dev)
+{
+ int ret;
+ /*
+ * set up modem power, reset
+ *
+ * delays are required on some platforms for the modem
+ * to reset properly
+ */
+ set_bit(MR_START, &ifx_dev->mdm_reset_state);
+ gpio_set_value(ifx_dev->gpio.po, 0);
+ gpio_set_value(ifx_dev->gpio.reset, 0);
+ msleep(25);
+ gpio_set_value(ifx_dev->gpio.reset, 1);
+ msleep(1);
+ gpio_set_value(ifx_dev->gpio.po, 1);
+ msleep(1);
+ gpio_set_value(ifx_dev->gpio.po, 0);
+ ret = wait_event_timeout(ifx_dev->mdm_reset_wait,
+ test_bit(MR_COMPLETE,
+ &ifx_dev->mdm_reset_state),
+ IFX_RESET_TIMEOUT);
+ if (!ret)
+ dev_warn(&ifx_dev->spi_dev->dev, "Modem reset timeout: (state:%lx)",
+ ifx_dev->mdm_reset_state);
+
+ ifx_dev->mdm_reset_state = 0;
+ return ret;
+}
+
+/**
+ * ifx_spi_spi_probe - probe callback
+ * @spi: our possible matching SPI device
+ *
+ * Probe for a 6x60 modem on SPI bus. Perform any needed device and
+ * GPIO setup.
+ *
+ * FIXME:
+ * - Support for multiple devices
+ * - Split out MID specific GPIO handling eventually
+ */
+
+static int ifx_spi_spi_probe(struct spi_device *spi)
+{
+ int ret;
+ int srdy;
+ struct ifx_modem_platform_data *pl_data = NULL;
+ struct ifx_spi_device *ifx_dev;
+
+ if (saved_ifx_dev) {
+ dev_dbg(&spi->dev, "ignoring subsequent detection");
+ return -ENODEV;
+ }
+
+ /* initialize structure to hold our device variables */
+ ifx_dev = kzalloc(sizeof(struct ifx_spi_device), GFP_KERNEL);
+ if (!ifx_dev) {
+ dev_err(&spi->dev, "spi device allocation failed");
+ return -ENOMEM;
+ }
+ saved_ifx_dev = ifx_dev;
+ ifx_dev->spi_dev = spi;
+ clear_bit(IFX_SPI_STATE_IO_IN_PROGRESS, &ifx_dev->flags);
+ spin_lock_init(&ifx_dev->write_lock);
+ spin_lock_init(&ifx_dev->power_lock);
+ ifx_dev->power_status = 0;
+ init_timer(&ifx_dev->spi_timer);
+ ifx_dev->spi_timer.function = ifx_spi_timeout;
+ ifx_dev->spi_timer.data = (unsigned long)ifx_dev;
+ ifx_dev->is_6160 = pl_data->is_6160;
+
+ /* ensure SPI protocol flags are initialized to enable transfer */
+ ifx_dev->spi_more = 0;
+ ifx_dev->spi_slave_cts = 0;
+
+ /*initialize transfer and dma buffers */
+ ifx_dev->tx_buffer = dma_alloc_coherent(&ifx_dev->spi_dev->dev,
+ IFX_SPI_TRANSFER_SIZE,
+ &ifx_dev->tx_bus,
+ GFP_KERNEL);
+ if (!ifx_dev->tx_buffer) {
+ dev_err(&spi->dev, "DMA-TX buffer allocation failed");
+ ret = -ENOMEM;
+ goto error_ret;
+ }
+ ifx_dev->rx_buffer = dma_alloc_coherent(&ifx_dev->spi_dev->dev,
+ IFX_SPI_TRANSFER_SIZE,
+ &ifx_dev->rx_bus,
+ GFP_KERNEL);
+ if (!ifx_dev->rx_buffer) {
+ dev_err(&spi->dev, "DMA-RX buffer allocation failed");
+ ret = -ENOMEM;
+ goto error_ret;
+ }
+
+ /* initialize waitq for modem reset */
+ init_waitqueue_head(&ifx_dev->mdm_reset_wait);
+
+ spi_set_drvdata(spi, ifx_dev);
+ tasklet_init(&ifx_dev->io_work_tasklet, ifx_spi_io,
+ (unsigned long)ifx_dev);
+
+ set_bit(IFX_SPI_STATE_PRESENT, &ifx_dev->flags);
+
+ /* create our tty port */
+ ret = ifx_spi_create_port(ifx_dev);
+ if (ret != 0) {
+ dev_err(&spi->dev, "create default tty port failed");
+ goto error_ret;
+ }
+
+ pl_data = (struct ifx_modem_platform_data *)spi->dev.platform_data;
+ if (pl_data) {
+ ifx_dev->gpio.reset = pl_data->rst_pmu;
+ ifx_dev->gpio.po = pl_data->pwr_on;
+ ifx_dev->gpio.mrdy = pl_data->mrdy;
+ ifx_dev->gpio.srdy = pl_data->srdy;
+ ifx_dev->gpio.reset_out = pl_data->rst_out;
+ } else {
+ dev_err(&spi->dev, "missing platform data!");
+ ret = -ENODEV;
+ goto error_ret;
+ }
+
+ dev_info(&spi->dev, "gpios %d, %d, %d, %d, %d",
+ ifx_dev->gpio.reset, ifx_dev->gpio.po, ifx_dev->gpio.mrdy,
+ ifx_dev->gpio.srdy, ifx_dev->gpio.reset_out);
+
+ /* Configure gpios */
+ ret = gpio_request(ifx_dev->gpio.reset, "ifxModem");
+ if (ret < 0) {
+ dev_err(&spi->dev, "Unable to allocate GPIO%d (RESET)",
+ ifx_dev->gpio.reset);
+ goto error_ret;
+ }
+ ret += gpio_direction_output(ifx_dev->gpio.reset, 0);
+ ret += gpio_export(ifx_dev->gpio.reset, 1);
+ if (ret) {
+ dev_err(&spi->dev, "Unable to configure GPIO%d (RESET)",
+ ifx_dev->gpio.reset);
+ ret = -EBUSY;
+ goto error_ret2;
+ }
+
+ ret = gpio_request(ifx_dev->gpio.po, "ifxModem");
+ ret += gpio_direction_output(ifx_dev->gpio.po, 0);
+ ret += gpio_export(ifx_dev->gpio.po, 1);
+ if (ret) {
+ dev_err(&spi->dev, "Unable to configure GPIO%d (ON)",
+ ifx_dev->gpio.po);
+ ret = -EBUSY;
+ goto error_ret3;
+ }
+
+ ret = gpio_request(ifx_dev->gpio.mrdy, "ifxModem");
+ if (ret < 0) {
+ dev_err(&spi->dev, "Unable to allocate GPIO%d (MRDY)",
+ ifx_dev->gpio.mrdy);
+ goto error_ret3;
+ }
+ ret += gpio_export(ifx_dev->gpio.mrdy, 1);
+ ret += gpio_direction_output(ifx_dev->gpio.mrdy, 0);
+ if (ret) {
+ dev_err(&spi->dev, "Unable to configure GPIO%d (MRDY)",
+ ifx_dev->gpio.mrdy);
+ ret = -EBUSY;
+ goto error_ret4;
+ }
+
+ ret = gpio_request(ifx_dev->gpio.srdy, "ifxModem");
+ if (ret < 0) {
+ dev_err(&spi->dev, "Unable to allocate GPIO%d (SRDY)",
+ ifx_dev->gpio.srdy);
+ ret = -EBUSY;
+ goto error_ret4;
+ }
+ ret += gpio_export(ifx_dev->gpio.srdy, 1);
+ ret += gpio_direction_input(ifx_dev->gpio.srdy);
+ if (ret) {
+ dev_err(&spi->dev, "Unable to configure GPIO%d (SRDY)",
+ ifx_dev->gpio.srdy);
+ ret = -EBUSY;
+ goto error_ret5;
+ }
+
+ ret = gpio_request(ifx_dev->gpio.reset_out, "ifxModem");
+ if (ret < 0) {
+ dev_err(&spi->dev, "Unable to allocate GPIO%d (RESET_OUT)",
+ ifx_dev->gpio.reset_out);
+ goto error_ret5;
+ }
+ ret += gpio_export(ifx_dev->gpio.reset_out, 1);
+ ret += gpio_direction_input(ifx_dev->gpio.reset_out);
+ if (ret) {
+ dev_err(&spi->dev, "Unable to configure GPIO%d (RESET_OUT)",
+ ifx_dev->gpio.reset_out);
+ ret = -EBUSY;
+ goto error_ret6;
+ }
+
+ ret = request_irq(gpio_to_irq(ifx_dev->gpio.reset_out),
+ ifx_spi_reset_interrupt,
+ IRQF_TRIGGER_RISING|IRQF_TRIGGER_FALLING, DRVNAME,
+ (void *)ifx_dev);
+ if (ret) {
+ dev_err(&spi->dev, "Unable to get irq %x\n",
+ gpio_to_irq(ifx_dev->gpio.reset_out));
+ goto error_ret6;
+ }
+
+ ret = ifx_spi_reset(ifx_dev);
+
+ ret = request_irq(gpio_to_irq(ifx_dev->gpio.srdy),
+ ifx_spi_srdy_interrupt,
+ IRQF_TRIGGER_RISING, DRVNAME,
+ (void *)ifx_dev);
+ if (ret) {
+ dev_err(&spi->dev, "Unable to get irq %x",
+ gpio_to_irq(ifx_dev->gpio.srdy));
+ goto error_ret6;
+ }
+
+ /* set pm runtime power state and register with power system */
+ pm_runtime_set_active(&spi->dev);
+ pm_runtime_enable(&spi->dev);
+
+ /* handle case that modem is already signaling SRDY */
+ /* no outgoing tty open at this point, this just satisfies the
+ * modem's read and should reset communication properly
+ */
+ srdy = gpio_get_value(ifx_dev->gpio.srdy);
+
+ if (srdy) {
+ mrdy_assert(ifx_dev);
+ ifx_spi_handle_srdy(ifx_dev);
+ } else
+ mrdy_set_low(ifx_dev);
+ return 0;
+
+error_ret6:
+ gpio_free(ifx_dev->gpio.srdy);
+error_ret5:
+ gpio_free(ifx_dev->gpio.mrdy);
+error_ret4:
+ gpio_free(ifx_dev->gpio.reset);
+error_ret3:
+ gpio_free(ifx_dev->gpio.po);
+error_ret2:
+ gpio_free(ifx_dev->gpio.reset_out);
+error_ret:
+ ifx_spi_free_device(ifx_dev);
+ saved_ifx_dev = NULL;
+ return ret;
+}
+
+/**
+ * ifx_spi_spi_remove - SPI device was removed
+ * @spi: SPI device
+ *
+ * FIXME: We should be shutting the device down here not in
+ * the module unload path.
+ */
+
+static int ifx_spi_spi_remove(struct spi_device *spi)
+{
+ struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi);
+ /* stop activity */
+ tasklet_kill(&ifx_dev->io_work_tasklet);
+ /* free irq */
+ free_irq(gpio_to_irq(ifx_dev->gpio.reset_out), (void *)ifx_dev);
+ free_irq(gpio_to_irq(ifx_dev->gpio.srdy), (void *)ifx_dev);
+
+ gpio_free(ifx_dev->gpio.srdy);
+ gpio_free(ifx_dev->gpio.mrdy);
+ gpio_free(ifx_dev->gpio.reset);
+ gpio_free(ifx_dev->gpio.po);
+ gpio_free(ifx_dev->gpio.reset_out);
+
+ /* free allocations */
+ ifx_spi_free_device(ifx_dev);
+
+ saved_ifx_dev = NULL;
+ return 0;
+}
+
+/**
+ * ifx_spi_spi_shutdown - called on SPI shutdown
+ * @spi: SPI device
+ *
+ * No action needs to be taken here
+ */
+
+static void ifx_spi_spi_shutdown(struct spi_device *spi)
+{
+}
+
+/*
+ * various suspends and resumes have nothing to do
+ * no hardware to save state for
+ */
+
+/**
+ * ifx_spi_spi_suspend - suspend SPI on system suspend
+ * @dev: device being suspended
+ *
+ * Suspend the SPI side. No action needed on Intel MID platforms, may
+ * need extending for other systems.
+ */
+static int ifx_spi_spi_suspend(struct spi_device *spi, pm_message_t msg)
+{
+ return 0;
+}
+
+/**
+ * ifx_spi_spi_resume - resume SPI side on system resume
+ * @dev: device being suspended
+ *
+ * Suspend the SPI side. No action needed on Intel MID platforms, may
+ * need extending for other systems.
+ */
+static int ifx_spi_spi_resume(struct spi_device *spi)
+{
+ return 0;
+}
+
+/**
+ * ifx_spi_pm_suspend - suspend modem on system suspend
+ * @dev: device being suspended
+ *
+ * Suspend the modem. No action needed on Intel MID platforms, may
+ * need extending for other systems.
+ */
+static int ifx_spi_pm_suspend(struct device *dev)
+{
+ return 0;
+}
+
+/**
+ * ifx_spi_pm_resume - resume modem on system resume
+ * @dev: device being suspended
+ *
+ * Allow the modem to resume. No action needed.
+ *
+ * FIXME: do we need to reset anything here ?
+ */
+static int ifx_spi_pm_resume(struct device *dev)
+{
+ return 0;
+}
+
+/**
+ * ifx_spi_pm_runtime_resume - suspend modem
+ * @dev: device being suspended
+ *
+ * Allow the modem to resume. No action needed.
+ */
+static int ifx_spi_pm_runtime_resume(struct device *dev)
+{
+ return 0;
+}
+
+/**
+ * ifx_spi_pm_runtime_suspend - suspend modem
+ * @dev: device being suspended
+ *
+ * Allow the modem to suspend and thus suspend to continue up the
+ * device tree.
+ */
+static int ifx_spi_pm_runtime_suspend(struct device *dev)
+{
+ return 0;
+}
+
+/**
+ * ifx_spi_pm_runtime_idle - check if modem idle
+ * @dev: our device
+ *
+ * Check conditions and queue runtime suspend if idle.
+ */
+static int ifx_spi_pm_runtime_idle(struct device *dev)
+{
+ struct spi_device *spi = to_spi_device(dev);
+ struct ifx_spi_device *ifx_dev = spi_get_drvdata(spi);
+
+ if (!ifx_dev->power_status)
+ pm_runtime_suspend(dev);
+
+ return 0;
+}
+
+static const struct dev_pm_ops ifx_spi_pm = {
+ .resume = ifx_spi_pm_resume,
+ .suspend = ifx_spi_pm_suspend,
+ .runtime_resume = ifx_spi_pm_runtime_resume,
+ .runtime_suspend = ifx_spi_pm_runtime_suspend,
+ .runtime_idle = ifx_spi_pm_runtime_idle
+};
+
+static const struct spi_device_id ifx_id_table[] = {
+ {"ifx6160", 0},
+ {"ifx6260", 0},
+ { }
+};
+MODULE_DEVICE_TABLE(spi, ifx_id_table);
+
+/* spi operations */
+static const struct spi_driver ifx_spi_driver_6160 = {
+ .driver = {
+ .name = "ifx6160",
+ .bus = &spi_bus_type,
+ .pm = &ifx_spi_pm,
+ .owner = THIS_MODULE},
+ .probe = ifx_spi_spi_probe,
+ .shutdown = ifx_spi_spi_shutdown,
+ .remove = __devexit_p(ifx_spi_spi_remove),
+ .suspend = ifx_spi_spi_suspend,
+ .resume = ifx_spi_spi_resume,
+ .id_table = ifx_id_table
+};
+
+/**
+ * ifx_spi_exit - module exit
+ *
+ * Unload the module.
+ */
+
+static void __exit ifx_spi_exit(void)
+{
+ /* unregister */
+ tty_unregister_driver(tty_drv);
+ spi_unregister_driver((void *)&ifx_spi_driver_6160);
+}
+
+/**
+ * ifx_spi_init - module entry point
+ *
+ * Initialise the SPI and tty interfaces for the IFX SPI driver
+ * We need to initialize upper-edge spi driver after the tty
+ * driver because otherwise the spi probe will race
+ */
+
+static int __init ifx_spi_init(void)
+{
+ int result;
+
+ tty_drv = alloc_tty_driver(1);
+ if (!tty_drv) {
+ pr_err("%s: alloc_tty_driver failed", DRVNAME);
+ return -ENOMEM;
+ }
+
+ tty_drv->magic = TTY_DRIVER_MAGIC;
+ tty_drv->owner = THIS_MODULE;
+ tty_drv->driver_name = DRVNAME;
+ tty_drv->name = TTYNAME;
+ tty_drv->minor_start = IFX_SPI_TTY_ID;
+ tty_drv->num = 1;
+ tty_drv->type = TTY_DRIVER_TYPE_SERIAL;
+ tty_drv->subtype = SERIAL_TYPE_NORMAL;
+ tty_drv->flags = TTY_DRIVER_REAL_RAW | TTY_DRIVER_DYNAMIC_DEV;
+ tty_drv->init_termios = tty_std_termios;
+
+ tty_set_operations(tty_drv, &ifx_spi_serial_ops);
+
+ result = tty_register_driver(tty_drv);
+ if (result) {
+ pr_err("%s: tty_register_driver failed(%d)",
+ DRVNAME, result);
+ return result;
+ }
+
+ result = spi_register_driver((void *)&ifx_spi_driver_6160);
+ if (result) {
+ pr_err("%s: spi_register_driver failed(%d)",
+ DRVNAME, result);
+ tty_unregister_driver(tty_drv);
+ }
+ return result;
+}
+
+module_init(ifx_spi_init);
+module_exit(ifx_spi_exit);
+
+MODULE_AUTHOR("Intel");
+MODULE_DESCRIPTION("IFX6x60 spi driver");
+MODULE_LICENSE("GPL");
+MODULE_INFO(Version, "0.1-IFX6x60");
new file mode 100644
@@ -0,0 +1,129 @@
+/****************************************************************************
+ *
+ * Driver for the IFX spi modem.
+ *
+ * Copyright (C) 2009, 2010 Intel Corp
+ * Jim Stanley <jim.stanley@intel.com>
+ *
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA 02110-1301,
+ * USA
+ *
+ *
+ *
+ *****************************************************************************/
+#ifndef _IFX6X60_H
+#define _IFX6X60_H
+
+#define DRVNAME "ifx6x60"
+#define TTYNAME "ttyIFX"
+
+/* #define IFX_THROTTLE_CODE */
+
+#define IFX_SPI_MAX_MINORS 1
+#define IFX_SPI_TRANSFER_SIZE 2048
+#define IFX_SPI_FIFO_SIZE 4096
+
+#define IFX_SPI_HEADER_OVERHEAD 4
+#define IFX_RESET_TIMEOUT msecs_to_jiffies(50)
+
+/* device flags bitfield definitions */
+#define IFX_SPI_STATE_PRESENT 0
+#define IFX_SPI_STATE_IO_IN_PROGRESS 1
+#define IFX_SPI_STATE_IO_READY 2
+#define IFX_SPI_STATE_TIMER_PENDING 3
+
+/* flow control bitfields */
+#define IFX_SPI_DCD 0
+#define IFX_SPI_CTS 1
+#define IFX_SPI_DSR 2
+#define IFX_SPI_RI 3
+#define IFX_SPI_DTR 4
+#define IFX_SPI_RTS 5
+#define IFX_SPI_TX_FC 6
+#define IFX_SPI_RX_FC 7
+#define IFX_SPI_UPDATE 8
+
+#define IFX_SPI_PAYLOAD_SIZE (IFX_SPI_TRANSFER_SIZE - \
+ IFX_SPI_HEADER_OVERHEAD)
+
+#define IFX_SPI_IRQ_TYPE DETECT_EDGE_RISING
+#define IFX_SPI_GPIO_TARGET 0
+#define IFX_SPI_GPIO0 0x105
+
+#define IFX_SPI_STATUS_TIMEOUT (2000*HZ)
+
+/* values for bits in power status byte */
+#define IFX_SPI_POWER_DATA_PENDING 1
+#define IFX_SPI_POWER_SRDY 2
+
+struct ifx_spi_device {
+ /* Our SPI device */
+ struct spi_device *spi_dev;
+
+ /* Port specific data */
+ struct kfifo tx_fifo;
+ spinlock_t fifo_lock;
+ unsigned long signal_state;
+
+ /* TTY Layer logic */
+ struct tty_port tty_port;
+ struct device *tty_dev;
+ int minor;
+
+ /* Low level I/O work */
+ struct tasklet_struct io_work_tasklet;
+ unsigned long flags;
+ dma_addr_t rx_dma;
+ dma_addr_t tx_dma;
+
+ int is_6160; /* Modem type */
+
+ spinlock_t write_lock;
+ int write_pending;
+ spinlock_t power_lock;
+ unsigned char power_status;
+
+ unsigned char *rx_buffer;
+ unsigned char *tx_buffer;
+ dma_addr_t rx_bus;
+ dma_addr_t tx_bus;
+ unsigned char spi_more;
+ unsigned char spi_slave_cts;
+
+ struct timer_list spi_timer;
+
+ struct spi_message spi_msg;
+ struct spi_transfer spi_xfer;
+
+ struct {
+ /* gpio lines */
+ unsigned short srdy; /* slave-ready gpio */
+ unsigned short mrdy; /* master-ready gpio */
+ unsigned short reset; /* modem-reset gpio */
+ unsigned short po; /* modem-on gpio */
+ unsigned short reset_out; /* modem-in-reset gpio */
+ /* state/stats */
+ int unack_srdy_int_nb;
+ } gpio;
+
+ /* modem reset */
+ unsigned long mdm_reset_state;
+#define MR_START 0
+#define MR_INPROGRESS 1
+#define MR_COMPLETE 2
+ wait_queue_head_t mdm_reset_wait;
+};
+
+#endif /* _IFX6X60_H */
new file mode 100644
@@ -0,0 +1,14 @@
+#ifndef LINUX_IFX_MODEM_H
+#define LINUX_IFX_MODEM_H
+
+struct ifx_modem_platform_data {
+ unsigned short rst_out; /* modem reset out */
+ unsigned short pwr_on; /* power on */
+ unsigned short rst_pmu; /* reset modem */
+ unsigned short tx_pwr; /* modem power threshold */
+ unsigned short srdy; /* SRDY */
+ unsigned short mrdy; /* MRDY */
+ unsigned short is_6160; /* Modem type */
+};
+
+#endif